Commit graph

15696 commits

Author SHA1 Message Date
Andrew Siplas
2dd72315d9 wpa_cli: Add missing quote around interface name
There was only an open quote present.

Signed-off-by: Andrew Siplas <andrew@asiplas.net>
2020-03-06 21:44:31 +02:00
Pravas Kumar Panda
f64b601c47 DFS: Add support for 80+80 MHz when going through channel switch
After a radar signal is detected, the AP should switch to another
channel, but in the case of 80+80 MHz, channel switch failed because
hostapd did not select the secondary channel in the process. Fix this by
selecting a secondary channel in the case of 80+80 MHz.

Signed-off-by: Xin Wang <xwangw@codeaurora.org>
Signed-off-by: Pravas Kumar Panda <kumarpan@codeaurora.org>
2020-03-06 21:44:31 +02:00
Jouni Malinen
72c34d23a4 tests: Automatic channel selection with fallback to 20 MHz
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
2020-03-06 21:44:31 +02:00
Jouni Malinen
2fb59e77b5 tests: HT with 20 MHz channel width doing CSA to 40 MHz
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
2020-03-06 21:44:31 +02:00
Jouni Malinen
154722e5b1 tests: Make ap_ht_40mhz_intolerant_ap more robust
Some test case sequences seemed to prevent the station from completing
the first OBSS scan (that scan was aborted) and that resulted in failing
the test case because the AP had not received any report in time. Wait
for scan completion and allow additional scans before timing out to
avoid indicating incorrect AP behavior in cases where the report was not
even received.

Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
2020-03-06 21:44:31 +02:00
Hu Wang
0a76a0b965 OWE: Fix PTK derivation workaround for interoperability
The initial implementation of the PTK derivation workaround for
interoperability with older OWE implementations forced
WPA_KEY_MGMT_PSK_SHA256 to be used for all of PTK derivation. While that
is needed for selecting which hash algorithm to use, this was also
changing the length of the PTK components and by doing so, did not
actually address the backwards compatibility issue.

Fix this by forcing SHA256 as the hash algorithm in PTK derivation
without changing the PTK length calculation for OWE when
owe_ptk_workaround is enabled.

Fixes: 65a44e849a ("OWE: PTK derivation workaround in AP mode")
Fixes: 8b138d2826 ("OWE: PTK derivation workaround in STA mode")
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
2020-03-06 21:44:31 +02:00
Jouni Malinen
b27c7ac0eb tests: wpa_supplicant SAVE_CONFIG without config file
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
2020-03-06 11:24:28 +02:00
Zhaoyang Liu
87775e32f6 Fix segmentation fault for NULL confname in SAVE_CONFIG
When wpa_supplicant interface is added without a configuration file, the
SAVE_CONFIG command causes a segmentation fault due to referencing a
NULL pointer if the update_config parameter is first explicitly enabled.

Fix the issue by checking the confname for NULL before saving
configuration.

Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
2020-03-06 11:21:58 +02:00
Alexander Wetzel
81621eab7c nl80211: Migrate from set_tx to key_flag API
Migrate nl80211 driver to key_flag API and add additional sanity checks.

I'm still not sure why we install unicast WEP keys also as default
unicast keys. Based on how I understand how mac80211 handles that it
should be pointless. I just stuck to how we do things prior to the patch
for WEP keys to not break anything. After all other drivers may need it.

Signed-off-by: Alexander Wetzel <alexander@wetzel-home.de>
2020-03-05 00:52:31 +02:00
Alexander Wetzel
9757f18db4 nl80211: Don't ignore when SET_KEY returns ENOENT
Always report an error when NL80211_CMD_SET_KEY can't set a key to
default.

The old ioctl-based design used a single command to add, set, and delete
a key and had to ignore ENOENT for key deletions. It looks like that
special handling was also ported for NL80211_CMD_NEW_KEY and
NL80211_CMD_SET_KEY instead only for NL80211_CMD_DEL_KEY.

Signed-off-by: Alexander Wetzel <alexander@wetzel-home.de>
2020-03-05 00:38:30 +02:00
Alexander Wetzel
98b8275d92 nl80211: Remove not needed netlink key attribute
Calling NL80211_CMD_NEW_KEY with NL80211_KEY_DEFAULT_TYPES attributes is
pointless. The information is not expected and therefore the kernel
never forwards it to the drivers. That attribute is used with
NL80211_CMD_SET_KEY.

Signed-off-by: Alexander Wetzel <alexander@wetzel-home.de>
2020-03-05 00:36:00 +02:00
Alexander Wetzel
8563f6f564 nl80211: Fix wrong return code in set_key error path
Allow to abort key installations with different error codes and fix one
misleading return code.

Signed-off-by: Alexander Wetzel <alexander@wetzel-home.de>
2020-03-05 00:28:50 +02:00
Alexander Wetzel
adf550ee4b nl80211: Ignore seq number for key deletion
Turns out we are sometime providing a seq when deleting the key. Since
that makes no sense on key deletion let's stop forwarding that to the
driver at least.

Signed-off-by: Alexander Wetzel <alexander@wetzel-home.de>
2020-03-05 00:27:48 +02:00
Alexander Wetzel
e9e69221c1 Validity checking function for key_flag API
Add masks for each key type to define which flags can be combined and
add a helper function to validate key_flag values.

Signed-off-by: Alexander Wetzel <alexander@wetzel-home.de>
2020-03-05 00:25:47 +02:00
Alexander Wetzel
5eb1632569 nl80211: Add a missing key_flag for WEP shared key authentication
Signed-off-by: Alexander Wetzel <alexander@wetzel-home.de>
2020-03-05 00:24:55 +02:00
Alexander Wetzel
82eaa3e688 Remove the not yet needed KEY_FLAG_MODIFY
I decided to drop KEY_FLAG_MODIFY instead of allowing flag combinations not
yet used in the code and will simply recreate it with the Extended Key
ID patches once we get there. For that reason I also did not renumber
the flags.

Signed-off-by: Alexander Wetzel <alexander@wetzel-home.de>
2020-03-05 00:17:23 +02:00
Alexander Wetzel
982b9cf029 Fix a wrong key_flag when deleting 802.1X WEP keys
Signed-off-by: Alexander Wetzel <alexander@wetzel-home.de>
2020-03-05 00:13:20 +02:00
Alexander Wetzel
d37c05e5b5 AP: Don't try to set NULL WEP default key
hostapd_broadcast_wep_set() can be called without a WEP key set.
Don't try to install a default key in that case.

This patch is not critical for the new API. With key_flag we just would
report an (ignored) error and do nothing. With the patch we simply do
nothing.

Signed-off-by: Alexander Wetzel <alexander@wetzel-home.de>
2020-03-05 00:03:56 +02:00
Alexander Wetzel
fa1a6aff22 Fix unicast argument for set_wep_key() from EAPOL supplicant
The unicast parameter in set_wep_key() is only expected to be set to 0
or 1. Without this patch we set unicast to 0x80 instead of 1. Since
unicast is used as boolean that is working fine but violates the
documented API.

Signed-off-by: Alexander Wetzel <alexander@wetzel-home.de>
2020-03-04 23:59:49 +02:00
Jouni Malinen
72fd30c4b9 tests: WPS PBC/PIN timeout on AP
Verify that AuthorizedMACs advertisement is removed when a PBC session
or a PIN times out.

Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
2020-03-04 23:28:45 +02:00
Jouni Malinen
11dab0f37f WPS: Remove expired PINs on Selected Registrar timeout
This clears the AuthorizedMACs advertisement immediately when the
Selected Registrar timeout is hit and no more active PINs are present.
Previously, the AuthorizedMACs advertisement could remain in place
indefinitely since expired PINs were removed only when actually trying
to find a PIN for a new WPS exchange.

Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
2020-03-04 23:26:02 +02:00
Jouni Malinen
dc054892a2 tests: sigma_dut special case for SAE Password Identifier with PWE looping
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
2020-03-04 21:23:43 +02:00
Jouni Malinen
8f89e57ab5 DFS: More debug prints on channel selection after radar detection
This makes it easier to understand what is happening when a new channel
needs to be selected based on a radar detection event.

Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
2020-03-03 18:58:08 +02:00
Jouni Malinen
9c244b542e tests: DFS channel bandwidth downgrade from VHT80 to VHT40
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
2020-03-03 18:58:08 +02:00
Seevalamuthu Mariappan
4b37d24285 hostapd: Fix to downgrade bandwidth in radar detection
Upon radar detection we used to search channels with the same bandwidth.
This way we might not find any other channels. If there are no channels
available with that bandwidth the AP service will be stopped. To avoid
this problem, also search a suitable channel by downgrading the
bandwidth. This scenario is applicable during CAC as well.

Signed-off-by: Seevalamuthu Mariappan <seevalam@codeaurora.org>
2020-03-03 18:37:16 +02:00
Seevalamuthu Mariappan
7242087d1c DFS: Do not process radar event while disabling an interface
In the normal case hostapd_disable_iface() and hostapd_enable_iface()
will be done while switching to another DFS channel upon radar
detection. In certain scenarios radar detected event can come while
hostapd_disable_iface() is in progress and iface->current_mode will be
NULL in that scenario. Previously, we did not check for this scenario
and proceeded with the radar detection logic which can trigger a
segmentation fault. To fix this, avoid proceeding the radar detection
event if iface->current_mode is NULL.

Signed-off-by: Seevalamuthu Mariappan <seevalam@codeaurora.org>
2020-03-03 17:10:31 +02:00
Jouni Malinen
744a2f9846 tests: Specific vs. wildcard SSID in Probe Request frame in BSSID-scan
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
2020-03-02 20:44:23 +02:00
Veerendranath Jakkam
5fdacce465 Allow wildcard SSID to be enforced for a specific BSSID scan
Specific BSSID scan was replacing wildcard SSID with the known SSID if
any BSS with the specified BSSID is available in the known BSSes list.

Add control interface support to force use of a wildcard SSID in a
specific BSSID scan by user with the new "wildcard_ssid=1" argument to
the SCAN command.

Signed-off-by: Veerendranath Jakkam <vjakkam@codeaurora.org>
2020-03-02 20:33:52 +02:00
Jouni Malinen
97de4a0f9b tests: Verify that HE gets fully enabled for mesh
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
2020-03-02 19:56:27 +02:00
Pradeep Kumar Chitrapu
43282f7329 mesh: Fix HE enablement on 5 GHz with VHT
Incorrect he_enabled parameter was being passed to
hostapd_set_freq_params() in mesh which caused HE to be not fully
enabled on the 5 GHz band. Fix this by setting freq->he_enabled instead
of vht_freq.he_enabled so that the hostapd_set_freq_params() uses the
correct he_enabled value (and then ends up copying this to
vht_freq.he_enabled in the success case).

Fixes: 6e711e7ab3 ("mesh: Do not enable HE on 5 GHz without VHT")
Signed-off-by: Pradeep Kumar Chitrapu <pradeepc@codeaurora.org>
2020-03-02 19:54:35 +02:00
Jouni Malinen
8b077a42e5 tests: wpa_supplicant config file writing with SAE
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
2020-03-02 11:51:38 +02:00
Sachin Shelke
21f835e640 SAE: Allow SAE-only network profile with sae_password to be written
The commit a34ca59e (SAE: Allow SAE password to be configured separately
(STA)) added sae_password configuration option. We should also consider
sae_password in the wpa_config_write() function which stores the valid
network block details to an external database.

Fixes: a34ca59e4d ("SAE: Allow SAE password to be configured separately (STA)")
Signed-off-by: Sachin Shelke <sachin.shelke@nxp.com>
Signed-off-by: Cathy Luo <xiaohua.luo@nxp.com>
Signed-off-by: Ganapathi Bhat <ganapathi.bhat@nxp.com>
2020-03-02 11:49:19 +02:00
Jouni Malinen
5bad300565 privsep: Mask out control port capability flag
There is no support for using the control port for sending out EAPOL
frames through privsep yet, so mask out this capability to fall back to
the l2_packet based design.

Signed-off-by: Jouni Malinen <j@w1.fi>
2020-03-01 21:31:07 +02:00
Alexander Wetzel
c1a6b1e47e privsep: Add key_flag to set_key()
Pass through the new key_flag to wpa_priv.

Signed-off-by: Alexander Wetzel <alexander@wetzel-home.de>
2020-03-01 21:11:07 +02:00
Jouni Malinen
852d370f65 Silence a compiler warning in no-WEP and no-EAP builds
wep_keys_set was not used in wpas_start_assoc_cb() without
IEEE8021X_EAPOL, so need to make this local variable conditional on
build options.

Signed-off-by: Jouni Malinen <j@w1.fi>
2020-03-01 20:57:14 +02:00
Jouni Malinen
d9aafb75f1 tests: SAE and PSK with multiple passwords/passphrases
Signed-off-by: Jouni Malinen <j@w1.fi>
2020-03-01 19:53:16 +02:00
Ilan Peer
101da59aa2 common: Add support for element defragmentation
Add support for element defragmentation as defined in IEEE
P802.11-REVmd/D3.0, 10.28.12 (Element defragmentation).

Signed-off-by: Ilan Peer <ilan.peer@intel.com>
2020-02-29 23:56:15 +02:00
Ilan Peer
e636bc855f WPA: Rename FILS wrapped data
IEEE P802.11az/D2.0 renamed the FILS Wrapped Data element,
removing the FILS prefix. Change the code accordingly.

Signed-off-by: Ilan Peer <ilan.peer@intel.com>
2020-02-29 23:30:55 +02:00
Ilan Peer
94773d40fa crypto: Add a function to get the ECDH prime length
crypto_ecdh_prime_len() can now be used to fetch the length (in octets)
of the prime used in ECDH.

Signed-off-by: Ilan Peer <ilan.peer@intel.com>
2020-02-29 23:26:26 +02:00
Ilan Peer
e8ae97aebe nl80211: Allow TX status for Authentication frames
To support PASN authentication flow, where Authentication frames are
sent by wpa_supplicant using the send_mlme() callback, modify the logic
to also send EVENT_TX_STATUS for Authentication frames.

Signed-off-by: Ilan Peer <ilan.peer@intel.com>
2020-02-29 23:18:28 +02:00
Ilan Peer
c4988e73c0 driver: Extend send_mlme() with wait option
PASN authentication can be performed while a station interface is
connected to an AP. To allow sending PASN frames while connected, extend
the send_mlme() driver callback to also allow a wait option. Update the
relevant drivers and wpa_supplicant accordingly.

hostapd calls for send_mlme() are left unchanged, since the wait option
is not required there.

Signed-off-by: Ilan Peer <ilan.peer@intel.com>
2020-02-29 23:03:20 +02:00
Andrei Otcheretianski
d046f2a9f9 nl80211: Register for SAE Authentication frames more strictly
If the driver requires external SAE authentication, it would result in
registration for all Authentication frames, so even non-SAE
Authentication frames might be forwarded to user space instead of being
handled internally. Fix this by using a more strict match pattern,
limiting the registration to the SAE authentication algorithm only.

Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
2020-02-29 22:55:55 +02:00
Brian Norris
7a9c367225 DBus: Add "sae" to interface key_mgmt capabilities
This will be present when the driver supports SAE and it's included in
the wpa_supplicant build.

Signed-off-by: Brian Norris <briannorris@chromium.org>
2020-02-29 18:01:23 +02:00
Jouni Malinen
200c7693c9 Make WEP functionality an optional build parameter
WEP should not be used for anything anymore. As a step towards removing
it completely, move all WEP related functionality to be within
CONFIG_WEP blocks. This will be included in builds only if CONFIG_WEP=y
is explicitly set in build configuration.

Signed-off-by: Jouni Malinen <j@w1.fi>
2020-02-29 17:45:25 +02:00
Jouni Malinen
bca44f4e4e WPS: Remove static-WEP-only workaround
WEP provisioning was removed from WPS v2, so this workaround
functionality has not been applicable. Remove it completely.

Signed-off-by: Jouni Malinen <j@w1.fi>
2020-02-29 16:56:44 +02:00
Jouni Malinen
886ee6775f tests: Automatic channel selection with hw_mode=any
Signed-off-by: Jouni Malinen <j@w1.fi>
2020-02-29 11:23:03 +02:00
Neo Jou
b7f1d4f4d6 ACS: Allow hw_mode=any to be used with internal ACS algorithm
This was already supported in the offload ACS case and this commit
completes support for this with the internal ACS algorithm.

Signed-off-by: Neo Jou <neojou@gmail.com>
2020-02-29 11:23:03 +02:00
Neo Jou
d07f1ade90 ACS: Determine mode when using hw_mode=any
Set iface->current_mode and iface->conf->hw_mode when completing ACS
based on the selected channel in the hw_mode=any case.

Signed-off-by: Neo Jou <neojou@gmail.com>
2020-02-29 11:23:03 +02:00
Neo Jou
c60362e6e8 ACS: Extend acs_find_ideal_chan() to support multiple modes
This is preparation for being able to support hw_mode=any to select the
best channel from any supported mode.

Signed-off-by: Neo Jou <neojou@gmail.com>
2020-02-29 11:23:03 +02:00
Neo Jou
141a8815e7 ACS: Extend acs_request_scan() to support multiple modes
Add suitable channel frequencies from all modes into the scan parameters
when a single mode is not specified for ACS. This is preparation for
being able to support hw_mode=any to select the best channel from any
supported mode.

Signed-off-by: Neo Jou <neojou@gmail.com>
2020-02-29 11:23:03 +02:00