Commit graph

326 commits

Author SHA1 Message Date
Kanchanapally, Vidyullatha
e903d32d41 Parallelize distinct radio work operations
This commit contains the necessary changes to parallelize
distinct radio work operations which are different in type and
the band used, only when the underlying driver is capable of
supporting such simultaneous offchannel operations.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2015-10-01 01:41:46 +03:00
Jouni Malinen
dfaf11d648 P2P: Require fresh scan results for persistent group re-invocation
The P2P group is not yet operating when going through invitation
exchange for re-invocation. Previously, an old cached scan result could
be used to skip the scan immediately after the invitation exchange.
While this may result in the fastest possible connection, it does have
some issues with cases where the GO takes some time to start up. It
would also be at least theoretically possible for some of the BSS
parameters to be different, so having a fresh scan result from the new
GO instance may be desired in any case.

Add a mechanism to skip scan results that have been last updated before
a specific point in time and as the first user for this mechanism,
require chan results to be more recent than the invitation message
exchange for the P2P Client role in persistent group re-invocation case.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2015-08-22 00:22:12 +03:00
Andrei Otcheretianski
b9da88d6c1 P2PS: Authorize any peer for P2PS method if interface address not known
When P2PS PD with default P2PS method is done, the peer that becomes GO
should authorize the client. However, P2PS specification doesn't require
the client to include its intended interface address in PD
Request/Response. As a result, the P2P Client's interface address may not
be known and any address may need to be authorized.

Previously, client's P2P Device Address was used for authorization,
which is not correct when a dedicated interface is used for P2P Client.
This is not resulting in a connection failure, however it causes a
significant delay (until WPS_PIN_TIME_IGNORE_SEL_REG elapses). Fix this
by authorizing the intended interface address, if known; or any address,
if not known.

Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
2015-08-06 20:45:15 +03:00
Jouni Malinen
84bcb4e7a9 FST: Mark fst_ies buffer const
This buffer is owned by the FST module, so mark it const in the
set_ies() callback to make it clearer which component is responsible for
modifying and freeing this.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2015-08-03 17:40:30 +03:00
Gautam
d4e597959c P2P: Fix P2P configuration file name
The P2P configuration file is wrongly set as STA configuration file,
even though a separate configuration file is mentioned with '-m' option.
Add initialization and deallocation of global.params->conf_p2p_dev to
fix this.

Signed-off-by: Gautam <gautams@broadcom.com>
2015-08-02 21:37:09 +03:00
Srinivas Dasari
844dfeb804 QCA vendor command support to set band to driver
Add vendor command to pass SET setband command to the driver and read
the updated channel list from driver when this notification succeeds.
This allows the driver to update its internal channel lists based on
setband configuration.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2015-07-28 21:00:18 +03:00
Anton Nayshtut
b36a3a65aa FST: Integration into wpa_supplicant
This commit integrates the FST into the wpa_supplicant.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2015-07-16 18:26:15 +03:00
Ilan Peer
f43c1ae798 P2P: Handle P2P Device dedicated interface parent removal
In case of a network interface removal, check if the interface
was also the parent interface of the P2P Device dedicated interface.
If this is the case, then stop the P2P Device functionality, and
remove the P2P Device dedicated interface.

In case that the interface is added again and P2P Device
functionality can be enabled again, add a new P2P Device dedicated
interface and allow further P2P Device functionality.

In case that the P2P Device dedicated interface is re-created, the
original P2P Device configuration file is needed, so store it in
the global params (instead in the wpa_interface configuration).

Signed-off-by: Ilan Peer <ilan.peer@intel.com>
2015-06-19 16:22:26 +03:00
Avraham Stern
e1dffa3b2c P2P: Fix PBC overlap detection
PBC overlap detection searches for another BSS with active PBC in the
BSS table. However, when a separate P2P interface is used, scan results
without P2P IE are not saved in the BSS table, so non-P2P BSS's with
active PBC will not be detected.

Fix this by iterating only the WPS AP array instead of the BSS table.
This is also more efficient since only WPS APs may have active PBC. This
also fixes hwsim test "grpform_pbc_overlap" when a dedicated P2P Device
is used.

Signed-off-by: Avraham Stern <avraham.stern@intel.com>
2015-06-19 11:25:21 +03:00
Max Stepanov
07c1e987d5 P2PS: Enable Probe Request frame processing by P2P Client
1. Add global p2p_cli_probe property to enable/disable Probe Request
frame RX reporting for connected P2P Clients. The property can be set to
0 - disable or 1 - enable. The default value is 0.

2. Enable Probe Request frame RX reporting for P2P Client on
WPA_COMPLETED state if p2p_cli_probe property is set to 1. Disable it
when an interface state is changing to any other state.

3. Don't cancel Probe Request frame RX reporting on wpa_stop_listen for
a connected P2P Client handling Probe Request frames.

Signed-off-by: Max Stepanov <Max.Stepanov@intel.com>
Reviewed-by: Ilan Peer <ilan.peer@intel.com>
2015-06-14 23:16:55 +03:00
Krishna Vamsi
a80651d067 Add support to request a scan with specific SSIDs
Support a request to scan specific SSIDs given by user with the SCAN
command. The SSID list can be suffixed to the scan command as follows.
For example, if SSIDs "ABC" and "abc123" need to be specifically
scanned, the command should be "SCAN ssid 414243 ssid 616263313233". The
value of the SSID is passed in hexadecimal representation.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2015-06-05 15:55:26 +03:00
Ilan Peer
b4342ca4d8 P2P: Use p2p_init_wpa_s for P2P command redirection over D-Bus
D-Bus used the p2p_dev member in struct wpa_supplicant to track the
interface used for P2P Device operations. However, this is not needed as
the interface used for P2P Device operations is stored in struct
wpa_global->p2p_init_wpa_s.

Replace all the redirections to wpa_s->p2p_dev with redirections to
wpa_s->global->p2p_init_wpa_s and removed this member as it is no
longer needed.

Signed-off-by: Ilan Peer <ilan.peer@intel.com>
2015-05-25 18:31:09 +03:00
Jouni Malinen
5aeebc48e8 D-Bus Fix network_is_persistent_group() for P2P operations
Commit c2762e410f ('P2P: Update D-Bus
network object semantics during group formation') added this helper
function to determine whether a network block is used for storing a
persistent group information. However, it implemented this in a way that
matches both persistent group storage and an operating persist group
instance. This does not seem to match the expected behavior for the
D-Bus objects, so fix this to match only the persistent group storage
case to avoid registering/unregistered incorrect D-Bus objects for
groups.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2015-04-29 20:52:22 +03:00
Mikael Kanstrup
8b423edbd3 Declare all read only data structures as const
By analysing objdump output some read only structures were found in
.data section. To help compiler further optimize code declare these
as const.

Signed-off-by: Mikael Kanstrup <mikael.kanstrup@sonymobile.com>
2015-04-25 17:33:06 +03:00
Hu Wang
e7d20342b5 WPS: Enforce five second minimum time before AP iteration
Previously, wpa_supplicant was using number of scan iterations
(WPS_PIN_SCAN_IGNORE_SEL_REG = 3) to give some time for finding a WPS AP
with Selected Registrar TRUE before starting to iterate through all WPS
APs. While this works fine in most cases, some drivers may return the
initial three scan results so quickly that the total amount of time is
only couple of seconds in case none of the APs are initially advertising
Selected Registrar TRUE. To give some more time for APs (WPS Registrars)
to become ready, add an additional constraint on the iteration based on
time (WPS_PIN_TIME_IGNORE_SEL_REG = 5 seconds).

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2015-04-24 17:55:32 +03:00
Jouni Malinen
d9d1b9527a Use SSID_MAX_LEN define instead of value 32 when comparing SSID length
This makes the implementation easier to understand.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2015-04-22 11:44:18 +03:00
Jithu Jance
efa232f915 Add support for virtual interface creation/deletion
Extend interface_add and interface_remove commands via an optional
argument to allow wpa_supplicant to create/delete a new virtual
interface.

Signed-off-by: Jithu Jance <jithu@broadcom.com>
2015-03-26 22:20:35 +02:00
Avraham Stern
9bd566a33a Delay AP selection if all networks are temporarily disabled
If all networks are temporarily disabled, delay AP selection until at
least one network is enabled. Running AP selection when all networks are
disabled is useless as wpa_supplicant will not try to connect. In
addition, it will result in needless scan iterations that may delay the
connection when it is needed.

Signed-off-by: Avraham Stern <avraham.stern@intel.com>
2015-03-22 20:53:58 +02:00
Jouni Malinen
1772d348ea P2P: Fix interface deinit for failed group interface initialization
wpa_supplicant_deinit_iface() ends up removing all P2P groups if the
removed interface is the parent interface. This is correct behavior in
general, but this resulted in issues in the new group interface
initialization error path since wpa_s->parent was not assigned before
hitting this check. Fix this by assigning wpa_s->parent as part of
wpa_supplicant_add_iface().

Signed-off-by: Jouni Malinen <j@w1.fi>
2015-03-01 22:36:53 +02:00
Jouni Malinen
c28059091a Do not add blacklist entries based on normal disconnect request cases
There are number of cases where wpa_supplicant requests the current
connection to be disconnected before starting a new operation. Such
cases do not really indicate that there was an error in connecting or a
disconnection initiated by the AP, so do not add a temporary blacklist
entry in such sequences.

Signed-off-by: Jouni Malinen <j@w1.fi>
2015-03-01 15:54:24 +02:00
Jouni Malinen
a1b790eb9d Select AP based on estimated maximum throughput
This modifies the BSS selection routines to calculate SNR and estimated
throughput for each scan result and then use the estimated throughput as
a criteria for sorting the results. This extends the earlier design by
taking into account higher throughput rates if both the AP and local
device supports HT20, HT40, or VHT80. In addition, the maximum rate is
restricted based on SNR.

In practice, this gives significantly higher probability of selecting
HT/VHT APs when there are multiple BSSes in the same ESS and SNR is not
low enough to prevent higher MCS use.

Signed-off-by: Jouni Malinen <j@w1.fi>
2015-02-22 11:09:54 +02:00
Masashi Honma
bf51f4f82b mesh: Fix remaining BLOCKED state after SAE auth failure
When SAE authentication fails, wpa_supplicant retries four times. If all
the retries result in failure, SAE state machine enters BLOCKED state.
Once it enters this state, wpa_supplicant doesn't retry connection. This
commit allow connection retries even if the state machine entered
BLOCKED state.

There could be an opinion "Is this patch needed? User could know the SAE
state machine is in the BLOCKED mode by MESH-SAE-AUTH-BLOCKED event.
Then user can retry connection. By user action, SAE state machine can
change the state from BLOCKED to another.". Yes, this is a true at the
joining mesh STA. However, a STA that is already a member of existing
mesh BSS should not retry connection because if the joining mesh STA
used wrong password, all the existing STA should do something from UI to
retry connection.

Signed-off-by: Masashi Honma <masashi.honma@gmail.com>
2015-02-08 12:43:24 +02:00
Krishna Vamsi
93eca6155b P2PS: Do not remove pending interface on p2p_stop_find
The pending interface created during provision discovery should
not be removed on stopping p2p_find. This pending interface has
to be used after completing GO negotiation. Earlier the pending
interface is created just before GO negotiation so there was no
problem.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2015-02-03 01:35:07 +02:00
Krishna Vamsi
306aaf49f8 P2PS: Start WPS registrar upon GO formation
If P2PS config method is used for provisioning, upon forming a new GO,
start WPS registrar for the provisioned peer automatically.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2015-02-03 01:35:07 +02:00
Krishna Vamsi
9a58e521ac P2PS: Callback to create pending group after sending PD Response
This introduces a P2P module callback function that will be used to
create the pending P2PS group after sending PD Response and receiving
ACK status for it.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2015-02-03 01:35:07 +02:00
Krishna Vamsi
6d9085145c P2PS: Process P2PS provisioning commands
This extends wpas_p2p_prov_disc() implementation to accept P2PS
parameters. None of the callers are yet using this functionality; the
following commit introduces a user.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2015-02-03 01:35:07 +02:00
Jouni Malinen
3f56a2b746 Ignore pmf=1 default if driver does not support PMF
Connection with a PMF enabled AP will fail if we try to negotiate PMF
while the local driver does not support this. Since pmf=1 does not
require PMF for a successful connection, it can be ignored in such a
case to avoid connectivity issues with invalid configuration. This makes
it somewhat easier to allow upper layer programs to use pmf=1 default
regardless of driver capabilities.

Signed-off-by: Jouni Malinen <j@w1.fi>
2015-01-27 12:38:52 +02:00
Ben Rosenfeld
d90bfa97f4 Move external_scan_running to wpa_radio
external_scan_running should be common to all interfaces that share a
radio. This fixes a case where external_scan_running was set on a single
interface, but did not block scan on other interfaces.

Signed-off-by: Ben Rosenfeld <ben.rosenfeld@intel.com>
2015-01-20 01:57:59 +02:00
Jouni Malinen
2d9c99e37b Retry scan-for-connect if driver trigger fails
This restores some of the pre-radio work behavior for scanning by
retrying scan trigger if the driver rejects it (most likely returning
EBUSY in case of nl80211-drivers). Retry is indicated in the
CTRL-EVENT-SCAN-FAILED event with "retry=1".

For manual scans (e.g., triggered through "SCAN" control interface
command), no additional retries are performed. In other words, if upper
layers want to retry, they can do so based on the CTRL-EVENT-SCAN-FAILED
event.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2015-01-19 20:25:20 +02:00
Jouni Malinen
911942ee64 Add a test framework for various wpa_supplicant failure cases
For CONFIG_TESTING_OPTIONS=y builds, add a new test parameter than can
be used to trigger various error cases within wpa_supplicant operations
to make it easier to test error path processing. "SET test_failure
<val>" is used to set which operation fails. For now, 0 = no failures
and 1 = scan trigger fails with EBUSY. More operations can be added in
the future to extend coverage.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2015-01-19 19:34:00 +02:00
Jouni Malinen
a8826b1848 Interworking: Avoid busy loop in scan result mismatch corner cases
It was possible for interworking_find_network_match() to find a possible
BSS match in a case where more thorough checks in
wpa_supplicant_select_bss() reject network. This itself is fine, in
general, but when combined with wpa_supplicant_fast_associate()
optimization and auto_interworking=1, this resulted in a busy loop of up
to five seconds and a possible stack overflow due to recursion in that
loop.

Fix this by limiting the Interworking wpa_supplicant_fast_associate()
call to be used only once per scan iteration, so that new scan
operations can be completed before going through the scan results again.

Signed-off-by: Jouni Malinen <j@w1.fi>
2015-01-17 01:52:07 +02:00
Jouni Malinen
54fe48b9dc mesh: Use the shared function with IBSS to determine channel parameters
Automatically enable HT20, HT40+, HT40-, or VHT, based on driver
capabilities. This obsoletes the mesh_ht_mode network block parameter
that was previously used to configure HT parameters.

Signed-off-by: Jouni Malinen <j@w1.fi>
2015-01-10 17:35:53 +02:00
Jouni Malinen
6334330ed6 mesh: Use a separate variable to track whether HT is enabled
A network profile parameter should not be used to check whether the
currently operating mesh has HT enabled.

Signed-off-by: Jouni Malinen <j@w1.fi>
2015-01-10 17:35:53 +02:00
Ilan Peer
56c76fa592 scan: Add MAC address randomization in scan handling
1. Supported MAC address randomization for scan.
2. Supported MAC address randomization for scheduled scan.
2. Supported MAC address randomization for pno.
4. Add functions to set and clear the MAC address randomization
   state variables.

Signed-off-by: Ilan Peer <ilan.peer@intel.com>
2015-01-04 23:06:31 +02:00
Eliad Peller
8c42b36902 WMM AC: Reconfigure tspecs on reassociation to the same BSS
The specification requires the tspecs to be kept upon reassociation to
the same BSS. Save the last tspecs before such reassociation, and
reconfigure on the association notification.

Note that the current flow is not transparent to the user
(it is notified about deauth/reassoc and tspec removal/addition).

Signed-off-by: Eliad Peller <eliadx.peller@intel.com>
2015-01-04 18:41:00 +02:00
Jouni Malinen
d97a3c4885 SME: Optimize OBSS scanning
Include only the potentially affected channel range in OBSS scans to
reduce the amount of offchannel time needed for scanning when requested
by the AP.

Signed-off-by: Jouni Malinen <j@w1.fi>
2014-12-22 22:07:03 +02:00
Masashi Honma
5b78493f3b mesh: Add mesh interface creation command for mesh gate
The mesh gate is used to bridge (or route) between mesh network and
another network. For example, mesh gate acts as router between mesh
network and IEEE 802.11 BSS network.

This command makes a virtual mesh interface to be used for mesh gate.

This command expects to be used like this.

wpa_cli -i wlan0 MESH_INTERFACE_ADD ifname=mesh0
wpa_cli -i mesh0 add_network
wpa_cli -i mesh0 set_network 0 ssid '"commell_2X_mmm"'
wpa_cli -i mesh0 set_network 0 mode 5
wpa_cli -i mesh0 set_network 0 frequency 2412
wpa_cli -i mesh0 set_network 0 key_mgmt SAE
wpa_cli -i mesh0 set_network 0 psk '"01234567"'
wpa_cli -i mesh0 mesh_group_add 0
wpa_cli -i wlan0 mesh_group_remove mesh0

Signed-off-by: Masashi Honma <masashi.honma@gmail.com>
2014-12-14 23:27:43 +02:00
Jouni Malinen
568475b70b HS 2.0: Allow CANCEL_FETCH_OSU to stop at scan completion
There is no need to start the GAS/ANQP fetch if the FETCH_OSU operation
has already been canceled.

Signed-off-by: Jouni Malinen <j@w1.fi>
2014-12-14 02:28:03 +02:00
Jouni Malinen
e374522827 Do not start new radio work on scan completion during ext work
Externally triggered scan could result in a new radio work item getting
started even when external radio work was in progress. Delay such start
until the external work is completed.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2014-12-01 20:17:08 +02:00
Andrei Otcheretianski
70d1e72849 wpa_supplicant: Handle link measurement requests
Send link measurement response when a request is received. Advertise
only RCPI, computing it from the RSSI of the request. The TX power field
is left to be filled by the driver. All other fields are not published.

Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
2014-11-22 21:45:07 +02:00
Assaf Krauss
4c4b230527 wpa_supplicant: Add an option to specify SSID in neighbor report requests
Allow supplying an SSID for the SSID IE. If not supplied, no SSID IE is
sent, and the request implies the current SSID.

Signed-off-by: Assaf Krauss <assaf.krauss@intel.com>
2014-11-22 21:36:42 +02:00
Assaf Krauss
d89c0701db wpa_supplicant: Add support for Neighbor Report
Add the ability to send a Neighbor Report Request (part of
RRM). Requester is then notified once the report arrives.

Signed-off-by: Assaf Krauss <assaf.krauss@intel.com>
2014-11-22 21:23:14 +02:00
Assaf Krauss
b361d580ec SME: Add RRM support to association request
In case the AP we are associating with advertises support for RRM,
advertise our own RRM support in the (Re)Association Request frame. This
is done by adding an RRM Capabilities IE. The underlying driver is
expected to further add a Power Capabilities IE to the request, and set
the Radio Measurement flag in the Capability Info field. At this point
the RRM Capabilities IE advertises no measurement support.

Signed-off-by: Assaf Krauss <assaf.krauss@intel.com>
2014-11-22 21:13:45 +02:00
Assaf Krauss
f936b73c4f wpa_supplicant: Store driver's RRM capabilities
Store the RRM capability flags reported by the underlying driver.

Signed-off-by: Assaf Krauss <assaf.krauss@intel.com>
2014-11-22 21:07:56 +02:00
Jouni Malinen
e1117c1c01 WNM: Optimize BSS transition management scans
When the list of preferred transition candidates is received, use the
identified channels to optimize the following scan so that no time is
wasted on other channels.

Signed-off-by: Jouni Malinen <j@w1.fi>
2014-11-22 20:17:47 +02:00
Jouni Malinen
d0b9ab69f6 WNM: Move transition candidate list processing to normal scan
This makes it easier to optimize transition request processing.

Signed-off-by: Jouni Malinen <j@w1.fi>
2014-11-22 18:40:03 +02:00
Jouni Malinen
8c9af762f3 WNM: Calculate valid-until time for transition candidate list
This is of more use than the raw validity interval (number of beacon
intervals) that was recorded previously.

Signed-off-by: Jouni Malinen <j@w1.fi>
2014-11-22 18:06:27 +02:00
Moshe Benji
d1f880013a WMM AC: Handle TSPEC action frames
Add the TSPEC to the driver on successful TSPEC ADDTS response. Delete
the TSPEC when receiving DELTS action.

Signed-off-by: Moshe Benji <moshe.benji@intel.com>
Signed-off-by: Eliad Peller <eliad@wizery.com>
2014-11-16 21:07:08 +02:00
Eliad Peller
674f6c073f WMM AC: Add basic ADDTS/DELTS sending functions
Add basic implementation for ADDTS and DELTS sending
functions.

wpas_wmm_ac_addts() will send ADDTS request public action,
containing TSPEC (traffic stream specification) with
the given params.

wpas_wmm_ac_delts() will look for the saved tspec with
the given tid, and send DELTS public action for it.

(Handling of ADDTS response and actually configuring the admission
control params will be added in following patches.)

Signed-off-by: Moshe Benji <moshe.benji@intel.com>
Signed-off-by: Eliad Peller <eliad@wizery.com>
2014-11-16 21:03:56 +02:00
Moshe Benji
471cd6e10c WMM AC: Add add_tx_ts and del_tx_ts driver ops
Add add_tx_ts() and del_tx_ts() ops to notify the driver about
TSPEC add / delete.

Additionally, add wmm_ac_supported flag to indicate
whether the driver supports WMM AC.

Signed-off-by: Moshe Benji <moshe.benji@intel.com>
Signed-off-by: Eliad Peller <eliad@wizery.com>
2014-11-16 20:47:36 +02:00