The configuration parsing functions seemed to have worked fine before,
but these were real bugs even if they did not show up in practice.
hostapd_ip_diff() was broken for IPv6 addresses (overwrote address and
always returned 1.
This updated all doxygen runs to use the same style that was used for
wpa_supplicant full documents. The full vs. fast configurations are now
otherwise identical apart from fast not generating dot files or
latex/pdf version of the documentation.
Generate a SHA1 hash -based UUID from the local MAC address if the UUID
was not configured. This makes it easier to prepare for WPS since there
is no need to generate an UUID.
When using ap_scan=1, we know before the association request that MFP
will be supported, so we can as well require it. This helps mac80211 in
configuring whether to enable MFP.
IEEE 802.11w/D7.0 incorrectly changed the Action Category from 8 to 7
when renaming Ping to SA Query. Category 7 is reserved for HT (IEEE
802.11n) and IEEE 802.11w will need to continue to use the category 8
that was allocated for it.
mac80211 can now figure out which key to use for injected frames (in
most cases), so we can remove the workaround for configuring IGTK on the
monitor interface that is used for injecting frames.
Previous version assumed that the Flags field is always present and
ended up reading one octet past the end of the buffer should the Flags
field be missing. The message length would also be set incorrectly
(size_t)-1 or (size_t)-5, but it looks like reassembly code ended up
failing in malloc before actually using this huge length to read data.
RFC 2716 uses a somewhat unclear description on what exactly is included
in the TLS Ack message ("no data" can refer to either Data field in 4.1
or TLS Data field in 4.2), so in theory, it would be possible for some
implementations to not include Flags field. However,
EAP-{PEAP,TTLS,FAST} need the Flags field in Ack messages, too, for
indicating the used version.
The EAP peer code will now accept the no-Flags case as an Ack message if
EAP workarounds are enabled (which is the default behavior). If
workarounds are disabled, the message without Flags field will be
rejected.
[Bug 292]
There is not really much else the Authenticator can do if it does not
receive valid EAP response from the Supplicant/EAP peer. EAP-Failure
would need to be sent before trying to start again with
EAP-Request/Identity, but that is not allowed before the EAP peer
actually replies. Anyway, forcing a new association is likely to clean
up peer state, too, so it can help fixing some issues that could have
caused the peer not to be able to reply in the first place.
It looks like this never survived the move from IEEE 802.1X-2001 to
IEEE 802.1X-2004 and EAP state machine (RFC 4137). The retransmission
scheduling and control is now in EAP authenticator and the
calculateTimeout() producedure is used to determine timeout for
retransmission (either dynamic backoff or value from EAP method hint).
The recommended calculations based on SRTT and RTTVAR (RFC 2988) are not
yet implemented since there is no round-trip time measurement available
yet.
This should make EAP authentication much more robust in environments
where initial packets are lost for any reason. If the EAP method does
not provide a hint on timeout, default schedule of 3, 6, 12, 20, 20, 20,
... seconds will be used.
Previously, only the delivery option 1 from RFC 4284
(EAP-Request/Identity from the AP) was supported. Now option 3
(subsequent EAP-Request/Identity from RADIUS server) can also be used
when hostapd is used as a RADIUS server. The eap_user file will need to
have a Phase 1 user entry pointing to Identity method in order for this
to happen (e.g., "* Identity" in the end of the file). The identity hint
is configured in the same was as for AP/Authenticator case (eap_message
in hostapd.conf).
This commit changes just the name and Action category per D7.0. The
retransmit/timeout processing in the AP is not yet updated with the
changes in D7.0.
Some deployed WPS implementations fail to parse zero-length attributes.
As a workaround, send a null character if the device attribute string is
empty. This allows default values (empty strings) to be used without
interop issues.
Before this change, it looked like an AP that was using wsccmd did not
get activated since wsccmd left the Selected Registrar Config Methods
attribute to be zero. Since Device Password ID can be used to
distinguish PBC from any other method, use only it to figure out whether
PBC or PIN method is active.
It seems that for WPS registration we should use the same authentication
timeout as for ieee8021x, no? (See patch attached.) On slow platforms
public keys computation may take around 4-5 seconds (we actually stuck
on this issue).
Set ctrl_interface to non-empty value in INTERFACE_ADD to avoid
ctrl_iface.c assuming the control interface is not to be enabled. This
fixes the dynamically added interface to use control interface.
The NSIS installer will now add Windows registry entries for
wpa_supplicant during installation and removes them during
uninstallation. This allows wpa_gui to start wpasvc and add new
interfaces without requiring the user to do any manual registry
editing.
