Commit graph

4536 commits

Author SHA1 Message Date
Michal Privoznik
1b8ed2cac1 wpa_supplicant: Fix build with !CONFIG_AP and CONFIG_CTRL_IFACE_DBUS_NEW
If the CONFIG_CTRL_IFACE_DBUS_NEW is enabled but CONFIG_AP is
disabled the build fails. This is because dbus getters try to
access ap_iface member of wpa_supplicant struct which is defined
if and only if CONFIG_AP is enabled.

Signed-off-by: Michal Privoznik <mprivozn@redhat.com>
2018-12-31 11:41:26 +02:00
Jouni Malinen
948ba8c294 mka: MIB information
Provide MKA information through the wpa_supplicant control interface MIB
command.

Signed-off-by: Jouni Malinen <j@w1.fi>
2018-12-29 16:52:31 +02:00
Asbjørn Sloth Tønnesen
594b7fbdde wpa_supplicant: Document nl80211 driver in the man page
Signed-off-by: Asbjørn Sloth Tønnesen <hostap@asbjorn.st>
2018-12-27 16:03:46 +02:00
Jouni Malinen
7251f0badc mka: Extend CAK/CKN-from-EAP-MSK API to pass in MSK length
This can be used to allow 256-bit key hierarchy to be derived from
EAP-based authentication. For now, the MSK length is hardcoded to 128
bits, so the previous behavior is maintained.

Signed-off-by: Jouni Malinen <j@w1.fi>
2018-12-26 16:44:58 +02:00
Jouni Malinen
871439b5d5 mka: Allow 256-bit CAK to be configured for PSK mode
This allows 256-bit CAK to be used as the root key in the MKA key
hierarchy.

Signed-off-by: Jouni Malinen <j@w1.fi>
2018-12-26 16:44:58 +02:00
Andrey Kartashev
e49b78c0d5 mka: Allow configuration of MACsec replay protection
Add new configuration parameters macsec_replay_protect and
macsec_replay_window to allow user to set up MACsec replay protection
feature. Note that according to IEEE Std 802.1X-2010 replay protection
and delay protection are different features: replay protection is
related only to SecY and does not appear on MKA level while delay
protection is something that KaY can use to manage SecY state.

Signed-off-by: Andrey Kartashev <andrey.kartashev@afconsult.com>
2018-12-26 16:42:25 +02:00
Mike Siedzik
2fc0675683 mka: Fix lowest acceptable Packet Number (LPN) calculation and use
The purpose of the Lowest Acceptable PN (lpn) parameters in the MACsec
SAK Use parameter set is to enforce delay protection. Per IEEE Std
802.1X-2010, Clause 9, "Each SecY uses MKA to communicate the lowest PN
used for transmission with the SAK within the last two seconds, allowing
receivers to bound transmission delays."

When encoding the SAK Use parameter set the KaY should set llpn and olpn
to the lowest PN transmitted by the latest SAK and oldest SAK (if
active) within the last two seconds. Because MKPDUs are transmitted
every 2 seconds (MKA_HELLO_TIME), the solution implemented here
calculates lpn based on the txsc->next_pn read during the previous MKPDU
transmit.

Upon receiving and decoding a SAK Use parameter set with delay
protection enabled, the KaY will update the SecY's lpn if the delay
protect lpn is greater than the SecY's current lpn (which is a product
of last PN received and replay protection and window size).

Signed-off-by: Michael Siedzik <msiedzik@extremenetworks.com>
2018-12-26 16:42:25 +02:00
michael-dev
b678ed1efc macsec: Make pre-shared CKN variable length
IEEE Std 802.1X-2010, 9.3.1 defines following restrictions for CKN:

"MKA places no restriction on the format of the CKN, save that it comprise
an integral number of octets, between 1 and 32 (inclusive), and that all
potential members of the CA use the same CKN. No further constraints are
placed on the CKNs used with PSKs, ..."

Hence do not require a 32 octet long CKN but instead allow a shorter CKN
to be configured.

This fixes interoperability with some Aruba switches, that do not accept
a 32 octet long CKN (only support shorter ones).

Signed-off-by: Michael Braun <michael-dev@fami-braun.de>
2018-12-25 17:29:15 +02:00
Jouni Malinen
93701b4afe tests: Allow TX/RX data test to use different frame length
This is needed for MACsec test cases with a bit shorter MTU.

Signed-off-by: Jouni Malinen <j@w1.fi>
2018-12-24 23:56:25 +02:00
Jouni Malinen
e422a819d0 Check snprintf result to avoid compiler warnings
These do not really get truncated in practice, but it looks like some
newer compilers warn about the prints, so silence those by checking the
result and do something a bit more useful if the output would actually
get truncated.

Signed-off-by: Jouni Malinen <j@w1.fi>
2018-12-24 11:09:22 +02:00
Damodaran, Rohit (Contractor)
ee98dd631a Readme for DPP
Addi a readme file for users for on-boarding devices with Device
Provisioning Protocol (DPP).

Signed-off-by: Rohit Damodaran <Rohit_Damodaran@comcast.com>
2018-12-23 17:25:11 +02:00
Andrej Shadura
c3f23ad6c7 dbus: Expose connected stations on D-Bus
Make it possible to list connected stations in AP mode over D-Bus, along
with some of their properties: rx/tx packets, bytes, capabilities, etc.

Signed-off-by: Mathieu Trudel-Lapierre <mathieu.trudel-lapierre@canonical.com>

Rebased by Julian Andres Klode <juliank@ubuntu.com> and updated to use
the new getter API.

Further modified by Andrej Shadura to not error out when not in AP mode
and to send separate StationAdded/StationRemoved signals instead of
changing signatures of existing StaAuthorized/StaDeauthorized signals.

Signed-off-by: Andrej Shadura <andrew.shadura@collabora.co.uk>
2018-12-23 17:25:11 +02:00
Andrej Shadura
f5f4c11aa1 dbus: Use dbus_bool_t, not int for boolean function arguments
Properties argument specifies whether to add object's properties
or not, hence it doesn't need to be int.

Signed-off-by: Andrej Shadura <andrew.shadura@collabora.co.uk>
2018-12-23 17:25:11 +02:00
Sergey Matyukevich
cdeea70f59 wpa_supplicant: Allow overriding HT STBC capabilities
Allow user to override STBC configuration for Rx and Tx spatial streams.
Add new configuration options to test for HT capability overrides.

Signed-off-by: Sergey Matyukevich <sergey.matyukevich.os@quantenna.com>
2018-12-23 17:25:11 +02:00
Jouni Malinen
0fb292c08e Add SAE to GET_CAPABILITY key_mgmt
Provide information about SAE AKM support in "GET_CAPABILITY key_mgmt"
for completeness. The "GET_CAPABILITY auth_alg" case is already
providing information about SAE support through user space SME.

Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
2018-12-21 21:49:02 +02:00
Prasad, Jagadeesh (Contractor)
d2b5138116 DPP: Add self configuration command in hostapd_cli and wpa_cli
The back-end support for DPP self configuration was already present in
hostapd and wpa_supplicant. However, the command to invoke DPP self
configuration was not available in hostapd_cli and wpa_cli. Add the
command "dpp_configurator_sign" in them.

Signed-off-by: Prasad, Jagadeesh <Jagadeesh_Prasad@comcast.com>
2018-12-21 12:02:57 +02:00
Jouni Malinen
53d5de6f1d DPP: Accept DPP_CONFIGURATION_SIGN without double space before parameters
Make this command more convenient to use by not requiring two space
characters between the command and the first parameter.

Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
2018-12-21 12:02:57 +02:00
Jouni Malinen
2a93ecc8ca Expose Multi-BSS STA capability through wpa_supplicant control interface
Indicate whether the driver advertises support for Multi-BSS STA
functionality with "GET_CAPABILITY multibss" (returns "MULTIBSS-STA" if
supported).

Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
2018-12-20 21:30:43 +02:00
Venkateswara Naralasetty
5abc7823bd wpa_supplicant: Add Multi-AP backhaul STA support
Advertise vendor specific Multi-AP IE in (Re)Association Request frames
and process Multi-AP IE from (Re)Association Response frames if the user
enables Multi-AP fuctionality. If the (Re)Association Response frame
does not contain the Multi-AP IE, disassociate.

This adds a new configuration parameter 'multi_ap_backhaul_sta' to
enable/disable Multi-AP functionality.

Enable 4-address mode after association (if the Association Response
frame contains the Multi-AP IE). Also enable the bridge in that case.
This is necessary because wpa_supplicant only enables the bridge in
wpa_drv_if_add(), which only gets called when an interface is added
through the control interface, not when it is configured from the
command line.

Signed-off-by: Venkateswara Naralasetty <vnaralas@codeaurora.org>
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Signed-off-by: Arnout Vandecappelle (Essensium/Mind) <arnout@mind.be>
2018-12-20 12:10:31 +02:00
Mathy Vanhoef
fa97981265 OCV: Include and verify OCI in WNM-Sleep Exit frames
Include and verify the OCI element in WNM-Sleep Exit Request and
Response frames. In case verification fails, the frame is silently
ignored.

Signed-off-by: Mathy Vanhoef <Mathy.Vanhoef@cs.kuleuven.be>
2018-12-17 15:50:12 +02:00
Mathy Vanhoef
034388ac9c OCV: Include and verify OCI in the AMPE handshake
Include and verify the OCI element in AMPE Open and Confirm frames. Note
that the OCI element is included even if the other STA didn't advertise
support of OCV. The OCI element is only required and verified if both
peers support OCV.

Signed-off-by: Mathy Vanhoef <Mathy.Vanhoef@cs.kuleuven.be>
2018-12-17 15:50:12 +02:00
Mathy Vanhoef
716ed96e8d OCV: Pass ocv parameter to mesh configuration
Signed-off-by: Mathy Vanhoef <Mathy.Vanhoef@cs.kuleuven.be>
2018-12-17 15:50:12 +02:00
Mathy Vanhoef
5c7d35ba07 Add UNPROT_DEAUTH command for testing OCV
This new wpa_supplicant control interface command can be used to
simplify testing SA Query with OCV.

Signed-off-by: Mathy Vanhoef <Mathy.Vanhoef@cs.kuleuven.be>
2018-12-17 15:50:12 +02:00
Mathy Vanhoef
f91e68e903 OCV: Perform an SA Query after a channel switch
After the network changed to a new channel, perform an SA Query with the
AP after a random delay if OCV was negotiated for the association. This
is used to confirm that we are still operating on the real operating
channel of the network. This commit is adding only the station side
functionality for this, i.e., the AP behavior is not changed to
disconnect stations with OCV that do not go through SA Query.

Signed-off-by: Mathy Vanhoef <Mathy.Vanhoef@cs.kuleuven.be>
2018-12-17 15:50:12 +02:00
Mathy Vanhoef
f9da7505bf OCV: Include and verify OCI in SA Query frames
Include an OCI element in SA Query Request and Response frames if OCV
has been negotiated.

On Linux, a kernel patch is needed to let clients correctly handle SA
Query Requests that contain an OCI element. Without this patch, the
kernel will reply to the SA Query Request itself, without verifying the
included OCI. Additionally, the SA Query Response sent by the kernel
will not include an OCI element. The correct operation of the AP does
not require a kernel patch.

Without the corresponding kernel patch, SA Query Requests sent by the
client are still valid, meaning they do include an OCI element.
Note that an AP does not require any kernel patches. In other words, SA
Query frames sent and received by the AP are properly handled, even
without a kernel patch.

As a result, the kernel patch is only required to make the client properly
process and respond to a SA Query Request from the AP. Without this
patch, the client will send a SA Query Response without an OCI element,
causing the AP to silently ignore the response and eventually disconnect
the client from the network if OCV has been negotiated to be used.

Signed-off-by: Mathy Vanhoef <Mathy.Vanhoef@cs.kuleuven.be>
2018-12-17 15:42:23 +02:00
Mathy Vanhoef
6ab73efa72 OCV: Add utility functions to insert OCI elements
This commit adds utility functions to insert various encoding of the OCI
element.

Signed-off-by: Mathy Vanhoef <Mathy.Vanhoef@cs.kuleuven.be>
2018-12-17 00:02:14 +02:00
Mathy Vanhoef
55c12f5d37 OCV: Advertise OCV capability in RSN capabilities (STA)
Set the OCV bit in RSN capabilities (RSNE) based on station mode
configuration.

Signed-off-by: Mathy Vanhoef <Mathy.Vanhoef@cs.kuleuven.be>
2018-12-16 20:49:27 +02:00
Mathy Vanhoef
875ab60d73 OCV: Advertise OCV capability in RSN capabilities (AP)
Set the OCV bit in RSN capabilities (RSNE) based on AP mode
configuration. Do the same for OSEN since it follows the RSNE field
definitions.

Signed-off-by: Mathy Vanhoef <Mathy.Vanhoef@cs.kuleuven.be>
2018-12-16 20:48:48 +02:00
Mathy Vanhoef
ce6829c284 OCV: Add wpa_supplicant config parameter
Add wpa_supplicant network profile parameter ocv to disable or enable
Operating Channel Verification (OCV) support.

Signed-off-by: Mathy Vanhoef <Mathy.Vanhoef@cs.kuleuven.be>
2018-12-16 20:31:21 +02:00
Mathy Vanhoef
138205d600 OCV: Add build configuration for channel validation support
Add compilation flags for Operating Channel Verification (OCV) support.

Signed-off-by: Mathy Vanhoef <Mathy.Vanhoef@cs.kuleuven.be>
2018-12-16 20:31:21 +02:00
Mathy Vanhoef
ad20a1367f Store the VHT Operation element of an associated STA
APs and mesh peers use the VHT Operation element to advertise certain
channel properties (e.g., the bandwidth of the channel). Save this
information element so we can later access this information.

Signed-off-by: Mathy Vanhoef <Mathy.Vanhoef@cs.kuleuven.be>
2018-12-16 18:35:30 +02:00
Mathy Vanhoef
4b62b52e5e Make channel_info available to the supplicant state machine
This adds the necessary functions and callbacks to make the channel_info
driver API available to the supplicant state machine that implements the
4-way and group key handshake. This is needed for OCV.

Signed-off-by: Mathy Vanhoef <Mathy.Vanhoef@cs.kuleuven.be>
2018-12-16 18:35:30 +02:00
Mathy Vanhoef
7f00dc6e15 Add driver API to get current channel parameters
This adds driver API functions to get the current operating channel
parameters. This encompasses the center frequency, channel bandwidth,
frequency segment 1 index (for 80+80 channels), and so on.

Signed-off-by: Mathy Vanhoef <Mathy.Vanhoef@cs.kuleuven.be>
2018-12-16 18:35:30 +02:00
Jouni Malinen
fb2dc898d6 WMM AC: Fix a typo in a comment
Signed-off-by: Jouni Malinen <j@w1.fi>
2018-12-08 16:50:42 +02:00
Jouni Malinen
22d8bb04d9 WMM AC: Do not write ERROR level log entries when WMM AC is not in use
These two wpa_printf() calls with MSG_ERROR level could be reached when
connecting without (Re)Association Response frame elements being
available. That would be the case for wired connections and IBSS. Those
cases are not supposed to use WMM AC in the first place, so do not
confuse logs with ERROR messages in them for normal conditions.

Signed-off-by: Jouni Malinen <j@w1.fi>
2018-12-08 16:48:33 +02:00
Jouni Malinen
06c00e6d93 OWE: Fix OWE network profile saving
key_mgmt=OWE did not have a config parameter writer and wpa_supplicant
was unable to save such a network profile correctly. Fix this by adding
the needed parameter writer.

Signed-off-by: Jouni Malinen <j@w1.fi>
2018-12-08 16:27:26 +02:00
Damodaran, Rohit (Contractor)
ad6a92472d DPP: Support DPP key_mgmt saving to wpa_supplicant configuration
In the existing code, there was no "DPP" string available to the DPP key
management type for configuration parser of wpa supplicant. When the
configuration is saved, the key management string was left out from the
config file. Fix this by adding support for writing key_mgmt=DPP option.

Signed-off-by: Rohit Damodaran <Rohit_Damodaran@comcast.com>
2018-12-08 16:17:48 +02:00
Jouni Malinen
3ce48c440e HS 2.0: Fix PMF-in-use check for ANQP Venue URL processing
The previous implementation did not check that we are associated with
the sender of the GAS response before checking for PMF status. This
could have accepted Venue URL when not in associated state. Fix this by
explicitly checking for association with the responder first.

This fixes an issue that was detected, e.g., with these hwsim test case
sequences:
gas_anqp_venue_url_pmf gas_anqp_venue_url
gas_prot_vs_not_prot gas_anqp_venue_url

Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
2018-12-08 14:06:58 +02:00
Jouni Malinen
f44d760cf0 HS 2.0: Enable PMF automatically for Hotspot 2.0 network profiles
Hotspot 2.0 Release 2 requires PMF to be negotiated, so enable this by
default in the network profiles created from cred blocks.

Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
2018-12-08 14:06:58 +02:00
Jouni Malinen
9ce2015a97 HS 2.0: Allocate enough buffer for HS 2.0 Indication element for scan
The HS 2.0 Indication element can be up to 9 octets in length, so add
two more octets to the minimum extra_ie buffer size for scanning.

Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
2018-12-08 14:06:58 +02:00
Jouni Malinen
ec2cf403b8 HS 2.0: As a STA, do not indicate release number greater than the AP
Hotspot 2.0 tech spec mandates mobile device to not indicate a release
number that is greater than the release number advertised by the AP. Add
this constraint to the HS 2.0 Indication element when adding this into
(Re)Association Request frame. The element in the Probe Request frame
continues to show the station's latest supported release number.

Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
2018-12-08 14:06:58 +02:00
Jouni Malinen
f2973fa39d FT: Fix CONFIG_IEEE80211X=y build without CONFIG_FILS=y
remove_ie() was defined within an ifdef CONFIG_FILS block while it is
now needed even without CONFIG_FILS=y. Remove the CONFIG_FILS condition
there.

Fixes 8c41734e5d ("FT: Fix Reassociation Request IEs during FT protocol")
Signed-off-by: Jouni Malinen <j@w1.fi>
2018-12-03 12:00:26 +02:00
Jouni Malinen
c2c6c01bb8 Update version to v2.7 and copyright years to include 2018
Also add the ChangeLog entries for both hostapd and wpa_supplicant to
describe main changes between v2.6 and v2.7.

Signed-off-by: Jouni Malinen <j@w1.fi>
2018-12-02 21:34:59 +02:00
Jouni Malinen
55570efe35 Uncomment CONFIG_LIBNL32=y in defconfig
libnl 3.2 release is much more likely to be used nowadays than the
versions using the older API, so uncomment this in wpa_supplicant and
hostapd defconfig.

Signed-off-by: Jouni Malinen <j@w1.fi>
2018-12-02 21:34:59 +02:00
Ashok Kumar
698c9e2021 OWE: Try another group only on association rejection with status 77
Do not change the OWE group if association is rejected for any other
reason than WLAN_STATUS_FINITE_CYCLIC_GROUP_NOT_SUPPORTED to avoid
unnecessary latency in cases where the APs reject association, e.g., for
load balancing reasons.

Signed-off-by: Ashok Kumar <aponnaia@codeaurora.org>
2018-12-02 20:42:09 +02:00
Jouni Malinen
117f586b05 DPP: Remove unused wpas_dpp_remain_on_channel_cb()
This function was apparently never used at all.

Signed-off-by: Jouni Malinen <j@w1.fi>
2018-12-02 18:40:06 +02:00
Jouni Malinen
e22c23382f DPP: Apply testing configuration option to signing of own config
Previous implementation had missed this case of setting configurator
parameters.

Signed-off-by: Jouni Malinen <j@w1.fi>
2018-12-02 00:26:21 +02:00
Jouni Malinen
8c41734e5d FT: Fix Reassociation Request IEs during FT protocol
The previous implementation ended up replacing all pending IEs prepared
for Association Request frame with the FT specific IEs (RSNE, MDE, FTE)
when going through FT protocol reassociation with the wpa_supplicant
SME. This resulted in dropping all other IEs that might have been
prepared for the association (e.g., Extended Capabilities, RM Enabled
Capabilities, Supported Operating Classes, vendor specific additions).

Fix this by replacing only the known FT specific IEs with the
appropriate values for FT protocol while maintaining other already
prepared elements.

Signed-off-by: Jouni Malinen <j@w1.fi>
2018-12-01 22:02:55 +02:00
Jouni Malinen
3d1d469195 Fix indentation level
This gets rid of smatch warnings about inconsistent indenting.

Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
2018-11-30 21:28:19 +02:00
Ashok Ponnaiah
fcb3f11e4d SAE: Fix external authentication on big endian platforms
Need to handle the little endian 16-bit fields properly when building
and parsing Authentication frames.

Fixes: 5ff39c1380 ("SAE: Support external authentication offload for driver-SME cases")
Signed-off-by: Ashok Ponnaiah <aponnaia@codeaurora.org>
2018-11-30 17:26:26 +02:00