Commit graph

390 commits

Author SHA1 Message Date
Jouni Malinen
c1a14ef42f Do not check unsigned size is less than zero
The variables here are unsigned and as such, cannot have a negative
value. Use == 0 instead of <= 0 to make this cleaner.

Signed-off-by: Jouni Malinen <j@w1.fi>
2015-06-23 21:16:15 +03:00
Ilan Peer
f43c1ae798 P2P: Handle P2P Device dedicated interface parent removal
In case of a network interface removal, check if the interface
was also the parent interface of the P2P Device dedicated interface.
If this is the case, then stop the P2P Device functionality, and
remove the P2P Device dedicated interface.

In case that the interface is added again and P2P Device
functionality can be enabled again, add a new P2P Device dedicated
interface and allow further P2P Device functionality.

In case that the P2P Device dedicated interface is re-created, the
original P2P Device configuration file is needed, so store it in
the global params (instead in the wpa_interface configuration).

Signed-off-by: Ilan Peer <ilan.peer@intel.com>
2015-06-19 16:22:26 +03:00
Max Stepanov
734ddf6125 P2P: Add rx_freq parameter to Probe Request frame handler
In some cases, Probe Request frames can be received by a peer not only
on a listen channel. In this case an additional rx_freq parameter
explitly contains a Probe Request frame RX frequency. In case rx_freq is
set to 0, a Probe Request frame RX channel is assumed to be our own
listen channel (p2p->cfg->channel).

Signed-off-by: Max Stepanov <Max.Stepanov@intel.com>
Reviewed-by: Ilan Peer <ilan.peer@intel.com>
2015-06-14 23:16:55 +03:00
Avichal Agarwal
1a2f7ca1b8 D-Bus: Add WPS pbc-overlap Event
This sends an Event D-Bus signal with name "pbc-overlap" for
WPS-EVENT-OVERLAP.

Signed-off-by: Avichal Agarwal <avichal.a@samsung.com>
2015-06-10 20:51:30 +03:00
Jouni Malinen
eaa8eefed1 Replace MAX_SSID_LEN with SSID_MAX_LEN
This makes source code more consistent. The use within Android driver
interface is left as-is to avoid changes in the old PNO interface
definition.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2015-04-22 11:44:18 +03:00
Dmitry Shmidt
02e122a995 Reschedule scan from wpas_stop_pno if it was postponed
This reschedules the postponed scan request (if such a request is
pending) from EVENT_SCHED_SCAN_STOPPED event handler to speed up
scanning after PNO/sched_scan stop has been requested.

Signed-off-by: Dmitry Shmidt <dimitrysh@google.com>
2015-04-01 18:21:36 +03:00
Lauri Hintsala
ce18c10773 Add support for CONFIG_NO_ROAMING to Makefile
Commit e9af53ad39 introduced new
CONFIG_NO_ROAMING configuration parameter but unfortunately it was added
only to Android.mk. Enabling this parameter didn't have any effect when
Makefile was used to build wpa_supplicant. This commit fixes that problem
and cleans "unused variable" compiler warning.

Signed-off-by: Lauri Hintsala <lauri.hintsala@silabs.com>
2015-03-29 20:37:39 +03:00
Jouni Malinen
a52410c29f Allow PSK/passphrase to be set only when needed
The new network profile parameter mem_only_psk=1 can be used to specify
that the PSK/passphrase for that network is requested over the control
interface (ctrl_iface or D-Bus) similarly to the EAP network parameter
requests. The PSK/passphrase can then be configured temporarily in a way
that prevents it from getting stored to the configuration file.

For example:

Event:
CTRL-REQ-PSK_PASSPHRASE-0:PSK or passphrase needed for SSID test-wpa2-psk

Response:
CTRL-RSP-PSK_PASSPHRASE-0:"qwertyuiop"

Note: The response value uses the same encoding as the psk network
profile parameter, i.e., passphrase is within double quotation marks.

Signed-off-by: Jouni Malinen <j@w1.fi>
2015-03-28 11:05:13 +02:00
Krishna Vamsi
c41d0840a1 nl80211: Allow driver-based roam to change ESS
This extends NL80211_CMD_ROAM event processing to allow the driver to
roam to another ESS (different SSID) when using offloaded BSS selection.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2015-03-24 21:13:28 +02:00
Avraham Stern
9bd566a33a Delay AP selection if all networks are temporarily disabled
If all networks are temporarily disabled, delay AP selection until at
least one network is enabled. Running AP selection when all networks are
disabled is useless as wpa_supplicant will not try to connect. In
addition, it will result in needless scan iterations that may delay the
connection when it is needed.

Signed-off-by: Avraham Stern <avraham.stern@intel.com>
2015-03-22 20:53:58 +02:00
Victor Goldenshtein
6ceea4c3cb Restart sched_scan on channel list change
The channel list can be changed as a result of arriving beacon hints
during normal scan or as a result of local Reg-Domain change. Some
passive channels can become active and needs to be reconfigured
accordingly for the scheduled scan.

This fixes the connection to hidden SSIDs on 5 GHz band during default
Reg-Domain 00 (world roaming).

Signed-off-by: Victor Goldenshtein <victorg@ti.com>
Signed-off-by: Eliad Peller <eliad@wizery.com>
2015-03-20 15:56:59 +02:00
Jouni Malinen
1d246a1db9 Make rate-not-supported debug print more useful
It looks like "hardware does not support required rate 1.0 Mbps" has
started showing up in some hwsim test cases as a reason for failure.
This should not really occur with mac80211_hwsim, so add more details to
the debug print to make it easier to figure out what exactly happened.

Signed-off-by: Jouni Malinen <j@w1.fi>
2015-03-07 15:35:40 +02:00
Sunil Dutt
c10ca2a66f TDLS: Allow driver to request TDLS Discovery Request initiation
This extends the TDLS operation request mechanism to allow TDLS
Discovery Request to be initiated by the driver similarly to the
existing Setup and Teardown requests.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2015-03-06 21:08:54 +02:00
Ahmad Kholaif
bd0f68c473 DFS: wpa_supplicant event processing
Add radar event processing logic for AP/P2P GO. The DFS processing
functions from hostapd are now used for these wpa_supplicant cases as
well for both offloaded and non-offloaded DFS.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2015-03-05 17:24:16 +02:00
Jouni Malinen
c28059091a Do not add blacklist entries based on normal disconnect request cases
There are number of cases where wpa_supplicant requests the current
connection to be disconnected before starting a new operation. Such
cases do not really indicate that there was an error in connecting or a
disconnection initiated by the AP, so do not add a temporary blacklist
entry in such sequences.

Signed-off-by: Jouni Malinen <j@w1.fi>
2015-03-01 15:54:24 +02:00
Jouni Malinen
44b9ea5bb2 P2P: Do not allow scan or normal association on cfg80211 P2P Device
The dedicated P2P management instance (wpas->p2p_mgmt == 1) using
cfg80211 P2P Device cannot be used for non-P2P uses or connection (there
is no netdev). Reject or ignore such operations to avoid unexpected
operations if enabled network blocks are configured in the
wpa_supplicant instance used to control this interface.

Signed-off-by: Jouni Malinen <j@w1.fi>
2015-03-01 11:23:09 +02:00
Jouni Malinen
0d2030ee20 Use estimated throughput to improve roaming selection
Previously, within-ESS roaming was skipped if the selected BSS did not
have a higher signal strength than the current BSS regardless of AP
capabilities. This could result in not moving to a BSS that would
provide higher throughput, e.g., due to larger channel bandwidth or
higher rates (HT/VHT MCS).

Use estimated throughput information from scan result processing to
allow within-ESS roaming if the selected BSS is likely to provide better
throughput even if the current BSS has larger RSSI.

Signed-off-by: Jouni Malinen <j@w1.fi>
2015-02-22 11:45:45 +02:00
Matthieu Mauger
71d77adb6d Update current BSS level when signal change event occurs
When an EVENT_SIGNAL_CHANGE occurs the bgscan is informed about this
change but the new RSSI value is not stored. In consequence, when
roaming candidates are evaluated, the RSSI value of the current BSS used
to compare is an old one obtained during the last scan rather than the
new one given by the signal change event. This leads sometimes to bad
decision when selecting a new BSS for roaming.

This patch solves the issue by updating the current BSS level when
receiving a signal change event in order to have a very up-to-date
current signal value when choosing an new BSS.

Signed-off-by: Matthieu Mauger <matthieux.mauger@intel.com>
2015-02-21 16:07:53 +02:00
Ilan Peer
f1609f119a wpa_supplicant: Cancel sched_scan when stopping countermeasures
When stopping the TKIP countermeasures, it would be preferable to
connect immediately. However if scheduled scan is in progress,
a connection attempt will be done only when scan results are received,
so cancel the scheduled scan to allow immediate scan and connection
attempt.

Signed-off-by: Ilan Peer <ilan.peer@intel.com>
2015-02-21 16:07:53 +02:00
Jouni Malinen
b0e669beeb P2P: Fix P2P_CONNECT-auto fallback to GO Neg with group interface
If a separate P2P group interface was used, P2P_CONNECT-auto fallback to
GO Negotiation could result in use of freed memory and segmentation
fault. This happened in cases where the peer GO was found in some old
scans, but not in the first scan triggered by the P2P_CONNECT-auto
command ("P2P: Peer was found running GO in older scan -> try to join
the group" shows up in the debug log). In addition, the GO would still
need to reply to PD Request to allow this code path to be triggered.

When five scans for the GO were completed in this sequence, the P2P
group interface was removed as part of falling back to GO Negotiation.
However, that ended up dereferencing the freed wpa_s instance at the end
of scan event processing. Fix this by reordering code a bit and breaking
out from EVENT_SCAN_RESULTS processing if the interface could have been
removed.

Signed-off-by: Jouni Malinen <j@w1.fi>
2015-02-08 13:35:14 +02:00
Jouni Malinen
ba4226130e Simplify eapol_sm_notify_pmkid_attempt()
Drop the unneeded 'attempt' argument. This was originally used for
indicating an aborted PMKID caching attempt, but a fix in 2006 removed
the only such user and since that time, only attempt == 1 has been used.

Signed-off-by: Jouni Malinen <j@w1.fi>
2015-01-28 13:09:31 +02:00
Jouni Malinen
3f56a2b746 Ignore pmf=1 default if driver does not support PMF
Connection with a PMF enabled AP will fail if we try to negotiate PMF
while the local driver does not support this. Since pmf=1 does not
require PMF for a successful connection, it can be ignored in such a
case to avoid connectivity issues with invalid configuration. This makes
it somewhat easier to allow upper layer programs to use pmf=1 default
regardless of driver capabilities.

Signed-off-by: Jouni Malinen <j@w1.fi>
2015-01-27 12:38:52 +02:00
Jouni Malinen
98cd3d1c3b Preparations for variable length KCK and KEK
This modifies struct wpa_ptk to allow the length of KCK and KEK to be
stored. This is needed to allow longer keys to be used, e.g., with
Suite B 192-bit level.

Signed-off-by: Jouni Malinen <j@w1.fi>
2015-01-27 01:26:49 +02:00
Ben Rosenfeld
d90bfa97f4 Move external_scan_running to wpa_radio
external_scan_running should be common to all interfaces that share a
radio. This fixes a case where external_scan_running was set on a single
interface, but did not block scan on other interfaces.

Signed-off-by: Ben Rosenfeld <ben.rosenfeld@intel.com>
2015-01-20 01:57:59 +02:00
Stefan Tomanek
79cd993a62 Add address masks to BSSID lists
In many applications it is useful not just to enumerate a group of well
known access points, but to use a address/mask notation to match an
entire set of addresses (ca:ff:ee:00:00:00/ff:ff:ff:00:00:00).

This change expands the data structures used by MAC lists to include a
mask indicating the significant (non-masked) portions of an address and
extends the list parser to recognize mask suffixes.

Signed-off-by: Stefan Tomanek <stefan.tomanek@wertarbyte.de>
2015-01-10 17:35:53 +02:00
Stefan Tomanek
b83e455451 Add network specific BSSID black and white lists
This change adds the configuration options "bssid_whitelist" and
"bssid_blacklist" used to limit the AP selection of a network to a
specified (finite) set or discard certain APs.

This can be useful for environments where multiple networks operate
using the same SSID and roaming between those is not desired. It is also
useful to ignore a faulty or otherwise unwanted AP.

Signed-off-by: Stefan Tomanek <stefan.tomanek@wertarbyte.de>
2015-01-10 17:35:53 +02:00
Jouni Malinen
635874b55a Handle interface disabled/enabled more consistently
It was possible for the interface not to be marked in INTERFACE_DISABLED
state in case the event was processed for P2P GO because the wpa_s
instance could have been removed in case of a separate group interface.
Change the state first to avoid leaving different state for the case
where separate group interface is not used.

Mark scan to be a normal scan on INTERFACE_ENABLED so that scanning
rules (e.g., skip scan if no networks enabled) get used consistently.

Signed-off-by: Jouni Malinen <j@w1.fi>
2015-01-08 22:43:48 +02:00
Jouni Malinen
8f2cf37923 P2P: Indicate reason=UNAVAILABLE for group netdev going down
There is a race condition between receiving an AP stopped event and
netdev down event. These resulted in different group removal reasons on
a GO device (UNAVAILABLE for stop AP event coming first and REQUESTED
for netdev event first). Make this more consistent by reporting
UNAVAILABLE for both possible cases.

Signed-off-by: Jouni Malinen <j@w1.fi>
2015-01-08 22:43:48 +02:00
Eliad Peller
8c42b36902 WMM AC: Reconfigure tspecs on reassociation to the same BSS
The specification requires the tspecs to be kept upon reassociation to
the same BSS. Save the last tspecs before such reassociation, and
reconfigure on the association notification.

Note that the current flow is not transparent to the user
(it is notified about deauth/reassoc and tspec removal/addition).

Signed-off-by: Eliad Peller <eliadx.peller@intel.com>
2015-01-04 18:41:00 +02:00
Eliad Peller
fecc2bb5a8 WMM AC: Delete tspecs on roaming
In case of roaming, we don't get disassoc notification, but
still want to remove the existing tspecs.

Move the wmm_ac_notify_disassoc() call to the state change
function, which get called also on roaming.

Signed-off-by: Eliad Peller <eliadx.peller@intel.com>
2015-01-04 18:32:59 +02:00
Jouni Malinen
4e70bbf1c6 SAE: Clear keys from memory on disassociation
There is no need to keep temporary keys in memory beyond the end of the
association, so explicitly clear any SAE buffers that can contain keys
as soon as such keys are not needed.

Signed-off-by: Jouni Malinen <j@w1.fi>
2014-12-29 20:00:02 +02:00
Jouni Malinen
9a700ff9ef Ignore auth/assoc timeout events in mesh configuration
It was possible for auth/assoc timeout/failure event from the driver to
result in unexpected processing during mesh group setup if that
operation was started before the previously started driver operation to
association/connect had completed. Since those events cannot happen in
mesh cases, ignore them to avoid issues due to this corner case.

For example, monitor_iface_unknown_sta followed by wpas_mesh_secure test
case resulted in failure without this change.

Signed-off-by: Jouni Malinen <j@w1.fi>
2014-11-30 15:53:11 +02:00
Andrei Otcheretianski
70d1e72849 wpa_supplicant: Handle link measurement requests
Send link measurement response when a request is received. Advertise
only RCPI, computing it from the RSSI of the request. The TX power field
is left to be filled by the driver. All other fields are not published.

Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
2014-11-22 21:45:07 +02:00
Assaf Krauss
d89c0701db wpa_supplicant: Add support for Neighbor Report
Add the ability to send a Neighbor Report Request (part of
RRM). Requester is then notified once the report arrives.

Signed-off-by: Assaf Krauss <assaf.krauss@intel.com>
2014-11-22 21:23:14 +02:00
Assaf Krauss
b361d580ec SME: Add RRM support to association request
In case the AP we are associating with advertises support for RRM,
advertise our own RRM support in the (Re)Association Request frame. This
is done by adding an RRM Capabilities IE. The underlying driver is
expected to further add a Power Capabilities IE to the request, and set
the Radio Measurement flag in the Capability Info field. At this point
the RRM Capabilities IE advertises no measurement support.

Signed-off-by: Assaf Krauss <assaf.krauss@intel.com>
2014-11-22 21:13:45 +02:00
Jouni Malinen
75d65857d5 WNM: Use recent scan results on BSS transition request
If the last scans are recent (for now, less than ten seconds old), use
them instead of triggering a new scan when a BSS Transition Management
Request frame is received. As a fallback, allow a new scan to be
triggered if no matches were found.

Signed-off-by: Jouni Malinen <j@w1.fi>
2014-11-22 20:17:47 +02:00
Jouni Malinen
d0b9ab69f6 WNM: Move transition candidate list processing to normal scan
This makes it easier to optimize transition request processing.

Signed-off-by: Jouni Malinen <j@w1.fi>
2014-11-22 18:40:03 +02:00
Moshe Benji
d1f880013a WMM AC: Handle TSPEC action frames
Add the TSPEC to the driver on successful TSPEC ADDTS response. Delete
the TSPEC when receiving DELTS action.

Signed-off-by: Moshe Benji <moshe.benji@intel.com>
Signed-off-by: Eliad Peller <eliad@wizery.com>
2014-11-16 21:07:08 +02:00
Moshe Benji
a0413b1734 WMM AC: Parse WMM IE on association
Initialize WMM AC data structures upon successful association
with an AP that publishes WMM support, and deinitialize the data
structure when the association is no longer valid.

Signed-off-by: Moshe Benji <moshe.benji@intel.com>
Signed-off-by: Eliad Peller <eliadx.peller@intel.com>
2014-11-16 20:47:34 +02:00
Masashi Honma
eac0231642 mesh: Fix segmentation fault by repeating MESH_GROUP_ADD/REMOVE
Signed-off-by: Natsuki Itaya <Natsuki.Itaya@jp.sony.com>
Signed-off-by: Masashi Honma <masashi.honma@gmail.com>
2014-11-16 19:43:11 +02:00
Thomas Pedersen
476e6bb68d mesh: Add mesh mode config option
Modify network mode to support mode number 5 when CONFIG_MESH is
enabled.

Signed-off-by: Javier Lopez <jlopex@gmail.com>
Signed-off-by: Jason Mobarak <x@jason.mobarak.name>
Signed-off-by: Thomas Pedersen <thomas@noack.us>
2014-10-25 17:45:35 +03:00
Thomas Pedersen
a3335ef518 mesh: Avoid join if already joined a mesh group
Signed-off-by: Javier Lopez <jlopex@gmail.com>
Signed-off-by: Thomas Pedersen <thomas@noack.us>
2014-10-25 17:45:35 +03:00
Bob Copeland
5f92659d88 mesh: Add mesh peering manager
The mesh peering manager establishes and maintains links among
mesh peers, tracking each peer link via a finite state machine.

This implementation supports open mesh peerings.

[assorted fixes from Yu Niiro <yu.niiro@gmail.com>]
[more fixes from Masashi Honma <masashi.honma@gmail.com>]
Signed-off-by: Javier Lopez <jlopex@gmail.com>
Signed-off-by: Javier Cardona <javier@cozybit.com>
Signed-off-by: Ashok Nagarajan <ashok.dragon@gmail.com>
Signed-off-by: Jason Mobarak <x@jason.mobarak.name>
Signed-hostap: Bob Copeland <me@bobcopeland.com>
2014-10-25 17:45:31 +03:00
Thomas Pedersen
8319e3120d mesh: Add mesh mode routines
Add routines to (de)initialize mesh interface data structures and
join and leave mesh networks.

Signed-off-by: Javier Lopez <jlopex@gmail.com>
Signed-off-by: Javier Cardona <javier@cozybit.com>
Signed-off-by: Jason Mobarak <x@jason.mobarak.name>
Signed-off-by: Thomas Pedersen <thomas@noack.us>
2014-10-25 17:43:20 +03:00
Chet Lanctot
b41f26845a Add support for offloading key management operations to the driver
This commit introduces a QCA vendor command and event to provide an
option to use extended versions of the nl80211 connect/roam operations
in a way that allows drivers to offload key management operations to the
driver/firmware.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2014-10-23 18:38:50 +03:00
Jouni Malinen
3eafc494d8 Fix CONFIG_NO_SCAN_PROCESSING=y build
ht_supported() was used but not defined in such a case.

Signed-off-by: Jouni Malinen <j@w1.fi>
2014-10-12 17:02:23 +03:00
Janusz Dziedzic
dc152f32b4 wpa_supplicant: Enable HT for IBSS
Enable HT20 for IBSS when HT is supported by the driver.

Signed-off-by: Janusz Dziedzic <janusz.dziedzic@tieto.com>
2014-10-04 18:54:22 +03:00
Jouni Malinen
6e252b0db3 WPS: Fix WPS-in-search check when STA_AUTOCONNECT is disabled
If "STA_AUTOCONNECT 0" has been used to disable automatic connection on
disconnection event and the driver indicates multiple disconnection
events for the disconnection from the current AP when WPS is started, it
could have been possible to hit a case where wpa_s->disconnected was set
to 1 during WPS processing and the following scan result processing
would stop the operation.

wpa_s->key_mgmt == WPA_KEY_MGMT_WPS check was trying to avoid to skip
autoconnect when WPS was in use, but that does not seem to work anymore.
Fix this by checking through wpas_wps_searching() as well to avoid
setting wpa_s->disconnect = 1 when there is an ongoing WPS operation.

Signed-off-by: Jouni Malinen <j@w1.fi>
2014-09-28 11:03:48 +03:00
Jouni Malinen
068e38771e STA: Update scan results for ap_scan=1 skip-selection case also
The commit 5cd4740580 has rearranged the
update scan results code and hence the IEs were not getting updated
properly for ap_scan=1 case. This can result in a 4-way handshake
failure in the roaming case (IE mismatch in 3/4 EAPOL). Fix this by
updating the scan results even if ap_scan=1 is used and network does not
need to get reselected based on association information.

Signed-off-by: Jithu Jance <jithu@broadcom.com>
Signed-off-by: Dmitry Shmidt <dimitrysh@google.com>
Signed-off-by: Jouni Malinen <j@w1.fi>
2014-09-13 17:31:58 +03:00
Dmitry Shmidt
abc05534aa Remove WPA_EVENT_SCAN_STARTED message from MSG_INFO log
Signed-off-by: Dmitry Shmidt <dimitrysh@google.com>
2014-09-07 19:54:39 +03:00