This makes it easier to test various X.509 certificate validation steps
with the server certificate being generated and signed using pyOpenSSL
dynamically.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
cfg80211 was modified to allow the Multiple BSSID Index element to be
included in the IEs for a nontransmitted BSS. Update the validation step
in this test case to allow that different with the IEs in the Beacon
frame (transmitted BSS).
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Reduce testing dependency on the unsuitable groups so that a test case
against a production build would not fail the test case unnecessarily.
This is in preparation of making production builds
(CONFIG_TESTING_OPTIONS not defined) of wpa_supplicant hostapd disable
all DH groups that have been indicated as being unsuitable.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
FLUSH should be done on P2P device interface, otherwise the networks are
not removed. Fix that.
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
The separate dpp_bootstrap_gen() functions were merged into a single
one, so the test case needs a matching change to avoid failures.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Increase testing coverage by going through all six possible curves with
full provisioning of AP and STA and connection (which includes PFS with
DPP2).
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
This test case did not clear a possibly modified sae_groups value from a
prior test case for adev[2] and could fail if the previously set group
was not supported by the AP.
Signed-off-by: Jouni Malinen <j@w1.fi>
These test cases did not clear a possibly modified sae_groups value from
a prior test case and could fail if the previously set group was not
supported by the AP.
Signed-off-by: Jouni Malinen <j@w1.fi>
This test case did not clear a possibly modified sae_groups value from a
prior test case and could fail if the previously set group was not
supported by the AP.
Signed-off-by: Jouni Malinen <j@w1.fi>
Use a helper function to perform this common sequence to disconnect and
stop any possibly started reconnection attempt.
Signed-off-by: Jouni Malinen <j@w1.fi>
If the ABORT_SCAN command succeeds, CTRL-EVENT-SCAN-RESULTS event is
delivered for the aborted scan. Following this with an immediate
flush_scan_cache() call can result in the first scan interpreting that
pending event as the completion and that results in trying to start
another scan while the first scan is still in progress.
Signed-off-by: Jouni Malinen <j@w1.fi>
This is needed to avoid leaving behind a ROC operation at the end of the
test case. This was found with the following test sequence:
p2p_ext_vendor_elem_invitation wifi_display_r2
Signed-off-by: Jouni Malinen <j@w1.fi>
Parsing of the DER encoded signature was unable to handle results that
were shorter than the prime. These need to be zero padded from left to
generate the correct value.
Signed-off-by: Jouni Malinen <j@w1.fi>
The long wait for the monitor socket events resulted in another socket
running out of TX buffer space. Split the wait into smaller segments and
clear the other socket in each iteration.
Signed-off-by: Jouni Malinen <j@w1.fi>
Do not leave all the event messages pending in the socket queue for the
full duration of the test case to avoid hitting the TX socket queue
limit.
Signed-off-by: Jouni Malinen <j@w1.fi>
Some of the test cases left behind attached control interface monitor
sockets that could result in hitting the wpa_supplicant socket TX queue
limit. Try to be a bit more careful about detaching and closing the
sockets to avoid this.
Signed-off-by: Jouni Malinen <j@w1.fi>
The "_ipv6" part of the file name was missing and this resulted in file
names that conflicted with the IPv4 test cases and could overwrite logs
for those.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
It does not look like there would be two CTRL-EVENT-ASSOC-REJECT events
here, so only check the first one instead of requiring both to be
received with status_code=27. This test case could fail based on the
second connection attempt (due to that extra event wait) timing out.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Print a list of full paths to log files from failed test cases both the
parallel.log and stdout so that they can be easily opened for analysis.
In addition, renumber the VM lines in the <timestamp>-parallel.log to
match the i+1 numbering used in the log directories and UI that is
tracking test execution.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
One of the steps that expected failure due to PMKID mismatch did not
stop connection attempts. This could result in the following test step
failing due to the previous profile with peaplabel=1 getting used to
derive the MSK incorrectly.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
The wait_event() call for scan completion could have processed a
previously received event from a prior scan instead of the newly started
one. This could result in flush_scan_cache() assuming there are still
results in the cache even though the scan request to clear the cache had
not even be started yet.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Use more readable "foo not in bar" construction for the couple of places
that did "not foo in bar".
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Prior cleanup broke the indentation here and made the addition of test
cases unreachable.
Fixes: 0663ae22ff ("tests: Do not use tabs for indentation")
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
The new DPP Configuration Result message can result in a bit different
behavior at the end of the configuration exchange and some of the test
cases need more flexibility to work with that DPP2 behavior.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
gas_address3 was set to 1 in this test case, but it was never cleared.
That can result in unexpected behavior in other test cases that dpeends
on gas_address3 being in its default value 0. Clear the parameter
explicitly to avoid this.
This resulted in an error in the following test sequence:
dpp_qr_code_auth_initiator_enrollee gas_anqp_address3_ap_forced
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
There was a race condition on starting the flush_scan_cache() operations
if a scan happened to be in progress when the test case ended since the
ABORT_SCAN success case did not wait for the pending scan operation to
be completed. Wait for the scan completion event in addition to the
disconnection event if the ABORT_SCAN command is accepted.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
There was a race condition on starting the flush_scan_cache() operations
if a scan happened to be in progress when the test case ended since the
ABORT_SCAN success case did not wait for the pending scan operation to
be completed. Wait for the scan completion event in addition to the
disconnection event if the ABORT_SCAN command is accepted.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
These TDLS test cases missed Popen() result decode() calls in the
earlier python3 compatibility changes. Add those to make debug log more
readable.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Wait explicitly for the DPP-NOT-COMPATIBLE event when going through
protocol testing with local failures instead of just waiting for a fixed
0.1 second duration. This prevents a test failure at least in
dppauth_resp_status_failure in a case where the failing operation may be
delayed under heavy CPU load.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Test case sequence "ap_wps_ap_scan_2 ap_wps_pbc_2ap" resulted in a
failure due to a scan entry being left behind from the first test case
and the second one ending up using that obsolete result during WPS_PBC
processing. Fix this by clearing the scan results explicitly on dev5.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Accept a smaller number of token responses in second round to avoid
failing this test case as frequently.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
The configurated fragmentation/RTS threshold value survives AP mode
interface restarts, so these values need to be explicitly cleared back
to default (disabled). This fixes an issue where some test cases could
not work correctly if fragmentation on the interface was enabled. For
example, this combination used to fail:
ap_fragmentation_open ap_hs20_fetch_osu
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
The first scan for the unknown BSSID could have been timed in a manner
that allows passive scanning to find the real AP even if that AP's
beacon interval was 1000 (e.g., heavy CPU load changed timing so that
the AP beaconing started at suitable time). The check for BSS result
entry not including Probe Response frame was comparing incorrect BSS
entries (bss2 vs. bss1) which resulted in the test case claiming failure
even when there was no unexpected Probe Response frame.
Fix this by comparing the beacon_ie and ie parameters from the same BSS
entry (bss1).
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Number of these test cases start connection attempt in wpa_supplicant
and then expected a specific failure to happen relatively quickly. This
could result in timeouts if the first scanning round missed to find the
AP (e.g., due to CPU load pushing out the Probe Response frame long
enough for the station having left the channel) and wpa_supplicant then
waiting five seconds before starting a new scan.
Make this more robust by scanning explicitly for the specific BSSID
before starting the connection attempt.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
This old interface has been obsoleted and should not have been used
since 2010, so remove testing for it in preparation to dropping the
interface completely from wpa_supplicant.
Signed-off-by: Lubomir Rintel <lkundrak@v3.sk>
No need to duplicate this functionality when all the ap_ft_pmf_*_over_ds
test cases are doing practically the same thing and the
no-specific-cipher-configuration case can be addressed easily with the
same helper function.
Signed-off-by: Jouni Malinen <j@w1.fi>
The main step of the test case was accidentally removed when adding the
cipher specific versions.
Fixes: ffcaca68d3 ("tests: FT with different BIP algorithms")
Signed-off-by: Jouni Malinen <j@w1.fi>
Configure the sae_groups parameter for hostapd explicitly in preparation
for the default value change in the implementation.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Configure the sae_groups parameter for hostapd explicitly in preparation
for the default value change in the implementation.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Avoid an invalid failure case due to scan results being left behind from
connect_cmd_bssid_hint when executing connect_cmd_reject_assoc by
explicitly clearing the scan results from dev5. This fixes an error case
that happened with the following test case sequence:
connect_cmd_bssid_hint connect_cmd_reject_assoc
Signed-off-by: Jouni Malinen <j@w1.fi>
The wpas (dev5) control interface socket did not always get cleared in
the MACsec test cases and this could result in issues with following
test cases if the dev5 message queue hit the maximum limit.
Signed-off-by: Jouni Malinen <j@w1.fi>
Now that the backhaul STA Multi-AP association is not rejected anymore
by the AP, update the test case to expect disconnection to be triggered
by the STA.
Signed-off-by: Arnout Vandecappelle (Essensium/Mind) <arnout@mind.be>
With just one additional argument, the run_multi_ap_association()
function can be used for all tests.
Signed-off-by: Arnout Vandecappelle (Essensium/Mind) <arnout@mind.be>
This seems to be needed when using python3 in VM for the ssid_utf8 test
case debug prints from the control interface requests. This breaks
python2 support for the same logging entries, but there does not seem to
be any easy way of addressing this in a manner that works for both
python versions, so move ahead with the python3-only support from now
on.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
This test case was failing pretty frequently due to an issue in being
able to send out the Provision Discovery Response frame on the operating
channel. Now that wpa_supplicant has a fix for that issue, modify this
test case to hit this error condition every time. In addition, make sure
the possible exception from p2ps_exact_seek() does not get hidden with a
failing remove_group() call in the finally section.
Signed-off-by: Jouni Malinen <j@w1.fi>
Once mac80211 starts reporting the used Association Request frame IEs in
the association event, wpa_supplicant will update RSN supplicant IE
information based on that and that will make the AP reject EAPOL-Key msg
2/4 in this particular test scenario due to the hack of including two
RSN IEs in the Association Request frame. Accept this sequence as a
valid test execution in addition to the previously expected connection
to avoid reporting incorrect failures.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
This allows unexpected cases to terminate parallel-vm.py without being
hidden by the exception handler.
Signed-off-by: Masashi Honma <masashi.honma@gmail.com>
Some of the WNM implementation expects configuration to be available
(e.g., ieee802_!1_rx_wnm_coloc_intf_req() dereferences wpa_s->conf), so
add a dummy configuration to allow the fuzzer tool to be used.
Signed-off-by: Jouni Malinen <j@w1.fi>
Add test-eapol program that can be used for fuzzing the EAPOL-Key
Supplicant and Authenticator implementations. This tool can write
Supplicant or Authenticator messages into a file as an initialization
step and for the fuzzing step, that file (with potential modifications)
can be used to replace the internally generated message contents.
The TEST_FUZZ=y build parameter is used to make a special build where a
hardcoded random number generator and hardcoded timestamp are used to
force deterministic behavior for the EAPOL-Key operations. This will
also make the implementation ignore Key MIC and AES keywrap errors to
allow processing of modified messages to continue further.
Signed-off-by: Jouni Malinen <j@w1.fi>
Add test-tls program that can be used for fuzzing the internal TLS
client and server implementations. This tool can write client or server
messages into a file as an initialization step and for the fuzzing step,
that file (with potential modifications) can be used to replace the
internally generated message contents.
The TEST_FUZZ=y build parameter is used to make a special build where a
hardcoded random number generator and hardcoded timestamp are used to
force deterministic behavior for the TLS operations.
Signed-off-by: Jouni Malinen <j@w1.fi>
The result of reading non blocked empty stream is different between
python2 and 3. The python2 sends "[Errno 11] Resource temporarily
unavailable" exception. The python3 could read "None" without
exception, so handle this "None" case as well.
Signed-off-by: Masashi Honma <masashi.honma@gmail.com>
In recent Debian versions, ebtables is an alias managed by
the alternatives(8) mechanism. This means /usr/sbin/ebtables
is a symlink to /etc/alternatives/ebtables, which in turn
links to the real binary.
As we mount a tmpfs over /etc, we cannot access this.
Fix this by bind-mounting the real /etc to /tmp/etc and
adding a symlink from /etc/alternatives to this.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Evidently this file must exist when running the sigma_dut
dependent tests, add it to .gitignore so it's not seen as
making the tree "unclean" when it is added manually.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
For tests, build the HS 2.0 OSU client (without browser to avoid
having webkit/curl dependencies).
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Add a test that drops the authentication frame, so that
hostapd thinks the station is unknown, and then sends one
by itself, so the station thinks it's associated. This
tests mostly the kernel's capability to recover from this
scenario.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
If telnetd is installed and --telnet <port> is passed on the
vm-run.sh command line, start a telnet server (directly connected
to bash, no login) inside the VM(s) to be able to look into them
when something is wrong. Use a user network in qemu with a single
host forward from the specified port for this, listening only on
'localhost'.
Please note that this provides unauthenticated access to the guest
system from anything that can open a TCP connection on the host system.
The guess system does have access to reading all files on the host that
the user account running kvm has access to (and even write access if the
default ROTAG ,readonly parameter is cleared). In other words, this
option should not be used on any multiuser systems where kvm is run
under user accounts that are not dedicated for testing purposes (i.e.,
do not have access to any files that should not be readable to
everyone).
This needs CONFIG_VIRTIO_NET=y in the guest kernel.
For parallel-vm.py, the --telnet argument specifies the base port
and each VM index (0, 1, ...) is added to it.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Recently, qemu/seabios grew an annoying console/terminal reset,
which also causes my terminal to be left in a state where long
lines don't work well and less gets confused because of this.
Suppress this by suppressing all output from qemu before a new
magic string printed from inside.sh.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Instead of relying on existing configuration (which may conflict
with other tests) and skipping otherwise, create a new radio with
two channels in this test and use it.
Signed-off-by: Jouni Malinen <j@w1.fi>
Instead of relying on existing configuration (which may conflict
with other tests) and skipping otherwise, create a new radio with
two channels in this test and use it.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This is needed to fix issues with dict iteration resulting in different
order of attributes when trying to calculate Message-Authenticator
externally to pyrad.
Signed-off-by: Jouni Malinen <j@w1.fi>
All other test cases seem to work, but radius_das_disconnect_time_window
is still failing due to incorrect authenticator or Message-Authenticator
in Disconnect-Request.
Signed-off-by: Jouni Malinen <j@w1.fi>
Sending UTF-8 encoded data to logger file is currently not working
properly, so create a separate binary file with a copy of
sigma_dut-ap.conf instead to work with both python2 and python3.
Signed-off-by: Jouni Malinen <j@w1.fi>
Use struct.unpack() to get a list of int and then generate a list of
hexstr octets from it for ':'.join() to get consistent behavior for both
python2 and python3.
Signed-off-by: Jouni Malinen <j@w1.fi>
WPSAPHTTPServer class needs to explicitly decode the read value from
a bytes object to a str object.
Signed-off-by: Masashi Honma <masashi.honma@gmail.com>
Use ET.tostring() to avoid implicit bytes/str conversion issues within
ET implementation. Add XML declaration separately to match previous
behavior.
Signed-off-by: Masashi Honma <masashi.honma@gmail.com>
This is needed for python3 since the two argument version of
str.translate() is not available for unicode. Furthermore, these cases
of delete colons from the string are simple enough for replace.
Signed-off-by: Jouni Malinen <j@w1.fi>
Only python3 warns to this bug.
TypeError: '>' not supported between instances of 'type' and 'int'
Exception: '>' not supported between instances of 'type' and 'int'
Signed-off-by: Masashi Honma <masashi.honma@gmail.com>
Need to do this to avoid issues with following operations that assume
the output to be a str object.
Signed-off-by: Masashi Honma <masashi.honma@gmail.com>
Avoid implicit conversion errors when constructing bytes objects or
passing a str object to a function that needs a bytes object.
Signed-off-by: Masashi Honma <masashi.honma@gmail.com>
Signed-off-by: Jouni Malinen <j@w1.fi>
The wpas_config_file_key_mgmt fails with this error if wpa_supplicant is
built without CONFIG_SUITEB192=y:
Exception: SET_NETWORK failed
Exception: SET_NETWORK failed
Skip the WPA-EAP-SUITE-B-192 case if it is not supported in
wpa_supplicant so that the rest of the key_mgmt test coverage is
included.
Signed-off-by: Masashi Honma <masashi.honma@gmail.com>
This is needed in cases the hexlify() output is used to concatenate with
a string or used in string comparisons.
Signed-off-by: Masashi Honma <masashi.honma@gmail.com>
Signed-off-by: Jouni Malinen <j@w1.fi>
This patch is made by using 2to3 command with some modifications.
$ find . -name *.py | xargs 2to3 -f imports -w -n
Signed-off-by: Masashi Honma <masashi.honma@gmail.com>
These were not used at all and caused unnecessary operations and in some
cases, compatibility issues with python3.
Signed-off-by: Jouni Malinen <j@w1.fi>
This code is identical to the wait_event() code, except for the
mon/global_mon instance. Create a _wait_event() function that
encapsulates this, and use it for both.
While at it, fix the bug in wait_global_event() where in the case
of not having a global_mon it always returns None.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This is useful when running a test multiple times, looking at
log output etc. to not have to pick out the right directory
each and every time.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The wnm_sleep_mode_proto test case was already covering number of
invalid WNM-Sleep Mode Request frame cases, but it was missing the
shortest possible case with a missing Dialog Token field. Add that as a
regression test case for bounds checking in
ieee802_11_rx_wnmsleep_req().
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Since 3bdc651a62, start.sh creates the logs/current symlink even if
LOGDIR was set in the environment, as is the case when using run-all.sh.
However, run-all.sh and start.sh use a separate 'date' invocation so the
resulting string may be different. Usually it is the same because the
two invocations immediately follow each other, *except* if run-all.sh
also does a build. In addition, if the user sets LOGDIR to something
else, the symlink is completely bogus.
Fix this by not relying on the 'date' invocation for creating the
symlink. Instead, use the basename of LOGDIR. To keep things consistent
with current behavior, only create the symlink if LOGDIR points to a
subdirectory of DIR/logs.
The following use cases now work reliably:
* run-all.sh with or without the -B option;
* manually calling start.sh followed by run-tests.py without setting
LOGDIR.
* manually calling start.sh with LOGDIR set to a subdirectory of logs
and calling run-tests.py without --logdir option (which makes it
default to logs/current).
* run-all.sh with LOGDIR set to a subdirectory of logs.
Signed-off-by: Arnout Vandecappelle (Essensium/Mind) <arnout@mind.be>
This is in preparation for an implementation change that results in this
unreachable server case not incrementing radiusAuthClientAccessRequests.
Signed-off-by: Jouni Malinen <j@w1.fi>
These checks were repeated in almost every test case, so use helper
functions to get rid of duplicated (copy-pasted) code.
Signed-off-by: Jouni Malinen <j@w1.fi>
Add even more workarounds for cfg80211 regulatory state clearing since
these DFS test cases seem to be the most likely ones to fail due to
country=98 issues.
Signed-off-by: Jouni Malinen <j@w1.fi>
Add even more workarounds for cfg80211 regulatory state clearing since
these DFS test cases seem to be the most likely ones to fail due to
country=98 issues.
Signed-off-by: Jouni Malinen <j@w1.fi>
Add even more workarounds for cfg80211 regulatory state clearing since
these WNM test cases seem to be the most likely ones to fail due to
country=98 issues.
Signed-off-by: Jouni Malinen <j@w1.fi>
In addition, add even more workarounds for cfg80211 regulatory state
clearing since this test case seems to be the most likely one to fail
due to country=98 issues.
Signed-off-by: Jouni Malinen <j@w1.fi>
This is a regression test case for FT-over-DS that got broken on
mac80211-based drivers when the extra key reinstallation checks were
added.
Signed-off-by: Jouni Malinen <j@w1.fi>
ap_ft_oom seemed to depend on undesired wpa_supplicant behavior of
trying to do FT protocol even without being ready for reassociation.
This is going to be fixed in wpa_supplicant which would make this test
case fail, so split it into separate test cases for each failure item to
be able to avoid incorrect test failures.
Signed-off-by: Jouni Malinen <j@w1.fi>
The previous roam() and roam_over_ds() checks would have ignored failing
association rejection if a consecutive attempt to connect succeeds
within the initial time limit. This can miss incorrect behavior, so
check explicitly for association rejection.
Signed-off-by: Jouni Malinen <j@w1.fi>
The number of direct allocation within wpa_supplicant_mesh_init()
has been reduced due to RSN init function is factored out.
Signed-off-by: Peter Oh <peter.oh@bowerswilkins.com>
Verify that the beacon report contains the last beacon report
indication subelement when requested in the beacon request.
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
Verify that when the frame body subelement causes the
measurement report element to exceed the maximum element size,
the beacon report is fragmented and the frame body fragment ID
subelement is added with the correct fragment number.
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
Verify that not updating GTK (i.e., only update PTK) in the driver does
not break connectivity. This case is different after the check for
"already in-use GTK" and rejection of GTK reinstallation.
Signed-off-by: Jouni Malinen <j@w1.fi>
Use of country=00 (world roaming) seemed to not work anymore with the
current cfg80211 regulatory implementation since the existing channel is
left enabled when moving to country=00. Use a specific country code that
does enforce the selected channel from being used anymore to make this
test case pass again.
The change in cfg80211 behavior is from the kernel commit 113f3aaa81bd
("cfg80211: Prevent regulatory restore during STA disconnect in
concurrent interfaces").
Signed-off-by: Jouni Malinen <j@w1.fi>
With this command, RSSI signal can be controlled. Due to restrictions in
kernel, only values in the range of [-30, -50] can be used. The command
is implemented by changing the TX power.
Signed-off-by: Beni Lev <beni.lev@intel.com>
It was possible for the 5 GHz PKEX channels to be enabled, e.g., when
running "ap_ht40_csa2 dpp_pkex_no_responder" test sequence, and that
resulted in a failure in dpp_pkex_no_responder due to the unexpectedly
long wait needed for the DPP-FAIL event. Increase the wait time to allow
for 5 GHz PKEX channels to be probed.
Signed-off-by: Jouni Malinen <j@w1.fi>
This allows more accurate logging of failures related to the cfg80211
country=98 (intersection) case. This version is trying to give some more
time to allow the country code to clear, but that does not seem to be
sufficient with the current cfg80211 implementation for country=98 (but
might be for other cases).
The additional check for country=98 at the beginning of each test case
is an attempt to force cfg80211 to restore world roaming state with a
new association and disconnection at the station side detected after the
AP side has already stopped. This is needed after the Linux kernel
commit 113f3aaa81bd ("cfg80211: Prevent regulatory restore during STA
disconnect in concurrent interfaces").
Signed-off-by: Jouni Malinen <j@w1.fi>
This is needed to avoid leaving unexpected cfg80211 regulatory country
code in place at the point when a test case terminates.
Signed-off-by: Jouni Malinen <j@w1.fi>
Previously, the special value 0 was used to indicate no UDP checksum.
Replace that with the calculated checksum for more like use case.
Signed-off-by: Jouni Malinen <j@w1.fi>
The ap_open_tdls_vht* test cases could leave some pending regulatory
Beacon hints waiting to be cleared during the following test case. This
would result in a failure if the following test case expected specific
regdom event behavior. For example, this caused "ap_open_tdls_vht160
dbus_country" sequence to result in failure in dbus_country. Fix this by
using more robust sequence in clearing regdom state at the end of the
TDLS test cases that have the AP advertising a country code.
Signed-off-by: Jouni Malinen <j@w1.fi>
Not all driver interfaces provide driver status information with the
local address, so skip the override step if the field is not available.
This is needed, e.g., with macsec_linux.
Signed-off-by: Jouni Malinen <j@w1.fi>
Add a new test to check that the AP won't send frames to the client if
it tries to talk to itself.
Note that this fails until the relevant mac80211 patch is merged.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
These test cases seemed to have copy-paste errors where
wait_enabled=False was forgotten even though there was no additional
steps checking the AP mode startup results. This did not break the
tests, but could have resulted in slowing them down if the STAs did not
find the AP in the first scan.
Signed-off-by: Jouni Malinen <j@w1.fi>
The Linux kernel commit 113f3aaa81bd ("cfg80211: Prevent regulatory
restore during STA disconnect in concurrent interfaces") broke the
regulatory clearing attempt in many test cases since
cfg80211_is_all_idle() is now returning false due to the AP interface
being up and that results in the Country IE -based regulatory
information not getting cleared back to defaults.
Work around this by stopping the AP interface first so that when the
station interface receives the disconnection, there are no other active
interfaces in the system. In addition, wait for REGDOM event for the
Country IE hint after association to avoid disconnection before the
regulatory events have been fully processed.
Signed-off-by: Jouni Malinen <j@w1.fi>
The Linux kernel commit 113f3aaa81bd ("cfg80211: Prevent regulatory
restore during STA disconnect in concurrent interfaces") broke the
regulatory clearing attempt in this test case since
cfg80211_is_all_idle() is now returning false due to the AP interface
being up and that results in the Country IE -based regulatory
information not getting cleared back to defaults.
Work around this by stopping the AP interface first so that when the
station interface receives the disconnection, there are no other active
interfaces in the system. In addition, wait for REGDOM event for the
Country IE hint after association to avoid disconnection before the
regulatory events have been fully processed.
Signed-off-by: Jouni Malinen <j@w1.fi>
cfg80211 regulatory code gets into pretty inconvenient state if it needs
to intersect regulatory domain information from multiple regulations
(country=98). The existing mechanisms in the hwsim test cases are not
able to clear that up for the following test case and this can result in
large number of failures.
It looks like country=98 case is hit frequently in WNM test cases where
a station associates with an AP that advertises a specific country code
and that station is then asked to disconnect before the REGDOM events
have been received. Avoid this by waiting for the REGDOM events for the
init=COUNTRY_IE case before disconnecting.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
This adds some minimal testing for Multi-BSS connection attempts. The
part for nontransmitted BSS is limited since hostapd/mac80211 does not
yet have sufficient support for Multi-BSS in AP mode.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Perform detailed tests with OCV enabled, for both the 4-way and group
key handshakes. These tests include establishing a working connection
with OCV enabled, assuring that a STA without OCV enabled can still
connect to a STA with OCV enabled (and vice versa), verifying that
invalid OCI elements get silently ignored, verifying that missing OCI
elements are reported, and so on.
Signed-off-by: Mathy Vanhoef <Mathy.Vanhoef@cs.kuleuven.be>
parallel-vm.py has obsoleted this a long time ago and there is no need
to maintain two scripts for doing more or less the same thing.
Signed-off-by: Jouni Malinen <j@w1.fi>
Now that hostapd starts mandating PMF for Hotspot 2.0 Release 2
association, this test case needs some more tweaks to work. Hardcode
Hotspot 2.0 Release 1 to be used and disable PMF explicitly.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
The Beacon loss event was not reported anymore, so remove that as an
unnecessary step in the test case. In addition, check the key_mgmt
values explicitly.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
This is needed to meet the Hotspot 2.0 Release 2 requirement for the
third station that is actually using RSN.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Match the implementation change to fix the test cases that verified a
specific Hotspot 2.0 release number indication.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
This is a regression test case for a potential NULL pointer
dereferencing fixed in the previous commit.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
This verifies that radio measurement capabilities are negotiated
correctly for the reassociation cases with and without FT.
Signed-off-by: Jouni Malinen <j@w1.fi>
There is no point in building this tarball in /tmp that is on the
ramdisk of the VM since it will go away when the VM exits.
Signed-off-by: Jouni Malinen <j@w1.fi>
The call to remove_group() may fail, in which case all following
cleanup is skipped. This may result in failing many tests since
cleanup did not complete successfully.
Fix this by calling remove_group() after other cleanup is done so
even it fails it will not affect the following tests.
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
Implement ECDSA signing functionality in the Python test script for
generating a valid signedConnector. This allows coverage of DPP config
object testing to be increased more easily.
Signed-off-by: Jouni Malinen <j@w1.fi>
Based on Jouni Malinen's [76055b4c6 "tests: D-Bus Get/Set Pmf"], modified
to use the correct "s" signature for the "Pmf" property.
Removed the negative test cases, because the synthesized property doens't
seem to do error checking upon being set.
Signed-off-by: Jouni Malinen <j@w1.fi>
Signed-off-by: Lubomir Rintel <lkundrak@v3.sk>
The hwsim's start.sh script spawns hostapd process using "sudo".
Since sudo forks a child process, $! holds the pid of sudo itself.
Fix that by storing the PID of the child process instead.
Since in VM "sudo" is replaced with a dummy script, pass an additional
argument to run-all.sh and start.sh scripts to indicate that they are
running inside a VM.
This is needed to fix ap_config_reload and ap_config_reload_file test
cases on some platforms where sudo is apparently not relaying the
signals properly.
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
In ap_acl_deny test, the AP doesn't send probe responses during scan due
to ACL reject. As the result, dev[0] might miss the AP's Beacon frame
because the dwell time is too short. Make the test more robust and
trigger passive scan, and by that increase the probability of hearing
the AP.
Signed-off-by: Ayala Beker <ayala.beker@intel.com>
The OSU Providers List includes two providers, so there should be two
OSU_METHOD values listed just like there was two OSU_SERVER_URI URLs.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
This is needed to allow sigma_dut to enable ap_isolate=1. In addition,
verify that the two associated STAs with RSN(EAP) and OSEN cannot
exchange frames between them.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
P2P related configuration should be done on a global control interface.
This way this test can be reused also when a dedicated P2P device
interface is used.
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
It looks like tshark parser was broken at some point for
wlan.mesh.config.cap which is now (tshark 2.6.3) pointing to incorrect
field (same as wlan.mesh.config.ps_protocol). This used to work with
tshark 2.2.6.
For now, assume the capability field ends up being the last octet of the
frame.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
It looks like at least tshark 2.6.3 uses a different error message for
unknown display filter fields:
tshark: Neither "wlan_mgt.fixed.category_code" nor "4" are field or protocol names.
and a different status exit code (2 instead of 1).
Add a new handler for this combination to allow automatic wlan_mgt to
wlan conversion to happen.
Signed-off-by: Jouni Malinen <j@w1.fi>
This test starts two identical APs and assumes a connection to the first
one, though it is not necessary true. Fix that by starting the second AP
only after the connection is established.
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
This test case had an error that hit an unexpected disconnection. Add an
explicit check to verify that this does not happen anymore.
Signed-off-by: Jouni Malinen <j@w1.fi>
The channel configuration in CHAN_SWITCH command was incorrect. This
resulted in switching to HT40+ channel, while announcing HT40- in the
secondary channel IE. This caused a disconnection after the channel
switch. Fix that.
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
Verify that PMF does not end up reporting unexpected status code 30
(temporary rejection; SA Query).
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
This verifies that wpa_supplicant and hostapd behave consistently with
PMKSA caching when Suite B AKMs end up deriving a new PMKID from each
4-way handshake.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
This is a regression test case for a memory leak on DPP_CONFIGURATOR_ADD
error path in dpp_keygen_configurator() when an unsupported curve is
specified.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Verify that the automatically generated network profile is able to
connect to a non-FT network automatically after having used FT for the
first connection.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Verify that EAP-AKA' client rejects Challenge with an appended AT_KDF
and a modified AT_KDF value during KDF negotiation.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Check that the @1@ macro gets replaced correctly both when in the middle
and when in the end of the URL template.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
This is needed with the modified hostapd implementation to fix the
ap_hs20_terms_and_conditions* test cases.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
It is easier to understand the hostapd debug log here if each step is
noted there before starting the wpa_supplicant operation. In addition,
it looks safer to process all pending event messages between each step
to avoid running out of any buffer limits.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
This test case verifies that wpa_supplicant is able to perform CSA to a
VHT80 channel when having to move the GO due to an avoid-frequencies
driver event.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
The implementation changes in hostapd FT error path handling in the
follow commit would result in ap_ft_ap_oom7 test case failing. This is
triggered partially by PMF protections and SA Query attempts, so it
looks like it is easier to split each failure case into a separate test
case.
Signed-off-by: Jouni Malinen <j@w1.fi>
Couple of "invalid value" tests started to fail now that mac80211_hwsim
actually accepts power save configuration. Fix these by running the same
command for more code coverage, but in a way that ignores the result of
the operation (succeeds with older kernel versions and fails with
newer).
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
For testing purposes, enable TLS v1.3 in the authentication server so
that the protocol version can be controlled from wpa_supplicant side
more easily.
Signed-off-by: Jouni Malinen <j@w1.fi>
It looks like OpenSSL 1.1.1 accepted the openssl_ciphers=FOO test
configuration or well, at least does not reject it like previous
versions did. For now, ignore this failure.
Signed-off-by: Jouni Malinen <j@w1.fi>
RC4-SHA cipher case ended up allowing the handshake to be started just
to fail with "no ciphers available" when trying to generate ClientHello.
Fix this by handling an EAP failure case for the RC4-SHA test step with
OpenSSL 1.1.*.
Signed-off-by: Jouni Malinen <j@w1.fi>
Verify that the AP initialization failure is reported back to
wpa_supplicant also when the initialization is complete in a callback.
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
time.sleep() in run_roams() is required because the target AP sets the
key once the station was associated. There are races, when the station
processes the (Re)Association Response frame AND the test suite starts
FT_DS before the AP processes its local confirmation and thus
wpa_auth_sm_event(ASSOC_FT). Therefore, the ActionFrame will be lost, as
the AP driver is missing the key.
Since this is this speed is highly synthetic, wait a few milliseconds
before roaming back.
Signed-off-by: Michael Braun <michael-dev@fami-braun.de>
This is a regression test for a sequence where wpa_supplicant interface
MAC address is changed externally and the ifdown-ifup sequence is
processed only after the interface has already been set UP.
Signed-off-by: Jouni Malinen <j@w1.fi>
Test the hostapd venue_url configuration parameter. In addition, fix the
previous defined gas_anqp_venue_url test case to use correct encoding of
the Venue URL ANQP-element payload (URLs were missing and Venue Number
was off-by-one).
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
This test case uses EAP-MSCHAPv2 within the PEAP tunnel, so verify that
the build includes support for that before running the test.
Signed-off-by: Sean Parkinson <sean@wolfssl.com>
Enable appropriate Suite B test cases with BoringSSL. Currently, this
means enabling only the 192-bit level ECDSA and ECDHE-RSA since
BoringSSL has removed support for DHE and there is no need to support
128-bit level ECDSA anymore.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
On Fedora 26, start.sh fails with these error messages.
Failed to connect to wpa_supplicant global interface: /tmp/wpas-wlan0 error: Permission denied
Failed to connect to wpa_supplicant global interface: /tmp/wpas-wlan0 error: Permission denied
...
This is because Fedora 26 uses "wheel" group as administrative group.
Signed-off-by: Masashi Honma <masashi.honma@gmail.com>
This is used in the tests, too, and was already covered by the build.sh
script, but not this README file.
Signed-off-by: Vasyl Vavrychuk <vvavrychuk@gmail.com>
Clear the model_name parameter back to the default (empty string) at the
beginning and the end of dbus_set_global_properties to avoid failures if
the test case is run multiple times.
Signed-off-by: Jouni Malinen <j@w1.fi>
Ignore any unexpected deviceLost event before the peer devices has been
discovered. This works around issues where the previous test case
terminates before the D-Bus events have been fully delivered. This could
happen, e.g., when running dbus_p2p_discovery twice in a row.
Signed-off-by: Jouni Malinen <j@w1.fi>
Wait for the configuration exchange to complete before issuing the
DPP_STOP_LISTEN command to avoid confusing sequence of operation between
the ongoing and immediately following DPP exchanges.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Fix bssid2 value to make scanning more reliable for the second OWE BSS.
In addition, reorder the STA status checks to happen before the data
connectivity check to get more accurate failure reason into the log if
the test case fails.
Signed-off-by: Jouni Malinen <j@w1.fi>
Linux kernel commit c9491367b759 ("mac80211: always update the PM state
of a peer on MGMT / DATA frames") enforces the AP to check only
mgmt/data frames PM bit, and to update station's power save accordingly.
When sending only a PS-Poll (control frame) the AP will ignore the PM
bit. As the result, the partial virtual bitmap will not be updated, and
the test ap_open_disconnect_in_ps will fail on tshark check. Since the
test needs only the TIM to be updated, setting PS enabled will send NDP
that will signal that the station is sleeping. Sending PS-Poll to enable
power save is not correct, according to the following standard
statement: "A PS-Poll frame exchange does not necessarily result in an
Ack frame from the AP, so a non-AP STA cannot change power management
mode using a PS-Poll frame."
Signed-off-by: Adiel Aloni <adiel.aloni@intel.com>
This does not really work with mac80211_hwsim due to missing offload
support, but at least some minimal extra code coverage can be achieved.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
This makes it a bit clearer to see which parameters need to be modified
if the test vector needs to be recreated based on new values.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Verify that PMF can be marked required OWE networks and verify that a
station in transition mode can connect to an open network.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Verify that unexpected 2048-bit RSA client certificate gets rejected by
the RADIUS server if the server is configured to use Suite B at 192-bit
level.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Verify that unexpected p256 client certificate gets rejected if the
server is configured to use Suite B at 192-bit level.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
PMF is supposed to be enabled automatically in sigma_dut, so remove
the explicit argument to do so from the commands.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
All SAE and OWE associations are expected to require PMF to be
negotiated, so enable or require PMF in AP and STA configurations
accordingly to match the new sigma_dut behavior.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
GnuTLS seems to require the intermediate CA certificate to be included
both in the ca_cert and client_cert file for the cases of server and
client certificates using different intermediate CA certificates. Use
the user_and_ica.pem file with GnuTLS builds and reorder the
certificates in that file to make this work with GnuTLS.
Signed-off-by: Jouni Malinen <j@w1.fi>
Check for unexpected connection to avoid timeout on TLS alert event if
the implementation does not check DH key size at all.
Signed-off-by: Jouni Malinen <j@w1.fi>
Need to ignore missing RX-ANQP event for the FILS Realm Info if
wpa_supplicant build does not include FILS support.
Signed-off-by: Jouni Malinen <j@w1.fi>
Commit b488a12948 ('Clear PMK length and
check for this when deriving PTK') started rejecting PTK derivation
based on PMK length. This reduced coverage from the eapol-fuzzer, so set
the default length when initializing the state machine in the fuzzer to
reach the previously used code paths.
Signed-off-by: Jouni Malinen <j@w1.fi>
Wait for test/allocation failure for longer than the wait_fail_trigger()
default two seconds to allow DPP (in particular, PKEX) retransmission to
occur. This removes some issues where the previous wait was more or less
exactly the same duration as the retransmission interval and the first
Listen operation not always starting quickly enough to receive the first
frame.
Signed-off-by: Jouni Malinen <j@w1.fi>
When executing ./start.sh with OpenSSL 1.1.0f, an OCSP operation fails.
Put "-sha256" ahead of "-serial" to fix this.
~# openssl version
OpenSSL 1.1.0f 25 May 2017
~# openssl ocsp -reqout /lkp/benchmarks/hwsim/tests/hwsim/logs/current/ocsp-req.der -issuer /lkp/benchmarks/hwsim/tests/hwsim/auth_serv/ca.pem -serial 0xD8D3E3A6CBE3CD12 -no_nonce -sha256
ocsp: Digest must be before -cert or -serial
ocsp: Use -help for summary.
~# openssl ocsp -reqout /lkp/benchmarks/hwsim/tests/hwsim/logs/current/ocsp-req.der -issuer /lkp/benchmarks/hwsim/tests/hwsim/auth_serv/ca.pem -sha256 -serial 0xD8D3E3A6CBE3CD12 -no_nonce
Signed-off-by: leishaoting <leist.fnst@cn.fujitsu.com>
src/crypto/libcrypto.a and src/tls/libtls.a have circular references
and will need special handling with the linker at least for the time
being. This could be cleaned up eventually, but for now, provide a
mechanism to get the program linked.
This was already done in tests/Makefile, but tests/eapol-fuzzer/Makefile
needs the same.
Signed-off-by: Jouni Malinen <j@w1.fi>
Do not include this argument in normal case, but add a test case to
cover the special extra check case.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This test case is not really realistic and the second connection attempt
would fail if additional AES-based ciphers get provisioned. Work this
around by dropping to CCMP only if other ciphers are present.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This is needed to avoid false errors with GCMP-256 and CCMP-256 to be
added in the implementation.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
The kernel started enforcing attribute lengths, and nl80211.py had been
doing it all wrong - the padding must be present, but not part of the
length.
Fix it to do it the right way.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
These test cases were failing when run immediately after
dpp_pkex_test_fail. It looks like timing of the TX status and the short
eloop wait were getting reordered in this cases. This ended up with some
of the DPP-TX-STATUS event messages missing. Instead of explicitly
checking for those message, simply count the number of DPP-TX messages
to verify that the correct number of retries are being sent.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Fix problem when running ap_ft test cases with real HW using remote
tests and hwsim wrapper by using the newer hostapd.app_ap() API.
Signed-off-by: Janusz Dziedzic <janusz.dziedzic@gmail.com>
These VHT160 with DFS cases were in a single test case to optimize test
execution time with parallel wait for the 60 second CAC. However, this
design has become difficult to support with the kernel changes that
allow radar events to be shared between interfaces. To avoid need for
more workarounds here just for testing purposes, split this into two
test cases so that conflicting events from another interface do not
cause the test case to fail.
Signed-off-by: Jouni Malinen <j@w1.fi>
These DFS radar detection cases were in a single test case to optimize
test execution time with parallel wait for the 60 second CAC. However,
this design has become difficult to support with the kernel changes that
allow radar events to be shared between interfaces. To avoid need for
more workarounds here just for testing purposes, split this into two
test cases so that conflicting events from another interface do not
cause the test case to fail.
Signed-off-by: Jouni Malinen <j@w1.fi>
mac80211_hwsim module typically dumps a lot of details into the kernel
message buffer. While it's probably okay in a dedicated VM, it's way too
chatty in other setups.
The kernel allows fine-tuning logging via the dynamic debugging
facility. Let's enable all logging locations in the mac80211_hwsim
module so that we don't loose debugging output when the kernel adopts
the dynamic debug mechanism for the driver.
Signed-off-by: Lubomir Rintel <lkundrak@v3.sk>
hostapd implementation was changed to use a valid Status Code when
rejecting the connection. This test case was forgotten at the time, but
it needs a matching change to allow the new value (1 instead of 14).
Signed-off-by: Jouni Malinen <j@w1.fi>
This allows mesh_sae_groups_invalid and
wpas_mesh_secure_sae_group_negotiation to be run with BoringSSL (group
25 not available anymore).
Signed-off-by: Jouni Malinen <j@w1.fi>
Use absolute path name for configuration file to ensure the file can be
succesfully reloaded and read on SIGHUP signal. This is needed when
running the test case on host (i.e., not using a VM).
Signed-off-by: Sriram R <srirrama@qti.qualcomm.com>
Change the test condition from "is OpenSSL 1.0.2" to "is not OpenSSL
1.0.1", so that the TLSv1.2 test step gets executed with OpenSSL 1.0.2
and 1.1 (and newer).
Signed-off-by: Jouni Malinen <j@w1.fi>
Recent versions of tshark/wireshark renamed these fields, deal
with that in the tshark wrapper code.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Beacon more frequently since Probe Request frames are practically ignored
in this test setup (ext_mgmt_frame_handled=1 on hostapd side) and
wpa_supplicant scans may end up getting ignored if no new results are
available due to the missing Probe Response frames.
Signed-off-by: Jouni Malinen <j@w1.fi>
I find myself writing a version of this script every now and
then, but there's little point in that - just add one to the
tree so we can use it again.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The extra sanity check for replay protection in these procedures ended
up breaking the tests. RESET_PN cannot be used before RESEND_* commands
since that would prevent the DUT from accepting the retransmitted
EAPOL-Key frames.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This describes how various wpa_supplicant/hostapd extensions can be used
to test IEEE 802.11 functionality in other devices.
Signed-off-by: Jouni Malinen <j@w1.fi>
These test cases do not really verify any specific DUT behavior
automatically, i.e., these are here to generate sniffer captures for
manual analysis.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
The previous designed worked since wpa_supplicant did not track pending
request state. With such tracking added, this test case needs to make
sure there is a pending operation when injecting the invalid response.
Signed-off-by: Jouni Malinen <j@w1.fi>
The previous versions expired, so need to re-sign these to fix number of
the EAP test cases. In addition, add a shell script (update.sh) and the
needed CA files to automate this full update process.
Signed-off-by: Jouni Malinen <j@w1.fi>
The new wpa_supplicant network parameter group_mgmt can be used to
specify which group management ciphers (AES-128-CMAC, BIP-GMAC-128,
BIP-GMAC-256, BIP-CMAC-256) are allowed for the network. If not
specified, the current behavior is maintained (i.e., follow what the AP
advertises). The parameter can list multiple space separate ciphers.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
There was a race condition on the sequence where iface.AbortScan() is
immediately followed by iface.Scan(). If the driver event
(NL80211_CMD_SCAN_ABORTED) arrived after the following new scan request,
the D-Bus operation failed. This is not what this test case is trying to
check, so wait for an indication of the previous scan having terminated
properly before issuing the next scan.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
The STA can get disconnected event before the AP processed the
deauthentication frame, resulting in GET_FAIL command being sent too
early. Fix this by waiting for AP-STA-DISCONNECTED on AP side, too.
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
Import vht_supported from test_ap_vht to fix the following issue:
rrm_beacon_req_table_vht run failed: global name 'vht_supported' is not defined
Signed-off-by: Li Zhijian <lizhijian@cn.fujitsu.com>
This makes it easier to post-process frame capture files if frames need
to be decrypted in test cases that do not configure wlantest with the
PMK directly (i.e., mainly the cases when a RADIUS server is used).
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Wait for the configuration step to complete before forcefully
terminating DPP listen. Previous version was causing failures for this
test case sequence:
dpp_qr_code_auth_initiator_enrollee dpp_pkex_config2
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
On slow machines or inside VM it may take some time for "DISCONNECTED"
event to arrive. Since the retry delay counter is started already, it
may result in less than 5 seconds time between "DISCONNECTED" and
"CONNECTED" events.
Fix the test by taking more accurate timestamps between the events.
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
Previously p2p_channel_drv_pref_* tests would fail
if dedicated P2P device is used, since the SET commands
were sent to incorrect interface.
Fix this by using a global control interface instead.
Signed-off-by: Adiel Aloni <adiel.aloni@intel.com>
We capture the dmesg that contains everything, but if a test
causes a kernel crash we will miss all logging at higher levels
like debug. Change the printk level to catch all of that too.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Lockdep no longer prints "INFO:" but now prints "WARNING:".
Also add the "*** DEADLOCK ***" string it usually prints so
if it changes again we can keep finding that string.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
