Commit graph

3165 commits

Author SHA1 Message Date
Jouni Malinen
4a393fe9f8 WPS: Do not indicate PBC overlap for the same BSS
Even if the UUID would have a mismatch, e.g., due to no UUID known for
the target in a new WPS PBC instance, do not indicate PBC session
overlap if the BSSID is same in the two entries. This should not really
happen in normal use cases, but can happen at least in some test
scenarios where the same BSSID is used in consecutive test cases and the
old BSS entry remains in cfg80211 cache.

Signed-off-by: Jouni Malinen <j@w1.fi>
2014-12-25 16:37:12 +02:00
Jouni Malinen
3a322496f9 mesh: Delay Authentication frame process with no_auto_peer
There is a possible race condition between receiving the
NEW_PEER_CANDIDATE event and the Authentication frame from the peer.
Previously, if the Authentication frame RX event was indicated first,
that frame got dropped silently. Now, this frame is still dropped, but a
copy of it is stored and the frame gets processed on the following
NEW_PEER_CANDIDATE event if that is received for the same peer within
two seconds.

Signed-off-by: Jouni Malinen <j@w1.fi>
2014-12-23 13:44:38 +02:00
Jouni Malinen
d97a3c4885 SME: Optimize OBSS scanning
Include only the potentially affected channel range in OBSS scans to
reduce the amount of offchannel time needed for scanning when requested
by the AP.

Signed-off-by: Jouni Malinen <j@w1.fi>
2014-12-22 22:07:03 +02:00
Jouni Malinen
267ac3bcd6 Add more debug prints for WPA/RSN selection issues for connection
ap_ft_sae test case managed to hit a somewhat unclear error case which
resulted in "WPA: Failed to select WPA/RSN" print and not enough
information to figure out what exactly had went wrong.

Signed-off-by: Jouni Malinen <j@w1.fi>
2014-12-22 13:49:52 +02:00
Masashi Honma
d5b95325de mesh: Fill Number of Peerings field in Mesh Formation Info
Signed-off-by: Masashi Honma <masashi.honma@gmail.com>
2014-12-21 23:59:40 +02:00
Masashi Honma
46e8d90f6a mesh: Add debug message when peering limit is reached
Signed-off-by: Masashi Honma <masashi.honma@gmail.com>
2014-12-21 23:55:44 +02:00
Masashi Honma
4b4093686b mesh: Make maximum number of peer links configurable
Maximum number of peer links is maximum number of connecting mesh peers
at the same time. This value is 0..255 based on the
dot11MeshNumberOfPeerings range.

Signed-off-by: Masashi Honma <masashi.honma@gmail.com>
2014-12-21 23:52:31 +02:00
Masashi Honma
9c58c5f72c mesh: Make beacon interval configurable
Signed-off-by: Masashi Honma <masashi.honma@gmail.com>
2014-12-21 23:38:20 +02:00
Masashi Honma
3b797130d7 doc: Remove error on document creation
Unexpected trailing zero causes following error.

wpa_supplicant.sgml:472:53:E: character data is not allowed here

Signed-off-by: Masashi Honma <masashi.honma@gmail.com>
2014-12-21 23:36:55 +02:00
Jouni Malinen
422ba11e30 Flush WPS registrar state on wpa_supplicant FLUSH command
This helps hwsim test cases by avoiding undesired state from previously
executed test cases affecting following tests.

Signed-off-by: Jouni Malinen <j@w1.fi>
2014-12-21 17:47:42 +02:00
Jouni Malinen
209702d4c9 Add possibility to set the setband parameter
Commit faf9a8585d added mechanism for
selecting 2.4 or 5 GHz band for scan operation. However, no mechanism
for setting the setband value was added at that time. This commit adds a
new SET ctrl_iface parameter to allow the setband functionality to be
used. "SET setband <AUTO/5G/2G>" can be used to select all bands, 5 GHz
band only, or 2.4 GHz band only.

Signed-off-by: Jouni Malinen <j@w1.fi>
2014-12-19 22:56:41 +02:00
Sunil Dutt
ee82e33d6a Do not trigger the scan during initialization on Android platforms
Android framework maintains a state to process the scan results after
the scan is issued. If wpa_supplicant issues the scan during the
initialization, the one issued by the framework may fail (with EBUSY) if
the host driver is already processing the scan. Thus, the scan results
returned for the first scan triggered by wpa_supplicant are not
processed for getting displayed resulting in delay for the display of
the first scan results after the Wi-Fi subsystem initialization. Thus,
trigger the scan only based on the framework request on Android.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2014-12-19 15:24:33 +02:00
Jouni Malinen
e69ae5ff31 Reject new SCAN commands if there is a pending request
FAIL-BUSY was already returned for the case where a scan had been
started, but with the radio work design, it would have been possible to
schedule multiple scan requests if a non-scan radio work was in
progress. Multiple back-to-back scans are not usually very helpful, so
reject this type of cases where the SCAN command would be used to build
such a sequence.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2014-12-19 15:14:38 +02:00
Jithu Jance
49e1e9ca88 P2P: Avoid truncation of long listen operation due to offchan tx
On receiving the cancel remain on channel event, the pending_tx
is scheduled immediately and returned. This was preventing
the wpas_p2p_listen_start function from execution thereby resulting
in termination of the long listen operation.

Signed-off-by: Jithu Jance <jithu@broadcom.com>
2014-12-18 16:41:40 +02:00
Jouni Malinen
0855e2e188 Do not allow network block scan_freq override SCAN command frequencies
The manual scan operations with the SCAN command are supposed to have
independent set of scan frequencies, so do not allow scan_freq
parameters to override scanned frequencies for scans that were triggered
with a SCAN command.

Signed-off-by: Jouni Malinen <j@w1.fi>
2014-12-15 00:55:56 +02:00
Masashi Honma
5b78493f3b mesh: Add mesh interface creation command for mesh gate
The mesh gate is used to bridge (or route) between mesh network and
another network. For example, mesh gate acts as router between mesh
network and IEEE 802.11 BSS network.

This command makes a virtual mesh interface to be used for mesh gate.

This command expects to be used like this.

wpa_cli -i wlan0 MESH_INTERFACE_ADD ifname=mesh0
wpa_cli -i mesh0 add_network
wpa_cli -i mesh0 set_network 0 ssid '"commell_2X_mmm"'
wpa_cli -i mesh0 set_network 0 mode 5
wpa_cli -i mesh0 set_network 0 frequency 2412
wpa_cli -i mesh0 set_network 0 key_mgmt SAE
wpa_cli -i mesh0 set_network 0 psk '"01234567"'
wpa_cli -i mesh0 mesh_group_add 0
wpa_cli -i wlan0 mesh_group_remove mesh0

Signed-off-by: Masashi Honma <masashi.honma@gmail.com>
2014-12-14 23:27:43 +02:00
Jouni Malinen
e77007132e Extend wpa_supplicant STA* ctrl_iface commands for mesh
Since mesh functionality uses struct hostapd_data to maintain peer
state, the existing STA* control interface commands can be used to
display information about the peers.

Signed-off-by: Jouni Malinen <j@w1.fi>
2014-12-14 20:14:30 +02:00
Jouni Malinen
b0f33467a5 Clean up VHT override max A-MPDU override calculation
There is no need to use runtime call to find_first_bit() to determine
shift amount for a constant integer.

Signed-off-by: Jouni Malinen <j@w1.fi>
2014-12-14 18:48:59 +02:00
Led
2797486c4f Fix bashisms in wps-ap-cli script
Option '-p' of 'read' command may be unsupported in some POSIX-complete
shells. So replace 'read -p' with 'echo -n'/'read' pair.

Signed-off-by: Oleksandr Chumachenko <ledest@gmail.com>
2014-12-14 18:27:54 +02:00
Arkadiusz (Arkq) Bokowy
7b244d577a wpa_gui: Quiet mode - disable tray icon messages
If tray icon messages are perceived as disturbing, one can pass `-q`
parameter on the command line to disable them permanently.

Signed-off-by: Arkadiusz Bokowy <arkadiusz.bokowy@gmail.com>
2014-12-14 17:26:42 +02:00
Arkadiusz (Arkq) Bokowy
2087b64fef wpa_gui: More informative tray icon tool tip message
Show associated network SSID in the tool tip message of the
application's tray icon. When network is not associated, then simple
"(not-associated)" message is shown.

Signed-off-by: Arkadiusz Bokowy <arkadiusz.bokowy@gmail.com>
2014-12-14 17:23:43 +02:00
Jouni Malinen
81648d0041 SAE: Report connection failure if SME cannot build auth frame
Instead of just stopping connection process and network discovery,
report SAE failures to build Authentication frames (e.g., due to missing
password) as a connection failure to get the normal retry mechanism into
use.

Signed-off-by: Jouni Malinen <j@w1.fi>
2014-12-14 16:48:38 +02:00
Jouni Malinen
8e3afd7f6c offchannel: Use wpas_get_tx_interface() src parameter more consistently
Both the wpa_s->pending_action_src and src argument to
wpas_get_tx_interface() were used somewhat randomly. Make this more
consistent since these values are pointing to the same address and the
implementation is easier to understand when it is obvious that there is
only one address being used.

Signed-off-by: Jouni Malinen <j@w1.fi>
2014-12-14 15:47:04 +02:00
Jouni Malinen
568475b70b HS 2.0: Allow CANCEL_FETCH_OSU to stop at scan completion
There is no need to start the GAS/ANQP fetch if the FETCH_OSU operation
has already been canceled.

Signed-off-by: Jouni Malinen <j@w1.fi>
2014-12-14 02:28:03 +02:00
Jouni Malinen
f77cedc11a WPS ER: Remove unnecessary return value
wps_er_deinit() cannot fail and it does not return anything, so neither
should wpas_wps_er_stop().

Signed-off-by: Jouni Malinen <j@w1.fi>
2014-12-14 02:28:03 +02:00
Jouni Malinen
5407c69d15 Remove unnecessary STA_AUTOCONNECT handler function
This function could not fail and it can be replaced with a single
line variable update that takes less code than the function call.

Signed-off-by: Jouni Malinen <j@w1.fi>
2014-12-13 19:27:41 +02:00
Jouni Malinen
a1144000cd Remove unnecessary return value
wpa_bss_flush*() cannot fail and as such, there is no need for
wpa_supplicant_ctrl_iface_bss_flush() to return a value either.

Signed-off-by: Jouni Malinen <j@w1.fi>
2014-12-13 19:22:23 +02:00
Jouni Malinen
5ac73acf12 Simplify eapol_sm_get_mib() result handling
This function cannot return negative value, so no need to check for
that. If there is not enough room in the buffer or if something
unexpected happens, 0 is returned.

Signed-off-by: Jouni Malinen <j@w1.fi>
2014-12-13 19:15:38 +02:00
Jouni Malinen
43a66ecba3 Fix SCAN control interface command error cases
Update the scan parameters in wpa_s only in case the scan command is
going to be executed. In other words, do not change the parameters for
an ongoing scan (the SCAN command is rejected with FAIL-BUSY) or if any
of the parameters is invalid.

Signed-off-by: Jouni Malinen <j@w1.fi>
2014-12-12 01:12:15 +02:00
Jouni Malinen
2961bfa8e1 Remove unused send_eapol() driver op
The send_eapol() callback was used by driver_test.c, but with that
removed, there is no remaining users of the alternative EAPOL frame
transmitting mechanism in wpa_supplicant, i.e., all remaining driver
interfaces use l2_packet instead. Remove the send_eapol() to get rid of
unused code.

Signed-off-by: Jouni Malinen <j@w1.fi>
2014-12-11 15:40:07 +02:00
Jouni Malinen
b68d602dc4 Fix ANQP_GET/HS20_GET_ANQP parsing to skip space after address
The space following the BSSID was not skipped properly if the following
parameter started with the "hs20:" prefix. For other cases, atoi() ended
up ignoring the space, but it is cleaner to skip it anyway for all
cases.

Signed-off-by: Jouni Malinen <j@w1.fi>
2014-12-11 15:18:11 +02:00
Jouni Malinen
42a697256e P2P: Allow cross connection on the parent interface
Previously, any P2P capable interface was skipped in cross connection
uplink consideration. However, this ends up skipping more or less all
nl80211-based driver cases now since they mark the main interface P2P
capable. Relax this rule to allow the parent interface to be used as the
non-P2P station interface for cross connection purposes.

Signed-off-by: Jouni Malinen <j@w1.fi>
2014-12-10 01:54:27 +02:00
Jouni Malinen
97cfe110dc Clear wpa_s->disconnected on ctrl_iface FLUSH
This is needed to get into more consistent state after the FLUSH
command. DISCONNECT followed by FLUSH could result in
wpa_s->disconnected being left to 1 and this resulted in a test failure,
e.g., when running wpas_ctrl_dup_network followed by
wpas_ctrl_enable_disable_network where the latter was expecting
ENABLE_NETWORK on a disabled network to connect automatically and that
does not happen if wpa_s->disconnected == 1.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2014-12-08 16:22:13 +02:00
Jouni Malinen
aaadd72733 Check os_snprintf() result more consistently - more checks
Add more os_snprintf() result validation checks.

Signed-off-by: Jouni Malinen <j@w1.fi>
2014-12-08 11:42:07 +02:00
Jouni Malinen
1d39977136 Check os_snprintf() result more consistently
While these are using practically large enoungh buffer sizes, it is
better to be more consistent with checking os_snprintf() return value.

Signed-off-by: Jouni Malinen <j@w1.fi>
2014-12-08 11:42:07 +02:00
Jouni Malinen
1f102d3bb0 Check os_snprintf() result more consistently - manual
This converts os_snprintf() result validation cases to use
os_snprintf_error() for cases that were note covered by spatch and
semantic patches.

Signed-off-by: Jouni Malinen <j@w1.fi>
2014-12-08 11:42:07 +02:00
Jouni Malinen
eeab4f2fda Check os_snprintf() result more consistently - automatic 3
This converts os_snprintf() result validation cases to use
os_snprintf_error() where the comparison was 'res > size' instead of
'res >= size - 1'. These changes were done automatically with spatch
using the following semantic patch:

@@
identifier E1;
expression E2,E3,E4,E5,E6;
statement S1;
@@

(
  E1 = os_snprintf(E2, E3, ...);
|
  int E1 = os_snprintf(E2, E3, ...);
|
  if (E5)
	E1 = os_snprintf(E2, E3, ...);
  else
	E1 = os_snprintf(E2, E3, ...);
|
  if (E5)
	E1 = os_snprintf(E2, E3, ...);
  else if (E6)
	E1 = os_snprintf(E2, E3, ...);
  else
	E1 = 0;
|
  if (E5) {
	...
	E1 = os_snprintf(E2, E3, ...);
  } else {
	...
	return -1;
  }
|
  if (E5) {
	...
	E1 = os_snprintf(E2, E3, ...);
  } else if (E6) {
	...
	E1 = os_snprintf(E2, E3, ...);
  } else {
	...
	return -1;
  }
|
  if (E5) {
	...
	E1 = os_snprintf(E2, E3, ...);
  } else {
	...
	E1 = os_snprintf(E2, E3, ...);
  }
)
? os_free(E4);
- if (E1 < 0 || (size_t) E1 >= E3 - 1)
+ if (os_snprintf_error(E3, E1))
(
  S1
|
{ ... }
)

Signed-off-by: Jouni Malinen <j@w1.fi>
2014-12-08 11:42:07 +02:00
Jouni Malinen
7bdd8981f7 Check os_snprintf() result more consistently - automatic 2
This converts os_snprintf() result validation cases to use
os_snprintf_error() where the comparison was 'res > size' instead of
'res >= size'. These changes were done automatically with spatch using
the following semantic patch:

@@
identifier E1;
expression E2,E3,E4,E5,E6;
statement S1;
@@

(
  E1 = os_snprintf(E2, E3, ...);
|
  int E1 = os_snprintf(E2, E3, ...);
|
  if (E5)
	E1 = os_snprintf(E2, E3, ...);
  else
	E1 = os_snprintf(E2, E3, ...);
|
  if (E5)
	E1 = os_snprintf(E2, E3, ...);
  else if (E6)
	E1 = os_snprintf(E2, E3, ...);
  else
	E1 = 0;
|
  if (E5) {
	...
	E1 = os_snprintf(E2, E3, ...);
  } else {
	...
	return -1;
  }
|
  if (E5) {
	...
	E1 = os_snprintf(E2, E3, ...);
  } else if (E6) {
	...
	E1 = os_snprintf(E2, E3, ...);
  } else {
	...
	return -1;
  }
|
  if (E5) {
	...
	E1 = os_snprintf(E2, E3, ...);
  } else {
	...
	E1 = os_snprintf(E2, E3, ...);
  }
)
? os_free(E4);
- if (E1 < 0 || \( E1 > E3 \| (size_t) E1 > E3 \| E1 > (int) E3 \))
+ if (os_snprintf_error(E3, E1))
(
  S1
|
{ ... }
)

Signed-off-by: Jouni Malinen <j@w1.fi>
2014-12-08 11:42:07 +02:00
Jouni Malinen
d85e1fc8a5 Check os_snprintf() result more consistently - automatic 1
This converts os_snprintf() result validation cases to use
os_snprintf_error() where the exact rule used in os_snprintf_error() was
used. These changes were done automatically with spatch using the
following semantic patch:

@@
identifier E1;
expression E2,E3,E4,E5,E6;
statement S1;
@@

(
  E1 = os_snprintf(E2, E3, ...);
|
  int E1 = os_snprintf(E2, E3, ...);
|
  if (E5)
	E1 = os_snprintf(E2, E3, ...);
  else
	E1 = os_snprintf(E2, E3, ...);
|
  if (E5)
	E1 = os_snprintf(E2, E3, ...);
  else if (E6)
	E1 = os_snprintf(E2, E3, ...);
  else
	E1 = 0;
|
  if (E5) {
	...
	E1 = os_snprintf(E2, E3, ...);
  } else {
	...
	return -1;
  }
|
  if (E5) {
	...
	E1 = os_snprintf(E2, E3, ...);
  } else if (E6) {
	...
	E1 = os_snprintf(E2, E3, ...);
  } else {
	...
	return -1;
  }
|
  if (E5) {
	...
	E1 = os_snprintf(E2, E3, ...);
  } else {
	...
	E1 = os_snprintf(E2, E3, ...);
  }
)
? os_free(E4);
- if (E1 < 0 || \( E1 >= E3 \| (size_t) E1 >= E3 \| (unsigned int) E1 >= E3 \| E1 >= (int) E3 \))
+ if (os_snprintf_error(E3, E1))
(
  S1
|
{ ... }
)

Signed-off-by: Jouni Malinen <j@w1.fi>
2014-12-08 11:42:07 +02:00
Jouni Malinen
a80ba67a26 Check os_snprintf() result more consistently - success case
This converts os_snprintf() result validation cases to use
os_snprintf_error() in cases where success condition was used to execute
a step. These changes were done automatically with spatch using the
following semantic patch:

@@
expression E1,E2,E3;
statement S1;
@@

  E1 = os_snprintf(E2, E3, ...);
- if (\( E1 >= 0 \| E1 > 0 \) && \( (size_t) E1 < E3 \| E1 < (int) E3 \| E1 < E3 \))
+ if (!os_snprintf_error(E3, E1))
  S1

Signed-off-by: Jouni Malinen <j@w1.fi>
2014-12-08 11:42:07 +02:00
Jouni Malinen
a9aaacbb50 Check os_snprintf() result more consistently - maximum length
This adds verification of os_snprintf() result against the maximum
buffer length. These changes were done automatically with spatch
using the following semantic patch:

@@
expression E1,E2,E3;
statement S1;
@@

  E1 = os_snprintf(E2, E3, ...);
- if (\( E1 < 0 \| E1 <= 0 \))
+ if (os_snprintf_error(E3, E1))
(
  S1
|
{ ... }
)

Signed-off-by: Jouni Malinen <j@w1.fi>
2014-12-08 11:42:07 +02:00
Jouni Malinen
faebdeaa9e Use os_calloc() instead of os_zalloc()
Automatic changes with spatch using the following semantic patch:

@@
constant C;
type T;
@@

- os_zalloc(C*sizeof(T))
+ os_calloc(C,sizeof(T))

@@
expression E;
type T;
@@

- os_zalloc((E)*sizeof(T))
+ os_calloc(E,sizeof(T))

Signed-off-by: Jouni Malinen <j@w1.fi>
2014-12-08 11:42:07 +02:00
Jouni Malinen
c054190603 Fix DUP_NETWORK debug print on error case
Incorrect network id was printed in debug output if DUP_NETWORK
destination network was not found.

Signed-off-by: Jouni Malinen <j@w1.fi>
2014-12-08 11:42:07 +02:00
Jouni Malinen
49328f0756 Remove unnecessary ctrl_iface command check
MESH_GROUP_REMOVE always passes in the cmd pointer, so this cannot
really be NULL.

Signed-off-by: Jouni Malinen <j@w1.fi>
2014-12-08 11:42:06 +02:00
Jouni Malinen
d02dcb28bc Remove unnecessary ctrl_iface cmd check
This pointer cannot be NULL sicne it is called only from this file and
with a valid pointer to the received command.

Signed-off-by: Jouni Malinen <j@w1.fi>
2014-12-08 11:07:56 +02:00
Jouni Malinen
d84416a2af Interworking: Make bounds checking easier for static analyzers
'num * 5 > end - pos' handles bounds checking a bit more efficiently,
but apparently that is not clear enough for all static analyzers.
Replace with 'num > left / 5' to avoid false reports. (CID 68117)

Signed-off-by: Jouni Malinen <j@w1.fi>
2014-12-06 19:25:14 +02:00
Jouni Malinen
8105821b39 Replace send_ft_action() driver_op with send_action()
This reduced number of unnecessarily duplicated driver interface
callback functions for sending Action frames by using the more generic
send_action() instead of FT specific send_ft_action().

Signed-off-by: Jouni Malinen <j@w1.fi>
2014-12-06 18:13:29 +02:00
Jouni Malinen
bc0ba01d70 WFD: Allow WFD_SUBELEM_SET/GET all to be used with full IE buffer
This extends the previously used WFD_SUBELEM_SET/GET <subelem id> design
to allow special "all" value to be used as an id to indicate that all
WFD subelements are to be set/get. This uses similar interface as was
previously added over D-Bus.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2014-12-05 15:22:33 +02:00
Jouni Malinen
f80936094e WMM-AC: Use DEBUG verbosity for ignoring Action frame messages
There is no point in flooding the log with WARNING or ERROR level
messages if WMM-AC related Action frames are ignored in cases where they
were not expected. In addition, WARNING/ERROR should not really be used
in cases an invalid frame is dropped especially if this is not related
to a security setup since external devices could otherwise generate log
entries.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2014-12-05 13:17:57 +02:00
Jouni Malinen
0570a3ea7d HS 2.0: Clarify OSU Provider list length validation
The previous version was somewhat too complex for some static analyzers.
Use local variables for the extracted length fields and explicitly
compare these against the remaining buffer length. (CID 68121)

Signed-off-by: Jouni Malinen <j@w1.fi>
2014-12-05 00:56:05 +02:00
Jouni Malinen
65d9a5e254 ERP: Add wpa_supplicant ERP_FLUSH ctrl_iface command
This can be used to flush all the ERP keys.

Signed-off-by: Jouni Malinen <j@w1.fi>
2014-12-04 12:16:29 +02:00
Jouni Malinen
02a8d45ace ERP: Add support for ERP on EAP peer
Derive rRK and rIK on EAP peer if ERP is enabled. The new wpa_supplicant
network configuration parameter erp=1 can now be used to configure the
EAP peer to derive EMSK, rRK, and rIK at the successful completion of an
EAP authentication method. This functionality is not included in the
default build and can be enabled with CONFIG_ERP=y.

If EAP authenticator indicates support for re-authentication protocol,
initiate this with EAP-Initiate/Re-auth and complete protocol when
receiving EAP-Finish/Re-auth.

Signed-off-by: Jouni Malinen <j@w1.fi>
2014-12-04 12:16:29 +02:00
Dmitry Shmidt
f34891a3af Return only full network line in list_networks
It makes more sense to truncate at line boundary especially with the new
LAST_ID parameter.

Signed-off-by: Dmitry Shmidt <dimitrysh@google.com>
2014-12-03 22:31:53 +02:00
Vinit Deshpande
90903a77ef List all networks despite message limit of 4096 bytes
This change creates 'LIST_NETWORK LAST_ID=x' form to allow
retrieval of all networks saved in the system. Without this form,
only first few (whatever fills in first 4096 bytes) can be
retrieved.

Signed-off-by: Vinit Deshpande <vinitd@google.com>
2014-12-02 23:47:27 +02:00
Jouni Malinen
44177b69e8 Allow a BSS entry with all-zeros BSSID to expire
wpa_bss_in_use() used to determine that a BSS with BSSID of
00:00:00:00:00:00 is in use in almost every case since either
wpa_s->bssid or wpa_s->pending_bssid was likely to be cleared. This
could result in a corner case of a BSS entry remaining in the BSS table
indefinitely if one was added there with a (likely bogus) address of
00:00:00:00:00:00. Fix this by ignore wpa_s->bssid and
wpa_s->pending_bssid if the BSSID in the BSS table entry is
00:00:00:00:00:00.

In theory, that address is a valid BSSID, but it is unlikely to be used
in any production AP, so the potential expiration of a BSS entry with
that address during a connection attempt would not be a concern
(especially when a new scan would be enough to recover from that).

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2014-12-02 19:46:58 +02:00
Jouni Malinen
e374522827 Do not start new radio work on scan completion during ext work
Externally triggered scan could result in a new radio work item getting
started even when external radio work was in progress. Delay such start
until the external work is completed.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2014-12-01 20:17:08 +02:00
Jouni Malinen
4f9a5ea5cc WPS: Fix current_ssid clearing on duplicate network removal
It was possible for the current network profile to be deleted when
merging duplicated WPS credentials. However, this did not clear
wpa_s->current_ssid and it was possible for something else to end up
dereferencing that pointer to now freed memory. This could be hit, e.g.,
with ap_wps_mixed_cred. Fix this by clearing current_ssid also in this
code path similarly to other cases of network block getting removed.

Signed-off-by: Jouni Malinen <j@w1.fi>
2014-11-30 15:53:11 +02:00
Jouni Malinen
e4a35f07d9 mesh: Skip fast-association when using connect_without_scan
The mesh group addition was designed to use wpa_s->connect_without_scan
to skip a scan. That path was skipped if wpa_supplicant_fast_associate()
allowed previous scan results to be used. This could result in undesired
double-initialization attempt for the mesh interface. Avoid this by not
using wpa_supplicant_fast_associate() when wpa_s->connect_without_scan
is set.

Signed-off-by: Jouni Malinen <j@w1.fi>
2014-11-30 15:53:11 +02:00
Jouni Malinen
608b0ff52a mesh: Check for initialization failures
It is possible that these location ended up getting called before mesh
startup operations had been completed and that could result in
dereferencing NULL pointers. Address those error cases by verifying that
the needed parameters are available before using them.

Signed-off-by: Jouni Malinen <j@w1.fi>
2014-11-30 15:53:11 +02:00
Jouni Malinen
9a700ff9ef Ignore auth/assoc timeout events in mesh configuration
It was possible for auth/assoc timeout/failure event from the driver to
result in unexpected processing during mesh group setup if that
operation was started before the previously started driver operation to
association/connect had completed. Since those events cannot happen in
mesh cases, ignore them to avoid issues due to this corner case.

For example, monitor_iface_unknown_sta followed by wpas_mesh_secure test
case resulted in failure without this change.

Signed-off-by: Jouni Malinen <j@w1.fi>
2014-11-30 15:53:11 +02:00
Jouni Malinen
763041b2e8 mesh: Avoid a false maybe-uninitialized compiler warning
An earlier check of the action_field value above the switch statement
already took care of all other possible cases, but that was apparently
too difficult for the compiler to notice. Bring back the default case to
avoid incorrect warnings about the event variable being maybe
uninitialized.

Signed-off-by: Jouni Malinen <j@w1.fi>
2014-11-30 15:53:11 +02:00
Jouni Malinen
c932b43e56 mesh: Add more debug information to MPM Action frame processing
This makes it easier to figure out why a peering message is dropped.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2014-11-28 23:02:29 +02:00
Jouni Malinen
fc0ef7c0e7 Add DATA_TEST_FRAME for testing Data frame processing
The new wpa_supplicant control interface command can be used in
automated testing to verify how AP processes Data frames with arbitrary
contents. This is enabled only in builds with CONFIG_TESTING_OPTIONS=y.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2014-11-27 23:51:46 +02:00
Jouni Malinen
b925506a91 Clear RSN preauth and PMKSA cache state on FLUSH command
There is no need for this state to maintained when the wpa_supplicant
FLUSH ctrl_iface command is used to request flushing of all state.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2014-11-27 19:56:15 +02:00
Jouni Malinen
3882a70841 WMM AC: Fix memory leak on deinit without disassoc event
It was possible for wmm_ac_deinit() not getting called when an interface
was removed in a sequence where disassociation was not reported and
wmm_ac_notify_disassoc() did not get called. This resulted in leaking
whatever memory was allocated for WMM AC parameters. Fix that by calling
wmm_ac_notify_disassoc() from wpa_supplicant_cleanup().

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2014-11-27 19:00:02 +02:00
Jouni Malinen
5214f4fafc Clear scan_req to NORMAL_SCAN_REQ for connection attempt
This is needed to fix some sequencies where a real scan in ap_scan=2
case would be issued even when the connection case would expect direct
connection without a scan.

This fixed an issue shown in hwsim test case autoscan_exponential
followed by ibss_open_fixed_bssid.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2014-11-27 17:55:54 +02:00
Jouni Malinen
4e0990dc88 mesh: Send peering close message before leaving mesh
This is needed to allow proper Action frame transmission to work without
having to claim these to be offchannel operations.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2014-11-27 17:12:47 +02:00
Neelansh Mittal
3a7414b6a6 Do not re-open Android control sockets
On Android, the control socket being used may be the socket that is
created when wpa_supplicant is started as a /init.*.rc service. Such a
socket is maintained as a key-value pair in Android's environment.
Closing this control socket would leave wpa_supplicant in a bad state.
When wpa_supplicant re-opens the ctrl_iface socket, it will query the
Android's environment, and will be returned with the same socket
descriptor that has already been closed.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2014-11-25 17:16:44 +02:00
Masashi Honma
a959a3b69d SAE: Fix Anti-Clogging Token request frame format
This commit inserts Finite Cyclic Group to Anti-Clogging Token request
frame because IEEE Std 802.11-2012, Table 8-29 says "Finite Cyclic Group
is present if Status is zero or 76".

Signed-off-by: Masashi Honma <masashi.honma@gmail.com>
2014-11-25 16:08:53 +02:00
Jouni Malinen
849367afe9 SME: Fix a sign-compare warning
Signed-off-by: Jouni Malinen <j@w1.fi>
2014-11-25 01:07:16 +02:00
Jouni Malinen
158211b2db WNM: Use country code, if available, to help in channel mapping
The country code from the current AP needs to be used in
ieee80211_chan_to_freq() to support cases where non-global operating
class table is used.

Signed-off-by: Jouni Malinen <j@w1.fi>
2014-11-24 10:57:38 +02:00
Jouni Malinen
5d017065a0 GAS: Clean up Query Response length validation
Previous version was correct, but apparently too complex for some static
analyzers. (CID 68119)

Signed-off-by: Jouni Malinen <j@w1.fi>
2014-11-23 21:03:40 +02:00
Jouni Malinen
355e17eb1b HS 2.0: Clarify OSU Server URI length validation
The previous version was valid, but apparently too complex for some
static analyzers. Use a local variable for uri_len and explicitly
compare it against the remaining buffer length. (CID 68121)

Signed-off-by: Jouni Malinen <j@w1.fi>
2014-11-23 21:03:40 +02:00
Jouni Malinen
5c58c0ce86 HS 2.0: More explicit hs20_osu_icon_fetch() length validation
The previous version was fine, but too much for some static analyzers to
understand as proper bounds checking. (CID 68122)

Signed-off-by: Jouni Malinen <j@w1.fi>
2014-11-23 21:03:40 +02:00
Jouni Malinen
fecc09edc3 WNM: Use a clearer validation step for key_len_total
The previous one based on pointer arithmetic was apparently too much for
some static analyzers (CID 68130).

Signed-off-by: Jouni Malinen <j@w1.fi>
2014-11-23 18:04:02 +02:00
Jouni Malinen
43aee94899 Interworking: Clearer ANQP element length validation
The upper bound for the element length was already verified, but that
was not apparently noticed by a static analyzer (CID 68128).

Signed-off-by: Jouni Malinen <j@w1.fi>
2014-11-23 17:41:13 +02:00
Jouni Malinen
f5f3728a81 WNM: Print debug message if Action frame sending fails
This makes wpa_drv_send_action() return value checking more consistent
(CID 75390).

Signed-off-by: Jouni Malinen <j@w1.fi>
2014-11-23 16:13:50 +02:00
Andrei Otcheretianski
70d1e72849 wpa_supplicant: Handle link measurement requests
Send link measurement response when a request is received. Advertise
only RCPI, computing it from the RSSI of the request. The TX power field
is left to be filled by the driver. All other fields are not published.

Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
2014-11-22 21:45:07 +02:00
Assaf Krauss
66d2143435 wpa_cli: Add optional ssid to neighbor report request
Add optional 'ssid' parameter to command "neighbor_rep_request".

Signed-off-by: Assaf Krauss <assaf.krauss@intel.com>
2014-11-22 21:37:49 +02:00
Assaf Krauss
4c4b230527 wpa_supplicant: Add an option to specify SSID in neighbor report requests
Allow supplying an SSID for the SSID IE. If not supplied, no SSID IE is
sent, and the request implies the current SSID.

Signed-off-by: Assaf Krauss <assaf.krauss@intel.com>
2014-11-22 21:36:42 +02:00
Assaf Krauss
fad14af93a wpa_cli: Add neighbor_rep_request command
Add neighbor_rep_request command to send a Neighbor Report Request
to the associated AP.

Signed-off-by: Assaf Krauss <assaf.krauss@intel.com>
2014-11-22 21:29:41 +02:00
Assaf Krauss
f4b8bfae15 wpa_supplicant: Add NEIGHBOR_REP_REQUEST command to the control interface
Add NEIGHBOR_REP_REQUEST command to the wpa_supplicant ctrl_iface.
This command triggers the sending of a Neighbor Report Request to the
associated AP.

Signed-off-by: Assaf Krauss <assaf.krauss@intel.com>
2014-11-22 21:28:52 +02:00
Assaf Krauss
d89c0701db wpa_supplicant: Add support for Neighbor Report
Add the ability to send a Neighbor Report Request (part of
RRM). Requester is then notified once the report arrives.

Signed-off-by: Assaf Krauss <assaf.krauss@intel.com>
2014-11-22 21:23:14 +02:00
Assaf Krauss
b361d580ec SME: Add RRM support to association request
In case the AP we are associating with advertises support for RRM,
advertise our own RRM support in the (Re)Association Request frame. This
is done by adding an RRM Capabilities IE. The underlying driver is
expected to further add a Power Capabilities IE to the request, and set
the Radio Measurement flag in the Capability Info field. At this point
the RRM Capabilities IE advertises no measurement support.

Signed-off-by: Assaf Krauss <assaf.krauss@intel.com>
2014-11-22 21:13:45 +02:00
Assaf Krauss
f936b73c4f wpa_supplicant: Store driver's RRM capabilities
Store the RRM capability flags reported by the underlying driver.

Signed-off-by: Assaf Krauss <assaf.krauss@intel.com>
2014-11-22 21:07:56 +02:00
Jouni Malinen
75d65857d5 WNM: Use recent scan results on BSS transition request
If the last scans are recent (for now, less than ten seconds old), use
them instead of triggering a new scan when a BSS Transition Management
Request frame is received. As a fallback, allow a new scan to be
triggered if no matches were found.

Signed-off-by: Jouni Malinen <j@w1.fi>
2014-11-22 20:17:47 +02:00
Jouni Malinen
e1117c1c01 WNM: Optimize BSS transition management scans
When the list of preferred transition candidates is received, use the
identified channels to optimize the following scan so that no time is
wasted on other channels.

Signed-off-by: Jouni Malinen <j@w1.fi>
2014-11-22 20:17:47 +02:00
Jouni Malinen
d0b9ab69f6 WNM: Move transition candidate list processing to normal scan
This makes it easier to optimize transition request processing.

Signed-off-by: Jouni Malinen <j@w1.fi>
2014-11-22 18:40:03 +02:00
Jouni Malinen
279b5486a6 WNM: Fix TM candidate freeing if multiple requests are processed
The previously cached candidate list needs to be free properly through a
call to wnm_deallocate_memory() to ensure all subelements gets freed.

Signed-off-by: Jouni Malinen <j@w1.fi>
2014-11-22 18:40:03 +02:00
Jouni Malinen
027454d2e9 WNM: Allow BSS transition request in same ESS even if RSSI is worse
This allows an AP to steer us to another BSS within the ESS even if that
results in reduced signal strength as long as the signal strength with
the target BSS is expected to provide some connectivity.

Signed-off-by: Jouni Malinen <j@w1.fi>
2014-11-22 18:06:37 +02:00
Jouni Malinen
6900b6d96f WNM: Mark wnm_scan_response() static
This function is not used outside wnm_sta.c.

Signed-off-by: Jouni Malinen <j@w1.fi>
2014-11-22 18:06:37 +02:00
Jouni Malinen
ff2c5758bb WNM: Order BSS transmission candidate entries based on preference
Signed-off-by: Jouni Malinen <j@w1.fi>
2014-11-22 18:06:37 +02:00
Jouni Malinen
093226783d WNM: Simplify how candidate subelements are stored
There is no need to use a separately allocated data structures for this.
A bitfield indicating which information is present and variables within
struct neighbor_report are simpler to use and more efficient.

Signed-off-by: Jouni Malinen <j@w1.fi>
2014-11-22 18:06:37 +02:00
Jouni Malinen
8c9af762f3 WNM: Calculate valid-until time for transition candidate list
This is of more use than the raw validity interval (number of beacon
intervals) that was recorded previously.

Signed-off-by: Jouni Malinen <j@w1.fi>
2014-11-22 18:06:27 +02:00
Jouni Malinen
4c381f0d1c WNM: Convert BSSID Info into a u32
This is more convenient to use than u8 array.

Signed-off-by: Jouni Malinen <j@w1.fi>
2014-11-22 17:03:15 +02:00
Jouni Malinen
8040dc53c2 WNM: Debug print WNM BSS Transition Candidate List
Signed-off-by: Jouni Malinen <j@w1.fi>
2014-11-22 16:34:34 +02:00
Thomas Pedersen
9e5e03d77e Add examples of new mesh options into wpa_supplicant.conf
Signed-off-by: Javier Lopez <jlopex@gmail.com>
Signed-off-by: Jason Mobarak <x@jason.mobarak.name>
Signed-off-by: Thomas Pedersen <thomas@noack.us>
2014-11-20 16:31:09 +02:00
Johannes Berg
83b9d426e0 WMM AC: Notify driver before sending DelTS
Switch the stop and sending DelTS to avoid sending data packets
for the session after the DelTS, which is otherwise possible.

This also helps the mac80211 implementation as it requires stopping the
traffic flow before sending the DelTS as it may modify the AC parameters
for the affected queue, and that may in turn affect management frames.

Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2014-11-16 21:40:57 +02:00
Moshe Benji
8506ea6f17 WMM AC: Add wmm_ac_status control interface command
This wmm_ac_status command will show the current status for WMM AC.

Signed-off-by: Moshe Benji <moshe.benji@intel.com>
Signed-off-by: Eliad Peller <eliad@wizery.com>
2014-11-16 21:40:51 +02:00
Moshe Benji
df9d340c80 wpa_cli: WMM_AC_ADDTS and WMM_AC_DELTS commands
wmm_ac_addts command will add (or update) a traffic stream and
wmm_ac_delts command will delete an existing traffic stream.

Each of the above commands will call its corresponding
ctrl_iface command.

Signed-off-by: Moshe Benji <moshe.benji@intel.com>
Signed-off-by: Eliad Peller <eliad@wizery.com>
2014-11-16 21:16:03 +02:00
Moshe Benji
eb2f2088aa ctrl_iface: Add wmm_ac_addts and wmm_ac_delts commands
wmm_ac_addts command will add (or update) a traffic stream and
wmm_ac_delts command will delete an existing traffic stream.

Signed-off-by: Moshe Benji <moshe.benji@intel.com>
Signed-off-by: Eliad Peller <eliad@wizery.com>
2014-11-16 21:13:42 +02:00
Moshe Benji
d1f880013a WMM AC: Handle TSPEC action frames
Add the TSPEC to the driver on successful TSPEC ADDTS response. Delete
the TSPEC when receiving DELTS action.

Signed-off-by: Moshe Benji <moshe.benji@intel.com>
Signed-off-by: Eliad Peller <eliad@wizery.com>
2014-11-16 21:07:08 +02:00
Eliad Peller
674f6c073f WMM AC: Add basic ADDTS/DELTS sending functions
Add basic implementation for ADDTS and DELTS sending
functions.

wpas_wmm_ac_addts() will send ADDTS request public action,
containing TSPEC (traffic stream specification) with
the given params.

wpas_wmm_ac_delts() will look for the saved tspec with
the given tid, and send DELTS public action for it.

(Handling of ADDTS response and actually configuring the admission
control params will be added in following patches.)

Signed-off-by: Moshe Benji <moshe.benji@intel.com>
Signed-off-by: Eliad Peller <eliad@wizery.com>
2014-11-16 21:03:56 +02:00
Moshe Benji
471cd6e10c WMM AC: Add add_tx_ts and del_tx_ts driver ops
Add add_tx_ts() and del_tx_ts() ops to notify the driver about
TSPEC add / delete.

Additionally, add wmm_ac_supported flag to indicate
whether the driver supports WMM AC.

Signed-off-by: Moshe Benji <moshe.benji@intel.com>
Signed-off-by: Eliad Peller <eliad@wizery.com>
2014-11-16 20:47:36 +02:00
Moshe Benji
a0413b1734 WMM AC: Parse WMM IE on association
Initialize WMM AC data structures upon successful association
with an AP that publishes WMM support, and deinitialize the data
structure when the association is no longer valid.

Signed-off-by: Moshe Benji <moshe.benji@intel.com>
Signed-off-by: Eliad Peller <eliadx.peller@intel.com>
2014-11-16 20:47:34 +02:00
Masashi Honma
e609679984 mesh: Make plink params configurable
This patch makes four MIB variables for plink configurable and sets the
correct default values based on IEEE Std 802.11s-2011.

Signed-off-by: Masashi Honma <masashi.honma@gmail.com>
2014-11-16 19:43:11 +02:00
Masashi Honma
0c6099f31b mesh: Check mesh key management method
Signed-off-by: Natsuki Itaya <Natsuki.Itaya@jp.sony.com>
Signed-off-by: Masashi Honma <masashi.honma@gmail.com>
2014-11-16 19:43:11 +02:00
Masashi Honma
44a1662a50 mesh: Add wpa_cli action script processing for mesh events
Signed-off-by: Natsuki Itaya <Natsuki.Itaya@jp.sony.com>
Signed-off-by: Masashi Honma <masashi.honma@gmail.com>
2014-11-16 19:43:11 +02:00
Masashi Honma
790709060d mesh: Add scan result for mesh network
Android 4.4 uses "BSS" command instead of "SCAN_RESULT" command.
So this patch add the mesh scan result for BSS command.

Signed-off-by: Masashi Honma <masashi.honma@gmail.com>
2014-11-16 19:43:11 +02:00
Masashi Honma
2b2bb5a8b9 mesh: Make BSSBasicRateSet configurable
STAs that have different BSSBasicRateSet cannot connect to each other
as per IEEE 802.11s-2011 9.6.0c1:

"A mesh STA shall not establish a mesh peering with a mesh STA using a
different BSSBasicRateSet."

Make BSSBasicRateSet configurable to improve interoperability with other
stations.

Signed-off-by: Masashi Honma <masashi.honma@gmail.com>
2014-11-16 19:43:11 +02:00
Javier Lopez
603a3f34c4 Add mesh_group_{add,remove} control interface commands
Parse MESH_GROUP_ADD/REMOVE commands on ctrl interface and call
wpa_supplicant routines. These commands are used to start or
join and leave a mesh network.

The mesh id is given in the configuration file, therefore there is
no need to scan before joining a mesh network. We reuse the
connect_without_scan construct used by P2P for that same purpose.

Signed-off-by: Javier Cardona <javier@cozybit.com>
Signed-off-by: Javier Lopez <jlopex@gmail.com>
2014-11-16 19:43:11 +02:00
Masashi Honma
798b318223 mesh: Reduce none 11N Self-protected Action frame allocation size
Signed-off-by: Natsuki Itaya <Natsuki.Itaya@jp.sony.com>
Signed-off-by: Masashi Honma <masashi.honma@gmail.com>
2014-11-16 19:43:11 +02:00
Masashi Honma
9204e73831 mesh: Fix 11N capability in Self-protected Action frame
mesh_ht_mode default value is CHAN_UNDEFINED.
So previous code set 11N capability even though 11N is not used.

Signed-off-by: Natsuki Itaya <Natsuki.Itaya@jp.sony.com>
Signed-off-by: Masashi Honma <masashi.honma@gmail.com>
2014-11-16 19:43:11 +02:00
Masashi Honma
edfefaed3c mesh: Set driver capability flags to mesh interface
Signed-off-by: Kenzoh Nishikawa <Kenzoh.Nishikawa@jp.sony.com>
Signed-off-by: Masashi Honma <masashi.honma@gmail.com>
2014-11-16 19:43:11 +02:00
Masashi Honma
eac0231642 mesh: Fix segmentation fault by repeating MESH_GROUP_ADD/REMOVE
Signed-off-by: Natsuki Itaya <Natsuki.Itaya@jp.sony.com>
Signed-off-by: Masashi Honma <masashi.honma@gmail.com>
2014-11-16 19:43:11 +02:00
Jason Mobarak
5cfb672dde mesh: Enable mesh HT mode
Add a new option "mesh_ht_mode" that specifies the HT mode for the
mesh, with this option on, mesh beacons, actions frames, and probe
responses with include the appropriate HT information elements.

[original implementation by Chun-Yeow Yeoh <yeohchunyeow@gmail.com>]
[some fixes by Masashi Honma <masashi.honma@gmail.com>]
Signed-off-by: Ashok Nagarajan <ashok.dragon@gmail.com>
Signed-off-by: Javier Cardona <javier@cozybit.com>
Signed-off-by: Jason Mobarak <x@jason.mobarak.name>
2014-11-16 19:43:11 +02:00
Chun-Yeow Yeoh
c596f3f083 mesh: Add timer for SAE authentication in RSN mesh
Add timer to do SAE re-authentication with number of tries defined
by MESH_AUTH_RETRY and timeout defined by MESH_AUTH_TIMEOUT.

Ignoring the sending of reply message on "SAE confirm before commit"
to avoid "ping-pong" issues with other mesh nodes. This is obvious when
number of mesh nodes in MBSS reaching 6.

Signed-off-by: Chun-Yeow Yeoh <yeohchunyeow@gmail.com>
Signed-off-by: Bob Copeland <me@bobcopeland.com>
2014-11-16 19:43:11 +02:00
Thomas Pedersen
0f950df029 mesh: Add mesh robust security network
This implementation provides:

- Mesh SAE authentication mechanism
- Key management (set/get PSK)
- Cryptographic key establishment
- Enhanced protection mechanisms for robust management frames

Signed-off-by: Javier Lopez <jlopex@gmail.com>
Signed-off-by: Javier Cardona <javier@cozybit.com>
Signed-off-by: Jason Mobarak <x@jason.mobarak.name>
Signed-off-by: Thomas Pedersen <thomas@noack.us>
2014-11-16 19:43:06 +02:00
Dmitry Shmidt
88cb27c7a5 hostapd: Add wowlan_triggers config param
New kernels in wiphy_suspend() will call cfg80211_leave_all() that will
eventually end up in cfg80211_stop_ap() unless wowlan_triggers were set.
For now, use the parameters from the station mode as-is. It may be
desirable to extend (or constraint) this in the future for specific AP
mode needs.

Signed-off-by: Dmitry Shmidt <dimitrysh@google.com>
2014-11-16 17:09:11 +02:00
Jouni Malinen
087a1f4efd Suite B: PMKID derivation for AKM 00-0F-AC:11
The new AKM uses a different mechanism of deriving the PMKID based on
KCK instead of PMK. hostapd was already doing this after the KCK had
been derived, but wpa_supplicant functionality needs to be moved from
processing of EAPOL-Key frame 1/4 to 3/4 to have the KCK available.

Signed-off-by: Jouni Malinen <j@w1.fi>
2014-11-16 17:09:11 +02:00
Jouni Malinen
666497c8e6 Suite B: Add AKM 00-0F-AC:11
This adds definitions for the 128-bit level Suite B AKM 00-0F-AC:11. The
functionality itself is not yet complete, i.e., this commit only
includes parts to negotiate the new AKM.

Signed-off-by: Jouni Malinen <j@w1.fi>
2014-11-16 13:20:51 +02:00
Dmitry Shmidt
d10792199e Add CTRL-EVENT-SCAN-FAILED notification in case of scan failure
This is needed since the SCAN command with radio work returns before the
actual driver operation to trigger a scan has been executed and as such,
cannot return result of that operation.

Signed-off-by: Dmitry Shmidt <dimitrysh@google.com>
2014-11-15 11:03:52 +02:00
Jouni Malinen
ee231fdb2b Remove completed to-do items
While this file has not really been updated in years, some of the
completed items can easily be removed.

Signed-off-by: Jouni Malinen <j@w1.fi>
2014-11-01 16:24:36 +02:00
Jouni Malinen
01b32d5e36 Remove references to madwifi from various files
Number of documentation and configuration files had references to the
madwifi driver interface that was removed in the previous commit. Remove
these references as well.

Signed-off-by: Jouni Malinen <j@w1.fi>
2014-11-01 16:15:53 +02:00
Slava Monich
c66f23491e dbus: Fix memory leak in wpas_dbus_getter_bss_wps
Signed-off-by: Slava Monich <slava.monich@jolla.com>
2014-11-01 15:56:14 +02:00
Martin Kletzander
6721909fb1 wpa_gui: Use dialog window type
This helps window managers treat the window properly. Mostly tiling WMs
are affected by this. All other windows inherit this option from QDialog
already.

Signed-off-by: Martin Kletzander <mkletzan@redhat.com>
2014-11-01 15:55:49 +02:00
Sunil Dutt
477b082cc4 P2P: Do not consider the p2p_scan results after p2p_stop_find
If p2p_stop_find is issued after the p2p_scan request is triggered to
the host driver, the obtained scan results are also considered to update
the P2P peer entries. This is not always desired behavior, i.e., it can
be clearer if no P2P-DEVICE-FOUND events are generated based of that
final pending scan.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2014-10-31 00:50:01 +02:00
Sunil Dutt
e7ce540239 P2P: Delay scan operation only when P2P is not in search state
With the radio work interface in place, station interface SCAN command
was not scheduled (i.e., it got continously delayed with "Delay station
mode scan while P2P operation is in progress") when a p2p_find was
operational. Fix this be delaying station mode scan only when a P2P
operation is in progress, but not in search state.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2014-10-31 00:49:14 +02:00
Sunil Dutt
b951a97454 P2P: Set p2p_scan_running based on driver scan request result
With the radio work interface, the actual request to start p2p_scan
operation is scheduled from a radio work and hence the initial return
value cannot provide the real result of the driver operation to trigger
a scan. Introduce a new notification API to indicate the scan trigger
status based on which the p2p_scan_running instance can be set using the
real return value from the driver operation.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2014-10-31 00:05:25 +02:00
Jouni Malinen
3586d55a5d P2P: Do not call wpas_p2p_disconnect_safely() if no match is found
In theory, wpas_p2p_disconnect_safely() could have dereferenced the
wpa_s == NULL argument, but in practice, it won't due to the
calling_wpa_s == wpa_s check and wpas_p2p_disconnect() accepting NULL.
Anyway, it is cleaner to add an explicit check for this. (CID 74492)

Signed-off-by: Jouni Malinen <j@w1.fi>
2014-10-28 01:50:22 +02:00
Jouni Malinen
a7f5271d52 Update pending connect radio work BSS pointer on scan update
It is possible for scan result processing or BSS entry removal to occur
while there is a pending connect or sme-connect radio work with a
previously selected BSS entry. The BSS pointer was previously verified
to be valid, i.e., still point to a BSS entry, at the time the actual
connection operation is started. However, that BSS entry could have
changed to point to another BSS if the old BSS entry was either removed
or reallocated and a new BSS entry was added at the same location in
memory. This could result in the connection attempt failing to configure
parameters properly due to different BSS information (e.g., different
BSSID).

Fix this by updated the pending connect radio work data on BSS entry
updates similarly to how the last_scan_res array was updated. If the
selected BSS entry is removed, this will still result in a failed
connection, but reallocated BSS entry is now followed properly and used
when the connection work starts.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2014-10-28 00:43:58 +02:00
Sunil Dutt
7465640066 Invoke connect work done for all the connection failure cases
This commit fixes couple of connection failure paths where
wpas_connect_work_done() was not called, thus enabling the radio work
interface to proceed with the other queued actions.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2014-10-27 20:19:35 +02:00
Jouni Malinen
76d81b3272 WPS: Fix ap_scan=2 special association case
Commit 22628eca34 ('Support driver-based
BSS selection in ap_scan=1 mode') ended up disabling the special
ap_scan=2 WPS case where ap_scan=1 like scan followed by association is
used to find the WPS AP using wildcard SSID. Fix this by allowing
association request even with wpas_driver_bss_selection() when searching
for a WPS AP.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2014-10-27 20:13:39 +02:00
Tomasz Bursztyka
745d62322b dbus: Redirect P2P request to the managment device if present
In case of a P2P management device being present, it will be up to that
interface to handle P2P requests.

Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
2014-10-27 17:15:09 +02:00
Tomasz Bursztyka
bb3df9a569 notify: Do not raise any signal from a P2P management interface
Such interface is not registered on DBus, thus there is no need to raise
any signal from it.

Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
2014-10-27 17:15:09 +02:00
Tomasz Bursztyka
21efc940f6 wpa_supplicant: Do not register a P2P management interface on DBus
DBus client should always request the proper netdev interface. This will
be necessary to get a consistent behavior whatever driver is in use:
iwlwifi (which requires a P2P mgmt dev), ath9/10k (which does not),
etc...

Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
2014-10-27 17:15:09 +02:00
Tomasz Bursztyka
5aa839c80b wpa_supplicant: Parent interface should know about its dedicated P2P dev
This will be useful to hand-off P2P commands from the parent interface
to its dedicated P2P device if that one is present, in DBus interface.

Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
2014-10-27 17:15:09 +02:00
Ahmad Masri
d77419d234 P2P: Support GCMP as part of 60 GHz support
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2014-10-27 17:15:09 +02:00
Jouni Malinen
bd43e67e59 Avoid unsigned vs. signed comparison warning
Signed-off-by: Jouni Malinen <j@w1.fi>
2014-10-26 17:01:37 +02:00
Ilan Peer
1170239efa P2P: Save group common frequencies in invitation result
Save the group common frequencies when starting a GO due to
an invitation signaling requesting to re-invoke a persistent GO.

To do so, move the code that handles the translation of p2p_channels to
frequency list into a public function so it can be re-used both when GO
Negotiation is done and invitation signaling is done.

Signed-off-by: Ilan Peer <ilan.peer@intel.com>
2014-10-26 01:24:28 +03:00
Ilan Peer
20beb96ff9 P2P: Save group common frequencies
Once a P2P GO interface is configured, save the group common
frequencies, as this can be useful later for channel selection
considerations during channel switch, etc.

Signed-off-by: Ilan Peer <ilan.peer@intel.com>
2014-10-26 01:24:13 +03:00
Ilan Peer
0a44358055 wpa_supplicant: Use the 'no_ir' notation
Use the 'no_ir' notation instead of the 'passive scan' and
'no_ibss' notations to match the earlier change in nl80211.

Signed-off-by: Ilan Peer <ilan.peer@intel.com>
2014-10-26 01:23:43 +03:00
Jouni Malinen
1f94e4ee3e Add test functionality to simulate driver increased ROC duration
The extra_roc_dur parameter can now be used in CONFIG_TESTING_OPTIONS=y
builds to simulate driver behavior where the ROC duration gets increased
without user space request.

Signed-off-by: Jouni Malinen <j@w1.fi>
2014-10-25 21:46:38 +03:00
Mikael Kanstrup
431dd8bb11 P2P: Use neg_freq when re-establish persistent group as GC
When GC receives invitation response and tries to re-establish
connection to a persistent group channels from passive list should
be allowed. A missing check for operation mode triggered reselection
of operating channel from active channels only to happen and thus fail
the connect attempt.

Add a check for operation mode and if GC instead use negotiated
frequency (i.e. GO operating channel from invitation response).

Signed-off-by: Mikael Kanstrup <mikael.kanstrup@sonymobile.com>
2014-10-25 18:52:22 +03:00
Jason Abele
fbca4c893d mesh: Implement mesh scanning
When mesh is configured in, include the wildcard mesh id so that mesh
networks are returned.

Signed-off-by: Javier Lopez <jlopex@gmail.com>
Signed-off-by: Jason Abele <jason.abele@gmail.com>
2014-10-25 17:45:35 +03:00
Jason Abele
d73b3f2ea0 mesh: Use mesh id instead of SSID in BSS table
Signed-off-by: Javier Lopez <jlopex@gmail.com>
Signed-off-by: Jason Abele <jason.abele@gmail.com>
2014-10-25 17:45:35 +03:00
Thomas Pedersen
07cb45ccb2 mesh: Add no_auto_peer config option
Add no_auto_peer parameter, which controls wheter a station will
automatically initiate peering to another mesh peer that comes into
range.

Signed-off-by: Javier Lopez <jlopex@gmail.com>
Signed-off-by: Jason Mobarak <x@jason.mobarak.name>
Signed-off-by: Thomas Pedersen <thomas@noack.us>
2014-10-25 17:45:35 +03:00
Thomas Pedersen
476e6bb68d mesh: Add mesh mode config option
Modify network mode to support mode number 5 when CONFIG_MESH is
enabled.

Signed-off-by: Javier Lopez <jlopex@gmail.com>
Signed-off-by: Jason Mobarak <x@jason.mobarak.name>
Signed-off-by: Thomas Pedersen <thomas@noack.us>
2014-10-25 17:45:35 +03:00
Thomas Pedersen
a3335ef518 mesh: Avoid join if already joined a mesh group
Signed-off-by: Javier Lopez <jlopex@gmail.com>
Signed-off-by: Thomas Pedersen <thomas@noack.us>
2014-10-25 17:45:35 +03:00
Bob Copeland
5f92659d88 mesh: Add mesh peering manager
The mesh peering manager establishes and maintains links among
mesh peers, tracking each peer link via a finite state machine.

This implementation supports open mesh peerings.

[assorted fixes from Yu Niiro <yu.niiro@gmail.com>]
[more fixes from Masashi Honma <masashi.honma@gmail.com>]
Signed-off-by: Javier Lopez <jlopex@gmail.com>
Signed-off-by: Javier Cardona <javier@cozybit.com>
Signed-off-by: Ashok Nagarajan <ashok.dragon@gmail.com>
Signed-off-by: Jason Mobarak <x@jason.mobarak.name>
Signed-hostap: Bob Copeland <me@bobcopeland.com>
2014-10-25 17:45:31 +03:00