The multi-SSID design that used a single beaconing BSSID with multiple
SSIDs was never completed in this repository, so there is no need to
maintain the per-STA ssid/ssid_probe pointers that could only point to
&hapd->conf->ssid. Save some memory and reduce code complexity by
removing this unused partial capability.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This makes it easier to interpret debug logs for cases where hostapd
control multiple interfaces.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This makes it easier to interpret debug logs in case hostapd controls
multiple interfaces and a STA roams between them.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Currently, vlan_remove_dynamic() is only called when the station VLAN ID
is changed (ap_sta_bind_vlan), but not when the station is freed. So
dynamic VLAN interfaces are not removed actually except within 1x
reauthentification VLAN ID change, although most of the code is already
there.
This patch fixes this by calling vlan_remove_dynamic() in ap_free_sta().
It cannot just use sta->vlan_id for this, as this might have been
changed without calling ap_sta_bind_vlan() (ap/ieee802_11.c:handle_auth
fetches from RADIUS cache for WPA-PSK), thus reference counting might
not have been updated. Additionally, reference counting might get wrong
due to old_vlanid = 0 being passed unconditionally, thus increasing the
reference counter multiple times.
So tracking the currently assigned (i.e., dynamic_vlan counter
increased) VLAN is done in a new variable sta->vlan_id_bound. Therefore,
the old_vlan_id argument of ap_sta_bind_vlan() is no longer needed and
setting the VLAN for the sta in driver happens unconditionally.
Additionally, vlan->dynamic_vlan is only incremented when it actually
is a dynamic VLAN.
Signed-off-by: Michael Braun <michael-dev@fami-braun.de>
hostapd receives NEWLINK messages multiple times and thus does
configuration of the the vlan interface multiple times.
This is not required and leads to the following during cleanup in
test pmksa_cache_preauth_vlan_used:
1. run-test.py does: brctl delif brvlan1 wlan3.1
2. hostapd processes NEWLINK and does: brctl addif brvlan1 wlan3.1
3. run-test.py does: brctl delbr brvlan1
-> fails as wlan3.1 is still in the bridge
This patch fixes this by ignoring repeated NEWLINK messages.
Signed-off-by: Michael Braun <michael-dev@fami-braun.de>
When hitting
> Failed to create interface wlan3.1: -23 (Too many open files in system)
> Try to remove and re-create wlan3.1
hostapd deletes the AP_VLAN interface and then recreates it. Thus the
kernel assigns the same ifidx to the new interfaces and sends DELLINK
and NEWLINK mesages.
As the DELLINK messages are processed after the struct hostapd_vlan is
added, hostapd deletes the struct hostapd_vlan entry, deconfigures the
AP_VLAN interface and leaves vlan_newlink nothing to find afterwards.
So this patch makes DELLINK messages to be ignored when the interface
exists.
Signed-off-by: Michael Braun <michael-dev@fami-braun.de>
Previously, during RSN preauthentication, ap_sta_bind_vlan() was called,
which fails for non-zero sta->vlan_id as the station is not known to the
kernel driver.
Fix this by binding the station only if it is associated. If it is not
associated, ap_sta_bind_vlan() will be done later during association.
In addition, reject Access-Accept if the returned VLAN ID is not valid
in the current hostapd configuration.
Signed-off-by: Michael Braun <michael-dev@fami-braun.de>
is_ht_allowed is a confusing name since this variable is used to track
whether 40 MHz channel bandwidth is allowed instead of whether HT is
allowed in general.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
If NEED_AP_MLME=y is not defined, compilation might
fail under some configurations:
src/ap/drv_callbacks.c:594:2: warning: implicit declaration of
function ‘hostapd_acs_completed’ [-Wimplicit-function-declaration]
src/ap/sta_info.c:253: undefined reference to `sae_clear_retransmit_timer'
Fix these errors by adding the missing hostapd_acs_completed() stub,
and defining NEED_AP_MLME in case of CONFIG_SAE.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Add SQLite error message and DB name to the DB related errors. Add
enough tracing so that users can know exactly where users are failing to
be found.
Signed-off-by: Ben Greear <greearb@candelatech.com>
HT requires QoS/WMM, so unset HT capabilities for a station
whose association request does not include a valid WMM IE.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Update ACS driver offload feature for VHT configuration. In addition,
this allows the chanlist parameter to be used to specify which channels
are included as options for the offloaded ACS case.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
There's off-by-one in the range availability check - the case of
first_chan_idx + num_chans == num_channels should be allowed (e.g., 0 +
1 == 1, for the case of a single 20 MHz channel).
Signed-off-by: Maital Hahn <maitalm@ti.com>
Signed-off-by: Eliad Peller <eliad@wizery.com>
When looking for a new operating channel, consider the case of
non-contiguous channels when checking all the needed channels (e.g., the
driver might support channels 36, 38, 40, so look for channels 36+40
explicitly, instead of failing when encountering channel 38).
Signed-off-by: Eliad Peller <eliad@wizery.com>
If the AP/Authenticator receives an EAPOL-Key msg 2/4 for an association
that negotiated use of PSK and the EAPOL-Key MIC does not match, it is
likely that the station is trying to use incorrect PSK/passphrase.
Report this with "AP-STA-POSSIBLE-PSK-MISMATCH <STA addr>" control
interface event.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This event was previously used only when disabling AP mode operation
through hostapd control interface. Make this more consistent by
providing same indication when disabling hostapd interface through the
interface deinit path. This adds the event to the case where a full
hostapd radio instance is removed which also applies for the
wpa_supplicant AP mode operations.
Signed-off-by: Jouni Malinen <j@w1.fi>
Modify the string for AP-CSA-FINISHED event indication to include a flag
which tells the framework whether the new channel is a DFS channel.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Add handling logic for DFS offloaded case, and add a helper function
that takes the frequency (MHz) as a param and returns 1 if given channel
requires DFS, or 0 otherwise.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
If DFS is offloaded to the driver, hostapd should not be performing
these operations. Send the relevant control interface events to provide
information to upper layer software that may use such events to track
DFS/CAC state. This makes the offloaded DFS implementation more
consistent with the DFS-in-hostapd behavior.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Disable VHT caps for STAs for which there is not even a single
allowed MCS in any supported number of streams. i.e STA is
advertising 3 (not supported) as VHT MCS rates for all supported
streams.
Signed-off-by: Rajkumar Manoharan <rmanohar@qti.qualcomm.com>
This change adds the function hostapd_config_clear_wpa_psk() that
deletes an entire wpa_psk structure, making sure to follow the linked
list and to free the allocated memory of each PSK node. This helps to
prevent memory leaks when using PSKs from multiple sources and
reconfiguring the AP during runtime.
Signed-off-by: Stefan Tomanek <stefan.tomanek@wertarbyte.de>
Read p2p_go_ctwindow (0-127 TUs) from the config file, and pass it to
the driver on GO start.
Use p2p_go_ctwindow=0 (no CTWindow) by default.
Signed-off-by: Eliad Peller <eliadx.peller@intel.com>
If the driver indicates that the interface has been disabled, assume
that all associations have been lost and remove the hostapd STA entries.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This uses couple of additional helper macros and prints more debug
information to make the VLAN events easier to analyze.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Sending client probe on already removed client from kernel driver does
not have any benefit and may lead unintended behavior among variable
drivers (mac80211 has a WARN_ON() that could have been triggered after
ifconfig down+up earlier when hostapd did not re-enable beaconing on
ifup). Skip this step in discussion when the kernel driver reports that
client entry is removed.
Signed-off-by: Peter Oh <poh@qca.qualcomm.com>
This allows WPA2 mode AP to be re-enabled automatically after external
ifconfig down + up on a netdev used by hostapd.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This is a step towards enabling hostapd to restart AP mode functionality
if the interface is disabled and re-enabled, e.g., with ifconfig down
and up. This commit takes care of beaconining only which may be
sufficient for open mode connection, but not for WPA2 cases.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Do not reply to a Probe Request frame with a DSSS Parameter Set element
in which the channel is different than the operating channel of the AP,
as the sending station is not found on the AP's operating channel.
IEEE Std 802.11-2012 describes this as a requirement for an AP with
dot11RadioMeasurementActivated set to true, but strictly speaking does
not allow such ignoring of Probe Request frames if
dot11RadioMeasurementActivated is false. Anyway, this can help reduce
number of unnecessary Probe Response frames for cases where the STA is
less likely to see them (Probe Request frame sent on a neighboring, but
partially overlapping, channel).
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
If HT40 co-ex scan fails due to the driver rejecting scan triggers
multiple times, it was possible for the ap_ht40_scan_retry() timeout
being left behind and it getting run after hapd->drv_priv has been
cleared. This would result in NULL pointer dereference in
driver_nl80211_scan.c. Fix this by canceling the timeout when disabling
the interface.
Signed-off-by: Jouni Malinen <j@w1.fi>
Previously, a channel with even a single scan/survey result missing
information was skipped in ACS. This may not be desirable in cases when
multiple scan iterations are used (which is the case by default in
hostapd). Instead, use all channels that provided at least one complete
set of results. Calculate the average interference factor as an average
of the iterations that did provide complete values.
This seems to help with some cases, e.g., when ath9k may not be able to
report the noise floor for all channels from the first scan iteration
immediately after the driver has been loaded, but then returns it for
all other scan iterations.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
The new acs_chan_bias configuration parameter is a space-separated list
of <channel>:<bias> pairs. It can be used to increase (or decrease) the
likelihood of a specific channel to be selected by the ACS algorithm.
The total interference factor for each channel gets multiplied by the
specified bias value before finding the channel with the lowest value.
In other words, values between 0.0 and 1.0 can be used to make a channel
more likely to be picked while values larger than 1.0 make the specified
channel less likely to be picked. This can be used, e.g., to prefer the
commonly used 2.4 GHz band channels 1, 6, and 11 (which is the default
behavior on 2.4 GHz band if no acs_chan_bias parameter is specified).
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
The interference factors for adjacent 2.4 GHz channels were summed
together without doing any kind of weighted average on them. This
resulted in the channels at the band edges getting undue preference due
to only including interference factors from three channels vs. five for
the channels in the middle of the band.
While it is somewhat unclear whether the design here was supposed to
count overlapping channels together in this way or whether that is
already covered in channel survey results, it is clear that this summing
of three to five values together and then comparing the sum rather than
average of some kind gives too much preference to the channels at the
edges of the band by assuming that there is no interference whatsoever
outside the band.
Use weighted average of the interference factors rather than a sum from
different number of values. For now, the adjacent 2.4 GHz channels get
weight of 0.85 (1.0 for the main channel itself) and the neighboring
channels to those adjacent ones get 0.55 weight. Band-edge channels are
handled in a way that takes average over the channels that were actually
considered instead of assuming zero interference from neighboring bands.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
If OBSS scan interval is not set, the AP must not schedule a timeout to
restore 40 MHz operation immediately after having moved to a 20 MHz
channel based on an unsolicited co-ex report. Fix this by scheduling the
timeout only if obss_interval is non-zero.
Since we do not currently support AP doing OBSS scans after the initial
BSS setup, this means practically that 40-to-20 MHz transition is
allowed, but 20-to-40 MHz is not with obss_interval=0. The latter gets
enabled if obss_interval is set to a non-zero value so that associated
STAs can take care of OBSS scanning.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Use standard numbers-and-dots format for IPv4 in debug logs instead
of hexdump in two different byte orders.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Previously, the old VLAN ID could have been deleted before the STA was
bound to the new VLAN in case the RADIUS server changed the VLAN ID
during an association. This did not exactly work well with mac80211, so
reorder the operations in a way that first binds the STA to the new VLAN
ID and only after that, removes the old VLAN interface if no STAs remain
in it.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Previously, it was possible for some corner cases to leave the WPA
authenticator state machine running if PMK could not be derived. Change
this to forcefully disconnect the STA to get more consistent behavior
and faster notification of the error.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This type of error reporting cases should use wpa_printf() to get
consistent debug logging behavior.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This modifies struct wpa_ptk to allow the length of KCK and KEK to be
stored. This is needed to allow longer keys to be used, e.g., with
Suite B 192-bit level.
Signed-off-by: Jouni Malinen <j@w1.fi>
