Commit graph

348 commits

Author SHA1 Message Date
Jouni Malinen
2d9c99e37b Retry scan-for-connect if driver trigger fails
This restores some of the pre-radio work behavior for scanning by
retrying scan trigger if the driver rejects it (most likely returning
EBUSY in case of nl80211-drivers). Retry is indicated in the
CTRL-EVENT-SCAN-FAILED event with "retry=1".

For manual scans (e.g., triggered through "SCAN" control interface
command), no additional retries are performed. In other words, if upper
layers want to retry, they can do so based on the CTRL-EVENT-SCAN-FAILED
event.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2015-01-19 20:25:20 +02:00
Jouni Malinen
911942ee64 Add a test framework for various wpa_supplicant failure cases
For CONFIG_TESTING_OPTIONS=y builds, add a new test parameter than can
be used to trigger various error cases within wpa_supplicant operations
to make it easier to test error path processing. "SET test_failure
<val>" is used to set which operation fails. For now, 0 = no failures
and 1 = scan trigger fails with EBUSY. More operations can be added in
the future to extend coverage.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2015-01-19 19:34:00 +02:00
Jouni Malinen
a8826b1848 Interworking: Avoid busy loop in scan result mismatch corner cases
It was possible for interworking_find_network_match() to find a possible
BSS match in a case where more thorough checks in
wpa_supplicant_select_bss() reject network. This itself is fine, in
general, but when combined with wpa_supplicant_fast_associate()
optimization and auto_interworking=1, this resulted in a busy loop of up
to five seconds and a possible stack overflow due to recursion in that
loop.

Fix this by limiting the Interworking wpa_supplicant_fast_associate()
call to be used only once per scan iteration, so that new scan
operations can be completed before going through the scan results again.

Signed-off-by: Jouni Malinen <j@w1.fi>
2015-01-17 01:52:07 +02:00
Jouni Malinen
54fe48b9dc mesh: Use the shared function with IBSS to determine channel parameters
Automatically enable HT20, HT40+, HT40-, or VHT, based on driver
capabilities. This obsoletes the mesh_ht_mode network block parameter
that was previously used to configure HT parameters.

Signed-off-by: Jouni Malinen <j@w1.fi>
2015-01-10 17:35:53 +02:00
Jouni Malinen
6334330ed6 mesh: Use a separate variable to track whether HT is enabled
A network profile parameter should not be used to check whether the
currently operating mesh has HT enabled.

Signed-off-by: Jouni Malinen <j@w1.fi>
2015-01-10 17:35:53 +02:00
Ilan Peer
56c76fa592 scan: Add MAC address randomization in scan handling
1. Supported MAC address randomization for scan.
2. Supported MAC address randomization for scheduled scan.
2. Supported MAC address randomization for pno.
4. Add functions to set and clear the MAC address randomization
   state variables.

Signed-off-by: Ilan Peer <ilan.peer@intel.com>
2015-01-04 23:06:31 +02:00
Eliad Peller
8c42b36902 WMM AC: Reconfigure tspecs on reassociation to the same BSS
The specification requires the tspecs to be kept upon reassociation to
the same BSS. Save the last tspecs before such reassociation, and
reconfigure on the association notification.

Note that the current flow is not transparent to the user
(it is notified about deauth/reassoc and tspec removal/addition).

Signed-off-by: Eliad Peller <eliadx.peller@intel.com>
2015-01-04 18:41:00 +02:00
Jouni Malinen
d97a3c4885 SME: Optimize OBSS scanning
Include only the potentially affected channel range in OBSS scans to
reduce the amount of offchannel time needed for scanning when requested
by the AP.

Signed-off-by: Jouni Malinen <j@w1.fi>
2014-12-22 22:07:03 +02:00
Masashi Honma
5b78493f3b mesh: Add mesh interface creation command for mesh gate
The mesh gate is used to bridge (or route) between mesh network and
another network. For example, mesh gate acts as router between mesh
network and IEEE 802.11 BSS network.

This command makes a virtual mesh interface to be used for mesh gate.

This command expects to be used like this.

wpa_cli -i wlan0 MESH_INTERFACE_ADD ifname=mesh0
wpa_cli -i mesh0 add_network
wpa_cli -i mesh0 set_network 0 ssid '"commell_2X_mmm"'
wpa_cli -i mesh0 set_network 0 mode 5
wpa_cli -i mesh0 set_network 0 frequency 2412
wpa_cli -i mesh0 set_network 0 key_mgmt SAE
wpa_cli -i mesh0 set_network 0 psk '"01234567"'
wpa_cli -i mesh0 mesh_group_add 0
wpa_cli -i wlan0 mesh_group_remove mesh0

Signed-off-by: Masashi Honma <masashi.honma@gmail.com>
2014-12-14 23:27:43 +02:00
Jouni Malinen
568475b70b HS 2.0: Allow CANCEL_FETCH_OSU to stop at scan completion
There is no need to start the GAS/ANQP fetch if the FETCH_OSU operation
has already been canceled.

Signed-off-by: Jouni Malinen <j@w1.fi>
2014-12-14 02:28:03 +02:00
Jouni Malinen
e374522827 Do not start new radio work on scan completion during ext work
Externally triggered scan could result in a new radio work item getting
started even when external radio work was in progress. Delay such start
until the external work is completed.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2014-12-01 20:17:08 +02:00
Andrei Otcheretianski
70d1e72849 wpa_supplicant: Handle link measurement requests
Send link measurement response when a request is received. Advertise
only RCPI, computing it from the RSSI of the request. The TX power field
is left to be filled by the driver. All other fields are not published.

Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
2014-11-22 21:45:07 +02:00
Assaf Krauss
4c4b230527 wpa_supplicant: Add an option to specify SSID in neighbor report requests
Allow supplying an SSID for the SSID IE. If not supplied, no SSID IE is
sent, and the request implies the current SSID.

Signed-off-by: Assaf Krauss <assaf.krauss@intel.com>
2014-11-22 21:36:42 +02:00
Assaf Krauss
d89c0701db wpa_supplicant: Add support for Neighbor Report
Add the ability to send a Neighbor Report Request (part of
RRM). Requester is then notified once the report arrives.

Signed-off-by: Assaf Krauss <assaf.krauss@intel.com>
2014-11-22 21:23:14 +02:00
Assaf Krauss
b361d580ec SME: Add RRM support to association request
In case the AP we are associating with advertises support for RRM,
advertise our own RRM support in the (Re)Association Request frame. This
is done by adding an RRM Capabilities IE. The underlying driver is
expected to further add a Power Capabilities IE to the request, and set
the Radio Measurement flag in the Capability Info field. At this point
the RRM Capabilities IE advertises no measurement support.

Signed-off-by: Assaf Krauss <assaf.krauss@intel.com>
2014-11-22 21:13:45 +02:00
Assaf Krauss
f936b73c4f wpa_supplicant: Store driver's RRM capabilities
Store the RRM capability flags reported by the underlying driver.

Signed-off-by: Assaf Krauss <assaf.krauss@intel.com>
2014-11-22 21:07:56 +02:00
Jouni Malinen
e1117c1c01 WNM: Optimize BSS transition management scans
When the list of preferred transition candidates is received, use the
identified channels to optimize the following scan so that no time is
wasted on other channels.

Signed-off-by: Jouni Malinen <j@w1.fi>
2014-11-22 20:17:47 +02:00
Jouni Malinen
d0b9ab69f6 WNM: Move transition candidate list processing to normal scan
This makes it easier to optimize transition request processing.

Signed-off-by: Jouni Malinen <j@w1.fi>
2014-11-22 18:40:03 +02:00
Jouni Malinen
8c9af762f3 WNM: Calculate valid-until time for transition candidate list
This is of more use than the raw validity interval (number of beacon
intervals) that was recorded previously.

Signed-off-by: Jouni Malinen <j@w1.fi>
2014-11-22 18:06:27 +02:00
Moshe Benji
d1f880013a WMM AC: Handle TSPEC action frames
Add the TSPEC to the driver on successful TSPEC ADDTS response. Delete
the TSPEC when receiving DELTS action.

Signed-off-by: Moshe Benji <moshe.benji@intel.com>
Signed-off-by: Eliad Peller <eliad@wizery.com>
2014-11-16 21:07:08 +02:00
Eliad Peller
674f6c073f WMM AC: Add basic ADDTS/DELTS sending functions
Add basic implementation for ADDTS and DELTS sending
functions.

wpas_wmm_ac_addts() will send ADDTS request public action,
containing TSPEC (traffic stream specification) with
the given params.

wpas_wmm_ac_delts() will look for the saved tspec with
the given tid, and send DELTS public action for it.

(Handling of ADDTS response and actually configuring the admission
control params will be added in following patches.)

Signed-off-by: Moshe Benji <moshe.benji@intel.com>
Signed-off-by: Eliad Peller <eliad@wizery.com>
2014-11-16 21:03:56 +02:00
Moshe Benji
471cd6e10c WMM AC: Add add_tx_ts and del_tx_ts driver ops
Add add_tx_ts() and del_tx_ts() ops to notify the driver about
TSPEC add / delete.

Additionally, add wmm_ac_supported flag to indicate
whether the driver supports WMM AC.

Signed-off-by: Moshe Benji <moshe.benji@intel.com>
Signed-off-by: Eliad Peller <eliad@wizery.com>
2014-11-16 20:47:36 +02:00
Moshe Benji
a0413b1734 WMM AC: Parse WMM IE on association
Initialize WMM AC data structures upon successful association
with an AP that publishes WMM support, and deinitialize the data
structure when the association is no longer valid.

Signed-off-by: Moshe Benji <moshe.benji@intel.com>
Signed-off-by: Eliad Peller <eliadx.peller@intel.com>
2014-11-16 20:47:34 +02:00
Thomas Pedersen
0f950df029 mesh: Add mesh robust security network
This implementation provides:

- Mesh SAE authentication mechanism
- Key management (set/get PSK)
- Cryptographic key establishment
- Enhanced protection mechanisms for robust management frames

Signed-off-by: Javier Lopez <jlopex@gmail.com>
Signed-off-by: Javier Cardona <javier@cozybit.com>
Signed-off-by: Jason Mobarak <x@jason.mobarak.name>
Signed-off-by: Thomas Pedersen <thomas@noack.us>
2014-11-16 19:43:06 +02:00
Jouni Malinen
a7f5271d52 Update pending connect radio work BSS pointer on scan update
It is possible for scan result processing or BSS entry removal to occur
while there is a pending connect or sme-connect radio work with a
previously selected BSS entry. The BSS pointer was previously verified
to be valid, i.e., still point to a BSS entry, at the time the actual
connection operation is started. However, that BSS entry could have
changed to point to another BSS if the old BSS entry was either removed
or reallocated and a new BSS entry was added at the same location in
memory. This could result in the connection attempt failing to configure
parameters properly due to different BSS information (e.g., different
BSSID).

Fix this by updated the pending connect radio work data on BSS entry
updates similarly to how the last_scan_res array was updated. If the
selected BSS entry is removed, this will still result in a failed
connection, but reallocated BSS entry is now followed properly and used
when the connection work starts.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2014-10-28 00:43:58 +02:00
Tomasz Bursztyka
5aa839c80b wpa_supplicant: Parent interface should know about its dedicated P2P dev
This will be useful to hand-off P2P commands from the parent interface
to its dedicated P2P device if that one is present, in DBus interface.

Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
2014-10-27 17:15:09 +02:00
Ilan Peer
20beb96ff9 P2P: Save group common frequencies
Once a P2P GO interface is configured, save the group common
frequencies, as this can be useful later for channel selection
considerations during channel switch, etc.

Signed-off-by: Ilan Peer <ilan.peer@intel.com>
2014-10-26 01:24:13 +03:00
Jouni Malinen
1f94e4ee3e Add test functionality to simulate driver increased ROC duration
The extra_roc_dur parameter can now be used in CONFIG_TESTING_OPTIONS=y
builds to simulate driver behavior where the ROC duration gets increased
without user space request.

Signed-off-by: Jouni Malinen <j@w1.fi>
2014-10-25 21:46:38 +03:00
Thomas Pedersen
8319e3120d mesh: Add mesh mode routines
Add routines to (de)initialize mesh interface data structures and
join and leave mesh networks.

Signed-off-by: Javier Lopez <jlopex@gmail.com>
Signed-off-by: Javier Cardona <javier@cozybit.com>
Signed-off-by: Jason Mobarak <x@jason.mobarak.name>
Signed-off-by: Thomas Pedersen <thomas@noack.us>
2014-10-25 17:43:20 +03:00
Eliad Peller
04ee647d58 HT: Let the driver advertise its supported SMPS modes for AP mode
Add smps_modes field, and let the driver fill it with its supported SMPS
modes (static/dynamic). This will let us start an AP with specific SMPS
mode (e.g., dynamic) that will allow it to reduce its power usage.

Signed-off-by: Eliad Peller <eliad@wizery.com>
2014-10-24 01:25:29 +03:00
Jouni Malinen
7475d299ab P2P: Search all 2.4 GHz social channels regardless of disallow_freq
Commit 1595eb93ae ('P2P: Add support for
60 GHz social channel') had an unintended change to how P2P search scans
2.4 GHz social channels. Use of p2p_supported_freq() to filter the list
of social channels ended up using the disallow_freq setting to remove
social channels from the P2P search scans. This is not desired since
peers need to be found on any of the social channels even if those
channels have been disabled from P2P operating channel use. Restore the
previous behavior by included all the 2.4 GHz social channels in P2P
search scans if the driver indicated support for the 2.4 GHz band.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2014-10-22 20:02:48 +03:00
Jouni Malinen
4a6cc86272 Add data test functionality
It is now possible to run hwsim_test like data connectivity test through
wpa_supplicant/hostapd control interface if CONFIG_TESTING_OPTIONS=y is
used for the build. Test functionality is enabled/disabled at runtime
with "DATA_TEST_CONFIG <1/0>". The "DATA_TEST_TX <dst> <src> <tos>"
command can be used to request a test frame to be transmitted.
"DATA-TEST-RX <dst> <src>" event is generated when the test frame is
received.

Signed-off-by: Jouni Malinen <j@w1.fi>
2014-10-19 20:51:45 +03:00
Bob Copeland
24bd4e0be5 nl80211: Add driver flag to indicate mesh support
Convert the driver flags variable to u64 since there was no room for
more flags.

Signed-off-by: Javier Lopez <jlopex@gmail.com>
Signed-off-by: Javier Cardona <javier@cozybit.com>
Signed-off-by: Jason Mobarak <x@jason.mobarak.name>
Signed-off-by: Bob Copeland <me@bobcopeland.com>
2014-10-19 12:58:13 +03:00
Jouni Malinen
bc26ac50dd SAE: Add support for PMKSA caching on the station side
This makes wpa_supplicant SME create PMKSA cache entries from SAE
authentication and try to use PMKSA caching if an entry is found for the
AP. If the AP rejects the attempt, fall back to SAE authentication is
used.

Signed-off-by: Jouni Malinen <j@w1.fi>
2014-10-18 13:02:02 +03:00
Jouni Malinen
3eafc494d8 Fix CONFIG_NO_SCAN_PROCESSING=y build
ht_supported() was used but not defined in such a case.

Signed-off-by: Jouni Malinen <j@w1.fi>
2014-10-12 17:02:23 +03:00
Jouni Malinen
9d4ff04af3 Add external EAPOL transmission option for testing purposes
The new ext_eapol_frame_io parameter can be used to configure hostapd
and wpa_supplicant to use control interface for receiving and
transmitting EAPOL frames. This makes it easier to implement automated
test cases for protocol testing. This functionality is included only in
CONFIG_TESTING_OPTIONS=y builds.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2014-10-10 18:40:57 +03:00
Sunil Dutt
61fc90483f P2P: Handle improper WPS termination on GO during group formation
A P2P Client may be able to connect to the GO even if the WPS
provisioning step has not terminated cleanly (e.g., P2P Client does not
send WSC_Done). Such group formation attempt missed the event
notification about started group on the GO and also did not set the
internal state corresponding to the successful group formation.

This commit addresses the missing part by completing GO side group
formation on a successful first data connection if WPS does not complete
cleanly. Also, this commit reorders the STA authorization indications to
ensure that the group formation success notification is given prior to
the first STA connection to handle such scenarios.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2014-10-10 18:40:57 +03:00
Janusz Dziedzic
dc152f32b4 wpa_supplicant: Enable HT for IBSS
Enable HT20 for IBSS when HT is supported by the driver.

Signed-off-by: Janusz Dziedzic <janusz.dziedzic@tieto.com>
2014-10-04 18:54:22 +03:00
Jouni Malinen
f1a613118e P2P: Use only the -m config for P2P management device
Previously, the case of non-netdev P2P management device ended up
pulling in both the main interface (e.g., wlan0) and P2P Device
interface (from command line -m argument) as configuration. Similarly,
the main interface ended up included both configuration files. This is
not really helpful for various use cases, e.g., when permanent P2P group
information is stored in the P2P Devince interface, but it gets
duplicated in the main station interface configuration.

Clean this up by changing the -m<file> argument to replace, not
concatenate, configuration information. In other words, the main station
interface will not read this configuration and the P2P Device interface
(non-netdev) does not read parameters from the station interface
configuration file.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2014-10-03 22:50:21 +03:00
Jouni Malinen
a313d17de9 Extend random MAC address support to allow OUI to be kept
mac_addr=2 and preassoc_mac_addr=2 parameters can now be used to
configure random MAC address to be generated by maintaining the OUI part
of the permanent MAC address (but with locally administered bit set to
1). Other than that, these values result in similar behavior with
mac_addr=1 and preassoc_mac_addr=1, respectively.

Signed-off-by: Jouni Malinen <j@w1.fi>
2014-09-30 00:40:23 +03:00
Jouni Malinen
c267753ba2 Add support for using random local MAC address
This adds experimental support for wpa_supplicant to assign random local
MAC addresses for both pre-association cases (scan, GAS/ANQP) and for
connections. MAC address policy for each part can be controlled
separately and the connection part can be set per network block.

This requires support from the driver to allow local MAC address to be
changed if random address policy is enabled. It should also be noted
that number of drivers would not support concurrent operations (e.g.,
P2P and station association) with random addresses in use for one or
both.

This functionality can be controlled with the global configuration
parameters mac_addr and preassoc_mac_addr which set the default MAC
address policies for connections and pre-association operations (scan
and GAS/ANQP while not connected). The global rand_addr_lifetime
parameter can be used to set the lifetime of a random MAC address in
seconds (default: 60 seconds). This is used to avoid unnecessarily
frequent MAC address changes since those are likely to result in driver
clearing most of its state. It should be noted that the random MAC
address does not expire during an ESS connection, i.e., this lifetime is
only for the case where the device is disconnected.

The mac_addr parameter can also be set in the network blocks to define
different behavior per network. For example, the global mac_addr=1 and
preassoc_mac_addr=1 settings and mac_addr=0 in a home network profile
would result in behavior where all scanning is performed using a random
MAC address while connections to new networks (e.g.,
Interworking/Hotspot 2.0) would use random address and connections to
the home network would use the permanent MAC address.

Signed-off-by: Jouni Malinen <j@w1.fi>
2014-09-27 20:07:19 +03:00
Hu Wang
e5a4b85b2f WPS: Merge mixed-WPA/WPA2 credentials if received in same session
Some deployed APs send two credentials when in mixed-WPA/WPA2
configuration; one for the WPA-Personal/TKIP and the other for
WPA2-Personal/CCMP. Previously, this would result in two network blocks
getting added for the single AP. This can be somewhat confusing and
unnecessary, so merge such credentials into a single one that allows
both WPA and WPA2 to be used.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2014-08-29 20:25:18 +03:00
Jouni Malinen
86bd36f0d5 Add generic mechanism for adding vendor elements into frames
This adds following new control interface commands to allow arbitrary
vendor elements to be added into number of frames:

VENDOR_ELEM_ADD <frame id> <hexdump of elem(s)>
VENDOR_ELEM_GET <frame id>
VENDOR_ELEM_REMOVE <frame id> <hexdump of elem(s)>
VENDOR_ELEM_REMOVE <frame id> *

The following frames are supported in this commit (additional frames can
be added in the future):

0 = Probe Request frame in P2P device discovery
1 = Probe Response frame from P2P Device role
2 = Probe Response frame from P2P GO
3 = Beacon frame from P2P GO
4 = PD Req
5 = PD Resp
6 = GO Neg Req
7 = GO Neg Resp
8 = GO Neg Conf
9 = Invitation Request
10 = Invitation Response
11 = P2P Association Request
12 = P2P Association Response

One or more vendor element can be added/removed with the commands. The
hexdump of the element(s) needs to contain the full element (id, len,
payload) and the buffer needs to pass IE parsing requirements to be
accepted.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2014-07-07 12:25:09 +03:00
Li Jianyun
6891f0e6f4 Allow SCAN command to specify scan_ssid=1 SSIDs
The new "scan_id=<comma separated list of network ids>" parameter can
now be used to specify a list of network ids that have scan_ssid=1 to
indicate active scanning of the SSID. This adds the listed SSIDs to the
scan command to allow manual scan requests to perform active scans for
hidden SSIDs. For example, "SCAN scan_id=1,7,11" would run a scan with
the SSID fetched from the configured network blocks 1, 7, and 11
(assuming those are set with scan_ssid=1). The SSIDs will be included
even from network blocks that are currently disabled.

The maximum number of SSIDs added to the request is limited by the
driver support. If more than supported values are specified, the command
will fail (returns "FAIL").

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2014-07-02 12:52:08 +03:00
Jouni Malinen
3302b7c29f Rate limit SA Query procedure initiation on unprotected disconnect
There is no need to trigger new SA Query procedure to check the state of
the connection immediately after having performed such a check. Limit
the impact of burst of unprotected Deauth/Disassoc frames by starting a
new SA Query procedure only once at least 10 seconds has passed from the
previous SA Query that was triggered by reception of an unprotected
disconnection. The first SA Query procedure for each association does
not follow this rule to avoid issues with test cases that expect to see
an SA Query every time.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2014-06-19 20:56:32 +03:00
Jouni Malinen
504df28a1d Remove unused dump_freq_array()
This function is not used anymore.

Signed-off-by: Jouni Malinen <j@w1.fi>
2014-06-15 00:21:41 +03:00
Ilan Peer
a0c90bb073 P2P: Collect and use extended data on used frequencies
When the number of frequencies supported by the kernel is bigger than
one, and there is a need to pick a frequency for a new flow such as P2P
GO Negotiation or P2P Invitation, the flow should be able to pick the
best frequency among all the frequencies currently used by the device.

In order to prioritize between the currently used frequencies, add
the ability to collect additional data about each used frequency
(if the frequency is used by a station interface or P2P Client)
and when needed select the best frequency, where:

1. Infrastructure interfaces have highest priority
2. P2P Client interfaces have higher priority over AP/GO
   interfaces.

The rational is that the frequency of an AP/GO can change while
that of a station interface cannot.

Signed-off-by: Ilan Peer <ilan.peer@intel.com>
2014-06-15 00:21:40 +03:00
Jouni Malinen
0bbaa9b93f Validate driver extended capabilities length against buffer length
Prepare for new extended capabilities bits by checking that the local
buffer is large enough to contain all the bits the driver requests. The
existing buffers are large enough to include anything defined until now,
but it would be possible to add more definitions in the future, so
increase them a bit as well to make this more future proof.

Signed-off-by: Jouni Malinen <j@w1.fi>
2014-06-07 16:35:30 +03:00
Jouni Malinen
d4b951f31b Fix offchannel TX not to retransmit pending frame on callback
If the offchannel TX frame command was offloaded to the driver in
offchannel_send_action(), we must not send another copy of the frame if
a remain-on-channel event happens to be delivered between this TX
command and the matching TX status event. It was possible for the
duplicated frame to cause problems, e.g., with P2P invitation exchange
if the same Invitation Request frame got sent twice and only the first
one getting accepted by the peer.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2014-06-04 16:07:59 +03:00
Dmitry Shmidt
b19c098e75 Send authentication failure reason in wpas_auth_failed()
"WRONG_KEY"   - possibly wrong psk
"AUTH_FAILED" - authentication failure
"CONN_FAILED" - continiuos connection failure

Signed-off-by: Dmitry Shmidt <dimitrysh@google.com>
2014-05-16 18:08:39 +03:00
Hu Wang
dd10abccc8 MACsec: wpa_supplicant integration
Add MACsec to the wpa_supplicant build system and configuration file.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2014-05-09 20:42:44 +03:00
Rashmi Ramanna
41d5ce9e0b P2P: Optimize scan for GO during persistent group invocation
Scan for GO on the negotiated operating channel for few iterations
before searching on all the supported channels during persistent group
reinvocation. In addition, use the already known SSID of the group in
the scans. These optimizations reduce group formation time.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2014-03-25 15:38:33 +02:00
Dmitry Shmidt
d3c9c35f32 Add freq= parameter to 'set pno' command
This allows channels-to-be-scanned to be specified for PNO similarly to
the scan command.

Signed-off-by: Dmitry Shmidt <dimitrysh@google.com>
2014-03-21 23:56:46 +02:00
Peter Qiu
0f44ec8eba Add a reattach command for fast reassociate-back-to-same-BSS
Add "reattach" command to perform single-channel single-ssid scan
instead of full scan when trying to reconnect to the currently
"connected" network (assuming old scan results are not current enough to
skip the scan completely). This allows the scan result to come back in
much faster time. In ath9k, the scan took around 12 seconds with full
background scan, and only 0.1 second with the single-channel single-ssid
scan. Thus, take much less time for the client to re-establish
connection with the currently "connected" network.

Signed-hostap: Peter Qiu <zqiu@chromium.org>
2014-03-11 19:38:01 +02:00
Jouni Malinen
60b893dfb3 wpa_supplicant: Allow external management frame processing for testing
This enables more convenient protocol testing of AP and P2P
functionality in various error cases and unexpected sequences without
having to implement each test scenario within wpa_supplicant.
ext_mgmt_frame_handle parameter can be set to 1 to move all management
frame processing into an external program through control interface
events (MGMT-RX and MGMT-TX-STATUS) and command (MGMT_TX). This is
similar to the test interface that was added to hostapd previously, but
allows more control on offchannel operations and more direct integration
with the internal P2P module.

Signed-off-by: Jouni Malinen <j@w1.fi>
2014-03-08 20:21:21 +02:00
Ilan Peer
c16a7590cf wpa_supplicant: Add a configuration file for the P2P_DEVICE parameters
Add an option to specify a configuration file that can be used to hold
the P2P_DEVICE configuration parameters. If this option is not used, the
P2P_DEVICE configuration parameters will be read from interface
configuration file.

Note that it is advised to use this option in some cases such as:

If a P2P_DEVICE is supported by the driver, the wpa_supplicant creates a
dedicated P2P Device interface, where the configuration file used for
the main interface is used. As a consequence, if the configuration file
includes network definition etc., the wpa_supplicant will try to perform
station specific flows on the P2P Device interface which will fail.

If a P2P_DEVICE is supported by the driver and update_config is used,
the P2P Device configuration data will override the main interface
configuration data.

Signed-hostap: Ilan Peer <ilan.peer@intel.com>
2014-03-07 00:11:04 +02:00
Jouni Malinen
a6739e191e HS 2.0R2: Try to scan multiple times for OSU providers
Scan operation is not that reliable, so try couple of times if no
OSU provider matches are found during fetch_osu command.

Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
2014-02-26 01:24:24 +02:00
Jouni Malinen
230e373539 HS 2.0R2: Add GAS operation duration statistics into debug
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2014-02-26 01:24:23 +02:00
Jouni Malinen
b572df8650 HS 2.0R2: Add routine for fetching OSU provider information
The new wpa_cli fetch_osu command can be used to fetch information about
all OSU providers and write that to a text file with the icons in
separate files. cancel_osu_fetch command can be used to stop ongoing OSU
provider list fetch.

Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
2014-02-26 01:24:23 +02:00
Jouni Malinen
3d910ef497 Interworking: Prefer last added network during network selection
Previously, any network block could be used to select the BSS to connect
to when processing scan results after Interworking network selection.
This can result in somewhat unexpected network selection in cases where
credential preferences indicated that a specific network was selected,
but another network ended up getting used for the connection. While the
older networks continue to be valid, add special processing for this
initial post-interworking-connect case to get more consistent network
selection to match with the Interworking network selection result.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2014-02-25 22:37:57 +02:00
Jouni Malinen
f0e30c8410 Do not start another connect work while one is pending
It was possible for the connect or sme-connect radio work to get
re-scheduled while an earlier request was still pending, e.g.,
select_network is issued at the moment a scan radio work is in progress
and the old scan results are recent enough for starting the connection.
This could result in unexpected attempt to re-associate immediately
after completing the first connection.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2014-02-24 15:22:35 +02:00
Andrei Otcheretianski
b3253ebb73 wpa_supplicant: Complete radio works on disable event
While testing rfkill blocking of a scanning interface, it
was seen that the ongoing scan never completes. This happens
since EVENT_SCAN_RESULTS is discarded on a disabled interface.

Fix this and also other possible radio work completion issues
by removing all the radio works (including started) of the
disabled interface.

To be able to remove already started radio works, make their
callbacks be reentrant with deinit flag (when the work
is started), so each radio work should be able to handle
its own termination.

Signed-hostap: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
2014-02-16 00:06:23 +02:00
Jouni Malinen
0b5ff2ae12 WPS: Remove unused Credential AP Channel processing
Commit bd3a373767 added a mechanism to use
AP Channel attribute from within a Credential attribute to optimize
scans. However, this design is not actually used with the WPS NFC use
cases. With configuration token, the AP Channel attribute is in the same
container with the Credential attribute (and that was also handled in
the previous implementation). With connection handover, AP Channel
information is outside the Credential attribute as well.

Simplify implementation by removing the AP Channel within Credential
case. This allows wpas_wps_use_cred() to get the AP Channel from the
container instead of having to find this during credential iteration.

Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
2014-02-04 13:23:35 +02:00
Jouni Malinen
201b0f5fa6 P2P: Add test option to disable IP address assignment request
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
2014-01-27 21:44:30 +02:00
Jouni Malinen
25ef8529c1 P2P: Add support for IP address assignment in 4-way handshake
This new mechanism allows P2P Client to request an IPv4 address from the
GO as part of the 4-way handshake to avoid use of DHCP exchange after
4-way handshake. If the new mechanism is used, the assigned IP address
is shown in the P2P-GROUP-STARTED event on the client side with
following new parameters: ip_addr, ip_mask, go_ip_addr. The assigned IP
address is included in the AP-STA-CONNECTED event on the GO side as a
new ip_addr parameter. The IP address is valid for the duration of the
association.

The IP address pool for this new mechanism is configured as global
wpa_supplicant configuration file parameters ip_addr_go, ip_addr_mask,
ip_addr_star, ip_addr_end. For example:

ip_addr_go=192.168.42.1
ip_addr_mask=255.255.255.0
ip_addr_start=192.168.42.2
ip_addr_end=192.168.42.100

DHCP mechanism is expected to be enabled at the same time to support P2P
Devices that do not use the new mechanism. The easiest way of managing
the IP addresses is by splitting the IP address range into two parts and
assign a separate range for wpa_supplicant and DHCP server.

Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
2014-01-27 21:44:26 +02:00
Jouni Malinen
c4f87a701b P2P NFC: Add NFC tag enabling for static handover
The device with the NFC Tag can be configured to enable NFC to be used
with "P2P_SET nfc_tag 1" and "P2P_LISTEN" commands to allow static
handover to be used.

Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
2014-01-27 21:10:56 +02:00
Jouni Malinen
db6ae69e6b P2P NFC: Report connection handover as trigger for P2P
"NFC_REPORT_HANDOVER {INIT,RESP} P2P <req> <sel>" can now be used to
report completed NFC negotiated connection handover in which the P2P
alternative carrier was selected.

Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
2014-01-27 21:10:56 +02:00
Arif Hussain
253f2e3795 P2P: Apply unsafe frequency rules to available channels
This adds a QCA vendor specific nl80211 event to allow the driver to
indicate a list of frequency ranges that should be avoided due to
interference or possible known co-existance constraints. Such
frequencies are marked as not allowed for P2P use to force groups to be
formed on different channels.

If a P2P GO is operating on a channel that the driver recommended not to
use, a notification about this is sent on the control interface and
upper layer code may decide to tear down the group and optionally
restart it on another channel. As a TODO item, this could also be changed
to use CSA to avoid removing the group.

Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
2014-01-27 11:49:05 +02:00
Raja Mani
cf70d2981d wpa_supplicant: Schedule PNO on completion of ongoing sched_scan
When start PNO request comes from control interface, wpa_supplicant
should wait until ongoing sched_scan (triggered by wpa_supplicant)
gets cancelled. Issuing cancel sched_scan and start PNO scan
one after another from pno_start() would lead wpa_supplicant to clear
wps->sched_scanning flag while getting sched_scan stopped event
from driver for cancel sched_scan request. In fact, PNO scan will
be in progress in driver and wpa_s->sched_scanning will not be set
in such cases.

In addition to this change, RSSI threshold limit is passed as part of
start sched_scan request. This was previously set only in pno_start(),
but the same parameter should be available for generic sched_scan calls
as well and this can now be reached through the new PNO start sequence.

Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
2014-01-22 19:41:45 +02:00
Jouni Malinen
c48414af8f P2P: Limit join-a-group scans based on SSID from invitation
If we already know the SSID of the P2P group we are trying to join, use
that SSID to limit scan responses and BSS selection since we do not
really look for any other network in this case. In addition, this can
fix cases where the peer has just changed its SSID (e.g., started a new
group) and there may be multiple BSS entries for the same BSSID.

Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
2014-01-13 21:39:06 +02:00
Jouni Malinen
c60ba9f7ab Skip network disabling on expected EAP failure
Some EAP methods can go through a step that is expected to fail and as
such, should not trigger temporary network disabling when processing
EAP-Failure or deauthentication. EAP-WSC for WPS was already handled as
a special case, but similar behavior is needed for EAP-FAST with
unauthenticated provisioning.

Signed-hostap: Jouni Malinen <j@w1.fi>
2014-01-08 16:42:15 +02:00
Jouni Malinen
95fb2db242 P2P: Reject group formation on WPS provisioning failure
There is no need to wait for the 15 second group formation timeout to
clear the state if WPS failure is detected during P2P group formation.
Allow the WPS exchange steps (WSC_NACK and EAP-Failure) to be completed
and remove the group to get rid of the extra wait.

Signed-hostap: Jouni Malinen <j@w1.fi>
2014-01-07 10:45:12 +02:00
Jouni Malinen
b6a9590b34 Interworking: Keep up to two pending GAS_REQUEST responses
Previously, only the last response data was kept in memory. This
increases that to hold up to two last responses to allow some more
parallel operations to be requested. In addition, the response data is
now freed as soon as the external program has fetched it.

Signed-hostap: Jouni Malinen <j@w1.fi>
2014-01-07 10:45:12 +02:00
Jouni Malinen
1f965e622a Allow external programs to request wpa_radio work items
The new control interface command RADIO_WORK can be used by external
programs to request radio allocation slots from wpa_supplicant if
exclusive radio control is needed, e.g., for offchannel operations. If
such operations are done directly to the driver, wpa_supplicant may not
have enough information to avoid conflicting operations. This new
command can be used to provide enough information and radio scheduling
to avoid issues with such cases.

Signed-hostap: Jouni Malinen <j@w1.fi>
2014-01-07 10:45:10 +02:00
Jouni Malinen
6428d0a71f Do not start wpa_radio work during externally triggered scan
If an external program triggers a scan, wpa_supplicant does not have a
wpa_radio work item for this operation to protect against other
offchannel operations. This can result in operations failing, so try to
avoid damage by not starting any new wpa_radio work items during a scan
that was started by another process.

Signed-hostap: Jouni Malinen <j@w1.fi>
2014-01-07 10:45:10 +02:00
Jouni Malinen
6470f471e4 Remove unneeded scan delay on connection-in-progress
This type of protection against concurrent connection and scan
operations is now enforced through the wpa_radio work mechanism, so this
separate protection mechanism is not needed anymore.

Signed-hostap: Jouni Malinen <j@w1.fi>
2014-01-07 10:45:09 +02:00
Jouni Malinen
6ac4b15ef8 Use wpa_radio work for connection
This protects against conflicting offchannel operations during
connection (authentication, association, EAP exchanges, 4-way
handshake).

Signed-hostap: Jouni Malinen <j@w1.fi>
2014-01-07 10:45:09 +02:00
Jouni Malinen
e05e130837 P2P: Use radio work to protect offchannel Action frame exchanges
Signed-hostap: Jouni Malinen <j@w1.fi>
2014-01-07 10:45:09 +02:00
Jouni Malinen
e1d1c8e223 Use radio work for P2P Listen requests
Avoid concurrent P2P Listen operations with any other exclusive use of
the radio by using the radio work queuing mechanism. This removes some
of the earlier workarounds that postponed scans depending on other
operations.

Signed-hostap: Jouni Malinen <j@w1.fi>
2014-01-07 09:45:32 +02:00
Jouni Malinen
1b5d4714dd Use radio work for P2P scan requests
Avoid concurrent P2P scan requests with any other exclusive use of the
radio by using the radio work queuing mechanism. This removes some of
the earlier workarounds that postponed scans depending on other
operations.

Signed-hostap: Jouni Malinen <j@w1.fi>
2014-01-05 22:39:25 +02:00
Jouni Malinen
d12a51b5d2 Use radio work for scan requests
Avoid concurrent scan requests by using the radio work queuing
mechanism.

Signed-hostap: Jouni Malinen <j@w1.fi>
2014-01-05 22:37:50 +02:00
Jouni Malinen
b1ae396f59 Add framework for exclusive radio operations
The new radio work item concept can be used to request time for an
operation that requires exclusive radio control, e.g., a scan. Once the
radio is available, the registered callback function will be called.
radio_work_done() must be called once the exclusive radio operation has
been completed, so that the radio is freed for other operations. The
special case of deinit=1 is used to free the context data during
interface removal. That does not allow the callback function to start
the radio operation, i.e., it needs to free the allocated resources
and return.

Signed-hostap: Jouni Malinen <j@w1.fi>
2014-01-05 22:37:03 +02:00
Jouni Malinen
2f30cac36f Avoid unnecessary key clearing operations
Track set_key operations per-key index and clear keys on disconnection
only if the key was set (or may have been set which is the case for the
first operation after wpa_supplicant start).

Signed-hostap: Jouni Malinen <j@w1.fi>
2014-01-02 23:49:38 +02:00
Jouni Malinen
949938aadf Ask driver to report only new scan results if requested
If the BSS table within wpa_supplicant is flushed, request the driver to
flush its own scan result table during the next scan. This can avoid
unexpected old BSS entries showing up after BSS_FLUSH or FLUSH command
in cases where the driver may maintain its internal cache of scan
results (e.g., cfg80211 BSS table persists at least for 15 seconds).

In addition to doing this automatically on BSS_FLUSH/FLUSH, a new SCAN
command argument, only_new=1, can be used to request a manual scan
request to do same. Though, it should be noted that this maintains the
BSS table within wpa_supplicant. BSS_FLUSH followed by SCAN command can
be used to clear all BSS entries from both the driver and
wpa_supplicant.

Signed-hostap: Jouni Malinen <j@w1.fi>
2014-01-02 23:03:31 +02:00
Jouni Malinen
c64e3a08a9 P2P: Send received Presence Response information to ctrl_iface monitors
The P2P_PRESENCE_REQ command did not give any easily available
indication of the response received from the GO. Make this more useful
by providing such response (if received) as a ctrl_iface monitor event
(P2P-PRESENCE-RESPONSE).

Signed-hostap: Jouni Malinen <j@w1.fi>
2014-01-01 18:44:44 +02:00
Jouni Malinen
4848a38d85 Get rid of duplicated cipher suite and AKM definitions
WPA_CIPHER_* and CIPHER_* are used for the exact same set of cipher
suites with the main difference being that the WPA_CIPHER_* version is
suitable to be used as a bitfield. Similarly, WPA_KEY_MGMT_* and
KEY_MGMT_* have similar design for AKMs. There is no need to maintain
two separate copies of the definitions since the bitfield compatible
version can be used for both needs. Get rid of the CIPHER_* and
KEY_MGMT_* versions to clean up the implementation by getting rid of
unnecessary mapping functions.

Signed-hostap: Jouni Malinen <j@w1.fi>
2013-12-31 09:16:27 +02:00
Jouni Malinen
dc3906cb2d Show timing information about scan requests in debug log
Signed-hostap: Jouni Malinen <j@w1.fi>
2013-12-26 18:48:52 +02:00
Jouni Malinen
d81c73be18 Optional scan id for ctrl_iface SCAN requests
This allows users of wpa_supplicant control interface to figure out when
their specific scan command has been started and completed. For example:

CTRL-EVENT-SCAN-STARTED
> scan freq=2412,2417 passive=1 use_id=1
3
CTRL-EVENT-SCAN-RESULTS
CTRL-EVENT-SCAN-STARTED id=3
CTRL-EVENT-SCAN-RESULTS id=3

Signed-hostap: Jouni Malinen <j@w1.fi>
2013-12-26 18:48:52 +02:00
Jouni Malinen
a5f40eff18 Track whether scan was started by us or an external program
This can be used to improve scan behavior in cases external programs
request scans directly from the driver.

Signed-hostap: Jouni Malinen <j@w1.fi>
2013-12-26 18:27:48 +02:00
Jouni Malinen
88c2d48860 Allow passive scan to be requested with SCAN passive=1
This allows external programs to request wpa_supplicant to execute
a passive scan (i.e., do not send any Probe Request frames).

Signed-hostap: Jouni Malinen <j@w1.fi>
2013-12-26 18:27:48 +02:00
Jouni Malinen
69278f7328 Remove unused last_scan_full
This parameter was not really used for anything else apart from a debug
message in the same function that set it. In addition, cfg80211 returns
the set of scanned frequencies even for the full scan, so the code that
was setting this conditionally on frequency list not being there was not
really ever entered either.

Signed-hostap: Jouni Malinen <j@w1.fi>
2013-12-26 18:27:48 +02:00
Jouni Malinen
fee5234284 Allow channel list to be specified for SCAN command
The new freq=<frequency ranges> parameter to the SCAN command can be
used to request a scan to be performed on the specified set of channels
instead of on all channels. For example, "wpa_cli scan
freq=2400-2500,5180" would scan channels 1-14 and 36. Only the channels
that the driver indicates as enabled and that are within the specified
ranges are included in the request.

Signed-hostap: Jouni Malinen <j@w1.fi>
2013-12-26 16:55:44 +02:00
Johannes Berg
a12d34546a wpa_supplicant: Use monotonic time for last_scan check
This just serves to check if there was a scan within
the last 5 seconds, hence it should use monotonic time.
While at it, also use os_reltime_expired().

Signed-hostap: Johannes Berg <johannes.berg@intel.com>
2013-12-24 08:21:18 +02:00
Johannes Berg
51bffab117 WPS: Use monotonic time for AP connection attempt
This is only used for a debug message, but that message prints
the time since the last attempt, so it should use monotonic
time instead of wall clock.

Signed-hostap: Johannes Berg <johannes.berg@intel.com>
2013-12-24 08:19:47 +02:00
Johannes Berg
6473e5c842 wpa_supplicant: Use relative time for TKIP Michael MIC failures
The MMIC failure code should use monotonic time to check
whether 60 seconds have elapsed or not. For type-safety,
use struct os_reltime for the timestamp variable, and
also convert to using os_reltime_expired().

Signed-hostap: Johannes Berg <johannes.berg@intel.com>
2013-12-24 08:18:47 +02:00
Johannes Berg
151ab808fa P2P: Use monotonic time for GO client waiting
GO activation can fail if the first client doesn't connect
within a certain time, but this should not be dependent on
wall time -- use monotonic time instead.

While at it, use os_reltime_expired().

Signed-hostap: Johannes Berg <johannes.berg@intel.com>
2013-12-24 08:00:03 +02:00
Johannes Berg
c2be937ce7 wpa_supplicant: Use monotonic time for EAPOL RX workaround
The EAPOL RX workaround checks that the events are less than 100 ms
apart, so only uses relative times and should use monotonic time.

Signed-hostap: Johannes Berg <johannes.berg@intel.com>
2013-12-24 07:35:42 +02:00
Johannes Berg
acb69cec6f wpa_supplicant: Use monotonic time for RX/BSS times
The BSS table, scan timeout, and related functionality should use
monotonic time since they care about relative values (age) only.
Unfortunately, these are all connected, so the patch can't be split
further. Another problem with this is that it changes the driver wrapper
API. Though, it seems only the test driver is using this.

Signed-hostap: Johannes Berg <johannes.berg@intel.com>
2013-12-24 07:27:02 +02:00
Johannes Berg
46b8d4c004 wpa_supplicant: Use monotonic time for SA query timeout
The SA query timeout is just a regular timeout (currently
hard-coded to 1000 TU), so use monotonic time for it.

Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2013-12-24 07:17:25 +02:00
Jouni Malinen
202dec2a94 Add shared per-radio structure for wpa_supplicant
struct wpa_radio is used as a shared data structure between all struct
wpa_supplicant instances that share the same physical radio.

Signed-hostap: Jouni Malinen <j@w1.fi>
2013-11-24 21:20:14 +02:00