Commit graph

129 commits

Author SHA1 Message Date
Kyeyoon Park
ec8f36afca AP: Add support for BSS load element (STA Count, Channel Utilization)
The new "bss_load_update_period" parameter can be used to configure
hostapd to advertise its BSS Load element in Beacon and Probe Response
frames. This parameter is in the units of BUs (Beacon Units).

When enabled, the STA Count and the Channel Utilization value will be
updated periodically in the BSS Load element. The AAC is set to 0 sinze
explicit admission control is not supported. Channel Utilization is
calculated based on the channel survey information from the driver and
as such, requires a driver that supports providing that information for
the current operating channel.

Signed-off-by: Kyeyoon Park <kyeyoonp@qca.qualcomm.com>
2014-10-21 23:25:48 +03:00
Sunil Dutt
c53a9bf818 Check for driver's DFS offload capability before handling DFS
This fixes couple of code paths where the WPA_DRIVER_FLAGS_DFS_OFFLOAD
flag was not checked properly and unexpected DFS operations were
initiated (and failed) in case the driver handles all these steps.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2014-09-22 16:50:28 +03:00
Michal Kazior
6782b6846b hostapd: Move CSA parameters to hostapd_data
This prepares CSA structure and logic in hostapd for multi-BSS channel
switching.

Signed-hostap: Michal Kazior <michal.kazior@tieto.com>
2014-06-28 11:02:39 +03:00
Jouni Malinen
bc32bb70d7 Make a code path easier for static analyzers to understand
prev cannot be NULL here in the hostapd_eid_country_add() call since
prev is set whenever start becomes non-NULL. That seems to be a bit too
difficult for some static analyzers, so check the prev pointer
explicitly to avoid false warnings.

Signed-off-by: Jouni Malinen <j@w1.fi>
2014-06-07 15:37:31 +03:00
Darshan Paranji Sri
95b6bca66d Add rsn_pairwise bits to set_ieee8021x() driver_ops
This fixes an issue where a driver using the deprecated set_ieee8021x()
callback did not include rsn_pairwise bits in the driver configuration
even if mixed WPA+WPA2 configuration was used. This could result, e.g.,
in CCMP not being enabled properly when wpa_pairwise=TKIP and
rsn_pairwise=CCMP was used in the configuration. Fix this by using
bitwise OR of the wpa_pairwise and rsn_pairwise values to allow the
driver to enable all pairwise ciphers.

In addition, make the newer set_ap() driver_ops use the same bitwise OR
design instead of picking between rsn_pairwise and wpa_pairwise. This
makes the code paths consistent and can also fix issues with mixed mode
configuration with set_ap().

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2014-06-03 13:59:22 +03:00
Jouni Malinen
06df2aa60a Remove floating constant suffix 'd' from test coee
clang scan-build does not seem to like the 'd' suffix on floating
constants and ends up reporting analyzer failures. Since this suffix
does not seem to be needed, get rid of it to clear such warnings.

Signed-off-by: Jouni Malinen <j@w1.fi>
2014-04-29 12:52:10 +03:00
Peng Xu
196c9c7cd2 Make channel parameters available in set_ap() driver operation
This provides information to allow the driver to be configured for
updated channel parameters, e.g., when dynamically changing HT20/HT40
bandwidth.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2014-04-29 12:16:51 +03:00
Maxime Bizon
2aa82e52da Interworking: Don't filter probe requests when interworking is disabled
With hidden SSID (ignore_broadcast_ssid), an IOS device trying to
connect to the AP will send a probe request with ANT == 2. If
interworking support is just compiled (not enabled), we will drop the
probe request since default ANT is 0.

Check that interworking is enabled before filtering based on ANT or
HESSID to match the behavior of code without CONFIG_INTERWORKING.

Signed-off-by: Maxime Bizon <mbizon@freebox.fr>
2014-04-24 12:15:32 +03:00
Jouni Malinen
a14896e8bb HS 2.0R2 AP: Add OSEN implementation
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
2014-02-26 01:24:24 +02:00
Chaitanya T K
3d7ad2f681 hostapd: Configure spectrum management capability
Add configuration of Spectrum Management subfield in the Capability
Information of Beacon, Probe Response, and Association Response frames.
Spectrum Management bit is set when directly requested by new
configuration option spectrum_mgmt_required=1 or when AP is running on
DFS channels. In the future, also TPC shall require this bit to be set.

Signed-hostap: Srinivasan <srinivasanb@posedge.com>
Signed-hostap: Chaitanya T K <chaitanyatk@posedge.com>
Signed-hostap: Marek Puzyniak <marek.puzyniak@tieto.com>
2014-02-25 00:54:59 +02:00
Srinivasan B
e0392f825d hostapd: Add Power Constraint element
Add Power Constraint information element to Beacon and Probe Response
frames when hostapd is configured on 5 GHz band and Country information
element is also added. According to IEEE Std 802.11-2012 a STA shall
determine a local maximum transmit power for the current channel based
on information derived from Country and Power Constraint elements.

In order to add Power Constraint element ieee80211d option need to be
enabled and new local_pwr_constraint config option need to be set to
unsigned value in units of decibels. For now this value is statically
configured but the future goal is to implement dynamic TPC algorithm
to control local power constraint.

Signed-hostap: Srinivasan <srinivasanb@posedge.com>
Signed-hostap: Chaitanya T K <chaitanyatk@posedge.com>
Signed-hostap: Marek Puzyniak <marek.puzyniak@tieto.com>
2014-02-24 23:51:23 +02:00
Jouni Malinen
b37d582eaf Replace ieee802_11_print_ssid() with wpa_ssid_txt()
There is no need to maintain two different functions for printing out
ASCII text version of SSID.

Signed-hostap: Jouni Malinen <j@w1.fi>
2014-02-04 13:23:35 +02:00
Jouni Malinen
5f9c134ab4 Remove obsolete license notifications
These files have been distributed only under the BSD license option
since February 2012. Clarify the license statements in the files to
match that to avoid confusion.

Signed-hostap: Jouni Malinen <j@w1.fi>
2013-12-24 22:59:52 +02:00
Jouni Malinen
bad5cdf491 Verify that beacon setup succeeds before proceeding
There is no point in starting the AP operations unless
the driver can be successfully configured to beacon.

Signed-hostap: Jouni Malinen <j@w1.fi>
2013-12-24 22:46:20 +02:00
Andrei Otcheretianski
76aab0305c Add secondary channel IE for CSA
If secondary channel is provided for CSA, advertise it in the Secondary
Channel Offset element in Beacon and Probe Response frames.

Signed-hostap: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
2013-12-24 08:27:28 +02:00
Andrei Otcheretianski
8f4713c5c9 Store entire CS freq_params and not only freq
When CSA flow starts, store the entire struct hostapd_freq_params and
not only CS frequency as it was before. The additional freq_params are
required to advertise CS supplementary IEs such as secondary channel,
wide bandwidth CS, etc.

Signed-hostap: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
2013-12-24 08:23:40 +02:00
Andrei Otcheretianski
13daed58c7 Include driver.h in hostapd.h
This allows use of structs (and not only pointers) defined in drivers.h.
Remove also some not needed forward declarations and redundant includes.

Signed-hostap: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
2013-12-24 08:22:37 +02:00
Marek Kwaczynski
77a3e796e1 hostapd: Fix set beacon in multiple BSSID scenario
Check if the BSS interface has started before setting beacon.
Lack of this condition can cause segmantation fault.

Signed-hostap: Marek Kwaczynski <marek.kwaczynski@tieto.com>
2013-11-22 18:02:56 +02:00
Andrei Otcheretianski
bf281c129f Add AP channel switch mechanism
Build CSA settings and call the driver to perform the switch. Construct
Beacon, Probe Response, and (Re)Association Response frames both for CSA
period and for the new channel. These frames are built based on the
current configuration. Add CSA IE in Beacon and Probe Response frames.

Signed-hostap: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
2013-11-17 17:12:58 +02:00
Andrei Otcheretianski
e44a384b68 Move AP parameter filling into a helper function
Signed-hostap: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
2013-11-17 17:12:58 +02:00
Jouni Malinen
61323e70e1 Convert perror/printf calls to wpa_printf
This makes debug and error logging more consistent and allows them to be
directed to a file more easily.

Signed-hostap: Jouni Malinen <j@w1.fi>
2013-11-02 12:58:33 +02:00
Jouni Malinen
9bc33868bf Add test option for specifying hardcoded BSS Load element
The new bss_load_test parameter can be used to configure hostapd to
advertise a fixed BSS Load element in Beacon and Probe Response frames
for testing purposes. This functionality is disabled in the build by
default and can be enabled with CONFIG_TESTING_OPTIONS=y.

Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
2013-10-18 14:13:45 +03:00
Jouni Malinen
85b4eac364 P2P: Do not reply to 802.11b-only Probe Request frames as GO
If AP mode SME/MLME within wpa_supplicant is used for processing Probe
Request frames in GO mode, drop Probe Request frames that include only
802.11b rates per P2P spec section 2.4.1.

Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
2013-06-19 19:16:23 +03:00
Johannes Berg
c2aff6b1d1 hostapd: Add some testing options
In order to test clients in scenarios where APs may (randomly)
drop certain management frames, introduce some testing options
into the hostapd configuration that can make it ignore certain
frames. For now, these are probe requests, authentication and
(re)association frames.

Signed-hostap: Johannes Berg <johannes.berg@intel.com>
2013-04-23 17:51:28 +03:00
Jouni Malinen
0a66ce3c49 WNM: Add support for SSID List element matching
This allows Probe Request frame processing to compare the configured
SSID to the SSID List element in addition to the SSID element.

Signed-hostap: Jouni Malinen <j@w1.fi>
2012-12-16 21:22:24 +02:00
Arik Nemtsov
4425645113 AP: Configure basic rates from iface and not conf
The conf doesn't contain any basic rates in some cases. Most notably,
when starting a P2P GO in 5 GHz. Use the iface rates which are
initialized in hostapd_prepare_rates() to the conf rates or set to
default values if no conf values exist. This fixes a bug introduced in
commit e5693c4775.

Signed-hostap: Arik Nemtsov <arik@wizery.com>
2012-09-07 00:22:40 +03:00
Jouni Malinen
b52f084cfa Add parameter for vendor specific elements into Beacon/Probe Response
The new vendor_elements parameter in hostapd.conf can be used to add new
vendor specific element(s) into Beacon and Probe Response frames.

Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
2012-08-27 16:20:10 +03:00
Jouni Malinen
986de33d5c Convert remaining SSID routines from char* to u8*
This makes it more explicit that the SSID is not a null terminated
C string.

Signed-hostap: Jouni Malinen <j@w1.fi>
2012-08-07 16:07:25 +03:00
Jouni Malinen
8342185012 HS 2.0: Add mechanism for disabling DGAF
disable_dgaf=1 in hostapd.conf can now be used to disable downstream
group-addressed forwarding (DGAF). In this configuration, a unique
GTK (and IGTK) is provided to each STA in the BSS to make sure the
keys do not match and no STA can forge group-addressed frames.

An additional mechanism in the AP needs to be provided to handle some
group-addressed frames, e.g., by converting DHCP packets to unicast
IEEE 802.11 frames regardless of their destination IP address and by
providing Proxy ARP functionality.

Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
2012-07-30 18:23:52 +03:00
Jay Katabathuni
19a8ad9944 HS 2.0: Add Hotspot 2.0 Indication for AP
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
2012-07-30 18:23:38 +03:00
Mahesh Palivela
532b16c7a9 hostapd: Add IEEE 802.11ac VHT IEs into Beacon/Probe Response
IEEE 802.11ac VHT changes to include VHT IEs in Beacon and Probe
Response frames.

Signed-hostap: Mahesh Palivela <maheshp@posedge.com>
2012-06-30 13:57:52 +03:00
Johannes Berg
baf513d695 Pass signal strength through, fix units
The signal strength is currently never used as the only driver reporting
it is nl80211 which uses IEEE80211_RADIOTAP_DB_ANTSIGNAL which is never
populated by the kernel. The kernel will (soon) populate
IEEE80211_RADIOTAP_DBM_ANTSIGNAL instead though, so use that.

Also, since it was never really populated, we can redefine the signal
field to be in dBm units only.

My next patch will also require knowing the signal strength of probe
requests throughout the code (where available), so add it to the
necessary APIs.

Signed-hostap: Johannes Berg <johannes.berg@intel.com>
2012-04-01 18:48:12 +03:00
Luciano Coelho
370b076197 hostapd: Only update already-set beacons when processing OLBC
When hostapd is about to start an AP using HT40, it starts a scan to
check whether it is allowed or not. If OLBC is detected before the
scan has completed, it sets the beacons prematurely.

To fix this, instead of setting all beacons when OLBC is detected,
only update the ones that have already been started.

Signed-off-by: Luciano Coelho <coelho@ti.com>
2012-04-01 18:12:04 +03:00
Vasanthakumar Thiagarajan
a0133ee1c9 nl80211: Make use of driver's capability to detect inactive stations
When drivers advertise their capability to free up inactive
stations based on ap_max_inactivity, send the inactivity period
timeout to driver in NL80211_ATTR_INACTIVITY_TIMEOUT. This
introduces a WPA_DRIVER_FLAGS (WPA_DRIVER_FLAGS_INACTIVITY_TIMER)
so that the inactivity period will be sent only when this capability
bit is set.

Signed-hostap: Vasanthakumar Thiagarajan <vthiagar@qca.qualcomm.com>
2012-03-27 20:49:44 +03:00
Jouni Malinen
8017b538e7 P2P: Use Device ID attribute to filter Probe Request frames as GO
The Device ID attribute was already used in Listen state, but it was
ignored in GO role. Verify that there is a match with Device ID in
GO rule, too, before replying to the Probe Request frame.

Signed-hostap: Jouni Malinen <j@w1.fi>
2012-01-08 09:35:33 -08:00
Arik Nemtsov
5b99e21a14 Set driver Probe Response template for AP mode offload
Configure a Probe Response template for drivers that support it. The
template is updated when the Beacon template is updated.

The Probe Response template is propagated to the driver via the set_ap()
callback.

Signed-hostap: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Arik Nemtsov <arik@wizery.com>
2011-12-10 21:11:32 +02:00
Arik Nemtsov
eacc6b2478 Split Probe Response generation into a separate function
This is needed for Probe Response template, so move the code into a
separate function that can be shared.

Signed-hostap: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Arik Nemtsov <arik@wizery.com>
2011-12-10 21:11:32 +02:00
Jouni Malinen
e5693c4775 Merge set_rate_sets() driver_ops into set_ap()
Signed-hostap: Jouni Malinen <j@w1.fi>
2011-12-03 12:16:03 +02:00
Helmut Schaa
9a898ee879 Avoid excessive probe response retries
Some client implementations only wait a few ms after sending a probe
request while scanning. Since probe responses are always sent at a low
rate this can eat quite some airtime and it might be impossible to get
the frame out before the client leaves the channel again. If the client
leaves before all probe reponses where acked this can cause the probe
reponse to be retried quite often consuming even more airtime.

Hence, add a new noack flag to the driver's send_mlme callback that
allows hostapd to request whether the driver should expect an ACK for
this frame or not.

Use the new noack-policy only for broadcast probe requests that contain
a wildcard SSID.

Signed-hostap: Helmut Schaa <helmut.schaa@googlemail.com>
2011-11-19 19:09:49 +02:00
Helmut Schaa
8cfa3527e1 Allow MLME frames to be sent without expecting an ACK (no retries)
In some situations it might be benefical to send a unicast frame without
the need for getting it ACKed (probe responses for example). In order to
achieve this add a new noack parameter to the drivers send_mlme callback
that can be used to advise the driver to not wait for an ACK for this
frame.

Signed-hostap: Helmut Schaa <helmut.schaa@googlemail.com>
2011-11-19 19:02:05 +02:00
Jouni Malinen
735f652237 Remove unconfigurable cts_protection_type
This was included in the AP configuration parameters, but there has
been no way to set it to anything else than the default automatic
mode. Remove this parameter and just hardcode ERP determination to
follow the automatic mode.
2011-10-29 11:24:53 +03:00
Jouni Malinen
122ba57936 Interworking: Filter Probe Request frames based on HESSID and ANT
Do not reply to Interworking-enabled Probe Request frames if they
request mismatching HESSID or ANT.
2011-10-21 12:43:53 +03:00
Jouni Malinen
16991cffd6 Interworking: Include Access Network Type in set_ap() driver_ops
This may be needed for drivers that process Probe Request frames
internally.
2011-10-21 12:12:36 +03:00
Jouni Malinen
39b97072b2 Add support for Time Advertisement
This adds preliminary support for IEEE 802.11v Time Advertisement
mechanism with UTC TSF offset.
2011-10-18 00:24:16 +03:00
Jouni Malinen
4b2a77aba2 Interworking: Add support for configuring Roaming Consortium List 2011-10-17 23:55:50 +03:00
Jouni Malinen
c7c178e15e Interworking: Add Advertisement Protocol element
For now, assume that ANQP will always be enabled with Interworking.
This may be made separately configurable in the future.
2011-10-17 23:19:52 +03:00
Jouni Malinen
8a33a63f58 Add Interworking configuration in set_ap() driver_ops
Drivers that implement SME/MLME may find it easier to use separated
information to configure Interworking related parameters.
2011-10-17 21:35:41 +03:00
Jouni Malinen
06c4d2472f Move Ext Capab and Interworking element construction into shared file
These needs to be available for drivers that implement SME/MLME.
2011-10-17 21:03:52 +03:00
Jouni Malinen
6c0575c322 Remove unused function argument 2011-10-17 20:10:07 +03:00
Jouni Malinen
31357268e5 Move AP BSS configuration parameters into set_ap()
Remove the separate driver_ops functions set_cts_protect(),
set_preamble(), set_short_slot_time(), and set_ht_params(). These
belong into same set of operations as set_ap(), so there is no need
to maintain separate functions that just make the driver wrapper
more complex.

Since these have only been used with driver_nl80211.c, the driver_ops
can be removed immediately instead of maintaining backwards
compatibility period with the old functions.
2011-10-17 19:31:33 +03:00
Jouni Malinen
fd13a54180 Deprecate set_intra_bss() driver_ops
The AP client isolation parameter is now available through set_ap().
driver_nl80211.c was the only driver wrapper using the set_intra_bss()
call in hostap.git, but some external trees may have used this. Once
those are cleared, the set_infra_bss() driver_ops can be removed
completely. The only remaining use case for it currently is in P2P
GO mode with wpa_supplicant.
2011-10-17 18:58:46 +03:00
Jouni Malinen
5ce0f8b31b Remove unused P2P device discovery hack from Beacon configuration
AP mode operations were used for P2P device discovery Listen state
only during early experiments. This has now been cleaned up and
ieee802_11_set_beacon() is not called for P2P device discovery.
As such, this hack to skip Beacon configuration can be removed.
2011-10-17 18:39:31 +03:00
Jouni Malinen
062390efd4 Start deprecating various AP mode driver_ops
The preferred way of configuring AP mode will be to use set_ap() instead
of number of separate operations hostapd has collected over the years.
2011-10-17 18:35:25 +03:00
Jouni Malinen
b83e3e93c8 IEEE 802.11u: Add configuration and advertisement for Interworking 2011-10-16 23:55:34 +03:00
Jouni Malinen
fb91db5639 Provide extra IEs for AP mode management frames with set_ap
Drivers that build Beacon, Probe Response, and (Re)Association
Response frames can use this information to and WPS and P2P IE
when needed.
2011-08-26 21:14:25 +03:00
Jouni Malinen
97a7a0b504 Add support for setting SSID hiding mode through set_ap() 2011-08-26 21:12:47 +03:00
Jouni Malinen
b11d1d6439 Add crypto parameters to set_ap() command separately
This helps drivers that build the Beacon and Probe Response frames
internally.
2011-08-26 21:11:42 +03:00
Jouni Malinen
ccb941e6da Add SSID as a separate item in AP mode Beacon setup
This makes it easier for drivers that need the SSID to get it from the
Beacon setup operation without having to parse the Beacon IEs.
2011-08-10 13:29:32 +03:00
Jouni Malinen
19c3b56685 Replace set_beacon() driver op with set_ap()
This change is a first step in better supporting different driver
architectures for AP mode operations with nl80211. This commit in
itself does not add new functionality, but it makes it easier to add
new AP mode parameters to address needs of drivers that have more of
the MLME/SME in firmware or kernel.
2011-08-10 13:22:37 +03:00
Jouni Malinen
bc45d4279f WPS: Do not update Beacon IEs before initial IE set
This avoids a request to the driver to first start beaconing before
the WPA/RSN IE has been generated and then immediately changing the
beacon IEs once the WPA/RSN IE is ready.
2011-08-09 14:40:06 +03:00
Jouni Malinen
04a85e4401 P2P: Filter Probe Request frames based on DA and BSSID in Listen state
Only accept Probe Request frames that have a Wildcard BSSID and a
destination address that matches with our P2P Device Address or is the
broadcast address per P2P specification 3.1.2.1.1.
2011-07-15 20:28:46 +03:00
Jouni Malinen
1161ff1ef5 hostapd: Allow TDLS use to be prohibited in the BSS
tdls_prohibit=1 and tdls_prohibit_chan_switch=1 and now be used to
disable use of TDLS or TDLS channel switching in the BSS using
extended cabilities IE as defined in IEEE 802.11z.
2011-01-28 19:21:59 +02:00
Jouni Malinen
cbcf92b42f AP: Validate management frame length
Make sure that received management frames are long enough before
processing them. This avoids a potential segmentation fault if a
driver delivers an invalid frame all the way to hostapd.
2011-01-17 12:21:29 +02:00
Jouni Malinen
0e8a96a911 Get rid of struct hostapd_driver_ops abstraction
This is not needed anymore and just makes things more difficult
to understand, so move the remaining function pointers to direct
function calls and get rid of the struct hostapd_driver_ops.
2010-11-24 16:50:06 +02:00
Jouni Malinen
3acdf771b8 hostapd_driver_ops reduction
send_eapol, set_key, read_sta_data, sta_clear_stats,
set_radius_acl_auth, set_radius_acl_expire, and set_beacon
to use inline functions instead of extra abstraction.
2010-11-24 16:34:49 +02:00
Jouni Malinen
cee7d66b1d hostapd: Start removing struct hostapd_driver_ops abstraction
Commit bf65bc638f started the path to
add this new abstraction for driver operations in AP mode to allow
wpa_supplicant to control AP mode operations. At that point, the
extra abstraction was needed, but it is not needed anymore since
hostapd and wpa_supplicant share the same struct wpa_driver_ops.

Start removing the unneeded abstraction by converting
send_mgmt_frame() to an inline function, hostapd_drv_send_mlme().
This is similar to the design that is used in wpa_supplicant and
that was used in hostapd in the past (hostapd_send_mgmt_frame()
inline function).
2010-11-24 15:19:50 +02:00
Jouni Malinen
dce044cce5 P2P: Extend P2P manager functionality to work with driver MLME
Add P2P IE into Beacon, Probe Response, and (Re)Association Request
frames for drivers that generate this frames internally.
2010-10-08 18:16:07 +03:00
Jouni Malinen
6c6915f3db P2P: Add defined values for P2P Manageability Bitmap 2010-09-09 07:17:20 -07:00
Jouni Malinen
962473c136 P2P: Add preliminary P2P Manager AP support for hostapd 2010-09-09 07:17:18 -07:00
Jouni Malinen
e44f8bf20a P2P: Add P2P configuration and callbacks in hostapd code 2010-09-09 07:17:17 -07:00
Jouni Malinen
a0fad21014 Indicate Barker Preamble Mode in ERP IE also based on local configuration
While this is not strictly speaking required based on dynamic
configuration (i.e., dot11ShortPreambleOptionImplemented is static
value based on implementation, not runtime configuration), it is better
to follow local configuration parameter for short preamble in addition
to the associated station capabilities.
2010-09-05 13:11:42 +03:00
Jouni Malinen
2d8bf73298 Add new debug message level for excessive information
Some frequent debug prints are of limited use and make debug output
difficult to read. Make them use a new debug level so that -dd
provides more readable output (-ddd can now be used to enable
the excessive debug prints).
2010-07-05 12:21:48 -07:00
Jouni Malinen
1bc774a12a hostapd: Reorder some IEs to get closer to IEEE 802.11 standard
Vendor-specific IEs are supposed to be in the end of the frame, so move
WMM into the end of Beacon, Probe Response, and (Re)Association Response
frames. In addition, move HT IEs to be later in (Re)Association
Response to match the correct order.

hostapd_eid_wpa() adds multiple IEs and the end result may not always be
correct. If WPA is enabled, WPA IE (vendor-specific) gets added in the
middle of the frame and not in the end. This would require a larger
change to spliut the IEs from WPA module into separate locations when
constructing Beacon and Probe Response frames. This is not yet addressed.
2010-05-02 10:53:01 +03:00
Jouni Malinen
8b897f5a17 Remove unnecessary ifname parameter from set_beacon()
The new per-BSS driver context makes this unnecessary.
2010-03-06 22:36:40 +02:00
Jouni Malinen
cd7d80f373 Allow Probe Request callbacks to terminate iteration 2009-12-28 13:14:58 +02:00
Jouni Malinen
1c08f8c0f0 Allocate Probe Response and Beacon buffers based on WPS IE length
This IE is of variable length and it is better to allocate the frame
buffer taking this length into account to prepare for future
additions.
2009-12-28 12:58:27 +02:00
Jouni Malinen
81f4f6195e Include header files explicitly in *.c, not via header files 2009-12-26 00:31:51 +02:00
Jouni Malinen
6226e38d00 Rename some src/ap files to avoid duplicate file names
Doxygen and some build tools may get a bit confused about same file
name being used in different directories. Clean this up a bit by
renaming some of the duplicated file names in src/ap.
2009-12-26 00:05:40 +02:00
Jouni Malinen
1057d78eb8 Move generic AP functionality implementation into src/ap
This code can be shared by both hostapd and wpa_supplicant and this
is an initial step in getting the generic code moved to be under the
src directories. Couple of generic files still remain under the
hostapd directory due to direct dependencies to files there. Once the
dependencies have been removed, they will also be moved to the src/ap
directory to allow wpa_supplicant to be built without requiring anything
from the hostapd directory.
2009-12-25 01:12:50 +02:00
Renamed from hostapd/beacon.c (Browse further)