It was possible for the error path to try to use P2P Group ID attribute
even if one was not included in the message. This could result in
dereferencing a NULL pointer, so re-check the pointer before copying the
data.
Signed-off-by: Jouni Malinen <j@w1.fi>
The special case of non-zero status code used in a GAS Comeback Response
frame to indicate that additional delay is needed before the response is
available was not working properly. This case needs to allow the status
code check to be bypassed for the comeback case prior to having received
any response data.
Signed-off-by: Jouni Malinen <j@w1.fi>
The simulated SIM/USIM case uses a separate milenage cred parameter, so
this cred password parameter was unused for this credential type.
Signed-off-by: Jouni Malinen <j@w1.fi>
It looks like leaving behind the freed pointed at the end of the array
could end up in a crash triggered by double free in some cases.
Signed-off-by: Jouni Malinen <j@w1.fi>
Commits 7ef6947993 and
533536d82a added this temporarily
disabling case, but those commits were merged in without having been
converted to the new os_reltime design used for ssid->disabled_until.
Consequently, they ended up disabling the network for 44 years or so too
long time (depending on what values the relative timestamp had
accummulated so far). Fix this by using relative timestamps
consistently.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Wait a bit between WPS_CONFIG command and the first scan. This can avoid
an extra five second wait due to having to scan again if the initial
scan operations happens to be quick enough to happen before the AP has
updated its configuration.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
PD Response is sent out using a 200 ms offchannel wait, but that wait
was not cancelled on TX status report. This could result in offchannel
operation being left waiting unnecessarily long. Fix this by making the
P2P_NO_PENDING_ACTION case in Action TX callback cancel the wait if a
pending wait is marked (and mark this for PD Response).
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
It looks like some deployed devices may send an invalid supported
operating class element (length = 0) in TDLS Setup messages. With
cfg80211, this results in the NL80211_CMD_SET_STATION command failing
due to an invalid argument (cfg80211 mandates supported operating
classes information to have a length of 2..253 octets).
Work around this interop issue by ignoring the Supported Operating Class
element if it has invalid length.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This verifies that 'INTERWORKING_SELECT auto' is able to pick the
correct network based on priority configuration when connected to a
lower priority network.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Commit d28f4e44f1 optimized Interworking
network selection in a case where the operation is run while already
connected to the selected network by skipping the reconnection. However,
this did not take into account that a higher priority network may have
shown up in the new scan results.
Fix this by checking whether network selection based on the latest scan
results (the ones from the interworking_select operation) would result
in a network with higher priority being selected. If so, skip the
optimization and force normal network connection (which will select this
newly found higher priority network). This fixes cases where a
non-Hotspot 2.0 network with higher priority (e.g., home network) shows
up while connected to a Hotspot 2.0 network with lower priority.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Commit 3d910ef497 tried to make
last-network selection behave more consistently with Interworking
network selection preferences. However, it did not take into account
that other network block may have higher priority. In such cases, the
last added network from Interworking network selection should actually
not be selected for the next connection. Fix this by limiting the
last-network preference to work only within a priority class.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
test_ap_hs20_multi_cred_sp_prio verifies that two credentials
provisioned by a single SP are selected properly based on sp_priority
when a single BSS matches both credentials.
test_ap_hs20_multi_cred_sp_prio2 does the same when there a separate BSS
for each credential.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
The new hostapd.conf parameter subscr_remediation_url can be used to
define the URL of the Subscription Remediation Server that will be added
in a WFA VSA to Access-Accept message if the SQLite user database
indicates that the user need subscription remediation.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
hostapd can now be configured to advertise OSU Providers with the
new osu_* confgiuration parameters.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
hostapd can now be configured to provide access for icon files
(hs20_icon config file parameter) for OSU. The hs20_icon data contains
additional meta data about the icon that is not yet used, but it will be
needed for the OSU Providers list ANQP element.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
If the authentication server includes the WFA HS 2.0 Session Info URL
AVP in Access-Accept, schedule ESS Disassociation Imminent frame to be
transmitted specified warning time prior to session timeout.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
If the RADIUS server includes deauthentication request in Access-Accept,
send a WNM-Notification frame to the station after 4-way handshake and
disconnect the station after configurable timeout.
A new control interface command, WNM_DEAUTH_REQ, is added for testing
purposes to allow the notification frame to sent based on local request.
This case does not disconnect the station automatically, i.e., a
separate control interface command would be needed for that.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
If the RADIUS server includes the WFA RADIUS VSA in Access-Accept to
indicate need for subscription remediation, copy the server URL from
the message and send it to the station after successfully completed
4-way handshake (i.e., after PTK is set to allow PMF to work) in a
WNM-Notification.
AP must not allow PMKSA caching to be used after subscription
remediation association, so do not add the PMKSA cache entry whenever
the authentication server is indicating need for subscription
remediation. This allows station reassociation to use EAP authentication
to move to non-remediation connection.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
If the station indicated support for Hotspot 2.0, send its release
number and PPS MO ID in Access-Request messages using the WFA RADIUS
VSA.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
The Access-Request frames are used to inform the RADIUS server about the
Hotspot 2.0 release number supported by the AP.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
