Add timeout to close incomplete DPP relay connections. This is needed to
avoid getting stuck with old entries that prevent new connections from
getting started.
Signed-off-by: Disha Das <dishad@codeaurora.org>
Simplify the implementation by using shared functions for parsing the
capabilities instead of using various similar but not exactly identical
checks throughout the implementation.
Signed-off-by: Jouni Malinen <j@w1.fi>
IEEE Std 802.11-2020 mandates H2E to be used whenever an SAE password
identifier is used. While this was already covered in the
implementation, the sae_prepare_commit() function still included an
argument for specifying the password identifier since that was used in
an old test vector. Now that that test vector has been updated, there is
no more need for this argument anymore. Simplify the older non-H2E case
to not pass through a pointer to the (not really used) password
identifier.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Define the new TWT attributes for configuring the broadcast TWT
parameters in enum qca_wlan_vendor_attr_twt_setup.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
The firmware rejects the TWT setup request when roaming and channel
switch is in progress. Extend enum qca_wlan_vendor_twt_status to
represent new reason codes for these cases.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
This changes the Send-Confirm value for the first SAE Confirm message to
be 1 instead of 0 for all cases to match the design shown in IEEE Std
802.11-2020, Figure 12-4 (SAE finite state machine).
Sc is defined to be "the number of SAE Confirm messages that have been
sent" which is a bit vague on whether the current frame is included in
the count or not. However, the state machine is showing inc(Sc)
operation in all cases before the "2" event to build the Confirm.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
The firmware sends new reason codes to indicate TWT teardown due to
single channel and multi channel concurrency. Update the enum
qca_wlan_vendor_twt_status to represent new reason code.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
When a public key is included in the PASN Parameters element, it should
be encoded using the RFC 5480 conventions, and thus the first octet of
the Ephemeral Public Key field should indicate whether the public key is
compressed and the actual key part starts from the second octet.
Fix the implementation to properly adhere to the convention
requirements for both wpa_supplicant and hostapd.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
The 6 GHz band operating class 136 is defined to use 20 MHz bandwidth.
Return the value accordingly from center_idx_to_bw_6ghz() to cover this
special case.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Define the following additional TWT attribute for
qca_wlan_vendor_attr_twt_setup:
QCA_WLAN_VENDOR_ATTR_TWT_SETUP_WAKE_INTVL2_MANTISSA to configure the
mantissa in microseconds.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
This adds new control interface commands TWT_SETUP and TWT_TEARDOWN. For
now, these are only for testing purposes to be able to trigger
transmission of the TWT Action frames without configuring any local
behavior for TWT in the driver.
Signed-off-by: Ben Greear <greearb@candelatech.com>
It is more convenient to see the exact error in the debug log instead of
getting noted that something was invalid.
Signed-off-by: Jouni Malinen <j@w1.fi>
Add a QCA vendor attribute to configure the driver to allow the 6 GHz
connection with all security types. This attribute is used for testing
purposes.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Add a QCA vendor attribute to ignore SAE H2E requirement mismatch for 6
GHz connection. This attribute is used for testing purposes.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
This is an attempt of making the code easier to understand for static
analyzers. The helper functions were already verifying that these IEs
are fully within the memory buffer, but that may not have been clear
enough for automated analysis.
Signed-off-by: Jouni Malinen <j@w1.fi>
BRCM vendor command used to trigger ACS scan. After ACS finished,
DHD driver will send results by event BRCM_VENDOR_EVENT_ACS.
Signed-off-by: Xinrui Sun <xinrui.sun@broadcom.com>
Determine if the TDLS peer is HE capable based on HE Capability element
received in the TDLS Setup Response frame. Indicate the peer's HE
capabilities to the driver through sta_add().
Signed-off-by: Sreeramya Soratkal <ssramya@codeaurora.org>
Add a QCA vendor attribute to enable/disable the Punctured Preamble Rx
support in HE PHY capabilities.
This attribute is used for testing purposes.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Add a QCA vendor attribute to configure the driver to disable data and
management response frame transmission to test the BSS max idle period
feature.
This attribute is used for testing purposes.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Add a QCA vendor attribute to configure the driver/firmware to use only
RU 242 tone for data frame transmission.
This attribute is used for testing purposes.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Add a QCA vendor attribute to configure the driver with a specific BSS
max idle period value to advertise in (Re)Association Request frames.
This attribute is used for testing purposes.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
The TX event for the next frame in the sequence might be received before
the TX status for the final GAS response frame is processed. This used
to result in the Config Result getting discarded and the negotiation not
completing successfully on the Configurator side.
Accept the Config Result message as an indication of the final GAS
response frame having went through fine even if the TX status has not
yet been processed to avoid this issue from a potential race condition
on kernel events.
Signed-off-by: Jouni Malinen <j@w1.fi>
Add additional attributes for the QCA vendor command
QCA_NL80211_VENDOR_SUBCMD_GET_STA_INFO to get finer details on roaming
behavior, TSF out of sync count, and the latest TX rate, Rate Index used
for the transmission.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Add definitions from IEEE Std 802.11ai-2016, 9.6.8.36 FILS discovery
frame format and extensions for the 6 GHz band from IEEE P802.11ax/D8.0.
Signed-off-by: Aloka Dixit <alokad@codeaurora.org>
According to latest IEEE 802.11 standard, Transmit Power Envelope
element is also relevant to IEEE 802.11ax and is no longer called VHT
Transmit Power Envelope. Remove the VHT naming from the element and move
hostapd_eid_txpower_envelope() from ieee802_11_vht.c to ieee802_11.c in
preparation of using it with HE.
Signed-off-by: Shay Bar <shay.bar@celeno.com>
There are 2 HW modes with IEEE80211_MODE_A: one for the 5 GHz channels
and one for 6 GHz channels. Since hw_get_chan() checks all the
compatible hw modes, eventually, an incorrect hw mode is selected.
To fix this, add a function that checks if a specific mode supports
the requested frequency and if so use it as the current mode.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
Allow HE MCS rate to be used for beacon transmission when the driver
advertises the support. The rate is specified with a new beacon_rate
option "he:<HE MCS>" in hostapd configuration.
Signed-off-by: Rajkumar Manoharan <rmanohar@codeaurora.org>
Use more accurate INTERWORKING_EXCLUDED for this. The actual event
prefix is not changed to remains compatible with external components
using this control interface event message.
Signed-off-by: Jouni Malinen <j@w1.fi>
In some contexts (e.g., Multi-AP) it can be useful to have access to
some of the management frames in upper layers (e.g., to be able to
process the content of association requests externally).
Add 'notify_mgmt_frames'. When enabled, it will notify the ctrl_iface
when a management frame arrives using the AP-MGMT-FRAME-RECEIVED event
message.
Note that to avoid completely flooding the ctrl_iface, not all
management frames are included (e.g., Beacon and Probe Request frames
are excluded).
Signed-off-by: Raphaël Mélotte <raphael.melotte@mind.be>
Old gcc versions complain about signed/unsigned comparison in
dpp_rx_gas_resp(). Hide it.
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
IEEE P802.11az/D2.6 added definitions to include RSNXE in the PASN
negotiation. Implement the new functionality in both wpa_supplicant and
hostapd.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
IEEE P802.11az/D2.6 defines the following additional capabilities to
RSNXE:
- Secure LTF support
- Secure RTT support
- Protection of range negotiation and measurement management frames.
Add support for advertising the new capabilities.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Add PASN implementation to wpa_supplicant
1. Add functions to initialize and clear PASN data.
2. Add functions to construct PASN Authentication frames.
3. Add function to process PASN Authentication frame.
4. Add function to handle PASN frame TX status.
5. Implement the station side flow processing for PASN.
The implementation is missing support for wrapped data and PMKSA
establishment for base AKMs, and only supports PASN authentication or
base AKM with PMKSA caching.
The missing parts will be added in later patches.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
In order to be able to perform secure LTF measurements, both the
initiator and the responder need to first derive TK and KDK and store
them, so they would later be available for the secure LTF negotiation.
Add a basic implementation of a PTKSA cache that stores derived TK/KDK
which can later be used for secure LTF negotiation, and add it to the
build configuration.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Add helper functions to construct a PASN Authentication frame and
validate its content, which are common to both wpa_supplicant and
hostapd.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
1. Add a function to derive the PTK from a PMK and additional data.
2. Add a function to calculate the MIC for a PASN frames.
3. Add a function to compute the hash of an authentication frame body.
The above are built only in case that CONFIG_PASN is enabled at build
time.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Extend the fils_pmk_to_ptk() to also derive Key Derivation
Key (KDK) which can later be used for secure LTF measurements.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Extend the wpa_pmk_r1_to_ptk() to also derive Key Derivation
Key (KDK), which can later be used for secure LTF measurements.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Extend the wpa_pmk_to_ptk() to also derive Key Derivation
Key (KDK), which can later be used for secure LTF measurements.
Update the wpa_supplicant and hostapd configuration and the
corresponding WPA and WPA Auth state machine, to allow enabling of KDK
derivation. For now, use a testing parameter to control whether KDK is
derived.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
PASN authentication requires that group management cipher suite
would be set to 00-0F-AC:7 in the RSNE, so consider it as a valid
group management cipher and adjust the code accordingly.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Add support for new channels 173 and 177 in the operating classes 125 to
130 as defined in draft IEEE P802.11ax/D8.0.
Signed-off-by: Sreeramya Soratkal <ssramya@codeaurora.org>
The operating class 129 includes channels with a maximum bandwidth of
160 MHz with center frequency index 50 and 114. The previous definition
of operating class 129 considered the center frequency index as actual
channels resulting in incorrect channel setup for the operating class.
Fix the definition of operating class 129 to consider channels with the
center frequency index of 50 and 114.
Also update the comment that describes the channel selection for
operating 128, 129, and 130 which mentions wpas_p2p_allow_channel()
verifies the channels while wpas_p2p_verify_channel() takes care of it.
Signed-off-by: Sreeramya Soratkal <ssramya@codeaurora.org>
After sending DPP Auth Response, the Responder might not receive the
Auth Confirm either due to the Initiator not sending it or the reception
of the frame failing for some reason (e.g., Responder having already
left the negotiation channel). If this happens, following initiation
attempts would fail since the consecutive Auth Request would get
discarded since the previous authentication is still in progress.
Terminate DPP authentication on Responder, if no Auth Confirm is
received within one second of successfully sending Auth Response. This
allows the Responder to accept start of a new exchange.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
The response for the respective TWT operations can either be synchronous
or asynchronous (wherever specified). If synchronous, the response to
this operation is obtained in the corresponding vendor command reply to
the user space. For asynchronous case, the response is obtained as an
event with the same operation type.
Drivers shall support either of these modes but not both simultaneously.
The support for asynchronous mode is advertised through the new flag
QCA_WLAN_VENDOR_FEATURE_TWT_ASYNC_SUPPORT. If the driver does not
include this flag, it shall support synchronous mode.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Define the following additional TWT operations:
QCA_WLAN_TWT_GET_STATS, QCA_WLAN_TWT_CLEAR_STATS,
QCA_WLAN_TWT_GET_CAPABILITIES, QCA_WLAN_TWT_SETUP_READY_NOTIFY.
Also define new attributes to qca_wlan_vendor_attr_twt_setup
and qca_wlan_vendor_attr_twt_nudge.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Replace the implicit boolean checks that used int variables with use of
a more explicit bool variable type.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Support possible band combinations of 2.4 GHz, 5 GHz, and 6 GHz with
QCA_WLAN_VENDOR_ATTR_SETBAND_MASK attribute. Ensure backwards
compatibility with old drivers that are using
QCA_WLAN_VENDOR_ATTR_SETBAND_VALUE attribute and supporting only 2.4 GHz
and 5 GHz bands.
Signed-off-by: Veerendranath Jakkam <vjakkam@codeaurora.org>
S1G beacons save a few bytes by not requiring the RSNE in beacon if RSN
BSS is configured. Handle this in wlantest by only clearing RSNE from
the BSS info if frame is a Probe Response frame.
Signed-off-by: Thomas Pedersen <thomas@adapt-ip.com>
Define QCA vendor attributes to dynamically configure TX NSS and RX NSS
to be used with QCA_NL80211_VENDOR_SUBCMD_SET_WIFI_CONFIGURATION and
QCA_NL80211_VENDOR_SUBCMD_GET_WIFI_CONFIGURATION commands.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
TWT nudge is a combination of suspend and resume in a single request.
Add TWT nudge operation and QCA vendor attributes to support
the TWT nudge request.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
P2P usage in the 6 GHz band is not standardized yet by WFA. Disable P2P
operations in the 6 GHz band to avoid potential interop issues with
existing P2P devices in production. P2P operations in the 6 GHz band can
be reenabled later after defining standard ways to address potential
interop issues with existing P2P devices.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Introduces a vendor specific feature capability
QCA_WLAN_VENDOR_FEATURE_CONCURRENT_BAND_SESSIONS to know if the device
supports concurrent network sessions on different Wi-Fi bands. This feature
capability is attributed to the hardware's capability to support the same
(e.g., DBS).
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Define a QCA vendor attribute
QCA_WLAN_VENDOR_ATTR_WIFI_TEST_CONFIG_FULL_BW_UL_MU_MIMO to
enable/disable full bandwidth UL MU-MIMO subfield in the HE PHY
capabilities information field for testing purposes.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
The allocated memory pointed by the pem pointer was freed on an error
path without clearing the pointer to NULL before returning it from the
function. This could have resulted in use of freed memory in an error
case. Fix this by clearing the pointer so that the function returns NULL
properly in the case of this error.
Fixes: ace3723d98 ("DPP2: Enterprise provisioning (Enrollee)")
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
DPP_CONFIGURATOR_ADD processing of the new ppkey parameter had a
copy-paste error in determining the correct length of this parameter.
Fix that by referencing the correct pointer.
Fixes: 9c1fbff074 ("DPP2: Generate a privacy protection key for Configurator")
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Add support for missing 6 GHz operating classes as defined in
IEEE P802.11ax/D7.0.
This is needed to avoid OCV failures on the 6 GHz band when the channel
width is larger than 20 MHz.
Signed-off-by: Veerendranath Jakkam <vjakkam@codeaurora.org>
Previously only primary channel number used to calculate 6GHz operating
class in ieee80211_freq_to_channel_ext() and it is always giving 131
operating class. Fix this by mapping operating class using chanwidth and
sec_channel also.
This is needed to avoid OCV failures on the 6 GHz band when the channel
width is larger than 20 MHz.
Signed-off-by: Veerendranath Jakkam <vjakkam@codeaurora.org>
In theory, the EVP_PKEY_get0_EC_KEY() could fail, so verify that it
succeeds before using the pointer to get the group.
Fixes: 65e94351dc ("DPP2: Reconfig Authentication Request processing and Response generation")
Signed-off-by: Disha Das <dishad@codeaurora.org>
IANA assigned the TCP port 8908 for DPP, so update the implementation to
match the formal assignment.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
If SAE_CONFIG_PK is not defined and sae->pk isn't zero (which is
possible as it is controlled by the commit message status code),
sae_derive_keys() may end up deriving PMK and KCK from an
uninitialized array. Fix that.
Fixes: 6b9e99e571 ("SAE-PK: Extend SAE functionality for AP validation")
Fixes: 20ccf97b3d ("SAE-PK: AP functionality")
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
The connection process fails for several reasons and the status codes
defined in IEEE Std 802.11 do not cover the locally generated reason
codes. Add an attribute to QCA_NL80211_VENDOR_SUBCMD_GET_STA_INFO vendor
sub command which can be used by the driver/firmware to report various
additional reason codes for connection failures.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
This allows the privacyProtectionKey to be transferred to a new
Configurator similarly to the way c-sign-key is transferred.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Use ppKey instead of C-sign-key to encrypted E-id to E'-id into Reconfig
Announcement frame on the Enrollee side.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Store the received privacy protection key from Connector into
wpa_supplicant network profile and indicate it through the control
interface similarly to C-sign-key.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
This provides the new privacy protection key to the Enrollee so that
this can be used to protect E-id in Reconfig Announcement frames.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Generate a new key for Configurator. This is either generated
automatically for the specified curve or provided from external source
with the new ppkey=<val> argument similarly to the way c-sign-key was
previously generated.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
We don't really need to duplicate more of this, so just
move the lib.rules include to the end and do more of the
stuff that's common anyway there.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Derive the library name from the directory name, and let each
library Makefile only declare the objects that are needed.
This reduces duplicate code for the ar call. While at it, also
pretty-print that call.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This is something I hadn't previously done, but there are
cases where it's needed, e.g., building 'wlantest' and then
one of the tests/fuzzing/*/ projects, they use a different
configuration (fuzzing vs. not fuzzing).
Perhaps more importantly, this gets rid of the last thing
that was dumped into the source directories, apart from
the binaries themselves.
Note that due to the use of thin archives, this required
building with absolute paths.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Instead of building in the source tree, put most object
files into the build/ folder at the root, and put each
thing that's being built into a separate folder.
This then allows us to build hostapd and wpa_supplicant
(or other combinations) without "make clean" inbetween.
For the tests keep the objects in place for now (and to
do that, add the build rule) so that we don't have to
rewrite all of that with $(call BUILDOBJS,...) which is
just noise there.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Define a control event with bootstrap id, frame source, frequency, and
chirp hash for receipt of Presence Announcement (chirp) frames.
Signed-off-by: Andrew Beltrano <anbeltra@microsoft.com>
DPP tech spec was modified to use v1(0) instead of v2(1) for the
OneAsymmetricKey in the Configurator backup structure to match the
description in RFC 5958 Section 2 which indicates v2 to be used when any
items tagged as version 2 are included. No such items are actually
included in this case, so v1 should be used instead.
Change OneAsymmetricKey generation to use v1(0) instead of v2(1) and
parsing to accept either version to be used. This is not backwards
compatible with the earlier implementation which requires v2(1) when
parsing the received value.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
crypto_bignum_init_set() might fail in case of memory allocation
failures. These two cases within sswu() did not handle that properly,
i.e., a memory allocation failure could have resulted in dereferencing a
NULL pointer. Check the return value before proceeding to fix this.
Fixes: aeb022f8e5 ("SAE: Implement hash-to-element PT/PWE crypto routines")
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Introduce QCA_ATTR_ROAM_CONTROL_SCAN_SCHEME_TRIGGERS that represents the
triggers for which the scan scheme from enum qca_roam_scan_scheme has to
be applied.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
The firmware sends a new status code to indicate an already suspended
TWT session. Update the status code enum to represent this state.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
IEEE Std 802.11 specifies that the Operating Classes field terminates
immediately before the OneHundredAndThirty Delimiter (i.e., an octet
with value 130). Move the operating class value 130 last in the global
op_class array so that it gets added as the last entry into the
Supported Operating Clases element and the 6 GHz operating class is
parsed in that element by implementation that stop at the assumed
OneHundredAndThirty Delimiter.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Add additional attributes to enum qca_vendor_attr_roam_control to
control the roam behavior through QCA_NL80211_VENDOR_SUBCMD_ROAM and
QCA_WLAN_VENDOR_ATTR_ROAMING_PARAM_CONTROL.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Add new QCA vendor attributes to get thermal level from the driver. The
driver may return thermal level when userpace requests, or send a
thermal event when thermal level changes.
Signed-off-by: Hu Wang <huw@codeaurora.org>
Enhance the return values of ocv_verify_tx_params with enum to indicate
different OCI verification failures to caller.
Signed-off-by: Veerendranath Jakkam <vjakkam@codeaurora.org>
This was changed in the protocol design to include nonce from both
devices, so update implementation to match.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
