Replace driver wrapper calls to hostapd_tx_status(),
hostapd_rx_from_unknown_sta(), hostapd_mgmt_rx(), and
hostapd_mgmt_tx_cb() with new generic driver events
EVENT_TX_STATUS, EVENT_RX_FROM_UNKNOWN, and EVENT_RX_MGMT.
This cleans up lot of the driver wrapper code to be less dependent
on whether it is being used within wpa_supplicant AP mode or hostapd.
This remove the need from driver_test.c to go through internal hostapd
structures to find the appropriate BSS when reporting events on secondary
BSSes.
The separate header file is not needed since none of the driver wrappers
include it anymore. Move the WLAN_STA_* definitions back to be together
with struct sta_info definition.
This removes need for including hostapd/sta_flags.h into driver
wrappers and removes any remaining dependencies between driver flags
and internal hostapd flags.
The WMM STA flag is already taken care of by handle_assoc_cb() and there
is no point trying to do this unless hostapd is taking care MLME
processing, so no need to call this from drv_callbacks.c.
The Prism54.org project seems have been dead for a while and it does not
look like this driver would ever be maintained again. Furthermore, it is
difficult to find a version that would work with the driver_prism54.c
wrapper and there is another driver for these card in the Linux kernel
tree.
The hostapd integration in driver_prism54.c is quite different from the
other driver wrappers and would require major effort to get it cleaned
up. Since there does not seem to be any real users for the cleaned up
version, there does not seem to be justification to spend this effort on
the wrapper. This old code is making it much more difficult to clean up
the driver interface and at this point, the best option seems to be to
remove the driver wrappers. Should someone really still need this, the
old code will continue to be available in hostapd 0.6.x.
Instead of using the latest selected registrar change, collect selected
registrar information separately from all registrars and use the union
of this information when building the WPS IE for Beacon and Probe
Response frames.
Note: SetSelectedRegistrar UPnP action does not include a unique
identifier, so the ER matching routine is based only on the IP address
of the ER. In theory, there could be multiple ERs using the same IP
address (but different port or URL), so there may be some corner cases
that would not always match the correct ER entry at the AP. Anyway, this
is not really expected to occur in normal use cases and even if it did
happen, the selected registrar information is not any worse than it was
before when only the last change from any registrar for being
advertized.
These callbacks can be handled internally within core WPS code, so there
is no need to go through wps_hostapd.c with a callback function that is
just calling back into the core WPS code.
This can be handled internally within core WPS code, so there is no
need to go through wps_hostapd.c with a callback function that is just
calling back into the core WPS code.
IEEE 802.11w uses distinct key indexes (4 and 5) so the same
get_seqnum() handler can be used to fetch packet number for both
TKIP/CCMP and BIP(using IGTK).
Since the new get_seqnum_igtk() handler was not actually implemented by
any driver wrapper, this may also fix BIP/IGTK sequence number reporting
with driver_nl80211.c.
There was code for configuring this, but no driver wrapper actually
implements the actual setting. Remove this for now to reduce potential
confusion and to simply the driver interface.
In addition to the bitrate, the only other variable in this structure
is used internally in hostapd. Move this structure into hostapd.h and
make the driver API use simpler data structure (array of bitrates).
if_add/if_remove can now be used as the generic driver ops for adding
and removing virtual interfaces of various types. In addition,
driver_nl80211.c is now including this code unconditionally, so that
the functions are not limited only for hostapd.
This is a separate program and is used mainly with hostapd, so it is
better to move this into the hostapd subdirectory now that Milenage
code has already been moved into src/crypto. Milenage was the only
generic component in hlr_auc_gw.
This is an initial step in further cleaning up the EAPOL authenticator
use to avoid requiring direct accesses to the internal data structures.
For now, number of external files are still including the internal
definitions from eapol_auth_sm_i.h, but eventually, these direct
references should be removed.
In addition, start ordering header file includes to be in more
consistent order: system header files, src/utils, src/*, same
directory as the *.c file.
This removes the hardcoded definition from Makefile and cleans up
source code by moving the mail HOSTAPD_DUMP_STATE blocks into separate
files to avoid conditional compilation within files.
While this may not include knowledge of all EAP methods since this
depends on build configuration, it is better to not have to include
ieee802_1x.h into eapol_sm.c.
Instead of getting this via hostapd.h, include it as the first
non-system header file in all source code files in the same way as
used in all other files.
This makes it clearer which files are including header from src/common.
Some of these cases should probably be cleaned up in the future not to
do that.
In addition, src/common/nl80211_copy.h and wireless_copy.h were moved
into src/drivers since they are only used by driver wrappers and do not
need to live in src/common.
Instead of using hardcoded maximum A-MPDU length of 64 kB and no
restrictions on minimum MPDU Start Spacing, use the correct values
reported by the driver.
Use shared functions for converting Primary Device Type between binary
and string formats. In addition, use array of eight octets instead of a
specific structure with multiple fields to reduce code complexity.
This gets rid of previously deprecated driver_ops handlers set_wpa,
set_drop_unencrypted, set_auth_alg, set_mode. The same functionality
can be achieved by using the init/deinit/associate handlers.
This moves the MTU definition into driver_hostap.c since it was really
meant to be specific to this driver. Since this was the last remaining
definition in hostapd_defs.h, remove that header file as unnecessary.
Clean up driver interface by merging hostapd and wpa_supplicant
specific set_beacon driver_ops into a single one. In addition,
merge set_beacon_int into to the same operation.
This removes following WFA WLANConfig Service actions and the related
state variables: GetAPSettings, SetAPSettings, DelAPSettings,
GetSTASettings, SetSTASettings, DelSTASettings, RebootAP,
ResetAP, RebootSTA, ResetSTA.
While WFA WLANConfig Service version 1.0 claims that some of these are
mandatory to implement for an AP, there are no known implementations
supporting these actions neither in an AP/proxy or an External Registrar
that would use them. These are unlikely to be supported in the future
either and as such, it is just simpler to get rid of them to clean up
the implementation and reduce code size.
When using drivers that process management frames internally (e.g.,
madwifi, atheros, bsd), the driver may accept association with IEs
that do not match the security policy. Instead of silently leaving
the station associated, explicitly disassociate it to clear the
driver entry immediately.
There is no point in comparing cred->key == NULL since cred->key is
an array (never NULL). key_len == 0 should be used instead to indicate
that no key was specified.
Clean up code so that UPnP implementation does not need to include all
the HTTP functionality. In addition, make it easier to share HTTP server
functionality with other components in the future.
Instead of implementing HTTP client functionality inside
wps_upnp_event.c, use a generic HTTP client module to do this. The HTTP
client code can now be shared more easily for other purposes, too.
This functionality fits better with src/tls (i.e., internal TLS
implementation), so move it there to make crypto_internal.c more
of a wrapper like other crypto_*.c files.
The hostapd/wpa_supplicant compilation failed with CONFIG_IEEE80211R=y
or CONFIG_IEEE80211W=y option if CONFIG_EAP_PSK and CONFIG_EAP_GPSK are
not used.
Reorganize the TLS/crypto library segments into a single set of blocks
for each library instead of multiple locations handling library-specific
operations. Group crypto functionality together and get wpa_supplicant
and hostapd Makefile closer to eachother in order to make it easier to
eventually move this into a shared makefile.
Crypto library wrappers can now override the internal DH (group 5)
implementation. As a starting point, this is done with OpenSSL. The
new mechanism is currently available only for WPS (i.e., IKEv2 still
depends on the internal DH implementation).
When checking the validity of VLAN ID based on RADIUS-based ACL or
accept_mac_file, the assigned vlan_id, not the old sta->vlan_id
(likely zero) needs to be used.
hostapd needs to remove the old STA entry if it exists when processing
reassociation back to the same AP. This removes the potentially PS
buffered frames and allows association parameters to be updated with
mac80211.
Store a copy of device attributes during WPS protocol run and make it
available for external programs via the control interface STA MIB
command for associated stations. This gives access to device name and
type which can be useful when showing user information about associated
stations.
The group key state machine needs to be re-initialized with possible
updated GTK length when restarting WPA (e.g., when WPS was used to
reconfigure the AP).
This is not really of that much use since rc4_skip() can be used as
easily. In addition, rc4 has caused some symbol conflicts in the past,
so it is easier to live without that as an exported symbol.
This is a (hopefully) temporary workaround to allow the same source code
tree to be used for building hostapd and wpa_supplicant without having
to manually force recompilation of some files. Currently, some of the
driver wrapper files need to be built separately for hostapd and
wpa_supplicant (#ifdef's in the files based on AP functionality).
This is somewhat racy as far as parallel make execution is concerned,
i.e., it may be necessary to run "make -j#" twice (plain "make" works
fine. Since this is supposed to be a temporary workaround, there is not
much point in trying to fix this with any more complex make processing.
Instead of having all driver stuff collected across wpa_supplicant
and hostapd, create a common snippet that they both include and
that handles the build configuration.
Instead of calling specific Probe Request handler functions, use a
generic mechanism that allows multiple callback functions to be
registered for getting notification on receive Probe Request frames.
The driver wrappers should not need to include wps_hostapd.h, so let's
make this easier by introducing a driver callback for reporting Probe
Request frames.
Previously, we would have allowed both the WPA and RSN EAPOL-Key
types to be used regardless of whether the association is using
WPA or RSN/WPA2. This shouldn't result in any significant problems
on the Authenticator side, but anyway, we should check the type and
ignore the EAPOL-Key frames that used unexpected type.
hostapd_cli wps_pin command can now have an optional timeout
parameter that sets the PIN lifetime in seconds. This can be used
to reduce the likelihood of someone else using the PIN should an
active PIN be left in the Registrar.
We could use auto-channel selection here eventually, but for now,
reject the configuration since it is not going to work correctly
(Beacon and Probe Response frames use incorrect value in DS Params).
Port the code from wpa_supplicant to re-use an existing ctrl_iface
socket file if the file does not seem to be in use. This allows
hostapd to recover from unclean shutdown of the control interface.
None of the driver wrappers user this. hostapd-controlled broadcast SSID
hiding can only be used with drivers that use hostapd for handling
Beacon and Probe Request/Response frames.
None of the driver wrappers use this. Only the drivers that use hostapd
for Beacon and Probe Request/Response handling can now use IEEE 802.11d
properly.
This was not really supported by any of the included driver wrappers. If
this functionality is desired in the future, this (or something similar)
can be added with the changes needed into a driver wrapper to use the
mechanism.
This simplifies driver wrapper operations and removes last direct
struct hostapd_data dereferences from driver_nl80211.c. In addition,
some of the TX callbacks are now fixed for secondary BSSes.
