The credential MAC address is not necessarily that of the AP, i.e., it
is more likely to be that of the Enrollee. Check the scan results
against the current BSSID as well if match is not found otherwise when
going through the mixed mode workaround.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
The previously used 10 second timer did not really make much sense since
the Initiator is not going to be waiting for the response that long.
Change this to 1 second based on the DPP tech spec change.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This makes the full DPP deinit operation more consistent with stopping
of a single operation. In practice, this adds the new GAS client
stopping functionality.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Previously this stopped only the DPP Authentication instance, but it is
better to clear both PKEX and Authentication.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
An additional TX status callback could result in processing the DPP
authentication completion another time at least with hostapd. Fix this
by clearing the dpp_auth_ok_on_ack when processing it.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Add CONFIG_TESTING_OPTIONS ifdef protection to couple of forgotten DPP
test parameters in wpa_supplicant ctrl_iface.
Signed-off-by: Ashok Ponnaiah <aponnaia@qti.qualcomm.com>
It was possible for a timeout from an old GAS server operation to
trigger DPP configuration failure during the subsequent DPP operation.
Fix this by verifying that the status callback is for the response
generated during the same DPP Authentication/Configuration exchange.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Configurator signing its own Connector was previously supported only in
wpa_supplicant. This commit extends that to hostapd to allow an AP
acting as a Configurator to self-configure itself.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This allows external applications to get event indication for Probe
Request frames. Extend ctrl iface cmd "ATTACH" to enable this event on
per-request basis. For example, user has to send ctrl iface cmd "ATTACH
probe_rx_events=1" to enable the Probe Request frame events.
Signed-off-by: bhagavathi perumal s <bperumal@qti.qualcomm.com>
Previous implementation did not handle number of sequences correctly.
Make sure the iteration continues in both unicast and broadcast cases
until the five attempts have been made. In addition, improve timing by
checking 10 second time from the beginning of each iteration round and
not the last channel on which the Auth Req frame has been transmitted.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Previously, the Authentication Request frame was retried after 2+10 = 12
seconds since the wait for the response was not accounted for. Substract
that wait from the 10 second wait time to start the retries more quickly
based on the 10 second timer described in the tech spec.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
If unicast Authentication Request frame is used and the peer ACKs such a
frame, but does not reply within the two second limit, there is no need
to continue trying to retransmit the request frames since the peer was
found, but not responsive.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
The new conf={sta,ap}-{sae,psk-sae} parameter values can now be used to
specify that the legacy configuration object is for SAE.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This allows DPP to be used for enrolling credentials for SAE networks in
addition to the legacy PSK (WPA-PSK) case. In addition, enable FT-PSK
and FT-SAE cases automatically.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Retransmit the PKEX Exchange Request frame if no response from a peer is
received. This makes the exchange more robust since this frame is sent
to a broadcast address and has no link layer retries.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Extend dpp_test to allow more invalid attribute values to be written
into Peer Discovery Request/Response frames.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Extend dpp_test to cover a case where Config Attrib Object value is
invalid in Configuration Request frame.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This extends wpa_supplicant DPP implementation to retransmit DPP
Authentication Response frame every 10 seconds up to 5 times if the peer
does not reply with DPP Authentication Confirm frame.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Previously, this command stopped listen operation immediately, but if
there was an ongoing authentication exchange, a new listen operation was
started. This is not really expected behavior, so stop the
authentication exchange first with this command to avoid restarting
listen operation.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
The new role=either parameter can now be used with DPP_AUTH_INIT to
indicate that the initiator can take either the Configurator or Enrollee
role.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This extends wpa_supplicant to iterate over all available channels from
the intersection of what the peer indicates and the local device
supports when initiating DPP Authentication. In addition, retry DPP
Authentication Request frame up to five times if no response is
received.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Generate the PKEX bootstrapping information and release the PKEX session
in a helper function that both the initiator and responder can use
instead of maintaining this functionality separately in two places.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This commit introduces the ACS functionality for the autonomous GO. The
optional parameter <freq> in p2p_group_add is enhanced to carry a value
"acs" with the intention to select the channels among any supported
band. freq = 2 / 5 carry the need to select the channels only in the
respective bands 2.4 / 5 GHz. This functionality is on top of the host
driver's capability to offload ACS, which is advertized through
WPA_DRIVER_FLAGS_ACS_OFFLOAD.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Add limit on number of failed attempts that could have used PKEX code.
If the limit (5) is reached, drop the PKEX state (including the code)
and report this on the control interface to indicate that a new code
needs to be entered due to possible attack.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Clean up the pending PKEX exchange if Commit-Reveal Request processing
indicates a mismatch in the PKEX code. Previously, the this case was
silently ignored and the session was left in pending state that
prevented new PKEX exchanges from getting initated. Now, a new attempt
is allowed to be initiated.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Report mismatching finite cyclic group with PKEX Exchange Response using
STATUS_BAD_GROUP and provide more detailed error report over the control
interface on the peer device when this happens.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Indicate to upper layers if PKEX Commit-Reveal Request frame AES-SIV
decryption fails. That is a likely sign of the PKEX code mismatch
between the devices.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
DPP AKM should really require PMF to be used, but since that is not yet
explicitly required in the specification, make PMF enabled for now. For
legacy PSK cases, configure PMF to be enabled as well to support both
APs in no-PMF, optional-PMF, and required-PMF configuration.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Allow the Initiator to request a different channel to be used for DPP
Authentication and DPP Configuration exchanges. This commit adds support
for this in wpa_supplicant with the optional neg_freq=<freq in MHz>
parameter in DPP_AUTH_INIT.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This allows wpa_supplicant dpp_config_obj_override,
dpp_discovery_override, and dpp_groups_override parameters to be cleared
by setting them to a zero-length value.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This is useful for protocol testing purposes and UI needs to display
more detailed information about DPP exchanges.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This is helpful for testing purposes and also for upper layer components
that may want to show more detailed progress through a DPP exchange.
Both the DPP-TX and DPP-TX-STATUS events are provided.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This is helpful for testing purposes and also for upper layer components
that may want to show more detailed progress through a DPP exchange.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Now that dpp_check_attrs() takes care of verifying that no attributes
are after the Wrapped Data attribute, the duplicated checks in hostapd
and wpa_supplicant side of the implementation can be removed.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Add a generic mechanism for configuring the DPP implementation to behave
in particular different (mostly incorrect) ways for protocol testing
purposes. The new dpp_test parameter can be set to a non-zero integer to
indicate a specific behavior. This is only available in
CONFIG_TESTING_OPTIONS=y builds.
This commit include cases for an extra attribute being added after the
Wrapped Data attribute and Initiator/Responder capabilities having an
unexpected zero capability.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Seems like some test cases, e.g., ap_wpa2_psk_ext_retry_msg_3c, require
larger buffer than 256 bytes.
In other case I fail such test cases when run on real HW and using:
CONFIG_CTRL_IFACE=udp-remote
Increase the RX buffer from 256 to 4096 bytes to match the other control
interface cases.
Signed-off-by: Janusz Dziedzic <janusz.dziedzic@gmail.com>
After an initial connection wpa_supplicant derives ERP information which
can be used in doing eventual authentications in the same realm. This
information can be used by drivers with offloaded FILS support to do
driver/firmware initiated roamings. Add support to send this updated
information to such drivers.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This is needed to be able to use the same implementation for updating
the connection parameters in the driver during an association.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Update the replay counter after a roam for all cases. This restores the
design back to what it was before commit
01ef320f19 ('FILS: Update ERP next
sequence number with driver offload').
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
The new wpa_supplicant RESEND_ASSOC command can be used to request the
last (Re)Association Request frame to be sent to the AP to test FT
protocol behavior.
This functionality is for testing purposes and included only in builds
with CONFIG_TESTING_OPTIONS=y.
Signed-off-by: Jouni Malinen <j@w1.fi>
The new wpa_supplicant "KEY_REQUEST <error=0/1> <pairwise=0/1>" command
can be used to request an EAPOL-Key Request frame to be sent to the AP.
This functionality is for testing purposes and included only in builds
with CONFIG_TESTING_OPTIONS=y.
Signed-off-by: Jouni Malinen <j@w1.fi>
This can be used to test replay protection. The "RESET_PN" command in
wpa_supplicant and "RESET_PN <addr>" command in hostapd resets the local
counters to zero for the last configured key. For hostapd, the address
parameter specifies which STA this operation is for or selects GTK
("ff:ff:ff:ff:ff:ff") or IGTK ("ff:ff:ff:ff:ff:ff IGTK").
This functionality is for testing purposes and included only in builds
with CONFIG_TESTING_OPTIONS=y.
Signed-off-by: Jouni Malinen <j@w1.fi>
This was originally added to allow the IEEE 802.11 protocol to be
tested, but there are no known fully functional implementations based on
this nor any known deployments of PeerKey functionality. Furthermore,
PeerKey design in the IEEE Std 802.11-2016 standard has already been
marked as obsolete for DLS and it is being considered for complete
removal in REVmd.
This implementation did not really work, so it could not have been used
in practice. For example, key configuration was using incorrect
algorithm values (WPA_CIPHER_* instead of WPA_ALG_*) which resulted in
mapping to an invalid WPA_ALG_* value for the actual driver operation.
As such, the derived key could not have been successfully set for the
link.
Since there are bugs in this implementation and there does not seem to
be any future for the PeerKey design with DLS (TDLS being the future for
DLS), the best approach is to simply delete all this code to simplify
the EAPOL-Key handling design and to get rid of any potential issues if
these code paths were accidentially reachable.
Signed-off-by: Jouni Malinen <j@w1.fi>
Commit 03ed0a5239 ('WNM: Ignore WNM-Sleep
Mode Response if WNM-Sleep Mode has not been used') started ignoring the
response when no WNM-Sleep Mode Request had been used during the
association. This can be made tighter by clearing the used flag when
successfully processing a response. This adds an additional layer of
protection against unexpected retransmissions of the response frame.
Signed-off-by: Jouni Malinen <j@w1.fi>
The new sae_password network profile parameter can now be used to set
the SAE password instead of the previously used psk parameter. This
allows shorter than 8 characters and longer than 63 characters long
passwords to be used.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
While considering the movement of P2P GO from its current operating
channel, do not mark a DFS channel as invalid if DFS is offloaded
to the driver.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Previously, wpas_p2p_select_go_freq_no_pref() ended up selecting a 2.4
GHz band channel first before even considering 5 or 60 GHz channels.
This was likely done more or less by accident rather than by design when
the 5 GHz and 60 GHz band extensions were added. It seems reasonable to
enhance this by reordering the code to start with 5 and 60 GHz operating
classes and move to 2.4 GHz band only if no channel was available in 5
or 60 GHz bands for P2P GO use.
This does have some potential interop issues with 2.4 GHz only peer
devices when starting up an autonomous GO (i.e., without there being
prior knowledge of channels that the peers support). Upper layers are
expected to enforce 2.4 GHz selection if that is needed for some use
cases.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This allows CONFIG_TESTING_OPTIONS=y builds of wpa_supplicant to
override the OWE DH Parameters element in (Re)Association Request frames
with arbitrary data specified with the "VENDOR_ELEM_ADD 13 <IE>"
command. This is only for testing purposes.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This additional field was added to DPP Public Action frames in DPP tech
spec v0.2.3 to support cryptographic agility in the future.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Previously, only the SME-in-wpa_supplicant case was supported. This
extends that to cover the drivers that implement SME internally (e.g.,
through the cfg80211 Connect command).
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This extends OWE support in wpa_supplicant to allow DH groups 20 and 21
to be used in addition to the mandatory group 19 (NIST P-256). The group
is configured using the new network profile parameter owe_group.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This extends OWE support in hostapd to allow DH groups 20 and 21 to be
used in addition to the mandatory group 19 (NIST P-256).
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Add support for using the OWE Transition Mode element to determine the
hidden SSID for an OWE BSS that is used in transition mode.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
sm->pmk_len was not set when deriving the PMK as part of OWE key
generation. This depending on wpa_sm_set_pmk_from_pmksa() call resetting
the value to the default. While this worked for many cases, this is not
correct and can have issues with network profile selection based on
association information. For example, the OWE transition mode cases
would hit an issue here.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This adds new wpa_supplicant configuration parameters (go_interworking,
go_access_network_type, go_internet, go_venue_group, go_venue_type) to
add a possibility of configuring the P2P GO to advertise Interworking
element.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Update the default scan IEs when OCE is enabled/disabled to the
driver/firmware, so that the correct IEs will be sent out by the
driver/firmware in Probe Request frames.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
The new wpa_supplicant network parameter group_mgmt can be used to
specify which group management ciphers (AES-128-CMAC, BIP-GMAC-128,
BIP-GMAC-256, BIP-CMAC-256) are allowed for the network. If not
specified, the current behavior is maintained (i.e., follow what the AP
advertises). The parameter can list multiple space separate ciphers.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This adds phase1 parameter tls_suiteb=1 into wpa_supplicant
configuration to allow TLS library (only OpenSSL supported for now) to
use Suite B 192-bit level rules with RSA when using >= 3k (3072) keys.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
The new psk=<hexdump> can be used as an alternative to pass=<passphrase>
when configuring the DPP Configurator with a legacy network parameters.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Previously, wowlan_triggers were updated in kernel only during startup.
Also update it whenever it is set from the control interface.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Previously, the code that writes mesh_rssi_threshold to a network block
always executes, but the code that reads it from network block and the
code that initializes it to a default value in a new network block are
inside #ifdef CONFIG_MESH. As a result when writing a config file it
will write mesh_rssi_threshold (since it has a non-default value) and
later fail to read the network block.
Fix this by moving the write code under #ifdef CONFIG_MESH as well.
Note, network blocks which already have mesh_rssi_threshold because of
the bug will still fail to read after the fix.
Signed-off-by: Lior David <qca_liord@qca.qualcomm.com>
The introduction of radio works and a delayed callback to complete
association/connection requests ended up breaking RSN pre-authentication
candidate list generation for the case of pre-connection scan results.
Previously, wpa_supplicant_associate() set the RSN state machine
configuration before returning and the calls to
wpa_supplicant_rsn_preauth_scan_results() immediately after this
function call were working fine. However, with the radio work callback,
the RSN state machine configuration started to happen only in that
callback which would be called soon after this code path has completed.
This resulted in the RSN state machine not knowing the selected SSID and
as such, rejecting all pre-authentication candidates.
Fix this by setting the RSN state machine configuration from
wpa_supplicant_associate() so that the existing callers of
wpa_supplicant_rsn_preauth_scan_results() can be used as-is to add
candidates for pre-authentication.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
secy_init_macsec() can fail (if ->macsec_init fails), and
ieee802_1x_kay_init() should handle this and not let MKA run any
further, because nothing is going to work anyway.
On failure, ieee802_1x_kay_init() must deinit its kay, which will free
kay->ctx, so ieee802_1x_kay_init callers (only ieee802_1x_alloc_kay_sm)
must not do it. Before this patch there is a double-free of the ctx
argument when ieee802_1x_kay_deinit() was called.
Signed-off-by: Sabrina Dubroca <sd@queasysnail.net>
When building wpa_ie in wpas_start_assoc_cb() with ext_capab,
make sure that assignment does not exceed max_wpa_ie_len.
Signed-off-by: Adiel Aloni <adiel.aloni@intel.com>
This introduces a new interface for mesh and adds a signal that
is similar to the control interface event MESH-GROUP-STARTED.
Signed-off-by: Saurav Babu <saurav.babu@samsung.com>
The new "SET sae_commit_override <hexdump>" control interface command
can be used to force wpa_supplicant to override SAE commit message
fields for testing purposes. This is included only in
CONFIG_TESTING_OPTIONS=y builds.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
DPP tech spec changed the contents of these frames by replacing the
public key hash attributes with a Transaction ID attribute that gets
copied from the request to the response to identify the transaction in a
simpler manner.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Previously, CONFIG_WNM enabled build that supports WNM for both
station mode and AP mode. However, in most wpa_supplicant cases only
station mode WNM is required and there is no need for AP mode WNM.
Add support to differentiate between station mode WNM and AP mode
WNM in wpa_supplicant builds by adding CONFIG_WNM_AP that should be
used when AP mode WNM support is required in addition to station mode
WNM. This allows binary size to be reduced for builds that require
only the station side WNM functionality.
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
When setting the frequencies for beacon report request scan, it is
possible that a frequency is added twice (e.g., when the same channel
appears both in the channel field and in the AP channel report
subelement). This may cause the scan request to fail.
Make sure the frequencies array contains no duplications before
requesting the scan.
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
Send Radio Measurement response with measurement mode set to reject
in the following cases:
1. Reporting conditions is not supported.
2. No valid channels found for the measurement
Sending a response with an incapable indication will stop the AP from
sending other measurement requests of the same type as specified
in IEEE Std 802.11-2016, 11.11.6.
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
When failing to trigger scan for beacon report (e.g., when the
requested duration is not supported by the driver), send a
Radio Measurement response with the mode set to refused and don't
retry the scan.
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
IEEE Std 802.11-2016, 11.11.6 specifies that a station that is unable to
make a requested measurement or refuses to make a measurement shall
respond only if the measurement request was received within an
individually addressed radio measurement request frame, but shall not
respond if such a request was received in a group addressed frame.
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
Add a build option to select different default ciphers for OpenSSL
instead of the hardcoded default "DEFAULT:!EXP:!LOW".
This new option is useful on distributions where the security level
should be consistent for all applications, as in Fedora [1]. In such
cases the new configuration option would be set to "" or
"PROFILE=SYSTEM" to select the global crypto policy by default.
[1] https://fedoraproject.org/wiki/Changes/CryptoPolicy
Signed-off-by: Beniamino Galvani <bgalvani@redhat.com>
If an AP is not FILS capable and wpa_supplicant has a saved network
block for the network with FILS key management and a saved erp info,
wpa_supplicant might end up issuing a FILS connection to a non-FILS AP.
Fix this by looking for the presence of FILS AKMs in wpa_s->key_mgmt,
i.e., after deciding on the AKM suites to use for the current
connection.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
In case that an mbo object is allocated, but there is a failure
to resize the wpabuf, need to free the mbo object.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Scan results with parent TSF older than the scan start TSF are not added
to the beacon report since they are considered as scan results from
previous scans. However, for drivers that report the scan start TSF but
not the parent TSF of each scan result, the parent TSF will be zero so
valid scan results will be dropped.
Fix this by filtering scan results by the parent TSF only if the
driver supports reporting the parent TSF for each scan result.
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
Clear the get_pref_freq_list_override in p2p_ctrl_flush(). This fixes
the case when a dedicated P2P device interface is used.
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
dpp.h file requires openssl in order to compile, which breaks
compilation on systems without it.
Move DPP_OUI_TYPE to ieee802_11_defs.h and don't include dpp.h when
not really needed.
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
If a DFS forced frequency is provided in 'p2p_group_add' and the driver
supports DFS offload, the frequency was rejected in
wpas_p2p_init_go_params(). However, it was accepted in
wpas_p2p_select_go_freq() and wpas_p2p_group_add(). To make the behavior
consistent, the DFS frequency is now accepted in
wpas_p2p_init_go_params() similar to the way done in
wpas_p2p_select_go_freq().
Redundant check in wpas_p2p_group_add() for DFS forced frequency is
removed.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Add changes to control interface command get_capability to advertize
FILS capability, FILS AKMs suites, and FILS Authentication algorithms
based on the driver capabilities.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Add support to scan for a specific BSSID through the wpa_supplicant
control interface.
Usage: wpa_cli scan bssid=ab:bc:cd🇩🇪ef:12
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
The DPP Configurator can use this new command to generate its own signed
connector for the network that it manages.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
All the arguments to this command are optional, so do not mandate at
least one to be included in wpa_cli.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This allows wpa_supplicant to be configured to act as the configurator
in the case where a peer device initiates DPP Authentication.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This implements genric PKEX functionality in src/common/dpp.c and glue
code to use this in wpa_supplicant (i.e, hostapd DPP implementation does
not yet support PKEX).
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Set temporary disallowed BSSID list to the driver so that the driver
doesn't try to connect to any of the blacklisted BSSIDs during
driver-based roaming operation. This commit includes support only for
the nl80211 driver interface using a QCA vendor command for this.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
The new pass=<hexdump> parameter to DPP_AUTH_INIT can now be used to
specify the passphrase to use in config object.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
The new ssid=<hexdump> parameter to DPP_AUTH_INIT can now be used to
specify the SSID to use in config object.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This script can be used to process Android logcat information for
scanned QR Codes (e.g., from Barcode Scanner app) and also to display QR
Codes for locally generated bootstrap keys.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
wpa_supplicant can now be configured to generate a network profile
automatically based on DPP configuration. The following
dpp_config_processing values can be used to specify the behavior:
0 = report received configuration to an external program for
processing; do not generate any network profile internally (default)
1 = report received configuration to an external program and generate
a network profile internally, but do not automatically connect
to the created (disabled) profile; the network profile id is
reported to external programs
2 = report received configuration to an external program, generate
a network profile internally, try to connect to the created
profile automatically
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Commit 5538fc9309 ('FILS: Track completion
with FILS shared key authentication offload') added an additional case
for calling wpa_supplicant_event_assoc_auth() from EVENT_ASSOC handling
in case of FILS-completion with driver-based-SME. However, that checked
what placed outside the data != NULL case while data != NULL needs to
apply for this case as well due to wpa_supplicant_event_assoc_auth()
behavior. Move the data != NULL check to apply to both cases to avoid
potentially issues if a driver interface were to return EVENT_ASSOC
without the associate data. (CID 164708)
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
While encoded == NULL could happen in the case of an empty blob, that
will result in encoded_len == 0 and base64_decode() not derefencing the
src argument. That seems to be too difficult for some static analyzers,
so to avoid false warnings, explicitly reject the encoded == NULL case
without even trying to base64 decode it. (CID 164709)
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This new AKM is used with DPP when using the signed Connector to derive
a PMK. Since the KCK, KEK, and MIC lengths are variable within a single
AKM, this needs number of additional changes to get the PMK length
delivered to places that need to figure out the lengths of the PTK
components.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This adds DPP bootstrapping, authentication, and configuration into
hostapd similarly to how the design was integrated in wpa_supplicant.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This adds support for DPP Configuration Protocol using GAS. Full
generation and processing of the configuration object is not included in
this commit.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Add wpa_supplicant control interface commands for parsing the bootstrap
info URI from a QR Code (get peer public key) and to generate a new
bootstrap info with private key for local use. The optional
key=<hexdump> argument to the DPP_BOOTSTRAP_GEN command can be used to
specify the bootstrapping private key in OpenSSL ECPrivateKey DER
encoding format. This results in the local bootstrapping information
entry being created with the specified key instead of generating a new
random one.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
There could be multiple pending TX operations and if the earlier ones
have used wait_time, but the last one did not, the driver call for
canceling pending wait was not done. This could result in the driver
getting stuck waiting for the previously scheduled wait time and not
being able to do new operations until that. Fix this by canceling the
wait if any of the past offchannel_send_action() calls since the last
offchannel_send_action_done() used non-zero wait_time.
This was showing up as issues in certain DPP Public Action frame
sequences when the same offchannel operation is used with multiple
frames and the last frame in the sequence does not need wait_time.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
The additional SHA-384 and SHA-512 functionality is needed to support
DPP with various ECC curves.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This can be helpful in figuring out what happened if P2P_FIND operation
is unexpectedly rejected.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
wpa_s->p2p_in_provisioning needs to be cleared when group formation
fully completes. The change to postpone GO side handling to the first
data connection in commit 41f853235f
('P2P: Extend group formation timeout on GO to first data connection')
resulted in making this not happen in one P2P Client side case: EAP-WSC
timeout in PBC case. While that is quite special case since it requires
30 second timeout without receiving new EAPOL frames and not getting
disassociation, it can apparently happen in some cases in practice. This
would result in new P2P operations (e.g., P2P_FIND) getting rejected
until wpa_supplicant is restarted.
Fix this by clearing wpa_s->p2p_in_provisioning whenever processing a
group formation failure case. For group formation success,
wpa_s->p2p_in_provisioning is left set to non-zero value to avoid
breaking the earlier limits on the GO side.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This allows the eap_proxy mechanism to be used with multiple SIMs by
following the configured sim_num to index which SIM to use for when
fetching the IMSI through eap_proxy.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This commit is similar to the commit
783c2920cc ('P2P: Check if the pref_freq
reported by the driver supports P2P') but extends the check for
supported pref_freq to wpas_p2p_select_go_freq().
This avoids issues with P2P_GROUP_ADD ending up selecting an unexpected
channel when get_pref_freq_list() (i.e.,
QCA_NL80211_VENDOR_SUBCMD_GET_PREFERRED_FREQ_LIST) is used. Filter the
list by removing channels that do not allow P2P operation at all.
Previously, only the explicitly disallowed channels were removed and
that could have resulted in selecting an operating channel that is not
allowed for P2P and failing to complete the operation to start the
group.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Add NULL checking for EAP name. If it is NULL, do not add the phase2
parameter autheap. This should not happen in practice due to earlier
checks for credential matching, but if there is a code path that would
allow this to be set, it is better to skip setting of the invalid value
and allow automatic selection of the Phase 2 parameters.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Change in any network configuration at runtime will cause flush to
PMKSA cache. For most of the network parameters if there is no change
in value, PMKSA flush is not performed except 'bssid' and 'priority'.
Add 'bssid_hint' to exemption list of avoiding PMKSA flush on change.
This is needed to complete change in commit
43a356b268 ('Provide option to configure
BSSID hint for a network').
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Current DFS domain information of the driver can be used in ap/dfs
to comply with DFS domain specific requirements like uniform spreading
for ETSI domain.
Signed-off-by: Vasanthakumar Thiagarajan <vthiagar@qti.qualcomm.com>
This exposes user configurable option to set bssid_hint for a network.
bssid_hint indicates which BSS has been found a suitable candidate for
initial association for drivers that use driver/firmware-based BSS
selection. Unlike the bssid parameter, bssid_hint does not limit the
driver from selecting other BSSs in the ESS.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Addition of remove_ies() handled the CONFIG_IEEE80211R dependency, but
missed the caller being within CONFIG_FILS as well.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
When reducing the configuration for MACsec/MKA to the bare minimum, so
no EAP authentication, just MACsec/MKA SA use with preshared key/name,
the EAPOL engine is still needed to run the protocol for MKA. Without
any EAP authentication options the IEEE8021X_EAPOL option is not set,
resulting in a non-working Key Agreement Entity.
Therefore the CONFIG_MACSEC block needs to move up and set the
IEEE8021X_EAPOL option.
Signed-off-by: Jaap Keuter <jaap.keuter@xs4all.nl>
In some practical cases, it is useful to suppress joining to node in the
distance. The new field mesh_rssi_threshold could be used as RSSI
threshold for joining.
Signed-off-by: Masashi Honma <masashi.honma@gmail.com>
This patch adds "TDLSCancelChannelSwitch" dbus method on
"fi.w1.wpa_supplicant1.Interface" interface to disable channel switching
with a TDLS peer.
Signed-off-by: Nishant Chaprana <n.chaprana@samsung.com>
This patch adds "TDLSChannelSwitch" dbus method on
"fi.w1.wpa_supplicant1.Interface" interface to enable channel switching
with a TDLS peer.
Signed-off-by: Nishant Chaprana <n.chaprana@samsung.com>
Derive PMK-R0 and the relevant key names when using FILS authentication
for initial FT mobility domain association. Fill in the FT IEs in
(Re)Association Request frame for this.
Signed-off-by: Jouni Malinen <j@w1.fi>
Add support to set ignore assoc disallow to the driver so that the
driver ignores assoc disallowed bit set by APs while connecting. This is
used by drivers that handle BSS selection and roaming internally.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
If the driver provides input on MBO transition candidate handling, the
target value in get_mbo_transition_candidate() can be NULL if the driver
provided BSSID is not found in the wpa_supplicant BSS table. And later
it would be dereferenced. Fix this by adding an explicit check before
dereferencing the pointer.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
wpa_supplicant build with MBO enabled failed in CONFIG_WNM=y was not
specified explicitly. Add the WNM dependency automatically to avoid
needing explicit addition in build configuration.
Signed-off-by: Jouni Malinen <j@w1.fi>
Commit 34f2851902 ('MBO: Parse MBO
ANQP-element on STA') started using the type variable outside
CONFIG_HS20 block, but forgot to remove the ifdef from the variable
declaration.
Signed-off-by: Jouni Malinen <j@w1.fi>
Disconnection due to DISABLE_NETWORK while being connected was resulting
in the AP getting blacklisted. Avoid this by setting own_disconnect_req
on a disconnect request due to DISABLE_NETWORK similarly to the
SELECT_NETWORK disconnection case.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This adds a string "FILS_HLP_SENT" to connect event when HLP is sent
as part of ASSOC/CONNECT request.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
If the uuid configuration parameter is not set, wpa_supplicant generates
an UUID automatically to allow WPS operations to proceed. This was
previously always using an UUID generated from the MAC address. This
commit adds an option to use a random UUID instead. The type of the
automatically generated UUID is set with the auto_uuid parameter: 0 =
based on MAC address (default; old behavior), 1 = random UUID.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Add a new PMKSA cache entry within wpa_supplicant if a driver event from
offloaded FILS shared key authentication indicates a new PMKSA entry was
created.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This keeps the internal ERP information within wpa_supplicant in sync
with the driver when offloading FILS shared key authentication.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Update the internal fils_completed state when offloading FILS shared key
authentication to the driver.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Add FILS/ERP parameters into the driver connect command to support FILS
shared key authentication offload.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This was already done in sme_send_authentication() for the case where
wpa_supplicant SME is used. Similar change is needed for driver-SME to
allow FILS authentication to be offloaded to the driver.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Add support for setting and deleting PMKSA cache entries based on FILS Cache
Identifer. Also additionally add support for sending PMK as part of
SET_PMKSA to enable driver to derive keys in case of FILS shared key
offload using PMKSA caching.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
When using FILS for FT initial mobility domain association, add MDE to
the Authentication frame from the STA to indicate this special case for
FILS authentication.
Signed-off-by: Jouni Malinen <j@w1.fi>
PMKSA_ADD and MESH_PMKSA_ADD command arguments include keying material,
so show it in debug log only if requested to do with the command line -K
argument.
Signed-off-by: Jouni Malinen <j@w1.fi>
In ap_scan=2 mode, wpa_supplicant_assoc_try() did not check whether the
SSID is temporarily disabled before trying to associate and this may
result in an infinite connect/disconnect loop. If the association
succeeds while the SSID is temporarily disabled, wpa_supplicant will
request to deauthenticate and that in turn will cause the SSID to be
temporarily disabled again. Fix that by postponing the association until
the SSID is no longer temporarily disabled.
Signed-off-by: Shaul Triebitz <shaul.triebitz@intel.com>
Without CONFIG_P2P config, the following warning occurs if CONFIG_AP is
enabled for the build:
ap.c: In function ‘wpas_conf_ap_vht’:
ap.c:54:5: warning: unused variable ‘channel’ [-Wunused-variable]
u8 channel = conf->channel;
^
ap.c:53:5: warning: unused variable ‘center_chan’ [-Wunused-variable]
u8 center_chan = 0;
^
Signed-off-by: Masashi Honma <masashi.honma@gmail.com>
This change fixes the following compilation warnings:
wnm_sta.c:1007:4: warning: implicit conversion from enumeration type
'enum mbo_transition_reason' to different enumeration type
'enum mbo_transition_reject_reason' [-Wenum-conversion]
The actual value of both MBO_TRANSITION_REASON_UNSPECIFIED and
MBO_TRANSITION_REJECT_REASON_UNSPECIFIED is 0, so this does not result
in any change in the contents of the frames.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Previously, only the success and failure (to TX) cases were handled. It
is also possible for the driver to transmit the frame, but not receive
an ACK from the recipient. Address that by waiting for a short period of
time for a response. This fixes cases where OSU provider icon fetching
could get stuck if no ACK frame is received.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Do not try to use FILS authentication unless the AP indicates support
for the type the local network profile enforces.
Signed-off-by: Jouni Malinen <j@w1.fi>
This adds an option to configure wpa_supplicant to use the perfect
forward secrecy option in FILS shared key authentication. A new build
option CONFIG_FILS_SK_PFS=y can be used to include this functionality. A
new runtime network profile parameter fils_dh_group is used to enable
this by specifying which DH group to use. For example, fils_dh_group=19
would use FILS SK PFS with a 256-bit random ECP group.
Signed-off-by: Jouni Malinen <j@w1.fi>
This adds STA side addition of OWE Diffie-Hellman Parameter element into
(Re)Association Request frame and processing it in (Re)Association
Response frame.
Signed-off-by: Jouni Malinen <j@w1.fi>
This adds AP side processing for OWE Diffie-Hellman Parameter element in
(Re)Association Request frame and adding it in (Re)Association Response
frame.
Signed-off-by: Jouni Malinen <j@w1.fi>
Since VHT can be toggled explicitly, also expose being able to disable
HT explicitly, without requiring HT overrides. Continue making it
default to enabled though.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Instead of deducing the wide (HT, VHT) channel configuration only
automatically in P2P mode, allow it to be configured in the network
in non-P2P mode.
Also allow all of these parameters to be configured through the control
interface or the configuration file.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Previously, the event "WPS-PBC-ACTIVE" was only generated when
wpa_supplicant is operating as WPS Registrar whereas "WPS-SUCCESS" or
"WPS-TIMEOUT" are generated for both, the Registrar and the Enrollee
roles.
Also generate the event when wpa_supplicant is operating as WPS Enrollee
to allow monitoring the begin and the end of a WPS PBC process.
Signed-off-by: Jörg Krause <joerg.krause@embedded.rocks>
There's no point in making the code use a stack buffer and first copying
the string there, only to copy it again to the output. Make the output
directly use the reason string.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
It is now possible to add neighbor configuration to wnm_bss_query.
Update the auto complete message to reflect that.
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
Add a mechanism to configure the candidates for BTM query candidate list
manually. This can be used to verify AP behavior for various candidates
preferences.
usage:
wnm_bss_query <reason> [neighbor=<BSSID>,<BSSID information>,
<operating class>,<channel number>,
<PHY type>[,<hexdump of optional subelements>]]
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
BSS transition management query and response use a large static buffer
for the frame because the candidate list may require a lot of space.
However, in most cases the actually used space will be much less than
the buffer (since the candidate list is short or completely missing).
Use a dynamically allocated buffer instead and allocate it according
to the actual space needed.
While at it, remove unneeded filling of the MAC header in the Action
frames, since this gets ignored and wpa_drv_send_action() adds the MAC
header anyway.
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
This extends the GAS/ANQP parser in wpa_supplicant to process MBO
ANQP-elements and indicate received Cellular Data Connection Preference
values over the control interface.
When a valid MBO ANQP-element is received, the following control
interface message is sent:
RX-MBO-ANQP <BSSID> cell_conn_pref=<value>
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Previously, ANQP_GET required at least one IEEE 802.11 ANQP-element to
be requested. This is not really necessary, so allow a case where
num_ids == 0 as long as the request includes at least one Hotspot 2.0 or
MBO ANQP-element.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
MBO techspec v0.0_r27 changed the MBO ANQP-element format. The MBO
element in ANQP query should now include an MBO Query List element that
contains a list of MBO elements to query.
Add API to add the MBO Query List to an ANQP query.
Format:
ANQP_GET <addr> <info_id>[,<info_id>]...[,mbo:<subtype>...]
Example for querying neighbor report with MBO cellular data
connection preference:
ANQP_GET <bssid> 272,mbo:2
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
The userspace may want to delay the the first scheduled scan.
This enhances sched_scan to add initial delay (in seconds) before
starting first scan cycle. The driver may optionally choose to
ignore this parameter and start immediately (or at any other time).
This uses NL80211_ATTR_SCHED_SCAN_DELAY to add this via user
global configurable option: sched_scan_start_delay.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
The while (len) loop was updating the next pointer at the end even when
len == 0, i.e., when the new next value won't be used. This could result
in reading one octet beyond the end of the allocated response wpabuf.
While the read value is not really used in practice, this is not correct
behavior, so fix this by skipping the unnecessary next pointer update in
len == 0 case.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
The maximum required size for each Beacon Report element is known in
advance: it is the size of the Beacon Report element fixed fields + the
size of the Reported Frame Body subelement.
Allocate the buffer used for constructing the Beacon Report element
dynamically with the maximum needed size, instead of using a very
large static buffer.
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
This leads to cleaner code overall, and also reduces the size
of the hostapd and wpa_supplicant binaries (in hwsim test build
on x86_64) by about 2.5 and 3.5KiB respectively.
The mechanical conversions all over the code were done with
the following spatch:
@@
expression SIZE, SRC;
expression a;
@@
-a = os_malloc(SIZE);
+a = os_memdup(SRC, SIZE);
<...
if (!a) {...}
...>
-os_memcpy(a, SRC, SIZE);
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Add support for rejecting a BSS transition request using MBO reject
reason codes. A candidate is selected or rejected based on whether it is
found acceptable by both wpa_supplicant and the driver. Also accept any
candidate meeting a certain threshold if disassoc imminent is set in BTM
Request frame.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Add driver interface command using the QCA vendor extensions to check
the driverr whether to accept or reject a BSS transition candidate. For
the reject case, report an MBO reject reason code.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
The parsing code expects non_pref_chan to be non-quoted.
Fix the example in wpa_supplicant.conf not to include
quotes.
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
Previously it was possible for wpa_s->scan_res_handler to remain set to
its old value in case wpa_drv_scan() failed and no retry for the scan
trigger was scheduled (i.e., when last_scan_req == MANUAL_SCAN_REQ).
This could result in getting stuck with the next connection attempt
after a failed "SCAN TYPE=ONLY" operation when wpa_s->scan_res_handler
was set to scan_only_handler().
Fix this by clearing wpa_s->scan_res_handler if wpa_drv_scan() fails and
no retry is scheduled.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
CONFIG_TLS=linux can now be used to select the crypto implementation
that uses the user space socket interface (AF_ALG) for the Linux kernel
crypto implementation. This commit includes some of the cipher, hash,
and HMAC functions. The functions that are not available through AF_ALG
(e.g., the actual TLS implementation) use the internal implementation
(CONFIG_TLS=internal).
Signed-off-by: Jouni Malinen <j@w1.fi>
The reason detail field in non_pref_chan attribute was removed
from MBO draft v0.0_r25. Also oper_class can be 1 character for
few country codes (e.g., country code-UK, channel number-1). So the
shortest channel configuration is 7 characters.
This was missed in the earlier commit
4a83d4b686 ('MBO: Do not add reason_detail
in non_pref_chan attr (STA)') that took care of other changes related to
removal of the reason detail.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
aes-siv.c needs functions from aes-ctr.c and aes-omac1.c, so set
NEED_AES_CTR=y and NEED_AES_OMAC1=y if NEED_AES_SIV is defined. This
fixes some build configuration combinations where either of those
dependencies were not pulled in through other parameters. For example,
some CONFIG_FILS=y cases were impacted.
Signed-off-by: Jouni Malinen <j@w1.fi>
This functionality was originally added in commit
204c9ac4ee ('Extend select_network command
with freq= to reduce scan time') re-using wpa_s->manual_scan_freqs and
MANUAL_SCAN_REQ. That got broken when commit
35d403096e ('Set NORMAL_SCAN_REQ on
SELECT_NETWORK/ENABLE_NETWORK') started overriding wpa_s->scan_req for
SELECT_NETWORK.
Fix this by adding a new scan frequency list specifically for
SELECT_NETWORK so that this does not need to depend on any specific
wpa_s->scan_req value.
Signed-off-by: Jouni Malinen <j@w1.fi>
The PMKSA_GET and PMKSA_ADD commands can now use an optional extra
parameter to fetch and add PMKSA cache entries with the FILS Cache
Identifier.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This allows PMKSA cache entries for FILS-enabled BSSs to be shared
within an ESS when the BSSs advertise the same FILS Cache Identifier
value.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
The ft_completed for FILS authentication case in
wpa_supplicant_event_assoc() depends on something having cleared
portValid so that setting it TRUE ends up authorizing the port. This
clearing part did not happen when using FILS authentication during a
reassociation within an ESS. Fix this by clearing portValid in
sme_send_authentication() just before the keys are cleared (i.e., the
old connection would not be usable anyway).
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
The RSN supplicant implementation needs to be updated to use the new
BSSID whenever doing FILS authentication. Previously, this was only done
when notifying association and that was too late for the case of
reassociation. Fix this by providing the new BSSID when calling
fils_process_auth(). This makes PTK derivation use the correct BSSID.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This adds reason for timeout in event CTRL-EVENT-ASSOC-REJECT whenever
connection failure happens because of timeout. This extends the
"timeout" parameter in the event to include the reason, if available:
timeout=scan, timeout=auth, timeout=assoc.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
IEEE 802.11ax HE changes to include HE IEs in Beacon and Probe Response
frames. These elements are using vendor specific forms for now since the
IEEE 802.11ax draft is not yet finalized and the element contents is
subject to change.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Add IEEE 802.11ax definitions for config, IEEE structures, and
constants. These are still subject to change in the IEEE process.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Let mesh STA A be a STA which has config disable_ht=1.
Let mesh STA B be a STA which has config disable_ht=0.
The mesh STA A and B was connected.
Previously, the mesh STA A sent frame with HT rate even though its HT
was disabled. This commit fixes the issue by checking the local BSS HT
configuration.
Signed-off-by: Masashi Honma <masashi.honma@gmail.com>
The new "SET ric_ies <hexdump>" control interface command can now be
used to request wpa_supplicant to add the specified RIC elements into
Reassociation Request frame when using FT protocol. This is mainly for
testing purposes.
Signed-off-by: Jouni Malinen <j@w1.fi>
This is a copy of the internal HMAC-SHA256 implementation with the hash
block size and output length updated to match SHA384 parameters.
Signed-off-by: Jouni Malinen <j@w1.fi>
This new P2P_SET parameter uses <op_class>:<channel> format and is used
mainly for testing purposes to allow overriding the value of the GO
Negotiation Response frame Operating Channel attribute.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This can be used to override driver get_pref_freq_list() operation for
more convenient testing of preferred frequency list functionality.
Override string format:
<if_type1>:<freq1>,<freq2>,... <if_type2>:...
if_type: 0=STATION, 2=AP, 3=P2P_GO, 4=P2P_CLIENT, 8=TDLS, 9=IBSS
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Previously, the est_throughput comparison was done only when SNR
difference was less than 5 dB. Since the throughput estimation take into
account SNR, this can be done in more cases. For now, add a conservative
2 dB more to the difference so that any SNR difference below 7 dB
results in BSS selection based on throughput estimates.
In addition, the throughput estimates require SNR values to be
available, so separate this from the 5 GHz preference that can be done
based on either SNR or qual values.
Signed-off-by: Jouni Malinen <j@w1.fi>
This allows throughput estimates and 5 GHz preference over 2.4 GHz band
to be used in more cases. The previously used value of 30 was
significantly more conservative than the SNR limits used for the highest
rate in scan_est_throughput() and this resulted in cases where 5 GHz AP
was ignored while SNR with it would have been close to reaching the
maximum TX rate.
Signed-off-by: Jouni Malinen <j@w1.fi>
The published P802.11ai version does not use CRC32 anymore, so remove
inclusion of crc32.o into wpa_supplicant and hostapd builds based on
CONFIG_FILS=y.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This adds new edits from defconfig to android.config. No new build
options are enabled, i.e., this is only bringing in comment updates and
new parameters in commented out form.
Signed-off-by: Jouni Malinen <j@w1.fi>
Add support to set sched scan relative RSSI parameters so that the
drivers can report BSSs after relative comparision with the current
connected BSS. This feature is applicable only when in connected mode.
The below commands can be used to configure relative RSSI parameters
SET relative_rssi <disable|rssi_value>
disable - to disable the feature
rssi_value - amount of relative RSSI in dB
SET relative_band_adjust <band:adjust_value>
band - "2G" or "5G" for 2.4 GHz or 5 GHz respectively
adjust_value - amount of RSSI to be adjusted in dB
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Add an internal flag which indicates to tunneled EAP methods (FAST,
PEAP, TTLS) that they should cache decrypted EAP-SIM/AKA/AKA' requests.
This allows EAP-SIM/AKA/AKA' to be tunneled within these outer methods
while using an external SIM authenticator over the control interface.
Signed-off-by: Paul Stewart <pstew@google.com>
Clean up the event message by removing the ie=<value> parameter when the
IEs are not available instead of printing out "ie=(null)".
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Free the pending frequency list if a second beacon request is received
before the scan for the previous one has been completed.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Sched scan is supported by the kernel also in the connected state, so
allow PNO scan to be issued in the connected state from wpa_supplicant
as well.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
The current implementation of QCA vendor scan does not handle the
simultaneous scan/p2p-scan operations on the same interface due to
missing support for tracking multiple scan cookie values. Hence
serialize such operations on the same interface for now.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
The only_new_results=1 scan parameter was previously set on other scan
cases, but not on the two P2P specific scan triggers. Set this also for
those P2P cases to get consistent behavior after BSS_FLUSH.
This was showing up with number of hwsim P2P test cases maintaining
unexpected scan results from previous test cases due to the flush
operation not really working correctly since the cfg80211 BSS table was
not explicitly cleared.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Add support to send GAS requests with a randomized transmitter address
if supported by the driver. The following control interface commands
(and matching configuration file parameters) can be used to configure
different types of randomization:
"SET gas_rand_mac_addr 0" to disable randomizing TX MAC address,
"SET gas_rand_mac_addr 1" to randomize the complete TX MAC address,
"SET gas_rand_mac_addr 2" to randomize the TX MAC address except for OUI.
A new random MAC address will be generated for every
gas_rand_addr_lifetime seconds and this can be configured with
"SET gas_rand_addr_lifetime <timeout>".
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Previously, VHT capability was default value (=0x0000). This makes
VHT Capabilities Info in VHT Capabilities IE in mesh peering
open/confirm frame 0x0000. This patch fills it with hardware capability.
Signed-off-by: Masashi Honma <masashi.honma@gmail.com>
wpa_group_update_count and wpa_pairwise_update_count can now be used to
set the GTK and PTK rekey retry limits (dot11RSNAConfigGroupUpdateCount
and dot11RSNAConfigPairwiseUpdateCount). Defaults set to current
hardcoded value (4).
Some stations may suffer from frequent deauthentications due to GTK
rekey failures: EAPOL 1/2 frame is not answered during the total timeout
period of currently ~3.5 seconds. For example, a Galaxy S6 with Android
6.0.1 appears to go into power save mode for up to 5 seconds. Increasing
wpa_group_update_count to 6 fixed this issue.
Signed-off-by: Günther Kelleter <guenther.kelleter@devolo.de>
Relying on the group_capab from the P2P peer information can result in
improper information on whether the peer is currently operating as a GO.
However, there is a known implementation in Android that does this.
To reduce issues from this misuse in upper layer to try to determine
whether a specific peer is operationg a group, override the group_capab
value in P2P_PEER output with 0 if there are no BSS entries with the
peer P2P Device as a GO. This is not a perfect information since there
may not have been a recent scan on all channels, but this results in
less issues than trying to decide between new group formation and
joining an existing group based on stale or incorrect information.
Since no upper layer application is really supposed to use the
group_capab field value in P2P_PEER command, this change should not
cause any impact for properly design components and the possibility of
regressions is limited to cases that are already known to work
incorrectly in number of identifiable cases.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Commit 8d1e693186 ('Use estimated
throughput to avoid signal based roaming decision') added a check for
the current BSS estimated throughput being significantly higher than the
selected BSS estimated throughput. However, this case for skipping a
roam used "return 1" which actually allows the roam. Fix this by
returning 0 in this case.
Signed-off-by: Jouni Malinen <j@w1.fi>
To be more consistent with existing hwaddr_aton() and hexstr2bin()
callers, check the return values in this test command.
Signed-off-by: Jouni Malinen <j@w1.fi>
The local custom version of allocating and initializing struct
hostapd_data within wpa_supplicant_mesh_init() is problematic. This has
already missed couple of initialization steps that are required. Instead
of trying to remember to keep this up to date, use
hostapd_alloc_bss_data() so that there is only one place for this
initialization.
This is fixing a recent issue where FILS HLP started using
hapd->dhcp_server and expected that to be initialized to -1. For the
mesh case, that did not happen and when removing the interface, the FILS
HLP implementation ended up unregistering eloop socket for
hapd->dhcp_server (= 0). This could result in missing socket callbacks
for an arbitrary socket.
Signed-off-by: Jouni Malinen <j@w1.fi>
This wpa_drv_if_remove() call was previously modified to fix a different
issue, but that fix resulted in unconditional use of treed memory here
(wpa_supplicant_deinit_iface() frees wpa_s). Make a local copy of
wpa_s->parent to be able to use it after wpa_s is freed. The
mesh_if_created case has wpa_s->parent != wpa_s, so this should be
sufficient way of handling the wpa_drv_if_remove() call here.
Signed-off-by: Jouni Malinen <j@w1.fi>
The new FILS-HLP-RX control interface event is now used to report
received FILS HLP responses from (Re)Association Response frame as a
response to the HLP requests configured with FILS_HLP_REQ_ADD.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This is independent functionality from the core IEEE 802.11 management
handling and will increase significantly in size, so it is cleaner to
maintain this in a separate source code file.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
It was possible to hit this WPA_ASSERT when FST-MANAGER SESSION_REMOVE
command is exececuted when in not-associated state. In
CONFIG_EAPOL_TEST=y builds, this would result in the wpa_supplicant
process being terminated. Convert this WPA_ASSERT to a check that does
not terminate the process, but only rejects the command if wpa_s->bssid
does not match the da argument.
Signed-off-by: Jouni Malinen <j@w1.fi>
Increase the EAPOL RX frame timeout from 100 to 200 ms. This fixes lack
of optimization (i.e., first EAPOL frame dropped) in occasional roaming
and authentication cases on EAP networks if the kernel events can be
reordered and delayed a bit longer.
Signed-off-by: Tomoharu Hatano <tomoharu.hatano@sonymobile.com>
Instead of copying the struct wpa_auth_callbacks, just keep a pointer to
it, keep the context pointer separate, and let the user just provide a
static const structure. This reduces the attack surface of heap
overwrites, since the function pointers move elsewhere.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
If the VHT capability override vht_disabled=1 is used in the network
profile, skip VHT configuration of the local channel.
Signed-off-by: Jouni Malinen <j@w1.fi>
The remote mesh STA which had configuration disable_ht40=1 could have HT
Capabilities element which includes Supported Channel Width Set = 1
(both 20 MHz and 40 MHz operation is supported) even though it had HT
Operation element which includes STA Channel Width = 0 (20 MHz channel
width only). Previously, local peer recognized such a remote peer as 40
MHz band width enabled STA because local peer only checked HT
Capabilities element. This could cause disconnection between
disable_ht40=1 mesh STA and disable_ht40=0 mesh STA. They could
establish a mesh BSS but could not ping with ath9k_htc device. This
commit fixes the issue by refering HT Operation element.
Signed-off-by: Masashi Honma <masashi.honma@gmail.com>
This functionality can be used outside wpa_set_disable_ht40(), so move
the generic part to a helper function.
Signed-off-by: Masashi Honma <masashi.honma@gmail.com>
The new wpa_supplicant control interface commands FILS_HLP_REQ_FLUSH and
FILS_HLP_REQ_ADD can now be used to request FILS HLP requests to be
added to the (Re)Association Request frame whenever FILS authentication
is used.
FILS_HLP_REQ_ADD parameters use the following format:
<destination MAC address> <hexdump of payload starting from ethertype>
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
When AP responds with comeback delay for initial GAS query sent by STA,
gas_query_timeout should be cancelled to avoid GAS failures when
comeback delay is more than GAS_QUERY_TIMEOUT_PERIOD. The
gas_query_timeout is getting registered again when tx_status is received
for GAS comeback request.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
These commnds are mesh version of PMKSA_GET/ADD commands. So the usage
and security risk is similar to them. Refer to
commit 3459381dd2 ('External persistent
storage for PMKSA cache entries') also.
The MESH_PMKSA_GET command requires peer MAC address or "any" as an
argument and outputs appropriate stored PMKSA cache. And the
MESH_PMKSA_ADD command receives an output of MESH_PMKSA_GET and re-store
the PMKSA cache into wpa_supplicant. By using re-stored PMKSA cache,
wpa_supplicant can skip commit message creation which can use
significant CPU resources.
The output of the MESH_PMKSA_GET command uses the following format:
<BSSID> <PMKID> <PMK> <expiration in seconds>
The example of MESH_PMKSA_ADD command is this.
MESH_PMKSA_ADD 02:00:00:00:03:00 231dc1c9fa2eed0354ea49e8ff2cc2dc cb0f6c9cab358a8146488566ca155421ab4f3ea4a6de2120050c149b797018fe 42930
MESH_PMKSA_ADD 02:00:00:00:04:00 d7e595916611640d3e4e8eac02909c3c eb414a33c74831275f25c2357b3c12e3d8bd2f2aab6cf781d6ade706be71321a 43180
This functionality is disabled by default and can be enabled with
CONFIG_PMKSA_CACHE_EXTERNAL=y build configuration option.
Signed-off-by: Masashi Honma <masashi.honma@gmail.com>
This can be used to determine whether the driver supports PMF and if so,
with which group management cipher suites. In addition, add the missing
pairwise and group cipher suite values to the documentation while adding
this new entry there as well.
Signed-off-by: Jouni Malinen <j@w1.fi>
When wpa_supplicant was processing a received Authentication frame (seq
1) from a peer STA for which there was already a TK configured to the
driver, debug log claimed that the PTK gets cleared, but the actual
call to clear the key was actually dropped due to AUTH vs. SUPP set_key
selection. Fix this by explicitly clearing the TK in case it was set
and an Authentication frame (seq 1) is received.
This fixes some cases where EAPOL-Key frames were sent encrypted using
the old key when a peer STA restarted itself and lost the key and had to
re-join the IBSS. Previously, that state required timing out the 4-way
handshake and Deauthentication frame exchange to recover.
Signed-off-by: Jouni Malinen <j@w1.fi>
country[2] needs to be set to ' ' instead of left to '\0' for the case
where wpa_supplicant sets up AP mode operations and includes the Country
element. Currently, this would be only for DFS channels. Without this,
the Beacon frames would go out with incorrect third octet in the country
code.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This control interface command can be used to inject scan results from
test scripts to make it easier to test various scan result processing
operations.
Signed-off-by: Jouni Malinen <j@w1.fi>
Previous version could have used uninitialized char* when a DMG with
invalid capabilities were added to BSS table from scan results.
Signed-off-by: Jouni Malinen <j@w1.fi>
This adds a call to the notify_beacon_loss() callback functions when
beacon loss is detected. In addition, a new CTRL-EVENT-BEACON-LOSS event
is made available through the wpa_supplicant control interface.
Signed-off-by: Jouni Malinen <j@w1.fi>
These parameters are global configuration parameters for wpa_supplicant
and the special control interface SET command handlers for them were
preventing the configuration update. Make this more consistent by
updating the configuration parameter as well since that is what all the
other SET <global config param> commands do.
Signed-off-by: Jouni Malinen <j@w1.fi>
non_pref_chan is a global configuration parameter for wpa_supplicant and
the special control interface SET command handler for it was preventing
the configuration update. Make this more consistent by updating the
configuration parameter as well since that is what all the other SET
<global config param> commands do.
Signed-off-by: Jouni Malinen <j@w1.fi>
Commit 483dd6a5e0 ('Include peer
certificate always in EAP events') added this wpa_supplicant global
configuration parameter, but forgot to add the actual parsing of it, so
there was no way of setting the value.
Signed-off-by: Jouni Malinen <j@w1.fi>
Add a comment to note which fields are expected to be updated by the
driver. In addition, reorder subfield writing to match the order in
which the fields are in the frame.
Signed-off-by: Jouni Malinen <j@w1.fi>
ieee80211_chan_to_freq() is not really meant for conversion of 20 MHz
primary channel numbers for wider VHT channels, so handle those as
special cases here for now.
Signed-off-by: Jouni Malinen <j@w1.fi>
wpabuf_resize() can handle the initial allocation of a wpabuf and all
the other callers of wpas_rrm_report_elem() were already using a pointer
to a pointer and a wpabuf_resize() call. Simplify this by resizing the
wpabuf (if needed) within wpas_rrm_report_elem() instead of having to
calculate the needed size in all the callers. Thsi is also fixing one of
the allocation sizes to use the correct size instead of a size of a
struct that has nothing to do with the allocation (but is larger than
the needed five octets, so does not break anything).
Signed-off-by: Jouni Malinen <j@w1.fi>
There is only a single caller for wpas_rrm_send_neighbor_rep_request()
and it unconditionally uses a callback function, so cb cannot be NULL
here and there is no need for additional complexity and extra code size
to check for it explicitly.
Signed-off-by: Jouni Malinen <j@w1.fi>
Previously, the check was done after we reached the maximum and another
scan was already triggered.
While at it, remove an irrelevant comment that the previous change in
the logic here missed.
Signed-off-by: Beni Lev <beni.lev@intel.com>
Previously, SIM state change with SIM_STATE_ERROR cleared all PMKSA
entries (including non-SIM networks). Limit this to networks which use
SIM-based authentication methods to avoid unnecessarily removal of PMKSA
entries.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
The pending neighbor report state needs to be cleared on error path here
to avoid getting stuck with being unable to perform any additional
neighbor reports during the association.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Allow shorter request since the subelements are optional to include.
Also print the hexdump of the subelements into debug log.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
The requested behavior can be approximated for most use cases even if
the driver does not support reporting exact TSF values for frames.
Enable this capability for all drivers to make beacon report processing
more useful for a common use case.
Signed-off-by: Jouni Malinen <j@w1.fi>
The special parameters for beacon report scan are not needed for the
beacon report when using the beacon table measurement mode. Advertise
support for this case regardless of whether the driver supports the scan
parameters.
Signed-off-by: Jouni Malinen <j@w1.fi>
Beacon Report Radio Measurement is defined in IEEE Std 802.11-2016,
11.11.9.1. Beacon Report is implemented by triggering a scan on the
requested channels with the requested parameters.
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
This conversion will be done several times in the code, so add a helper
function that does this conversion.
Signed-off-by: Avrahams Stern <avraham.stern@intel.com>
Extend verify_channel() to return whether IR is allowed on the channel
or not, and make it a global function so it can be used in other files,
too. This makes this function useful for checking not only if a channel
is supported but also if it is allowed for active and passive scan.
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
Add the following parameters to scan request:
1. Dwell time on each channel.
2. Whether the specified dwell time is mandatory.
In addition, add to scan results info the time that the scan actually
started, and to each scan result the time the beacon/probe was received,
both in terms of TSF of the BSS that the interface that requested the
scan is connected to (if available).
Add flags to indicate whether the driver supports dwell time
configuration and scan information reporting.
This scan configuration and information is required to support beacon
report radio measurement.
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
1. Change the return type to reflect whether building the report
succeeded or failed.
2. Change argument type to rrm_measurement_request_element instead
of raw packet data to ease processing the request.
3. Use already existing function to create the measurement report
and add it to the report buffer.
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
Send measurement report with the mode field set to incapable in response
to measurement requests with unsupported measurement types.
In addition, measurements requests that request parallel measurements
are rejected since these features are not supported.
Measurement request frames with the enable bit set are ignored since
these are not really requesting measurements and are not supported for
now.
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
The length of a Measurement Report frame should be limited by the
maximum allowed MMPDU size (IEEE Std 802.11-2016, 9.6.2.3). Enforce this
size limit, and in case the report elements are longer than the allowed
size, split them between several MPDUs.
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
Extract the code dealing with processing the measurement request
elements to a separate function. This will be needed for beacon report
requests processing.
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
RRM request frame should contain only information elements of type Radio
Measurement Request. Go through all the frame and validate that only
elements of this type are included.
In addition, if a truncated element is encountered, or the element
length field indicates that the element length is more than the
entire frame, abort the request.
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
As support for new RRM measurements will be added, the RRM
implementation will become quite large, so move it to a dedicated file.
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
Commit 4a742011ab ('wpa_supplicant: Handle
LCI request') introduced LCI request parsing in a manner that
incremented the request pointer by four within
wpas_rrm_build_lci_report() without decrementing len correspondingly.
This could potentially result in get_ie() reading four octets beyond the
buffer if a corrupted request is received. This would be applicable only
if the LCI reporting was enabled explicitly ("SET LCI ..." control
interface command).
Fix this by updating the len variable to match the request pointer
changes.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This adds a new wpa_supplicant network profile parameter
mka_priority=0..255 to set the priority of the MKA Actor.
Signed-off-by: Badrish Adiga H R <badrish.adigahr@gmail.com>
This was previously done for SCAN_RESULTS, but the BSS control interface
command did not show a similar flag. In addition, change "WPA2" to "RSN"
for mesh BSS to be consistent with the SCAN_RESULTS output.
Commit 638d945679 ('mesh: Show [MESH] flag
in scan results') did similar changes for SCAN_RESULTS.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This commit extends the BSS commands to include "BSS CURRENT" as a way
to get the current BSS without having to walk the BSS list matching
against BSSID+SSID returned from the STATUS command.
This returns the BSS stored in wpa_s->current_bss.
Signed-off-by: Joel Cunningham <joel.cunningham@me.com>
This registers a new callback to indicate change in SIM state. This
helps to do some clean up (more specifically pmksa_flush) based on the
state change of the SIM. Without this, the reconnection using the cached
PMKSA could happen though the SIM is changed.
Currently eap_proxy_sim_state corresponds to only SIM_STATE_ERROR. This
can be further extended.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This allows user to start P2P Find/Scan on a particular frequency and
then move to scanning social channels. This support is already present
on control socket.
Signed-off-by: Amit Purwar <amit.purwar@samsung.com>
Add p2p_add_cli_chan=1 option to p2p_supplicant.conf to allow Wi-Fi P2P
operating as P2P client on passive scan channels.
In addition, add p2p_add_cli_chan=1 option to wpa_supplicant.conf to
have consistency in P2P channel list. There is a case where P2P channel
list is updated with different channels from p2p0 and wlan0.
Signed-off-by: Tomoharu Hatano <tomoharu.hatano@sonymobile.com>
Commit c579312736 ('Add
PMKSA-CACHE-ADDED/REMOVED events to wpa_supplicant') added new arguments
to these callback functions, but forgot to update the implementations in
preauth_test.c.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This makes both the Probe Response and Beacon frame IEs available to
upper layers if scan results include both IE sets. When the BSS command
mask includes WPA_BSS_MASK_BEACON_IE, a new beacon_ie=<hexdump> entry
will be included in output if the BSS entry has two separate sets of IEs
(ie=<hexdump> showing the Probe Response frame contents and
beacon_ie=<hexdump> the Beacon rame contents).
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
If 20/40 MHz co-ex scan resulted in switching primary and secondary
channels, mesh setup failed to update the frequency parameters for
hostapd side configuration and that could result in invalid secondary
channel configuration preventing creating of the mesh network. This
could happen, e.g., when trying to set up mesh on 5 GHz channel 36 and
co-ex scan finding a BSS on channel 40. Switching the pri/sec channels
resulted in hostapd code trying to check whether channel 32 is
available. Fix this by swapping the channels for hostapd configuration
when needed.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This adds new wpa_supplicant control interface commands PMKSA_GET and
PMKSA_ADD that can be used to store PMKSA cache entries in an external
persistent storage when terminating a wpa_supplicant process and then
restore those entries when starting a new process. The previously added
PMKSA-CACHE-ADDED/REMOVED events can be used to help in synchronizing
the external storage with the memory-only volatile storage within
wpa_supplicant.
"PMKSA_GET <network_id>" fetches all stored PMKSA cache entries bound to
a specific network profile. The network_id of the current profile is
available with the STATUS command (id=<network_id). In addition, the
network_id is included in the PMKSA-CACHE-ADDED/REMOVED events. The
output of the PMKSA_GET command uses the following format:
<BSSID> <PMKID> <PMK> <reauth_time in seconds> <expiration in seconds>
<akmp> <opportunistic>
For example:
02:00:00:00:03:00 113b8b5dc8eda16594e8274df4caa3d4 355e98681d09e0b69d3a342f96998aa765d10c4459ac592459b5efc6b563eff6 30240 43200 1 0
02:00:00:00:04:00 bbdac8607aaaac28e16aacc9152ffe23 e3dd6adc390e685985e5f40e6fe72df846a0acadc59ba15c208d9cb41732a663 30240 43200 1 0
The PMKSA_GET command uses the following format:
<network_id> <BSSID> <PMKID> <PMK> <reauth_time in seconds> <expiration
in seconds> <akmp> <opportunistic>
(i.e., "PMKSA_ADD <network_id> " prefix followed by a line of PMKSA_GET
output data; however, the reauth_time and expiration values need to be
updated by decrementing them by number of seconds between the PMKSA_GET
and PMKSA_ADD commands)
For example:
PMKSA_ADD 0 02:00:00:00:03:00 113b8b5dc8eda16594e8274df4caa3d4 355e98681d09e0b69d3a342f96998aa765d10c4459ac592459b5efc6b563eff6 30140 43100 1 0
PMKSA_ADD 0 02:00:00:00:04:00 bbdac8607aaaac28e16aacc9152ffe23 e3dd6adc390e685985e5f40e6fe72df846a0acadc59ba15c208d9cb41732a663 30140 43100 1 0
This functionality is disabled be default and can be enabled with
CONFIG_PMKSA_CACHE_EXTERNAL=y build configuration option. It should be
noted that this allows any process that has access to the wpa_supplicant
control interface to use PMKSA_ADD command to fetch keying material
(PMK), so this is for environments in which the control interface access
is restricted.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
These allow external program to monitor PMKSA cache updates in
preparation to enable external persistent storage of PMKSA cache.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Configuration file network block with disabled=2 is used for storing
information about a persistent group, so p2p_persitent_group should be
updated according to this when creating a struct wpa_ssid instance. This
will end up using D-Bus persistent network object path for the network.
Signed-off-by: Avichal Agarwal <avichal.a@samsung.com>
Signed-off-by: Kyeong-Chae Lim <kcya.lim@samsung.com>
Supported Operating Classes element and its use is define in the IEEE
802.11 standard and can be sent even when MBO is disabled in the build.
As such, move this functionality out from the CONFIG_MBO=y only mbo.c.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Commit 192ad3d730 ('Interworking: Clear
SCANNING state if no match found') did this for the case where no
network matched credentials, but left the SCANNING state in place if
there were a match, but automatic connection was not enabled. Extend
this to cover the case where INTERWORKING_SELECT is not followed by a
connection attempt so that wpa_state is not left indefinitely to
SCANNING.
This fixes a hwsim test case failure in the following sequence:
ap_anqp_sharing scan_trigger_failure
Signed-off-by: Jouni Malinen <j@w1.fi>
wpa_s->sme.auth_alg could have been left to a previously value other
than WPA_AUTH_ALG_OPEN if IBSS network is used after an association that
used shared key, FT, or FILS authentication algorithm. This could result
in the IBSS setup failing due to incorrect authentication processing
steps.
Fix this by setting wpa_s->sme.auth_alg = WPA_AUTH_ALG_OPEN whenever
starting an IBSS (or mesh, for that matter) network.
Signed-off-by: Jouni Malinen <j@w1.fi>
Commit 8e84921efe ('P2P: Support driver
preferred freq list for Autonomous GO case') introduced this loop to go
through preferred channel list from the driver. The loop does bounds
checking of the index only after having read a value from the array.
That could in theory read one entry beyond the end of the stack buffer.
Fix this by moving the index variable check to be done before using it
to fetch a value from the array.
This code is used only if wpa_supplicant is build with
CONFIG_DRIVER_NL80211_QCA=y and if the driver supports the vendor
extension (get_pref_freq_list() driver op). In addition, the driver
would need to return more than P2P_MAX_PREF_CHANNELS (= 100) preferred
channels for this to actually be able to read beyond the buffer. No
driver is known to return that many preferred channels, so this does not
seem to be reachable in practice.
Signed-off-by: Amit Purwar <amit.purwar@samsung.com>
Signed-off-by: Mayank Haarit <mayank.h@samsung.com>
Commit 370017d968 ('P2P: Use preferred
frequency list from the local driver') introduced this loop to go
through preferred channel list from the driver. The loop does bounds
checking of the index only after having read a value from the array.
That could in theory read one entry beyond the end of the stack buffer.
Fix this by moving the index variable check to be done before using it
to fetch a value from the array.
This code is used only if wpa_supplicant is build with
CONFIG_DRIVER_NL80211_QCA=y and if the driver supports the vendor
extension (get_pref_freq_list() driver op). In addition, the driver
would need to return more than P2P_MAX_PREF_CHANNELS (= 100) preferred
channels for this to actually be able to read beyond the buffer. No
driver is known to return that many preferred channels, so this does not
seem to be reachable in practice.
Signed-off-by: Amit Purwar <amit.purwar@samsung.com>
Signed-off-by: Mayank Haarit <mayank.h@samsung.com>
This makes wpa_supplicant behavior more consistent with FLUSH command to
clear all state. Previously, it was possible for an ongoing scan to be
aborted when the FLUSH command is issued and the scan results from that
aborted scan would still be processed and that would update the BSS
table which was supposed to cleared by the FLUSH command.
This could result in hwsim test case failures due to unexpected BSS
table entries being present after the FLUSH command.
Signed-off-by: Jouni Malinen <j@w1.fi>
Reject a passphrase with control characters instead of trying to write
out an example network configuration block with such control characters
included.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Skipping the scan altogether will hurt auto-reconnect. Also move the PNO
check down since the scan might be canceled for other reasons before we
defer it.
Signed-off-by: Arik Nemtsov <arikx.nemtsov@intel.com>
The way the removal of duplicated (one per frequency) BSS entries in the
cfg80211 scan results were removed in driver_nl80211_scan.c
bss_info_handler() depended on having the full scan results available to
allow iteration through the other entries. This is problematic for the
goal of being able to optimize memory allocations for scan result
fetching in a manner that would not build the full result buffer in
memory.
Move this duplicate removal into bss.c since it has sufficient
information available for doing the same determination of which one of
two BSS entries is more current.
Signed-off-by: Jouni Malinen <j@w1.fi>
wpa_priv did not yet support Beacon frame IEs (res->beacon_ie_len) which
resulted in invalid scan data being accepted in driver_privsep.c. Add
support for res->beacon_ie_len and also fix the validation step to take
this new variable length field into account.
Signed-off-by: Jouni Malinen <j@w1.fi>
wpa_priv has never really been fully up-to-date with the wpa_supplicant
driver interface extensions. This does not seem like something that
would change in the future either, so document this reduced
functionality as a potential drawback.
Signed-off-by: Jouni Malinen <j@w1.fi>
This avoids a theoretical resource leak on exit path if wpa_priv is
killed while there is a wpa_supplicant process using it.
Signed-off-by: Jouni Malinen <j@w1.fi>
This avoids some valgrind warnings about use of uninitialized memory in
cases where a struct may have padding octets between the fields.
Signed-off-by: Jouni Malinen <j@w1.fi>
This gets rid of some dependencies on how extra octets at the end of the
struct sockaddr_un get "uninitialized" consistently by only using the
exact length of the address data from the recvfrom() call. This resolves
number of valgrind warnings about use of uninitialized memory.
Signed-off-by: Jouni Malinen <j@w1.fi>
This is needed to be able to work with many wpa_supplicant use cases,
e.g., due to use of TDLS or RSN pre-authentication needing a separate
l2_packet socket.
Signed-off-by: Jouni Malinen <j@w1.fi>
This commit enhances the existing implementation of abort scan to also
abort concurrent active vendor scans. This is achieved by passing the
the scan_cookie to the driver interface with the intention to abort
the specific scan request. This scan_cookie is returned from the driver
interface when the scan request is scheduled.
This scan_cookie is 0 if the scan is triggered through the upstream
cfg80211 interface. Thus, the scan_cookie is used to determine whether
to abort the cfg80211 or vendor scan request.
Also, the previous implementation of relying on scan_work/p2p_scan_work
for the active work to trigger the abort scan is enhanced to check for
the started state of either of these work operations. This should also
help to abort the concurrent active scan/p2p-scan operations.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This commit enhances the abort scan implementation to also abort the
vendor scan, if one was used to trigger the scan.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
cfg80211 rejects the scans issued with random MAC address if the STA is
in connected state. This resulted in failures when using MAC_RAND_SCAN
while connected (CTRL-EVENT-SCAN-FAILED ret=-95). Enable random MAC
address functionality only if the STA is not in connected state to avoid
this. The real MAC address of the STA is already revealed in the
association, so this is an acceptable fallback mechanism for now.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This commit adds IP address information into GroupStarted event on the
P2P client side like it is sent over the control interface.
Signed-off-by: Nishant Chaprana <n.chaprana@samsung.com>
Previously, wpa_supplicant only supported hardcoded port == 1 in the
SCI, but users may want to choose a different port.
Signed-off-by: Sabrina Dubroca <sd@queasysnail.net>
So that the user can turn encryption on (MACsec provides
confidentiality+integrity) or off (MACsec provides integrity only). This
commit adds the configuration parameter while the actual behavior change
to disable encryption in the driver is handled in the following commit.
Signed-off-by: Sabrina Dubroca <sd@queasysnail.net>
This enables configuring key_mgmt=NONE + mka_ckn + mka_cak.
This allows wpa_supplicant to work in a peer-to-peer mode, where peers
are authenticated by the pre-shared (CAK,CKN) pair. In this mode, peers
can act as key server to distribute keys for the MACsec instances.
This is what some MACsec switches support, and even without HW
support, it's a convenient way to setup a network.
Signed-off-by: Sabrina Dubroca <sd@queasysnail.net>
BoringSSL is the only supported version of SSL, so remove this guard so
we can continue to compile when the flavor.mk is removed.
Signed-off-by: Dmitry Shmidt <dimitrysh@google.com>
This provides more details on BSS selection process in the debug log.
Previously, the BSSs that were not either the current or the selected
one were not necessarily printed at all. Now all BSSs that match the
currently selected network are listed with their frequency and signal
strength details.
Signed-off-by: Jouni Malinen <j@w1.fi>
Previously, the estimated throughput was used to enable roaming to a
better AP. However, this information was not used when considering a
roam to an AP that has better signal strength, but smaller estimated
throughput. This could result in allowing roaming from 5 GHz band to 2.4
GHz band in cases where 2.4 GHz band has significantly higher signal
strength, but still a lower throughput estimate.
Make this less likely to happen by increasing/reducing the minimum
required signal strength difference based on the estimated throughputs
of the current and selected AP. In addition, add more details about the
selection process to the debug log to make it easier to determine whaty
happened and why.
Signed-off-by: Jouni Malinen <j@w1.fi>
Previously, CONFIG_IEEE80211R enabled build that supports FT for both
station mode and AP mode. However, in most wpa_supplicant cases only
station mode FT is required and there is no need for AP mode FT.
Add support to differentiate between station mode FT and AP mode FT in
wpa_supplicant builds by adding CONFIG_IEEE80211R_AP that should be used
when AP mode FT support is required in addition to station mode FT. This
allows binary size to be reduced for builds that require only the
station side FT functionality.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
CONFIG_MBO was defined inside ifdef CONFIG_AP, so when AP support
was not compiled, MBO was not compiled either. However, CONFIG_MBO
is not related AP support, so it should not depend on CONFIG_AP.
Fix this by moving CONFIG_MBO outside of ifdef CONFIG_AP.
Signed-off-by: Avrahams Stern <avraham.stern@intel.com>
This is specific to the macsec_qca driver. The core implementation
shouldn't care about this, and only deal with the complete secure
channel, and pass this down to the driver.
Drivers that have such limitations should take care of these in their
->create functions and throw an error.
Since the core MKA no longer saves the channel number, the macsec_qca
driver must be able to recover it. Add a map (which is just an array
since it's quite short) to match SCIs to channel numbers, and lookup
functions that will be called in every place where functions would get
the channel from the core code. Getting an available channel should be
part of channel creation, instead of being a preparation step.
Signed-off-by: Sabrina Dubroca <sd@queasysnail.net>
When starting ASP provisioning with connection capability set to NEW,
don't create the pending P2P interface as a GO interface because
Go negotiation will determine which side will be the GO and it is
possible that eventually this interface will become the client.
In this case, when the P2P client is started it will start scanning
and do other station specific operations while the interface type
is AP.
Instead, use type WPA_IF_P2P_GROUP when creating the interface which
means the interface type will be determined later.
Signed-off-by: Avrahams Stern <avraham.stern@intel.com>
Previously, a build without IBSS RSN support tried to start/join an IBSS
even if the profile was configured with RSN parameters. This does not
work and resulted in quite confusing debug log. Make this clearer by
explicitly checking for this case and reject the connection attempt with
a clearer debug log entry instead of trying something that is known to
fail.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This commit adds a control interface command to configure the TDLS
trigger mode to the host driver. This TDLS mode is configured through
the "SET tdls_trigger_control" control interface command.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
"GET_CAPABILITY fils" used to return "FILS" based on wpa_supplicant
configuration. This can be made more useful by checking both for
wpa_supplicant and driver support for FILS.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Decrypt the AES-SIV protected elements and verify Key-Auth. Parse and
configure keys to the driver.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Filter out get_pref_freq_list() (i.e.,
QCA_NL80211_VENDOR_SUBCMD_GET_PREFERRED_FREQ_LIST) output in case of
channel negotiation by removing channels that do not allow P2P operation
at all. Previously, only the explicitly disallowed channels were removed
and that could have resulted in selecting an operating channel that is
not allowed for P2P and failing to complete the operation to start the
group.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
If a PMKSA cache entry for the target AP is available, try to use FILS
with PMKSA caching.
If an ERP key for the target AP is available, try to use FILS with
EAP-Initiate/Re-auth added as Wrapper Data element.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This was already done in the case SME in the driver is used, but the SME
code path was resetting the local WPA/RSN IE only for association. While
that was fine for existing use cases, FILS needs a new RSN IE to be set
for PMKSA caching case in Authentication frames, so clear the local IE
before starting new authentication.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This makes it cleaner for the FILS implementation to use the same design
for setting Authentication frame elements as was already done with SAE.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Add network id command completion support for identity, password,
new_password, pin, otp, passphrase, sim and bssid commands.
Signed-off-by: Mikael Kanstrup <mikael.kanstrup@sonymobile.com>
Add list_sta command to print addresses of all stations. Command
added to both wpa_cli and hostapd_cli.
Signed-off-by: Mikael Kanstrup <mikael.kanstrup@sonymobile.com>
With mac_addr=0 and preassoc_mac_addr=1, the permanent MAC address
should be restored for association. Previously this did not happen when
reassociating to the same ESS.
Signed-off-by: Benjamin Richter <br@waldteufel.eu>
Scan results were not propagated to all interfaces if scan results
started a new operation, in order to prevent concurrent operations. But
this can cause other interfaces to trigger a new scan when scan results
are already available. Instead, always notify other interfaces of the
scan results, but note that new operations are not allowed.
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
There are a couple of places in wpa_supplicant/hostapd where qsort() can
be called with a NULL base pointer. This results in undefined behavior
according to the C standard and with some standard C libraries (ARM RVCT
2.2) results in a data abort/memory exception. Fix this by skipping such
calls since there is nothing needing to be sorted.
Signed-off-by: Joel Cunningham <joel.cunningham@me.com>
This was already done for most driver cases, but it is possible that the
BSSID/frequency is not forced if the driver reports BSS selection
capability (e.g., NL80211_ATTR_ROAM_SUPPORT). That could potentially
result in the driver ignoring the BSSID/frequency hint and associating
with another (incorrect) AP for the WPS provisioning step if that
another AP in the same ESS is more preferred (e.g., better signal
strength) by the driver and only one of the APs (the not preferred one)
is in active WPS registrar state.
While most drivers follow the BSSID hint for the initial connection to
an ESS, not doing it here for the WPS provisioning would break the
protocol. Fix this by enforcing a single BSSID/frequency to disallow the
driver from selecting an incorrect AP for the WPS provisioning
association.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This modifies wpa_eapol_key_send() to use AEAD cipher (AES-SIV for FILS
AKMs) to provide both integrity protection for the EAPOL-Key frame and
encryption for the Key Data field. It should be noted that this starts
encrypting the Key Data field in EAPOL-Key message 2/4 while it remains
unencrypted (but integrity protected) in non-FILS cases. Similarly, the
empty Key Data field in EAPOL-Key message 4/4 gets encrypted for AEAD
cases.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This can be used to check whether the running wpa_supplicant version was
built with CONFIG_FILS=y.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
If FILS is supported, indicate that in Probe Request and (Re)Association
Request frames in the Extended Capabilities element.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This adds CONFIG_FILS=y build configuration option and new key
management options for FILS authentication.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
The previous implementation was hardcoded to use 128-bit AES key
(AEAD_AES_SIV_CMAC_256). Extend this by allowing AEAD_AES_SIV_CMAC_384
and AEAD_AES_SIV_CMAC_512 with 192-bit and 256-bit AES keys.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This also implements the macsec_get_capability for the macsec_qca
driver to maintain the existing behavior.
Signed-off-by: Sabrina Dubroca <sd@queasysnail.net>
Clean up the driver interface by passing pointers to struct receive_sc
down the stack to the {create,delete}_recevie_sc() ops, instead of
passing the individual properties of the SC.
Signed-off-by: Sabrina Dubroca <sd@queasysnail.net>
Clean up the driver interface by passing pointers to struct transmit_sc
down the stack to the {create,delete}_transmit_sc() ops, instead of
passing the individual arguments.
Signed-off-by: Sabrina Dubroca <sd@queasysnail.net>
Clean up the driver interface by passing pointers to struct receive_sa
down the stack to the {create,enable,disable}_receive_sa() ops, instead
of passing the individual properties of the SA.
Signed-off-by: Sabrina Dubroca <sd@queasysnail.net>
Clean up the driver interface by passing pointers to struct transmit_sa
down the stack to the {create,enable,disable}_transmit_sa ops, instead
of passing the individual properties of the SA.
Signed-off-by: Sabrina Dubroca <sd@queasysnail.net>
Clean up the driver interface by passing pointers to structs transmit_sa
and receive_sa down the stack to get_receive_lowest_pn(),
get_transmit_next_pn(), and set_transmit_next_pn() ops, instead of
passing the individual arguments.
Signed-off-by: Sabrina Dubroca <sd@queasysnail.net>
This makes it easier to figure out why autoscan is not used even when
being configured through the control interface.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
PNO is sometimes restarted due to changes in scan parameters
(e.g., selected network changed or MAC randomization being
enabled/disabled). Restart is done by stopping PNO and immediately
starting it again. This may result in the SCHED_SCAN_STOPPED event being
received after the request for new PNO, which will make wpa_supplicant
believe PNO is not active although it is actually is. As a result, the
next request to start PNO will fail because PNO is active and should be
stopped first.
Fix this by deferring the request to start PNO until the
SCHED_SCAN_STOPPED event is received in case sched_scan is being
stopped.
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
When scheduled scan stops without the interface request (for example,
driver stopped it unexpectedly), start a regular scan to continue
scanning for networks and avoid being left with no scan at all.
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
In some cases, after a sudden AP disappearing and reconnection to
another AP in the same ESS, if another scan occurs, wpa_supplicant might
try to roam to the old AP (if it was better ranked than the new one)
because it is still saved in BSS list and the blacklist entry was
cleared in previous reconnect. This attempt is going to fail if the AP
is not present anymore and it'll cause long disconnections.
Remove an AP that is probably out of range from the BSS list to avoid
such disconnections. In particular mac80211-based drivers use the
WLAN_REASON_DISASSOC_DUE_TO_INACTIVITY reason code in locally generated
disconnection events for cases where the AP does not reply anymore.
Signed-off-by: David Spinadel <david.spinadel@intel.com>
As the scan channels might need to change when the channel list has been
updated by the kernel. Use the simulated sched_scan timeout
(wpas_scan_restart_sched_scan()) to handle a possible race where an
ongoing sched_scan has stopped asynchronously while trying to restart a
new sched_scan.
Signed-off-by: Arik Nemtsov <arikx.nemtsov@intel.com>
This extends ANQP_GET command to support querying MBO cellular
preference also. The cellular preference can be requested along with
neigbor report by appending mbo:1 to the command arguments.
For example:
ANQP_GET <bssid> 272,mbo:1
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This code sequence was already used at two different places (and an
additional one has been proposed), so add a common helper function to
avoid having to copy-paste this functionality in multiple locations.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
If a scheduled scan is running on select network command,
cancel and reset it before kicking off a regular scan request.
Signed-off-by: Max Stepanov <Max.Stepanov@intel.com>
The reason detail field in non_pref_chan attribute was removed from MBO
draft v0.0_r25, so the STA should not include this field to be compliant
with the latest draft.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
For testing purposes, it is useful to have an option to be able to
reject BTM Request sent by AP in order to verify the AP behavior upon
BTM Request rejection.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Add a testing mechanism to allow association disallowed set by AP to be
ignored. This can be used to verify AP behavior for disallowing a
specific association.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Implement "SET ignore_auth_resp <0/1>" command to simulate auth/assoc
response loss and EAPOL RX packet loss by ignoring corresponding
incoming events.
Signed-off-by: Mikael Kanstrup <mikael.kanstrup@sonymobile.com>
If authentication times out while reassociating to same ESS incorrect
BSSID may end up being blacklisted. Use pending_bssid field on
authentication timeout and deauthentication to ensure the correct AP
gets blacklisted. This is mainly to address cases related to Android
framework roaming behavior.
Signed-off-by: Mikael Kanstrup <mikael.kanstrup@sonymobile.com>
When an interface becomes disabled (e.g., when RF-kill becomes blocked)
we should clear the stored scan results to avoid maintaining stale
information.
Fix this by flushing the BSS entries when an interface becomes
disabled.
Signed-off-by: Moshe Benji <moshe.benji@intel.com>
Previously, struct hostapd_iface sta_seen list head was initialized only
when completing interface setup. This left a window for operation that
could potentially iterate through the list before the list head has been
initialized. While the existing code checked iface->num_sta_seen to
avoid this case, it is much cleaner to initialize the list when struct
hostapd_iface is allocated to avoid any accidental missing of the extra
checks before list iteration.
Signed-off-by: Jouni Malinen <j@w1.fi>
When starting a P2P GO, the struct p2p_go_neg_results may use
persistent_group == 2 to indicate use of persistent reconnect. Setting
ssid->p2p_persistent_group based on this did not take into account this
special case and that ended up in D-Bus code trying to encode 2 as a
DBUS_TYPE_BOOLEAN value which results in an assert from the library. Fix
this by setting ssid->p2p_persistent_group to 0 or 1 instead of raw
params->persistent_group value without any filtering.
This is similar to an earlier fix in commit
112fdee738 ('P2P: Fix D-Bus persistent
parameter in group started event') that addressed another code path in
sending out this D-Bus signal.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Add configuration options that control publishing of fine timing
measurement (FTM) responder and initiator functionality via bits 70, 71
of Extended Capabilities element. Typically, FTM functionality is
controlled by a location framework outside wpa_supplicant. When
framework is activated, it will use wpa_supplicant to configure the
STA/AP to publish the FTM functionality. See IEEE P802.11-REVmc/D7.0,
9.4.2.27.
Signed-off-by: Lior David <qca_liord@qca.qualcomm.com>
Some deployed stations incorrectly consider nsts capability in
(Re)Association Response frame as required capability instead of maximum
capability and if it is greater than station's capability then beamform
will not happen in uplink traffic.
This commit adds support for an optional workaround to use station's
nsts capability in (Re)Association Response frame if the station's nsts
is less than AP by using the use_sta_nsts=1 configuration parameter.
This configuration is introduced in this commit and it is disabled by
default.
Signed-off-by: Tamizh chelvam <c_traja@qti.qualcomm.com>
This patch aims to expose the configuration file path as an interface
property, like is done with the driver and the bridge name. Doing so,
higher layer programs become responsible to recreate interfaces with the
correct configuration file path when programs need to remove them.
Signed-off-by: Jose Blanquicet <blanquicet@gmail.com>
This is a known constant value (CS_ID_LEN, i.e., the length of the EUI64
identifier) and does not need to be provided separately in these
function calls.
Signed-off-by: Sabrina Dubroca <sd@queasysnail.net>
Previously, this was initialized in hostapd_setup_bss() which made it
possible for a REMOVE_NEIGHBOR control interface command to be issued
prior to the list head pointers having been set. That resulted in a NULL
pointer dereference. Fix this by initializing the list head at the time
the data structure gets allocated.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
All the 3 control interfaces: socket based, dbus & binder needs to
perform the same sequence of steps for network add/remove. So, move
these to a common utility method in |wpa_supplicant.c| instead of
duplicating the code everywhere.
Signed-off-by: Roshan Pius <rpius@google.com>
Accoding to the comment of struct wpa_driver_mesh_bss_params, the
max_peer_links parameter should be under that struct.
Signed-off-by: Masashi Honma <masashi.honma@gmail.com>
Previously, secondary channel offset could be non zero even though
disable_ht40=1. This patch fixes it.
Signed-off-by: Masashi Honma <masashi.honma@gmail.com>
Move out the disconnect command handling from |ctrl_iface.c| to
|wpa_supplicant.c| so that it can be reused across the different
control interfaces (socket, dbus & binder).
Signed-off-by: Roshan Pius <rpius@google.com>
The new network profile parameter group_rekey can now be used to specify
the group rekeying internal in seconds for IBSS.
Signed-off-by: Jouni Malinen <j@w1.fi>
If the driver indicates a roamed event with already completed
authorization, altAccept = TRUE could have resulted in the EAP state
machine ending up in the FAILURE state from the INITIALIZE state. This
is not correct behavior and similar cases were already addressed for FT
and WPA-PSK. Fix the offloaded roamed+authorized (EAP/PMKSA caching)
case by doing similar changes to EAPOL/EAP state variable updates during
association event handling.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Add a ".clang-format" file which is pretty close to the rest of
wpa_supplicant code base and reformat the binder codebase.
Signed-off-by: Roshan Pius <rpius@google.com>
Restructure the binder related makefile sections to expose a separate
|libwpa_binder_interface| which can be imported by clients/tests.
While there,
Change the name of the binder service to the name used in the selinux
permissions.
Signed-off-by: Roshan Pius <rpius@google.com>
In preparation for adding further command completion support
to hostapd_cli move some cli related utility functions out of
wpa_cli into a new common cli file.
Signed-off-by: Mikael Kanstrup <mikael.kanstrup@sonymobile.com>
wpas_p2p_persistent_group() returns non-zero for persistent groups. This
value happens to be 2 instead of 1 due to the
P2P_GROUP_CAPAB_PERSISTENT_GROUP value. This ended up with D-Bus code
trying to encode 2 as a DBUS_TYPE_BOOLEAN value which results in an
assert from the library. Fix this by modifying
wpas_p2p_persistent_group() to return 0 or 1 instead of 0 or an
arbitrary non-zero.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This makes wpa_supplicant set default scan IEs to the driver (if the
vendor command is supported). The driver can use these IEs in the scan
requests initiated by the driver itself. Also the driver can merge these
IEs into further scan requests that it receives, in case if the scan
request doesn't carry any of the IEs sent in this command.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Previously, HT capability IE and HT information IE were included in
Beacon and Mesh Peering Open/Confirm frames even if HT is disabled with
disable_ht=1. This patch removes these.
Signed-off-by: Masashi Honma <masashi.honma@gmail.com>
Previously, mesh power management functionality works only with kernel
MPM. Because user space MPM did not report mesh peer AID to kernel,
the kernel could not identify the bit in TIM element. So this patch
reports mesh peer AID to kernel.
Signed-off-by: Masashi Honma <masashi.honma@gmail.com>
The local found variable is not used in this case. Commit
653d227e9f ('MBO: Improve supported
operating class generation') introduced this variable and unnecessarily
set it here. Remove the write-only assignment to silence static
analyzers.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
If no new sme_sa_query_timer() callback is scheculed,
sme_stop_sa_query() needs to be called to allow new SA Query operations
to be started after the failure.
Signed-off-by: Jouni Malinen <j@w1.fi>
This is needed for hwsim test cases to allow multiple STA-initiated SA
Query operations in short amount of time.
Signed-off-by: Jouni Malinen <j@w1.fi>
This is mainly for testing purposes to allow multiple FETCH_OSU ANQP
operations to be ran without having to wait for full scan between each
query.
Signed-off-by: Jouni Malinen <j@w1.fi>
These control interface event message are used by external programs, so
define them a bit more formally in the header file.
Signed-off-by: Jouni Malinen <j@w1.fi>
If base64_encode() fails (e.g., due to memory allocation failure), the
return value needs to be checked against NULL before using the (not
really) returned length value. The error path here ended up reading
uninitialized variable.
Signed-off-by: Jouni Malinen <j@w1.fi>
The previous version did not really work at all and it ended up crashing
if the os_strdup(field->name) call failed.
Signed-off-by: Jouni Malinen <j@w1.fi>
There is no need to maintain separate "return -1;" for each of the
wpa_config_set() calls that cannot really fail in practice.
Signed-off-by: Jouni Malinen <j@w1.fi>
This allows P2P Listen to be offloaded to device to enhance power
saving.
To start P2P listen offload, from wpa_cli interface, issue the command:
p2p_lo_start <freq> <period> <interval> <count>
To stop P2P listen offload, issue the command:
p2p_lo_stop
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Previously, wpa_set_scan_ssids() fully exhausted
wpa_driver_scan_params.ssid list when hidden network IDs are provided
via the control interface. This results in us exceeding the max size for
the list advertised by the driver when we add the "wildcard" scan SSID
entry. So, ensure that we leave space for one more scan SSID entry in
the list when we exit out of wpa_set_scan_ssids().
Signed-off-by: Roshan Pius <rpius@google.com>
Previously, 2.4 GHz operating class 81 was not added for US due to not
all of the channels (1-13 in this operating class) being supported.
Still, this operating class is the main operating class in the global
table for 2.4 GHz and it is the only option for indicating support for
the 2.4 GHz band channels in US.
Change the supported operating class building rules to include all
operating classes for which at least one channel is enabled. In
addition, fix the 80, 80+80, and 160 MHz channel checks (checking the
center frequency channel was failing since it is not a valid 20 MHz
channel).
Signed-off-by: Jouni Malinen <j@w1.fi>
{OPN,CNF,CLS}_IGNR events were removed during P802.11s draft development
process. Replace these with not generating a MPM FSM event. In addition,
add the standard REQ_RJCT event and option to pass in a specific reason
code to mesh_mpm_fsm().
Signed-off-by: Jouni Malinen <j@w1.fi>
During the P802.11s draft development, there were separate LISTEN and
IDLE states. However, the current IEEE 802.11 standards uses only the
IDLE state while the implementation called this LISTEN. Rename the state
in the implementation to match the one used in the standard to avoid
confusion. In addition, rename OPEN_{SENT,RCVD} to OPN_{SNT,RCVD} to
match the exact spelling of these states in the standard.
Signed-off-by: Jouni Malinen <j@w1.fi>
REVmc/D6.0 14.5.5.2.2 (Processing Mesh Peering Open frames for AMPE)
mandates the OPN_RJCT event to be invoked if AES-SIV decryption for
received Mesh Peering Open frame fails. This allows a Mesh Peering Close
frame to be sent in such a case.
Signed-off-by: Jouni Malinen <j@w1.fi>
These optional fields are supposed to be included in the Authenticated
Mesh Peering Exchange element only in Mesh Peering Open frames.
Previously, these were incorrectly included in Mesh Peering
Confirm/Close frames and also required to be present in all these
frames.
While this commit changes the receive processing to ignore the
unexpected extra fields, it should be noted that the previous
implementation required the fields to be present and as such, the fixed
implementation is not compatible with it for secure mesh.
Signed-off-by: Jouni Malinen <j@w1.fi>
If radio_add_work() fails, gas_query_req() ended up freeing the query
payload and returning an error. This resulted in also the caller trying
to free the query payload. Fix this by not freeing the buffer within
gas_query_req() in error case to be consistent with the other error
cases.
Signed-off-by: Jouni Malinen <j@w1.fi>
This function was added with the initial GAS implementation, but there
was no user for it at the time and no clear use now either, so remove
the unused function and the related GAS query reason code.
Signed-off-by: Jouni Malinen <j@w1.fi>
Apply the GAS specific rule of using Protected Dual of Public Action
frame only after having checked that the action code indicates this to
be a GAS response. Previously, non-GAS Public Action frames could have
been incorrectly dropped because of this check if received during an
association with PMF enabled.
Signed-off-by: Jouni Malinen <j@w1.fi>
The GAS-QUERY-DONE event with result=INTERNAL_ERROR was reported on most
other error cases, but the failure triggered by not being able to
transmit a GAS Initial Request stopped the query silently. Make this
more consistent with other error cases by reporting the same event.
Signed-off-by: Jouni Malinen <j@w1.fi>
Now that mesh sets wpa_s->wpa_state = WPA_COMPLETED, it looks like this
getter can get called with wpa_s->current_ssid = NULL. That could result
in NULL pointer dereference, so need to protect that specific case.
Signed-off-by: Jouni Malinen <j@w1.fi>
This signal sends the peer properties to applications for discovered
peers. The signature of this event is "oa{sv}". This event is needed
because the current DeviceFound signal provides only the peer object
path. If there are many peers in range there will be many DeviceFound
signals and for each DeviceFound signal, applications would need to use
GetAll to fetch peer properties. Doing this many times would create
extra load over application as well as over wpa_supplicant, so it is
better to send peer properties in the event so that applications can
extract found peer information without extra steps.
The existing DeviceFound signal is left as-is to avoid changing its
signature.
The issue is not applicable to the control interface because the
P2P-DEVICE-FOUND event includes peer info in it, but over D-Bus
interface DeviceFound provides only the peer object.
Signed-off-by: Nishant Chaprana <n.chaprana@samsung.com>
In mesh interface, the wpa_supplicant state was either
DISCONNECT/SCANNING in non-secured connection or AUTHENTICATING in
secured connection. The latter prevented the scan. Update the
wpa_supplicant state in mesh to be COMPLETED upon initialization. This
is similar to the P2P GO case.
Signed-off-by: Maital Hahn <maitalm@ti.com>
In wpa_supplicant AP mode, allow configuration of the EAP fragment size
using the fragment_size member of network block (wpa_ssid), similar to
the fragment_size in hostapd configuration. bss->fragment_size default
value of 0 is treated specially in some EAP code paths (such as MTU
initialization in eap_pwd_init). In order to preserve the existing
behavior, bss->fragment_size will only be set if the network block
specified a value different from the default which is
DEFAULT_FRAGMENT_SIZE(1398) bytes.
Signed-off-by: Lior David <qca_liord@qca.qualcomm.com>
This is now annotated as be16, so use it as such in all cases instead of
first storing host byte order value and then swapping that to big endian
in other instances of the same structure. This gets rid of number of
sparse warnings.
Signed-off-by: Jouni Malinen <j@w1.fi>
This gets rid of number of sparse warnings and also allows the
compatibility of the declarations to be verified.
Signed-off-by: Jouni Malinen <j@w1.fi>
This gets rid of number of sparse warnings and also allows the
compatibility of the declarations to be verified.
Signed-off-by: Jouni Malinen <j@w1.fi>
In some cases parsing of the mesh scan info for a BSS or the P2P scan
info can fail. One reason can be that the Beacon/Probe Response frame
contained malformed length vendor IEs which are not parsed when adding
to the BSS table. Instead of skipping the whole BSS of the BSS command,
just skip the part that failed to parse.
Signed-off-by: Jonathan Afek <jonathanx.afek@intel.com>
The "Accepting Additional Mesh Peerings bit == 0" means the peer cannot
accept any more peers, so suppress attempt to open a connection to such
a peer.
Signed-off-by: Masashi Honma <masashi.honma@gmail.com>
This moves pairwise, group, and management group ciphers to various mesh
data structures to avoid having to hardcode cipher in number of places
through the code. While CCMP and BIP are still the hardcoded ciphers,
these are now set only in one location.
Signed-off-by: Jouni Malinen <j@w1.fi>
The AMPE element includes number of optional and variable length fields
and those cannot really be represented by a fixed struct
ieee80211_ampe_ie. Remove the optional fields from the struct and
build/parse these fields separately.
This is also adding support for IGTKdata that was completely missing
from the previous implementation. In addition, Key RSC for MGTK is now
filled in and used when configuring the RX MGTK for a peer.
Signed-off-by: Jouni Malinen <j@w1.fi>
The previous implementation was incorrect in forcing the MGTK to be used
as the IGTK as well. Define new variable for storing IGTK and use that,
if set, to configure IGTK to the driver. This commit does not yet fix
AMPE element parsing to fill in this information.
Signed-off-by: Jouni Malinen <j@w1.fi>
This extends the data structures to allow variable length MGTK to be
stored for RX. This is needed as an initial step towards supporting
different cipher suites.
Signed-off-by: Jouni Malinen <j@w1.fi>
Previous implementation was incorrectly using MGTK also as the IGTK and
doing this regardless of whether PMF was enabled. IGTK needs to be a
independent key and this commit does that at the local TX side.
The current AMPE element construction and parsing is quite broken, so
this does not get add the IGTKdata field there.
Signed-off-by: Jouni Malinen <j@w1.fi>
Clean up the mesh_rsn_derive_mtk() function by using proper macros and
pointer to the location within the context block.
Signed-off-by: Jouni Malinen <j@w1.fi>
mesh_rsn_derive_mtk() was hardcoded to use GCMP (even though CCMP was
hardcoded elsewhere) cipher suite selector instead of the selected AKM
suite selector. This resulted in incorrect MTK getting derived. Fix this
by used the SAE AKM suite selector in the input to the KDF.
Signed-off-by: Jouni Malinen <j@w1.fi>
Clean up the mesh_rsn_derive_aek() function by using proper macros and
pointer to the location within the context block.
Signed-off-by: Jouni Malinen <j@w1.fi>
mesh_rsn_derive_aek() was hardcoded to use GCMP (even though CCMP was
hardcoded elsewhere) cipher suite selector instead of the selected AKM
suite selector. This resulted in incorrect AEK getting derived. Fix this
by used the SAE AKM suite selector in the input to the KDF.
Signed-off-by: Jouni Malinen <j@w1.fi>
This is initial step in fixing issues in how PMF configuration for RSN
mesh was handled. PMF is an optional capability for mesh and it needs to
be configured consistently in both hostapd structures (to get proper
RSNE) and key configuration (not included in this commit).
Signed-off-by: Jouni Malinen <j@w1.fi>
Fix possible memory leak in case if WPS is not enabled on the interface
for connection. This path was missed in commit
fae7b37260 ('WPS: Do not expire probable
BSSes for WPS connection').
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
When the BSS count reaches max_bss_count, the oldest BSS will be removed
in order to accommodate a new BSS. Exclude WPS enabled BSSes when going
through a WPS connection so that a possible WPS candidate will not be
lost.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Ditch the legacy syntax and manual engine mangling and just give an
example using simple PKCS#11 URIs that'll work with both GnuTLS and
OpenSSL.
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
IEEE Std 802.11-2012, 10.19 (Public Action frame addressing) specifies
that the wildcard BSSID value is used in Public Action frames that are
transmitted to a STA that is not a member of the same BSS.
wpa_supplicant used to use the actual BSSID value for all such frames
regardless of whether the destination STA is a member of the BSS.
P2P does not follow this rule, so P2P Public Action frame construction
must not be changed. However, the cases using GAS/ANQP for non-P2P
purposes should follow the standard requirements.
Unfortunately, there are deployed AP implementations that do not reply
to a GAS request sent using the wildcard BSSID value. The previously
used behavior (Address3 = AP BSSID even when not associated) continues
to be the default, but the IEEE 802.11 standard compliant addressing
behavior can now be configured with gas_address3=1.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This allows minimal testing with 160 MHz channel with country code ZA
that happens to be the only one with a non-DFS 160 MHz frequency. DFS
with mesh is not yet supported.
Signed-off-by: Jouni Malinen <j@w1.fi>
ssid->frequency cannot be 0 in wpa_supplicant_mesh_init() since
wpas_supplicant_join_mesh() rejects such a configuration.
Signed-off-by: Jouni Malinen <j@w1.fi>
This adds the necessary changes to support extraction and use of the
extended capabilities specified per interface type (a recent
cfg80211/nl80211 extension). If that information is available,
per-interface values will be used to override the global per-radio
value.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Add a new "timeout" argument to the event message if the nl80211 message
indicates that the connection failure is not due to an explicit AP
rejection message. This makes it easier for external programs to figure
out why the connection failed.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
wpa_deinit() got called twice if the random_get_bytes() fails to
generate the MGTK. This resulted in double-freeing the rsn->auth
pointer. Fix this by allowing mesh_rsn_auth_init() handle freeing for
all error cases.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This adds an extra parameter in GroupStarted signal to indicate whether
the created group is Persistent or not. It is similar to the
[PERSISTENT] tag which comes in P2P-GROUP-STARTED over the control
interface.
Signed-off-by: Nishant Chaprana <n.chaprana@samsung.com>
Instead of reporting the memory allocation failure and stopping, run the
scan even if the frequency list cannot be created due to allocation
failure. This allows the wpa_s->reattach flag to be cleared and the scan
to be completed even if it takes a bit longer time due to all channels
getting scanned.
Signed-off-by: Jouni Malinen <j@w1.fi>
If preassoc_mac_addr is used and updating the MAC address fails in
wpas_trigger_scan_cb(), the cloned scan parameters were leaked. Fix that
and also send a CTRL-EVENT-SCAN-FAILED event in this and another error
case.
Signed-off-by: Jouni Malinen <j@w1.fi>
There is no need to have a separate if statement to skip the cases where
phase1 is not set. Just check it with the strstr comparison since this
case is not really used in practice.
Signed-off-by: Jouni Malinen <j@w1.fi>
wpa_s->current_ssid is set to a non-NULL ssid pointer value here, so
there is no need for the extra if statement.
Signed-off-by: Jouni Malinen <j@w1.fi>
The P2P Device interface can only send Public Action frames. Non-Public
Action frames must be sent over a group interface. The previous
implementation sometimes tried to send non-Public Action frames such as
GO Discoverability over the P2P Device interface, however, the source
address of the frame was set to the group interface address so the code
in offchannel.c knew to select the correct interface for the TX.
The check breaks when the P2P Device and group interfaces have the same
MAC address. In this case the frame will be sent over the P2P Device
interface and the send will fail.
Fix this problem in two places:
1. In offchannel, route non-Public Action frames to the GO
interface when the above conditions are met.
2. When a TX_STATUS event arrives on such routed frame, it will
arrive on the GO interface but it must be handled by the P2P Device
interface since it has the relevant state logic.
Signed-off-by: Lior David <qca_liord@qca.qualcomm.com>
This allows using P2PS config method with or without PIN for connection.
wpa_supplicant should internally handle the default PIN "12345670" and
shall also allow connection irrespective of PIN used in P2P_CONNECT.
For example,
1. P2P_CONNECT 02:2a:fb:22:22:33 p2ps
2. P2P_CONNECT 02:2a:fb:22:22:33 xxxxxxxx p2ps
Where the second one is maintained for backwards compatibility.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
work->type was pointing to the allocated work->ctx buffer and the debug
print in radio_work_free() ended up using freed memory if a started
external radio work was removed as part of FLUSH command operations. Fix
this by updating work->type to point to a constant string in case the
dynamic version gets freed.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Add a new parameter wps_disabled to network block (wpa_ssid). This
parameter allows WPS functionality to be disabled in AP mode.
Signed-off-by: Lior David <qca_liord@qca.qualcomm.com>
While this is unlikely to make any practical difference, it is better to
keep consistent with hostapd configuration parser.
Signed-off-by: Jouni Malinen <j@w1.fi>
If the network profile key_mgmt parameter was not set, wpa_supplicant
defaulted to enabling both WPA-PSK and WPA-EAP. This is not correct for
AP mode operations, so remove WPA-EAP in such a case to fix WPA-PSK
without explicit key_mgmt parameter.
Signed-off-by: Jouni Malinen <j@w1.fi>
wpa_supplicant was starting P2P group processing for all AP mode
interfaces in CONFIG_P2P=y builds. This is unnecessary and such
operations should be enabled only for actual GO interfaces.
Signed-off-by: Jouni Malinen <j@w1.fi>
The NL80211_CMD_WIPHY_REG_CHANGE can be handled by any of the
interfaces that are currently controlled by the wpa_supplicant.
However, some applications expect the REGDOM_CHANGE event to be
sent on the control interface of the initially added interface
(and do not expect the event on any of child interfaces).
To resolve this, when processing NL80211_CMD_WIPHY_REG_CHANGE,
find the highest parent in the chain, and use its control interface
to emit the CTRL-EVENT-REGDOM-CHANGE event.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
This makes it easier to write hwsim test cases to verify management
frame processing sequences with dropped or modified frames. When
ext_mgmt_frame_handling is used, this new command can be used to request
wpa_supplicant to process a received a management frame, e.g., based on
information reported in the MGMT-RX events.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
IEEE Std 802.11-2012 13.5.6.3 State transitions require an action
sending SETKEYS primitive to MAC when OPN_ACPT event occurs in CNF_RCVD
state in case of AMPE is used, but since MTK calculation is missed in
this condition, all zero valued key are passed to MAC and cause unicast
packet decryption error. This could happen if the first transmission of
plink Open frame is dropped and Confirm frame is processed first
followed by retransmitted Open frame.
Fix this by calculating the MTK also in this sequence of unexpected
messages.
Signed-off-by: Peter Oh <poh@qca.qualcomm.com>
IEEE Std 802.11-2012 Table 13-2, MPM finite state machine requires to
clear retryTimer when CNF_ACPT event occurs in OPN_SNT state which is
missing, so add it to comply with the standard.
This was found while debugging an MTK issue and this commit fixes a
potential issue that mesh sends invalid event (PLINK_OPEN) which will
lead another invalid timer register such as MeshConfirm Timer. This
behaviour might lead to undefined mesh state.
Signed-off-by: Peter Oh <poh@qca.qualcomm.com>
Instead of hardcoding "ad-hoc" in the array of supported capabilities,
add this only if the driver indicates support for IBSS.
Signed-off-by: Saurav Babu <saurav.babu@samsung.com>
wpas_ap_pmksa_cache_list() and wpas_ap_pmksa_cache_flush() should be
under the #ifdef since they're only called for the control iface and
use functionality that otherwise isn't available.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Since ieee80211w=2 is an explicit configuration to wpa_supplicant, the
connection attempt for such non-PMF (non-RSN) capable networks should be
skipped.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
PMF is available only with RSN and pmf=2 could have prevented open
network connections. Change the global wpa_supplicant pmf parameter to
be interpreted as applying only to RSN cases to allow it to be used with
open networks.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Many of the global configuration parameters are written as strings
without filtering and if there is an embedded newline character in the
value, unexpected configuration file data might be written.
This fixes an issue where wpa_supplicant could have updated the
configuration file global parameter with arbitrary data from the control
interface or D-Bus interface. While those interfaces are supposed to be
accessible only for trusted users/applications, it may be possible that
an untrusted user has access to a management software component that
does not validate the value of a parameter before passing it to
wpa_supplicant.
This could allow such an untrusted user to inject almost arbitrary data
into the configuration file. Such configuration file could result in
wpa_supplicant trying to load a library (e.g., opensc_engine_path,
pkcs11_engine_path, pkcs11_module_path, load_dynamic_eap) from user
controlled location when starting again. This would allow code from that
library to be executed under the wpa_supplicant process privileges.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Most of the cred block parameters are written as strings without
filtering and if there is an embedded newline character in the value,
unexpected configuration file data might be written.
This fixes an issue where wpa_supplicant could have updated the
configuration file cred parameter with arbitrary data from the control
interface or D-Bus interface. While those interfaces are supposed to be
accessible only for trusted users/applications, it may be possible that
an untrusted user has access to a management software component that
does not validate the credential value before passing it to
wpa_supplicant.
This could allow such an untrusted user to inject almost arbitrary data
into the configuration file. Such configuration file could result in
wpa_supplicant trying to load a library (e.g., opensc_engine_path,
pkcs11_engine_path, pkcs11_module_path, load_dynamic_eap) from user
controlled location when starting again. This would allow code from that
library to be executed under the wpa_supplicant process privileges.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Spurious newlines output while writing the config file can corrupt the
wpa_supplicant configuration. Avoid writing these for the network block
parameters. This is a generic filter that cover cases that may not have
been explicitly addressed with a more specific commit to avoid control
characters in the psk parameter.
Signed-off-by: Paul Stewart <pstew@google.com>
WPA/WPA2-Personal passphrase is not allowed to include control
characters. Reject a passphrase configuration attempt if that passphrase
includes an invalid passphrase.
This fixes an issue where wpa_supplicant could have updated the
configuration file psk parameter with arbitrary data from the control
interface or D-Bus interface. While those interfaces are supposed to be
accessible only for trusted users/applications, it may be possible that
an untrusted user has access to a management software component that
does not validate the passphrase value before passing it to
wpa_supplicant.
This could allow such an untrusted user to inject up to 63 characters of
almost arbitrary data into the configuration file. Such configuration
file could result in wpa_supplicant trying to load a library (e.g.,
opensc_engine_path, pkcs11_engine_path, pkcs11_module_path,
load_dynamic_eap) from user controlled location when starting again.
This would allow code from that library to be executed under the
wpa_supplicant process privileges.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
When the P2P Device interface is used and an existing interface is used
for P2P GO/Client, the P2P Device configuration was not cloned to the
configuration of the existing interface. Thus, configuration parameters
such as idle_group_time, etc., were not propagated to the P2P GO/Client
interface.
Handle this by copying all configuration parameters of the P2P device
interface to the reused interface, with the following exceptions:
1. Copy the NFC key data only if it was not set in the configuration
file.
2. The WPS string fields are set only if they were not previously set
in the configuration of the destination interface (based on the
assumption that these fields should be identical among all
interfaces).
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
Use the p2pdev pointer instead of the parent pointer to comply with the
flows when a dedicated P2P Device interface is used and
p2p_no_group_iface == 1 (in which case the parent of the reused
interface isn't necessary the same as p2pdev).
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
On receiving a WNM BSS Transition Management Request frame with a
candidate list, fetch the latest scan results from the kernel to see if
there are any recent scan results for the candidates and initiate a
connection if found. This helps to avoid triggering a new scan in cases
where a scan initiated by something else (e.g., an internal beacon
measurement report functionality in a driver) has processed Beacon or
Probe Response frames without wpa_supplicant having received a
notification of such an update yet.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
systemd service files were supplied with old D-Bus bus name. After
service activation systemd was waiting for appearance of specified bus
name to consider it started successfully. However, if wpa_supplicant was
compiled only with the new D-Bus interface name, systemd didn't notice
configured (old) D-Bus bus name appearance. In the end, service was
considered malfunctioning and it was deactivated.
Update systemd service BusName property according to supported D-Bus
interface version.
Signed-off-by: Marcin Niestroj <m.niestroj@grinn-global.com>
This allows local GO to fetch the P2P Interface Address of a P2P Client
in the group based on the P2P Device Address for the client. This
command should be sent only on a group interface (the same peer may be
in multiple concurrent groups).
Usage:
P2P_GROUP_MEMBER <P2P Device Address>
Output:
<P2P Interface Address>
Signed-off-by: Purushottam Kushwaha <pkushwah@qti.qualcomm.com>
Trigger an event when wpa_supplicant accepts an invitation to re-invoke
a persistent group. Previously wpa_supplicant entered group formation
without triggering any specific events and it could confuse clients,
especially when operating with a driver that does not support
concurrency between P2P and infrastructure connection.
Signed-off-by: Lior David <qca_liord@qca.qualcomm.com>
Parse a received neighbor report and report for each neighbor report the
data received for it:
RRM-NEIGHBOR-REP-RECEIVED bssid=<BSSID> info=0x<hex> op_class=<class> chan=<chan> [lci=hex] [civic=hex]
Note that this modifies the previous format that originally reported
only the length of the received frame.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Handle radio measurement request that contains LCI request. Send
measurement report based on a configurable LCI report element. The LCI
report element is configured over the control interface with
SET lci <hexdump of the element>
and cleared with
SET lci ""
Signed-off-by: David Spinadel <david.spinadel@intel.com>
Process Neighbor Report Request frame and send Neighbor Report Response
frame based on the configured neighbor report data.
Signed-off-by: David Spinadel <david.spinadel@intel.com>
Add a configurable neighbor database that includes the content of
Nighbor Report element, LCI and Location Civic subelements and SSID.
All parameters for a neighbor must be updated at once; Neighbor Report
element and SSID are mandatory, LCI and civic are optional. The age of
LCI is set to the time of neighbor update.
The control interface API is:
SET_NEIGHBOR <BSSID> <ssid=SSID> <nr=data> [lci=<data>] [civic=<data>]
To delete a neighbor use:
REMOVE_NEIGHBOR <BSSID> <SSID>
Signed-off-by: David Spinadel <david.spinadel@intel.com>
Add an option to request LCI and Location Civic Measurement in Neighbor
Report Request frame, as described in IEEE P802.11-REVmc/D5.0, 9.6.7.6.
Note: This changes the encoding format of the NEIGHBOR_REP_REQUEST
ssid=<val> parameter. This used to be parsed as raw SSID data which is
problematic for accepting additional parameters. The new encoding allows
either a string within double-quotation marks or a hexdump of the raw
SSID.
Thew new format:
NEIGHBOR_REP_REQUEST [ssid=<SSID>] [lci] [civic]
Signed-off-by: David Spinadel <david.spinadel@intel.com>
Add a function that parses SSID in text or hex format. In case of the
text format, the SSID is enclosed in double quotes. In case of the hex
format, the SSID must include only hex digits and not be enclosed in
double quotes. The input string may include other arguments after the
SSID.
Signed-off-by: David Spinadel <david.spinadel@intel.com>
Make the function available as part of the wpabuf API.
Use this renamed function where possible.
Signed-off-by: David Spinadel <david.spinadel@intel.com>
The new VENDOR_ELEM value 14 can now be used to add a vendor element
into Probe Request frames used by non-P2P active scans.
For example:
VENDOR_ELEM_ADD 14 dd05001122330a
and to clear that:
VENDOR_ELEM_REMOVE 14 *
Signed-off-by: Jouni Malinen <j@w1.fi>
When a station starts an association to a Hotspot 2.0 network, request
the driver to do the following, based on the BSS capabilities:
1. Enable gratuitous ARP filtering
2. Enable unsolicited Neighbor Advertisement filtering
3. Enable unicast IP packet encrypted with GTK filtering if
DGAF disabled bit is zero
Clear the filter configuration when the station interface is
disassociated.
Signed-off-by: Matti Gottlieb <matti.gottlieb@intel.com>
Add a new function declaration that will allow wpa_supplicant to request
the driver to configure data frame filters for specific cases.
Add definitions that will allow frame filtering for stations as
required by Hotspot 2.0:
1. Gratuitous ARP
2. Unsolicited NA
3. Unicast IP packets encrypted with GTK
Signed-off-by: Matti Gottlieb <matti.gottlieb@intel.com>
Add a new value 2 to the pbss parameter of wpa_ssid structure, which
means "don't care". This value is used in infrastructure mode to request
connection to either AP or PCP, whichever is available in the scan
results. The value is also used in regular WPS (not P2P group formation)
to make WPS work with devices running as either AP or PCP.
Signed-off-by: Lior David <qca_liord@qca.qualcomm.com>
With the only callers in wpas_{start,stop}_pno() moved into scan.c,
there is no need to call these helper functions from outside scan.c
anymore.
Signed-off-by: Jouni Malinen <j@w1.fi>
Commit dd271857a5 ('Skip normal scan when
PNO is already in progress') fixed issues with normal scans getting
rejected by the driver when PNO scan is already running. The part about
skipping such a scan request is fine, but the part about clearing
wpa_s->pno back to 0 in EVENT_SCHED_SCAN_STOPPED handler is problematic.
If PNO is stopped ("SET pno 0") and then restarted ("SET pno 1")
immediately, it is possible for the EVENT_SCHED_SCAN_STOPPED event from
the stopping part to be received only after the new PNO instance has
been started. This would have resulted in clearing wpa_s->pno and the
driver and wpa_supplicant getting out of sync. This would then prevent
PNO from being stopped with "SET pno 0" (that fails if wpa_s->pno == 0).
Fix this race condition by reverting the wpa_s->pno = 0 addition from
the EVENT_SCHED_SCAN_STOPPED handler.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This adds use of the driver capability (instead of hardcoded
WPAS_MAX_SCAN_SSIDS) in wpas_start_pno() similarly to what was already
done in wpa_supplicant_req_sched_scan().
Signed-off-by: Dmitry Shmidt <dimitrysh@google.com>
This commit implements the methods defined in Supplicant service:
1. CreateInterface
2. RemoveInterface
3. GetInterface
The binder service returns the corresponding iface binder object
references which can be used by clients to control a specific
interface.
Signed-off-by: Roshan Pius <rpius@google.com>
Create the skeletal binder interface for wpa_supplicant. The interface
hierarchy is based off the existing dbus
interface(https://w1.fi/wpa_supplicant/devel/dbus.html).
Since we use libbinder, the binder interface codebase needs to be
written in C++ and can only be compiled on Android platform for now.
The aidl files define binder RPC interfaces. The Android build system
generates the corresponding C++ interface classes which needs to be
implemented by the server process.
The clients can obtain a reference to the binder service (root object)
using:
android::String16 service_name("fi.w1.wpa_supplicant");
android::sp<android::IBinder> binder =
android::defaultServiceManager()->getService(service_name);
Once a reference to the root object is retrieved, the clients can
obtain references to other RPC objects using that root object methods.
Signed-off-by: Roshan Pius <rpius@google.com>
This struct in the union is empty, but the design of using a zero-length
u8 array here is not fully compatible with C++ and can result in
undesired compiler warnings. Since there are no non-IE fields in the
Probe Request frames, get the location of the variable length IEs simply
by using the pointer to the frame header and the known header length.
Signed-off-by: Jouni Malinen <j@w1.fi>
This avoids unnecessary flushing of the PMKSA cache entry and EAP
session data when processing SET_NETWORK commands that set a network
profile parameter to the same value that the parameter already has.
Introduce a new wpa_config_set() and wpa_config_set_quoted() return
value (==1) signifying that the new value being set for the
corresponding field equals to the already configured one so that the
caller can determine that nothing changed in the profile.
For now, this does not cover all the network profile parameters, but
number of the most commonly used parameters are included to cover the
Android use cases where the framework may have issued SET_NETWORK
commands that would have unnecessarily prevented use of PMKSA caching or
EAP fast reauthentication.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
wpa_supplicant_global_ctrl_iface_receive() did not handle the from
address properly for the IPv6 case. This was broken by commit
d60886cdaf ('wpa_supplicant: Add monitor
support for global UDP ctrl_iface').
Signed-off-by: Jouni Malinen <j@w1.fi>
All that the kernel header was doing here is defining SIOCOUTQ to be
TIOCOUTQ. Instead of pulling in the header, we might as well use
TIOCOUTQ directly.
Signed-off-by: Jouni Malinen <j@w1.fi>
Fix two problems with storage of 60 GHz P2P persistent groups:
1. pbss flag was not stored in the network block.
2. When recreating the persistent group from storage,
in addition to the missing pbss flag, the pairwise_cipher and
group_cipher were initialized to CCMP which does not work
in 60 GHz since the default in 60 GHz should be GCMP.
Signed-off-by: Lior David <qca_liord@qca.qualcomm.com>
The initial connection to an ESS was already explicitly increasing the
likelihood of picking a 5 GHz BSS. While the throughput estimation is
likely to do same for the roaming decision, it might be possible that
that does not cover all cases. Add couple of dB extra preference for 5
GHz in case the roaming decision falls back to comparing signal levels.
Signed-off-by: Jouni Malinen <j@w1.fi>
This allows the SME-in-the-driver case to get similar information about
reassociation that was already available for the SME-in-wpa_supplicant
case.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Reject a BSS transition management candidate if it does not match the
current network profile, e.g., due to incompatible security parameters.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
The new wpa_supplicant command line argument -M can be used to describe
matching rules with a wildcard interface name (e.g., "wlan*").
This is very useful for systems without udev (Linux) or devd (FreeBSD).
Signed-off-by: Roy Marples <roy@marples.name>
Interface additions/removals are not guaranteed to be for the driver
listening to the kernel events. As such, send the events to
wpa_supplicant_event_global() which can then pick the correct interface
registered with wpa_supplicant to send the event to.
Signed-off-by: Roy Marples <roy@marples.name>
Commit 1889af2e0f ('VLAN: Separate station
grouping and uplink configuration') added an ap_sta_set_vlan() function
that gets called from pmksa_cache_auth.c. This broke CONFIG_IBSS_RSN=y
build if src/ap/sta_info.c did not get included in the build, i.e., if
CONFIG_AP=y was not set.
Fix this by making the ap_sta_set_vlan() call conditional on
CONFIG_NO_VLAN being undefined and define this for CONFIG_IBSS_RSN=y
builds. This is fine for wpa_supplicant since CONFIG_AP=y case was
already defining this. For hostapd, this function call is not needed for
CONFIG_NO_VLAN case either.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
While p2p_group_add ctrl_interface name could be derived from the main
interface (simple p2p_group_add command), we failed to bind the same UDP
port. Fix this problem and also update the correct ctrl_interface name
(port decrement).
Signed-off-by: Janusz Dziedzic <janusz.dziedzic@tieto.com>
Previously, BLOCKED state duration slightly increased up to 3600. Though
the BLOCKED state could be canceled by ap_handle_timer(). Because the
timer timeouts in ap_max_inactivity(default=300sec) and remove STA
objects (the object retains BLOCKED state).
This patch re-designs my commit bf51f4f82b
('mesh: Fix remaining BLOCKED state after SAE auth failure') to replace
mesh_auth_block_duration by ap_max_inactivity and remove incremental
duration.
Signed-off-by: Masashi Honma <masashi.honma@gmail.com>
This patch add functionality of mesh SAE PMKSA caching. If the local STA
already has peer's PMKSA entry in the cache, skip SAE authentication and
start AMPE with the cached value.
If the peer does not support PMKSA caching or does not have the local
STA's PMKSA entry in the cache, AMPE will fail and the PMKSA cache entry
of the peer will be removed. Then STA retries with ordinary SAE
authentication.
If the peer does not support PMKSA caching and the local STA uses
no_auto_peer=1, the local STA can not retry SAE authentication because
NEW_PEER_CANDIDATE event cannot start SAE authentication when
no_auto_peer=1. So this patch extends MESH_PEER_ADD command to use
duration(sec). Throughout the duration, the local STA can start SAE
authentication triggered by NEW_PEER_CANDIDATE even though
no_auto_peer=1.
This commit requires commit 70c93963ed
('SAE: Fix PMKID calculation for PMKSA cache'). Without that commit,
chosen PMK comparison will fail.
Signed-off-by: Masashi Honma <masashi.honma@gmail.com>
This extends the wpa_supplicant PMKSA_FLUSH control interface command to
allow the PMKSA list from the authenticator side to be flushed for AP
and mesh mode. In addition, this adds a hostapd PMKSA_FLUSH control
interface command to flush the PMKSA entries.
Signed-off-by: Masashi Honma <masashi.honma@gmail.com>
This extends the wpa_supplicant PMKSA control interface command to allow
the PMKSA list from the authenticator side to be listed for AP and mesh
mode. In addition, this adds a hostapd PMKSA control interface command
to show the same list for the AP case.
Signed-off-by: Masashi Honma <masashi.honma@gmail.com>
This allows a mesh peer connection to be initiated manually in
no_auto_peer mesh networks.
Signed-off-by: Natsuki Itaya <Natsuki.Itaya@jp.sony.com>
Signed-off-by: Masashi Honma <masashi.honma@gmail.com>
This command allows the specified mesh peer to be disconnected.
Signed-off-by: Natsuki Itaya <Natsuki.Itaya@jp.sony.com>
Signed-off-by: Masashi Honma <masashi.honma@gmail.com>
This group capability bit was previously added unconditionally which
could result in the P2P Client assuming the functionality is available
even though the GO would always reject the request (not reply to it with
an assigned IP address) during the 4-way handshake.
Fix this by advertising the capability only if the GO configuration
allow IP address assignment to be completed.
Signed-off-by: Jouni Malinen <j@w1.fi>
The 4-way handshake fails with the error "WPA: No wpa_ie set - cannot
generate msg 2/4" while connecting to OSEN network with drivers that
indicate used Association Request frame elements because OSEN IE is not
handled in wpa_supplicant_event_associnfo() if data->assoc_info.req_ies
is not NULL.
Signed-off-by: Daichi Ueura <daichi.ueura@sonymobile.com>
The bssid and priority parameters in a network block do not have any
effect on the validity of an EAP session entry, so avoid flushing the
cached session when only these parameters are changed. This is mainly to
allow forced roaming or network selection changes without causing fast
reauthentication to be disabled if the changes are done during RSN
association that used EAP.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
If the configured credential includes a username without '@' (i.e., no
realm) in it and a realm, combine these to form the EAP-Request/Identity
value as "<username>@<realm>" for EAP-TLS. This was already done for
EAP-TTLS as part of the anonymous NAI conversion, but EAP-TLS could have
ended up using a username without any realm information which would be
unlikely to work properly with roaming cases.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
The existing implementation in p2p_ctrl_set used a hard-coded operating
class 81 which is only suitable for the social channels in the 2.4 GHz
band, and will not work for the social channel in the 60 GHz band.
Extend this by adding an optional op_class argument to P2P_SET
listen_channel. If not specified, use the default value of 81 to match
existing behavior.
Signed-off-by: Lior David <qca_liord@qca.qualcomm.com>
(Re)Association Response frame with status code other than 0 is now
notified over DBUS as a part of PropertiesChanged signal. This can be
used by application in case AP is denying association with status code
17 (band steering) so that it does not interfere in the BSSID selection
logic of wpa_supplicant.
Signed-off-by: Naveen Singh <nasingh@google.com>
"INTERFACES ctrl" can now be used to fetch a list of network interfaces
and their control interfaces, e.g., to fetch the UDP port information
for the control interface.
Signed-off-by: Janusz Dziedzic <janusz.dziedzic@tieto.com>
Extend the previously per-interface UDP ctrl_iface functions
(attach/detach/send) to support operations on the global interface as
well.
Signed-off-by: Janusz Dziedzic <janusz.dziedzic@tieto.com>
This allows the UDP port to be set for the per-interface and global
control interfaces. The format is: udp:<port_no>
For example:
wpa_supplicant -Dnl80211 -ddt -g udp:9888
And in the configuration file:
ctrl_interface=udp:9877
Signed-off-by: Janusz Dziedzic <janusz.dziedzic@tieto.com>
Make sure wpas_p2p_init_go_params() respects the p2p_ignore_shared_freq
configuration option. Choose currently used frequencies only if this
option is not set, or if there are no unused channels left.
Signed-off-by: Eliad Peller <eliad@wizery.com>
When p2p_find is stopped, send request to the driver
in order to cancel an ongoing scan if there is one.
Signed-off-by: Ben Rosenfeld <ben.rosenfeld@intel.com>
An interface can be disabled while it has an ongoing scan request.
In such a case, when the scan results notification is received,
it was being ignored (as the interface is already disabled) so the
scan state was not cleared. This can cause undetermined behavior
for the next scan request.
To handle this, clear the scan state when EVENT_SCAN_RESULTS is
received and the interface is disabled.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Verify that when the Candidate List Included bit is set in a BSS
Transition Management Request frame, the candidate list actually
includes at least one candidate. If no candidates are included, reject
the request without scanning.
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
In BSS Transition Management Request frame, it is possible that vendor
specific IEs are included after the candidate list. In this case the
candidates count was incremented for each IE although the candidate list
is already over which could result in adding all zeros candidates into
the neighbor list.
Fix that by incrementing the candidates count only for neighbor report
elements.
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
In case wpa_cli is started with an option to execute an action script,
but no interface is specified, wpa_cli might crash in wpa_cli_exec() if
arg1 == NULL. Fix this be setting arg1 = "global".
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
The libcrypto and libssl modules (and their respective static and host
versions) use LOCAL_EXPORT_C_INCLUDE_DIRS thus just including the module
is sufficient.
Signed-off-by: Dmitry Shmidt <dimitrysh@google.com>
Clear wpa_s->fetch_anqp_in_progress when osu-providers.txt can't be
opened. An issue happens, for instance, when wpa_supplicant doesn't
have correct access permission to the directory specified by osu_dir.
If hs20_osu_fetch_done method returns without clearing the flag,
'FETCH_OSU' command will never work correctly.
Signed-off-by: Daichi Ueura <daichi.ueura@sonymobile.com>
When building P2P IE for Probe Request frames in P2P scan, add the
device information attribute if the 60 GHz band is included in the scan,
since this is required by the P2P specification.
Signed-off-by: Lior David <qca_liord@qca.qualcomm.com>
Expose the functions wpas_get_bands() and wpas_freq_to_band() and the
enum wpa_radio_work_band, since they will be needed outside
wpa_supplicant.c.
Signed-off-by: Lior David <qca_liord@qca.qualcomm.com>
When setting up parameters for P2P scan, calculate the frequencies
for the scan before calculating the scan IE. This is because
the scan IE calculation may need information about the scan
frequencies in use.
Signed-off-by: Lior David <qca_liord@qca.qualcomm.com>
Commit 02e122a995 ('Reschedule scan from
wpas_stop_pno if it was postponed') uses wpa_s->scanning as the only
condition for automatically starting a postponed scan request from
EVENT_SCHED_SCAN_STOPPED event handler. However, wpa_s->scanning may be
set for sched_scan and as such, this can result in unexpected extra
scans without there having been any real postponed request.
Make this more accurate by verifying that there really is a pending
request for a scan before speeding up its start.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Add support for drivers with dedicated P2P_DEVICE interface, but without
group interface concurrency (only a single netdev is used). With such
devices, wpa_supplicant tried to use the p2p_dev interface instead of
the group interface and most P2P operations failed. Extend
wpa_supplicant to use the primary interface instead of a separate group
interface in such cases.
Signed-off-by: Lior David <qca_liord@qca.qualcomm.com>
In many places in the code there was a reference to wpa_s->parent to get
from group interface to p2p_dev interface. These places can break if
P2P_DEVICE interface would need to be used with the primary interface as
the group interface, since the parent of the primary interface points to
itself and not the p2p_dev interface.
Fix this by adding a separate "p2pdev" pointer to wpa_supplicant,
it will be the same as parent pointer in most cases but whenever
the primary interface is used as a group interface, change it to
point to the correct p2p_dev interface.
Signed-off-by: Lior David <qca_liord@qca.qualcomm.com>
Use the SA field instead of BSSID in the received Action frame to
determine whether PMF has been negotiated with the transmitter. While
these fields are supposed to be same for Public Action frames from an
AP, it would be possible that a frame is received with different values.
The following operations in gas_query_rx() use SA, so do the same for
the PMF check.
Signed-off-by: Jouni Malinen <j@w1.fi>
If the BSS Transition Management Request frame includes only a single
candidate and we need to scan for the BSS to get up-to-date information,
use a scan for the known BSSID instead of wildcard BSSID. In addition,
set the SSID in the scan if it is known based on old scan results in the
BSS table. This removes unnecessary Probe Response frames when we are
interested in results from only a single BSS.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
If WPA2 is used, MBO AP must enable PMF. Refuse to select a BSS that has
MBO and WPA2 enabled without PMF.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This makes hostapd parse the MBO attribute in (Re)Association Request
frame and track the cellular data capability (mbo_cell_capa=<val> in STA
control interface command).
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This makes wpa_is_bss_tmp_disallowed() expire old entries from the
bss_tmp_disallowed list even if they do not match the BSSID that is
being searched for. This allows the list to be kept at shorter length to
speed up operations and minimize memory use in cases where the
previously disabled BSS is not in radio range anymore.
Signed-off-by: Jouni Malinen <j@w1.fi>
According to IEEE Std 802.11-2012, Table 8-22, vendor specific elements
must follow all other elements, so Hotspot 2.0 element which is actually
a vendor specific element must come after all other elements.
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
According to IEEE Std 802.11-2012, Table 8-22, RM Enabled Capabilities
element must come before the Extended Capabilities element.
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
Add an option to configure a candidate list to BSS transition query
("list" as the second argument to WNM_BSS_QUERY). The candidate list is
built from the available scan results. If no updated scan results (< 10
sec) are available, the command fails.
Signed-off-by: David Spinadel <david.spinadel@intel.com>
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
Add the transition candidate list to BSS Transition Management Response
frame. The candidates preference is set using the regular wpa_supplicant
BSS selection logic. If the BSS transition request is rejected and
updated scan results are not available, the list is not added.
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
When rejecting a BSS Transition Management Request frame, add MBO IE to
the BSS Transition Management Response frame to specify the transition
rejection reason.
Signed-off-by: David Spinadel <david.spinadel@intel.com>
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
Add parsing of MBO IE in BSS Transition Management Request frames. If
the MBO IE includes the association retry delay attribute, do not try to
reconnect to the current BSS until the delay time is over.
If the MBO IE includes the cellular data connection preference attribute
or the transition rejection reason attribute, send a message to upper
layers with the data.
Signed-off-by: David Spinadel <david.spinadel@intel.com>
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
Add definitions for global operating classes. These definitions will be
used to construct supported operating classes information element.
The operating classes definitions used locally for P2P module will be
removed and included in the general operating classes definitions.
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
Prevent association to MBO APs that have association disallowed
attribute in MBO IE in Beacon or Probe Response frames.
Signed-off-by: David Spinadel <david.spinadel@intel.com>
Add cellular capability attribute to MBO IE and add MBO IE with cellular
capabilities to Probe Request frames. By default, cellular capability
value is set to Not Cellular capable (3).
Signed-off-by: David Spinadel <david.spinadel@intel.com>
Send a WNM-Notification Request frame with Non-preferred Channel Report
subelement if the non-preferred channels list changes during an
association.
Signed-off-by: David Spinadel <david.spinadel@intel.com>
Add a helper function to find a certain IE inside IEs buffer by ID and
use this function in several places that implemented similar
functionality locally.
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
Remove the fallback dependency on os_random() when generating a WPS pin.
This is exceptionally unlikely to ever be called as the call to
os_get_random() is unlikely to fail. The intention is to facilitate
future removal of os_random() as it uses a low quality PRNG.
Signed-off-by: Nick Lowe <nick.lowe@lugatech.com>
The SAE PMKID is calculated with IEEE Std 802.11-2012 11.3.5.4, but the
PMKID was re-calculated with 11.6.1.3 and saved into PMKSA cache. Fix
this to save the PMKID calculated with 11.3.5.4 into the PMKSA cache.
Signed-off-by: Masashi Honma <masashi.honma@gmail.com>
Ensure that characters are represented as unsigned char when using
isblank() and isspace(). These function take in a "int c" argument, but
it needs to be unsigned for the cases where EOF is not indicated.
Signed-off-by: Roy Marples <roy@marples.name>
While '!func() == 0' here resulted in correct behavior, it is not clear
and clang is starting to warn about this (-Wlogical-not-parentheses).
Use 'func()' instead as the condition to clear this.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
PBSS (Personal Basic Service Set) is a new BSS type for DMG
networks. It is similar to infrastructure BSS, having an AP-like
entity called PCP (PBSS Control Point), but it has few differences.
PBSS support is mandatory for IEEE 802.11ad devices.
Add a new "pbss" argument to network block. The argument is used
in the following scenarios:
1. When network has mode=2 (AP), when pbss flag is set will start
as a PCP instead of an AP.
2. When network has mode=0 (station), when pbss flag is set will
connect to PCP instead of AP.
The function wpa_scan_res_match() was modified to match BSS according to
the pbss flag in the network block (wpa_ssid structure). When pbss flag
is set it will match only PCPs, and when it is clear it will match only
APs.
Signed-off-by: Lior David <qca_liord@qca.qualcomm.com>
NOTE: kqueue has to be closed and re-build after forking. epoll *should*
do the same, but it seems that wpa_supplicant doesn't need it at least.
I have re-worked a little bit of the epoll code (moved into a similar
kqueue function) so it's trivial to requeue epoll if needed in the
future.
Signed-off-by: Roy Marples <roy@marples.name>
This function can be used to re-build eloop socket tables after forking
for eloop implementations that need this.
Signed-off-by: Roy Marples <roy@marples.name>
It does more than intended; apart from denying messages to that
particular interface it also denies all messages non-qualified with an
interface globally. This blocks messages completely unrelated to
wpa_supplicant, such as NetworkManager communication with the VPN
plugins.
From the dbus-daemon manual:
Be careful with send_interface/receive_interface, because the
interface field in messages is optional. In particular, do NOT
specify <deny send_interface="org.foo.Bar"/>! This will cause
no-interface messages to be blocked for all services, which is almost
certainly not what you intended. Always use rules of the form: <deny
send_interface="org.foo.Bar" send_destination="org.foo.Service"/>
We can just safely remove those rules, since we're sufficiently
protected by the send_destination matches and method calls are
disallowed by default anyway.
Signed-off-by: Lubomir Rintel <lkundrak@v3.sk>
When a mesh point reconnects by starting from Authentication frame
sequence, the plink count was not decremented from its last connection.
This resulted in leaking peer link count and causing wpa_supplicant to
reject the connection after max_peer_links (default: 99) reconnects.
This was reproduced by pre-configuring 2 mesh points with mesh
credentials. Boot both mesh points and make sure they connect to each
other. Then in a loop reboot one of the mesh points after it
successfully connects while leaving the other mesh point up and running.
After 99 iterations the supplicant on mesh point that is not rebooting
will reject the connection request from the other mesh point.
Fix this by decrementing num_plinks when freeing a STA entry that is
still in PLINK_ESTAB state.
Signed-off-by: Srinivasa Duvvuri <sduvvuri@chromium.org>
In cases where the bandwidth is not set when starting an AP/P2P GO,
the code tries to use 160 MHz or 80 MHz channels. As a result, the
AP/P2P GO configuration is set to use these channel widths even if
they are not available, which may results in failing to start the
AP/P2P GO.
Fix this by changing the AP/P2P GO configuration not to use VHT channels
when they are not available. In this case the AP/P2P GO will use a 40
MHz channel, if available, or a 20 MHz channel, if this is the maximum
available width.
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
If the config file for the interface says "p2p_disabled=1", don't report
p2p capabilities on this interface. This helps programs like Connman to
not enable p2p when it's been disabled in wpa_supplicant.
Signed-off-by: John Ernberg <john.ernberg@actia.se>
Some APs do not advertise operating classes correctly for BSS Transition
Management. Try to determine the most likely operating frequency based
on the channel number (1..14 --> 2.4 GHz; 36..169 --> 5 GHz) if invalid
op_class == 0 is received in a BSS Transition Management Request. This
speeds up the following operating by avoiding a full scan due to an
unknown channel.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This patch keeps ip_addr* configuration in conf file while
updating supplicant conf file either internally by supplicant or
due to save_config command.
Signed-off-by: Purushottam Kushwaha <p.kushwaha@samsung.com>
Signed-off-by: Avichal Agarwal <avichal.a@samsung.com>
The maximum WPS Device Name length is 32 characters and that limit was
already enforced for the control interface and configuration files.
Signed-off-by: Purushottam Kushwaha <p.kushwaha@samsung.com>
This is needed to get proper P2P group removal processing for some test
cases. discovery_group_client followed by nfc_p2p_client was able to hit
a case where the P2P group idle timeout survived to the next group
instance because of the FLUSH command not clearing the group and this
timeout properly.
Signed-off-by: Jouni Malinen <j@w1.fi>
If the local driver indicated a peer candidate event when the peer had
already initiated peering exchange in open mesh case, we used to force a
new exchange to be started instead of allowing the previously started
exchange to complete. This is not desirable, so make this initiation of
the new exchange conditional on there not being an already started (or
successfully completed) exchange.
Signed-off-by: Jouni Malinen <j@w1.fi>
If the local driver event for a new peer candidate arrived only after
the peer had already initiated the peering exchange, we used to clear
the link state. This resulted in the already completed (or in progress)
exchange getting abandoned and a new exchange initiated. This is not
desirable since the already started (or even completed) exchange can be
used. Clear the link state only when adding the new STA entry for the
first time, i.e., use the same !sta->my_lid condition in handling the
driver event similarly to how the peer initiated cases were already
handled.
Signed-off-by: Jouni Malinen <j@w1.fi>
The messages were sent out with wpa_msg_ctrl() so they were not visible
in the debug log. However, these would be quite helpful strings to
search for in the debug log, so change these messages to use wpa_msg().
Signed-off-by: Jouni Malinen <j@w1.fi>
It was possible for the FLUSH command to trigger auto connect mechanism
to schedule a new scan in 100 ms. This is not desired since all the
network profiles will be removed immediately and the scan or an attempt
to reconnect would not be of any benefit here. Such a scan in 100 ms can
cause issues for cases where multiple test sequences are run back to
back, so prevent this by clearing wpa_supplicant state to DISCONNECTED
(which avoids scheduling of the 100 ms scan trigger on disconnection) if
the state was AUTHENTICATING or higher when the FLUSH command was
issued.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This adds notes on how wpa_supplicant can be configured for OSEN for a
link-layer protected online signup connection and how network profiles
can be set for a Hotspot 2.0 data connection when using external
Interworking network selection.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
The new wps_force_{auth,encr}_types parameters can be used in test build
(CONFIG_WPS_TESTING) to force wpa_supplicant to use the specified value
in the Authentication/Encryption Type flags attribute. This can be used
to test AP behavior on various error cases for which there are
workarounds to cover deployed device behavior.
Signed-off-by: Jouni Malinen <j@w1.fi>
Previously it was possible for the pending Action frame TX to be
cleared, but the offchannel TX operation being left in wait state in the
kernel. This would delay start of the next operation (e.g., that listen
operation requested by P2P_LISTEN) until the wait time for the
previously pending Action frame had expired.
Optimize this by explicitly stopping any pending offchannel Action frame
TX when clearing the internal offchannel TX state in
wpas_p2p_clear_pending_action_tx().
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
The new optional ssid=<hexdump> argument to P2P_CONNECT can be used to
make P2P Client operations during join-an-existing-group more robust by
filtering out scan results based on the SSID in addition to the P2P
Device/Interface Address. This can help if the same MAC address has been
used in multiple groups recently and the cached scan results may still
include an older BSS.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
At least one of the wpas_p2p_connect() callers (NFC join case) already
had access to the Group SSID. Pass that information through
wpas_p2p_connect() to wpas_p2p_join() so that the join operation can
filter out incorrect groups more easily.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Accept only a BSS entry matching the SSID when trying to find the
operating channel of a GO during join operation for which the SSID was
already specified. Previously, it could have been possible to pick an
incorrect BSS entry if the new GO was not found in the latest scan and
there was an older cached scan entry for the same BSSID.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
It was already possible to limit join operation to accept only a
specific SSID. However, this constraint was not used when starting a P2P
Client interface as a WPS Enrollee without going through a Provision
Discovery exchange.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Use wpa_bss_get() with the specific Group SSID instead of
wpa_bss_get_bssid_latest() if the SSID is already known. This makes the
P2P join operations more robust in case the frequency of the group was
not yet known and the same P2P Interface Address may have been used in
multiple group instances with an older group entry still present in the
cached scan results.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This allows the cases where a specific group SSID is known to filter out
groups on the P2P Client even if the specific BSS entry for the target
group is not yet available.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
The new optional group_ssid=<hexdump> argument in the P2PS-PROV-DONE
event can be used to help in identifying the exact group if there have
been multiple groups with the same P2P Interface Address in short period
of time.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Provide details on the pointers to the subfields and rename "pmk" to
"chosen_pmk" and use SAE_PMKID_LEN macro with it to make the code more
readable.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
From IEEE Std 802.11-2012 13.3.5:
If the incoming Mesh Peering Management frame is for AMPE and the
Chosen PMK from the received frame contains a PMKID that does not
identify a valid mesh PMKSA, the frame shall be silently discarded.
We were not checking the PMKID previously, and we also weren't parsing
it correctly, so fix both.
Signed-off-by: Bob Copeland <me@bobcopeland.com>
IEEE Std 802.11-2012 11.3.5.4 specifies the PMKID for SAE-derived keys
as:
L((commit-scalar + peer-commit-scalar) mod r, 0, 128)
This is already calculated in the SAE code when the PMK is derived, but
not saved anywhere. Later, when generating the PMKID for plink action
frames, the definition for PMKID from 11.6.1.3 is incorrectly used.
Correct this by saving the PMKID when the key is generated and use it
subsequently.
Signed-off-by: Bob Copeland <me@bobcopeland.com>
External programs are not aware of the creation of a
dedicated P2P Device interface, so it does not make sense
to wait for a monitor to connect on such an interface.
Fix this by not waiting on a dedicated P2P Device interface
for monitor to attach.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
In case an interface has started without a control interface
initialized, skip waiting for monitor to attach at the start of
wpa_supplicant (-W).
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
If LIBS is set with some global build system defaults, clone those for
LIBS_c, LIBS_h, LIBS_n, and LIBS_p to cover wpa_cli, wpa_passphrase,
hostapd_cli, hlr_auc_gw, and nt_password_hash as well.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Since hostapd supports ACS now, let's enable its support in
wpa_supplicant as well when starting AP mode.
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
[u.oelmann@pengutronix.de: rebased series from hostap_2_1~944 to master]
[u.oelmann@pengutronix.de: adjusted added text in defconfig]
Signed-off-by: Ulrich Ölmann <u.oelmann@pengutronix.de>
Let's reuse hostapd code for such handling. This will be useful to get
ACS support into wpa_supplicant where this one needs to handle the
survey event so it fills in the result ACS subsystem will require.
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
[u.oelmann@pengutronix.de: rebased series from hostap_2_1~944 to master]
Signed-off-by: Ulrich Ölmann <u.oelmann@pengutronix.de>
Commit f8a80e39b3 ('P2PS: Change
connection capability handling') added the identical P2PS_SETUP_CLIENT
check into two places within p2ps_group_capability(). However, only the
first one of these can be reached. In the second case, role can only
have values 0 or P2PS_SETUP_NEW and as such, the P2PS_SETUP_CLIENT case
is not possible. It looks like the first part of the commit is
sufficient, so remove the dead code added by the second part.
Signed-off-by: Jouni Malinen <j@w1.fi>
ocsp=3 extends ocsp=2 by require all not-trusted certificates in the
server certificate chain to receive a good OCSP status. This requires
support for ocsp_multi (RFC 6961). This commit is only adding the
configuration value, but all the currently included TLS library wrappers
are rejecting this as unsupported for now.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
The minimum comeback delay 1 is used to indicate that fragmentation is
needed instead of indicating that the response is going to be available
only after some time. Do not cancel offchannel wait for this case
between the initial and comeback exchanges to avoid delaying the full
operation unnecessarily.
Signed-off-by: Jouni Malinen <j@w1.fi>
It is possible for a comeback response to get lost especially when going
through a large GAS exchange fragmented to multiple frames in an
environment with interference or other traffic. Make this less likely to
fail the full exchange by trying full GAS query again and using longer
wait time on the GAS comeback exchanges.
Signed-off-by: Jouni Malinen <j@w1.fi>
When exchanging GAS frames with the AP, the initial response from the AP
may take a while to come, since the AP may need to fetch the info from a
server. The next fragments/comeback response frames should take much
less time since the AP already has all of the info, so the wait time
for these frames can be reduced.
In addition, some drivers, e.g., mac80211, try to combine ROC based flows,
to improve medium utilization. For example, if the requested ROC fits
entirely in a previous requested ROC they can be combined. Thus, reducing
the wait time for the next frames can improve medium utilization.
Shorten the duration of GAS comeback to improve medium utilization and
overall GAS exchange times.
Signed-off-by: Matti Gottlieb <matti.gottlieb@intel.com>
Commit 2c0d0ae370 ('GAS: End
remain-on-channel due to delayed GAS comeback request') started ending
the remain-on-channel operation between the initial request and the
following comeback request. However, it did not check or update the
offchannel_tx_started variable. While this alone would not necessarily
be problematic, this makes it more difficult to optimize wait time for
offchannel TX operations, so make sure the internal tracking variable
gets updated.
Signed-off-by: Jouni Malinen <j@w1.fi>
Such a pending frame cannot be valid anymore, so drop it instead of
risking of using an unexpected EAPOL frame after association if a
previous association received one at the end and the new association can
happen within 100 ms.
Signed-off-by: Jouni Malinen <j@w1.fi>
Only one of the icon entries with a matching BSSID and file name can be
fetched from wpa_supplicant and as such, there is no need to maintain
the old data if it was not explicitly deleted before running a new fetch
for the same BSSID and icon. Remove older duplicated entries whenever
completing a pending icon fetch to optimize memory use.
Signed-off-by: Jouni Malinen <j@w1.fi>
This adds a new command based Hotspot 2.0 icon retrieval option.
In short, here is the new command sequence:
1. REQ_HS20_ICON <bssid> <file-name>
2. event: RX-HS20-ICON <bssid> <file-name> <size>
3. GET_HS20_ICON <bssid> <file-name> <offset> <size>
(if needed, repeat with larger offset values until full icon is
fetched)
5. DEL_HS20_ICON <bssid> <file-name>
REQ_HS20_ICON is a new command that is analogous to HS20_ICON_REQUEST
with the slight difference that an entry to store the icon in memory is
prepared. The RX-HS20-ICON event has been augmented with BSSID,
file-name and size, and GET_HS20_ICON is used to retrieve a chunk of up
to <size> bytes of icon data at offset <offset>. Each chunk is returned
as a base64 encoded fragment, preceded by "HS20-ICON-DATA", BSSID, and
file-name as well as the starting offset of the data.
If there is no entry prepared for the icon when the ANQP result comes
back, hs20_process_icon_binary_file falls back to legacy behavior.
Finally the DEL_HS20_ICON command deletes (all) icons associated with
BSSID and file-name (there could be several if retries are used and they
have different dialog tokens).
Signed-off-by: Jan Nordqvist <jannq@google.com>
SIGNAL_MONITOR THRESHOLD=DD HYSTERESIS=DD command will request signal
strength monitoring events based on there having been requested amount
of drop in the signal strength. The threshold value is the RSSI
threshold in dBm for the event to be sent. 0 threshold can be used to
disable monitoring. The hysteresis value is RSSI hysteresis in dB to
specify the minimum amount of change before a consecutive event is
reported.
With nl80211 driver interface, these values map to the
NL80211_CMD_SET_CQM command with NL80211_ATTR_CQM_RSSI_THOLD and
NL80211_ATTR_CQM_RSSI_HYST attributes to the driver.
This command cannot be used when bgscan module is in use since that
depends on being able to control the connection monitoring parameters.
Signed-off-by: Dmitry Shmidt <dimitrysh@google.com>
During the sequence of exchanging GAS frames with the AP, the AP can
request to come back in X amount of time and resend the GAS request.
Previously, wpa_supplicant did not terminate the remain-on-channel
session, but rather waited until the requested comeback delay had
expired, and then tried to send the GAS frame (potentially to save the
time that is required to schedule a new remain on channel flow).
This might cause unnecessary idle time (can be close to 1000 ms) in
which the device might be off-channel. Ending the current
remain-on-channel session and then rescheduling makes better usage of
the time in this case.
End remain-on-channel session due to receiving a delayed GAS comeback
request from the AP.
Signed-off-by: Matti Gottlieb <matti.gottlieb@intel.com>
wpa_ctrl_command_sta(), called by the "ALL_STA" handler, didn't consider
ifname_prefix, resulting in various commands being sent to the global
control interface, rather than the specified interface when IFNAME=
prefix was used.
This in turn caused the unexpected "UNKNOWN COMMAND" result be
considered as valid station, resulting in infinite loop while trying to
get all stations.
Fix it by considering ifname_prefix, similarly to _wpa_ctrl_command().
Signed-off-by: Eliad Peller <eliadx.peller@intel.com>
Previously, when wpa_supplicant received bgscan results with a preferred
network, it connected to that network without disconnecting from the
previous one. This might result in an inconsistent state of upper
layers.
Fix this by disconnecting from the current AP before connecting to the
new one when the network profile changes and there is an existing
connection.
Signed-off-by: Ayala Beker <ayala.beker@intel.com>
If scan results arrive during the connection process, the network
selection function was called, interrupting the current connection.
While a regular scan is mutually exclusive with connection establishment
via the nature of radio work, there's no such protection for scheduled
scan. Prevent network selection while a connection is in progress.
Signed-off-by: Arik Nemtsov <arikx.nemtsov@intel.com>
Fix wpas_p2p_invite() to call p2p_set_own_pref_freq_list() after the
NULL check, to avoid NULL pointer dereference if P2P initialization were
to have failed or P2P module getting deinitialized.
Signed-off-by: Ayala Beker <ayala.beker@intel.com>
The full VHT channel information was not set in the hostapd data
structures which resulted in incorrect information (all zeros) being
used when building the VHT Operation element for peering messages while
the actual driver mode was set with the full details. We did not seem to
use the VHT information from peering messages, so this does not change
behavior with another wpa_supplicant-based mesh implementation. Anyway,
these elements should match the ones used in Beacon frames.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This allows the internal TLS client implementation to accept
CertificateStatus message from the server when trying to use OCSP
stapling. The actual OCSPResponse is not yet processed in this commit,
but the CertificateStatus message is accepted to allow the TLS handshake
to continue.
Signed-off-by: Jouni Malinen <j@w1.fi>
This adds support for optional functionality to validate server
certificate chain in TLS-based EAP methods in an external program.
wpa_supplicant control interface is used to indicate when such
validation is needed and what the result of the external validation is.
This external validation can extend or replace the internal validation.
When ca_cert or ca_path parameter is set, the internal validation is
used. If these parameters are omitted, only the external validation is
used. It needs to be understood that leaving those parameters out will
disable most of the validation steps done with the TLS library and that
configuration is not really recommend.
By default, the external validation is not used. It can be enabled by
addingtls_ext_cert_check=1 into the network profile phase1 parameter.
When enabled, external validation is required through the CTRL-REQ/RSP
mechanism similarly to other EAP authentication parameters through the
control interface.
The request to perform external validation is indicated by the following
event:
CTRL-REQ-EXT_CERT_CHECK-<id>:External server certificate validation needed for SSID <ssid>
Before that event, the server certificate chain is provided with the
CTRL-EVENT-EAP-PEER-CERT events that include the cert=<hexdump>
parameter. depth=# indicates which certificate is in question (0 for the
server certificate, 1 for its issues, and so on).
The result of the external validation is provided with the following
command:
CTRL-RSP-EXT_CERT_CHECK-<id>:<good|bad>
It should be noted that this is currently enabled only for OpenSSL (and
BoringSSL/LibreSSL). Due to the constraints in the library API, the
validation result from external processing cannot be reported cleanly
with TLS alert. In other words, if the external validation reject the
server certificate chain, the pending TLS handshake is terminated
without sending more messages to the server.
Signed-off-by: Jouni Malinen <j@w1.fi>
The new wpa_supplicant control interface command "TEST_ASSOC_IE
<hexdump>" can now be used to override the WPA/RSN IE for Association
Request frame and following 4-way handshake to allow protocol testing of
AP side processing of WPA/RSN IE.
Signed-off-by: Jouni Malinen <j@w1.fi>
The new methods are
1. VendorElemAdd "i" "ay" i=integer ay=array of bytes
2. VendorElemGet "i" i=integer (output array of bytes)
3. VendorElemRem "i" "ay" i=integer ay=array of bytes
These provide functionality similar to the control interface commands
VENDOR_ELEM_ADD, VENDOR_ELEM_GET, and VENDOR_ELEM_REMOVE.
Signed-off-by: Avichal Agarwal <avichal.a@samsung.com>
Signed-off-by: Purushottam Kushwaha <p.kushwaha@samsung.com>
Signed-off-by: Kyeong-Chae Lim <kcya.lim@samsung.com>
Signed-off-by: Mayank Haarit <mayank.h@samsung.com>
Signed-off-by: Dilshad Ahmad <dilshad.a@samsung.com>
[VendorElemGet to return array of bytes instead of string; cleanup]
Signed-off-by: Jouni Malinen <j@w1.fi>
This was already working for the case where a separate group interface
is used due to the recent commit
328f49acfe ('P2P: Complete group formation
on client data connection'). However, the case of no separate group
interface was used did not clear the interface state properly on data
connection. Fix this by setting the group formation information in
wpas_start_p2p_client().
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Commit f05cee9714 ('P2P: Clear
p2p_in_invitation on cancel') added a wpas_p2p_cancel() case to call
wpas_p2p_group_formation_failed() if wpa_s->p2p_in_invitation is set.
This is done in a loop going through wpa_s->next pointers. However, the
call here can result in removing the interface and freeing wpa_s. The
following attempt to read wpa_s->next is from freed memory and that can
result in process termination when using a separate P2P group interface
and issuing P2P_CANCEL on a group that was started through re-invocation
of a persistent group.
The recent commit 328f49acfe ('P2P:
Complete group formation on client data connection') "fixed" this by
accident since wpa_s->p2p_in_invitation gets cleared in the sequence
that could hit this issue and this results in P2P_CANCEL getting
rejected. However, the real bug here is in the loop that continues after
possible wpa_s instance deletion. Fix that by breaking out of the loop.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This makes it easier to share the OCSP implementation needed for
BoringSSL outside tls_openssl.c. For now, this is mainly for
http_curl.c.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This was already the case in the GO role where the first client
connection is waited before marking
wpa_s->p2p_go_group_formation_completed = 1 and clearing
wpa_s->global->p2p_group_formation. However, in the P2P Client role,
that was done already at the completion of the WPS exchange. This can be
problematic since group formation timeout may still try to clear the
group and with wpa_s->global->p2p_group_formation == NULL, the correct
group interface may not be found.
Fix this by postponing clearing of wpa_s->global->p2p_group_formation on
the P2P Client side until the data connection has been completed and
group is declared started.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This allows the control interface SET command to be used to update the
sched_scan_plans parameter at runtime. In addition, an empty string can
be used to clear the previously configured plan.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Add the option to configure scheduled scan plans in the config file.
Each scan plan specifies the interval between scans and the number
of scan iterations. The last plan will run infinitely and thus
specifies only the interval between scan iterations.
usage:
sched_scan_plans=<interval:iterations> <interval2:iterations2> ... <interval>
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
Add 'scan plans' to driver scan parameters for scheduled scan.
Each 'scan plan' specifies the number of iterations to run the scan
request and the interval between iterations. When a scan plan
finishes (i.e., it was run for the specified number of iterations),
the next scan plan is executed. The last scan plan will run
infinitely.
The maximum number of supported scan plans, the maximum number of
iterations for a single scan plan and the maximum scan interval
are advertised by the driver.
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
A hwsim test sequence was able to hit a SIGSEGV in
p2p_go_save_group_common_freqs() called by p2p_go_configured() callback
in a case where a non-P2P AP mode operation is started in wpa_supplicant
(wpas_ap_wep test case). This callback should not have happened for
non-P2P case and the debug logs did not make it clear how this could
happen. In addition, it is unclear how this could be reproduced.
To avoid this type of issues, clear the wpa_s->ap_configured_cb pointer
as soon as the first call to the function happens. In addition, verify
that wpa_s->go_params is available before processing the GO configured
callback.
Signed-off-by: Jouni Malinen <j@w1.fi>
These will be used with the internal TLS implementation to extend hash
algorithm support for new certificates and TLS v1.2.
Signed-off-by: Pali Rohár <pali.rohar@gmail.com>
This may speed up some hwsim test case sequencies by avoiding a wait for
a scan at the end of a test case to complete.
Signed-off-by: Jouni Malinen <j@w1.fi>
Connect radio work is sometimes delayed for a considerable duration if
there is an ongoing scan radio work. To avoid these delays abort the
ongoing scan on that interface before queuing a connect request. Upon a
scan done indication from the driver, connect radio work will be
scheduled.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This adds the driver interface commands for issuing a request to abort
an ongoing scan operation.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This is needed to avoid hitting WEP/TKIP detection in
ibss_mesh_setup_freq() if the previous connection used WEP or TKIP.
Previously, that could have resulted in VHT and HT getting disabled for
the mesh connection.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
A new network profile configuration parameter max_oper_chwidth=3 can be
used to specify preference to enable 80+80 MHz VHT channel for IBSS. If
that is set, the first 80 MHz segment is specified based on the
frequency parameter in the network profile and the second segment is
selected automatically (which will practically be limited to a single
possibility due to DFS requirements in most countries).
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
The new max_oper_chwidth and freq2 arguments to P2P_CONNECT, P2P_INVITE,
and P2P_GROUP_ADD control interface commands can be used to request
larger VHT operating channel bandwidth to be used than the previously
used maximum 80 MHz.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This extends the previous design that covered only the VHT 80 MHz cases
for VHT channel flags. New functions are introduced to allow 160 MHz
bandwidth cases to determine the center channel and check availability
of a 160 MHz channel.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This adds definitions for the global operating classes 129 and 130 for
VHT 80+80 MHz and 160 MHz use cases.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Previously, MB IEs were parsed only from association event. Try to get
MB IEs from other management frames like Probe Response frames. The MB
IEs from the association event may not be up-to-date and in some cases
may actually be missing and updating the information based on other
frames can improve robustness of FST exchanges.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
There was only a single file remaining in this directory. All the other
old test functionality has been moved under the top level tests
directory. Move the remaining file to the wpa_supplicant directory to
get rid of the subdirectory.
Signed-off-by: Jouni Malinen <j@w1.fi>
The old wpa_supplicant/Makefile target test-eap_sim_common did not work
anymore and anyway, this test is better placed in the newer hwsim
framework to make sure the test case gets executed automatically.
Signed-off-by: Jouni Malinen <j@w1.fi>
These wpa_supplicant test programs have not been maintained for years
and it would take significant effort to get these into working state.
Since there does not seem to be any real need for these based on lack of
maintenance, it is easier to just drop these tools for now.
Signed-off-by: Jouni Malinen <j@w1.fi>
Number of places were calling functions that are not included in
CONFIG_NO_WPA=y build anymore. Comment out such calls. In addition, pull
in SHA1 and MD5 for config_internal.c, if needed.
Signed-off-by: Jouni Malinen <j@w1.fi>
When an invitation to join an existing group is accepted by the
peer device, set p2p_go_wait_client to the current time so
that wpas_p2p_in_progress() would return != 0, thus preventing
P2P CSA, scanning etc., that would interfere with the peer
device connection.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Some drivers do not support having two station interfaces, so the fact
that wpa_supplicant always creates a new interface in station mode, even
if it will be used as another type of interface, may prevent
wpa_supplicant from creating new interfaces. Allow setting the interface
type when a new interface is created so that interfaces of supported
types can be created.
Currently supported types are station ("sta") and AP ("ap"). If the
interface type is not specified, a station interface will be created.
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
When an AP interface it created, it is also setup and subscribes
for management frames etc. However, when the interface is added by
wpa_supplicant, setting up for AP operations is redundant because
it will be done by wpa_supplicant on wpa_drv_init() when setting
the interface mode to AP.
In addition, it may cause wpa_supplicant to fail initializing the
interface as it will try to subscribe for management frames on this
interface but the interface is already registered.
Change this, so when adding an AP interface, make setting up the AP
optional, and use it only when the interface is added by hostapd but not
when it is added by wpa_supplicant.
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
When clearing pending TX action to start a new P2P operation like
P2P_FIND or P2P_LISTEN, wpas_p2p_action_tx_clear() was used to clear
the send action work. However, in cases where the action work has wait
time, it is not cleared immediately but only after the wait time ends.
This may cause delay in starting the P2P operation.
Fix that by always clearing the send action work immediately on these
P2P commands that result in immediate P2P state change and practically
stopping a previous operation, if one was pending.
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
This allows offloaded roaming to inform user space of the change in IP
subnet post roaming. The device may have roamed to a network which is in
a different subnet which will result in IP connectivity loss. Indicating
the change in subnet enables the user space to refresh the IP address or
to perform IP subnet validation if unknown status is indicated.
The driver indication is reported with a new event from wpa_supplicant
in the following format:
CTRL-EVENT-SUBNET-STATUS-UPDATE status=<0/1/2>
where
0 = unknown
1 = IP subnet unchanged (can continue to use the old IP address)
2 = IP subnet changed (need to get a new IP address)
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Commit 2a6f78fbbe ('Do not re-associate on
SELECT_NETWORK to current network') started skipping all SELECT_NETWORK
connection steps if the selected network had already been selected
previously. This happened regardless of whether the connection was
already established. This is not necessarily desirable for all cases
where there is no immediate action to even try to connect (e.g., long
wait for the next scan).
Speed this up by allowing the SELECT_NETWORK operation to get started if
there is no connection or ongoing connection attempt with the selected
network.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Mesh Points themselves have capability to support VHT as long as
hardware supports it. However, supporting VHT in mesh mode was disabled
because no one had clearly tested and confirmed its functionality. Since
VHT80 has now been verified to work with ath10k QCA988X driver and
mac80211_hwsim, enable VHT support in mesh mode.
Signed-off-by: Peter Oh <poh@qca.qualcomm.com>
Set WLAN_STA_WMM flag to Mesh STA by default since Mesh STAs are QoS
STAs. Mesh STA's HT capabilities won't be parsed properly without the
flag.
Signed-off-by: Peter Oh <poh@qca.qualcomm.com>
If "STA_AUTOCONNECT 0" has been used to disable automatic connection on
disconnection event and the driver indicates a failure for the data
connection after successful WPS handshake, it is possible to hit a case
where wpa_s->disconnected is set to 1 and further attempts to connect
shall stop.
While "STA_AUTOCONNECT 0" is used to disable automatic reconnection
attempts in general, this specific WPS case can benefit from trying
again even with that configuration for a short period of time. Extend
the wpa_supplicant re-enable-networks-after-WPS 10 second timeout to
apply for ignoring disabled STA_AUTOCONNECT immediately after a WPS
provisioning step.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Free the message after message send in
wpas_dbus_signal_p2p_invitation_received() to avoid leaking memory.
Signed-off-by: Mayank Haarit <mayank.h@samsung.com>
Signed-off-by: Avichal Agarwal <avichal.a@samsung.com>
The upstream wpa_supplicant uses the dbus-1 library when it is compiled
with D-Bus support. In Android, we imported the D-Bus shared libraries
under the name "libdbus", so use this shared library instead of dbus-1
when compiling wpa_supplicant with D-Bus support.
Signed-off-by: Samuel Tan <samueltan@google.com>
This is similar to SAVE_CONFIG on control interface, which allow users
to update the configuration file.
Signed-off-by: Purushottam Kushwaha <p.kushwaha@samsung.com>
Signed-off-by: Mayank Haarit <mayank.h@samsung.com>
The AP is not expected to send out a WNM-Sleep Mode Response frame
without the STA trying to use WNM-Sleep Mode. Drop such unexpected
responses to reduce unnecessary processing of the frame.
Signed-off-by: Jouni Malinen <j@w1.fi>
WNM Sleep Mode Response frame is used to update GTK/IGTK only if PMF is
enabled. Verify that PMF is in use before using this field on station
side to avoid accepting unauthenticated key updates. (CVE-2015-5310)
Signed-off-by: Jouni Malinen <j@w1.fi>
Some APs may send RSC octets in EAPOL-Key message 3 of 4-Way Handshake
or in EAPOL-Key message 1 of Group Key Handshake in the opposite byte
order (or by some other corrupted way). Thus, after a successful
EAPOL-Key exchange the TSC values of received multicast packets, such as
DHCP, don't match the RSC one and as a result these packets are dropped
on replay attack TSC verification. An example of such AP is Sapido
RB-1732.
Work around this by setting RSC octets to 0 on GTK installation if the
AP RSC value is identified as a potentially having the byte order issue.
This may open a short window during which older (but valid)
group-addressed frames could be replayed. However, the local receive
counter will be updated on the first received group-addressed frame and
the workaround is enabled only if the common invalid cases are detected,
so this workaround is acceptable as not decreasing security
significantly. The wpa_rsc_relaxation global configuration property
allows the GTK RSC workaround to be disabled if it's not needed.
Signed-off-by: Max Stepanov <Max.Stepanov@intel.com>
The SCAN TYPE=ONLY results do not trigger a connection operation
automatically. As such, there was no explicit operation that would
change wpa_state after such a scan-only operation and WPA_SCANNING state
could have been left in effect until the next operation is triggered by
an external command. This is not desirable, so restore the wpa_state
that was in use when the scan was started in case WPA_SCANNING state is
still set when the scan operation completes.
This was triggered by the following mac80211_hwsim test sequence:
dbus_wps_oom scan_trigger_failure
Signed-off-by: Jouni Malinen <j@w1.fi>
Previously, wnm_deallocate_memory() was called only if we decided to
move to another BSS at the completion of an accepted BSS Transition
Management Request. This resulted in the candidate information being
left in effect for the following scan operation if we were already
associated with the preferred candidate. This could result in unexpected
behavior in the following connection attempt.
Fix this by clearing the candidate information even if we do not need to
roam to another BSS.
This was triggered with mac80211_hwsim test cases in this sequence:
wnm_bss_tm ap_track_sta_force_2ghz
Signed-off-by: Jouni Malinen <j@w1.fi>
libwpa_test1 and libwpa_test2 targets can now be used to check
libwpa_client linking for static and shared library cases respectively.
Signed-off-by: Jouni Malinen <j@w1.fi>
Building libwpa_client requires src/utils/common.c for bin_clear_free()
else loading the library fails with:
Error relocating /usr/lib/libwpa_client.so: bin_clear_free: symbol not found
Signed-off-by: Jörg Krause <joerg.krause@embedded.rocks>
All interface globals are now exposed as D-Bus properties of type
string, and parsed via the normal interface global parsing functions.
Signed-off-by: Dan Williams <dcbw@redhat.com>
hmac_sha256_kdf() got pulled in only if CONFIG_ERP=y is set. Fix
test_sha256() by making the test case conditional on the function being
present.
Signed-off-by: Jouni Malinen <j@w1.fi>
This is useful for logrotate to be able to rotate the file even if the
control interface is not enabled (e.g., when using DBus).
Signed-off-by: Lubomir Rintel <lkundrak@v3.sk>
Linux packet socket workaround(*) has an impact in performance when the
workaround socket needs to be kept open to receive EAPOL frames. While
this is normally avoided with a kernel that has the issue addressed by
closing the workaround packet socket when detecting a frame through the
main socket, it is possible for that mechanism to not be sufficient,
e.g., when an open network connection (no EAPOL frames) is used.
Add a build option (CONFIG_NO_LINUX_PACKET_SOCKET_WAR=y) to disable the
workaround. This build option is disabled by default and can be enabled
explicitly on distributions which have an older kernel or a fix for the
kernel regression.
Also remove the unused variable num_rx.
(*) Linux kernel commit 576eb62598f10c8c7fd75703fe89010cdcfff596
('bridge: respect RFC2863 operational state') from 2012 introduced a
regression for using wpa_supplicant with EAPOL frames and a station
interface in a bridge.
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qti.qualcomm.com>
Instead of trying to associate in configuration that is known to result
in the AP rejecting the association, reject the BSS candidate based on
the MFPR=1 RSN capability when STA configuration has PMF disabled.
Signed-off-by: Jouni Malinen <j@w1.fi>
This element is required to have at least four octets of actual payload.
This was not previously verified before use and the extra buffer data
after the IE might have been used instead if a received WNM-Sleep Mode
Response frame was invalid.
Signed-off-by: Jouni Malinen <j@w1.fi>
This moves the type cast needed for the current driver interface to
ieee802_11_set_tfs_ie() to allow the WNM-Sleep parsing routines to use
const pointers.
Signed-off-by: Jouni Malinen <j@w1.fi>
Reorder terms in a way that no invalid pointers are generated with
pos+len operations. end-pos is always defined (with a valid pos pointer)
while pos+len could end up pointing beyond the end pointer which would
be undefined behavior.
Signed-off-by: Jouni Malinen <j@w1.fi>
Reorder terms in a way that no invalid pointers are generated with
pos+len operations. end-pos is always defined (with a valid pos pointer)
while pos+len could end up pointing beyond the end pointer which would
be undefined behavior.
Signed-off-by: Jouni Malinen <j@w1.fi>
Reorder terms in a way that no invalid pointers are generated with
pos+len operations. end-pos is always defined (with a valid pos pointer)
while pos+len could end up pointing beyond the end pointer which would
be undefined behavior.
Signed-off-by: Jouni Malinen <j@w1.fi>
Reorder terms in a way that no invalid pointers are generated with
pos+len operations. end-pos is always defined (with a valid pos pointer)
while pos+len could end up pointing beyond the end pointer which would
be undefined behavior.
Signed-off-by: Jouni Malinen <j@w1.fi>
Reorder terms in a way that no invalid pointers are generated with
pos+len operations. end-pos is always defined (with a valid pos pointer)
while pos+len could end up pointing beyond the end pointer which would
be undefined behavior.
Signed-off-by: Jouni Malinen <j@w1.fi>
Reorder terms in a way that no invalid pointers are generated with
pos+len operations. end-pos is always defined (with a valid pos pointer)
while pos+len could end up pointing beyond the end pointer which would
be undefined behavior.
Signed-off-by: Jouni Malinen <j@w1.fi>
If hostapd or wpa_supplicant is built from a git repository, add a
VERSION_STR postfix from the current git branch state. This is from "git
describe --dirty=+". VERSION_STR will thus look something like
"2.6-devel-hostap_2_5-132-g4363c0d+" for development builds from a
modified repository.
This behavior is enabled automatically if a build within git repository
is detected (based on ../.git existing). This can be disabled with
CONFIG_NO_GITVER=y in wpa_supplicant/.config and hostapd/.config.
Signed-off-by: Jouni Malinen <j@w1.fi>
Vendor specific IEs added to frame type P2P_ASSOC_RESP are saved in
the interface context, but as they are added as part of the P2P IEs,
they need to be saved in the global P2P context.
Fix this by directing vendor specific IEs added to P2P_ASSOC_RESP
frame type to the P2P context.
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
This makes it easier to analyze debug logs for issues related to
multiple pending Action TX frames.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Do not expire scan results entries based on scan results from a scan
that was aborted. The aborted scan did not scan all the requested
channels or SSIDs, so the fact that a BSS is missing from the scan
results does not mean it is not available.
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
CTWindow was set for all AP interfaces if the driver supports it and
this parameter is set in wpa_supplicant configuration. This results in
failing to start an AP that is not a P2P GO as this setting is rejected
by the driver.
Fix that by setting the CTWindow only for P2P GO interface.
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
Add a global D-Bus handler ExpectDisconnect for setting
wpa_s->own_disconnect_req flag. This flag will prevent wpa_supplicant
from adding blacklists and requesting incomplete scan upon the incoming
disconnection. This is mainly meant for a case where suspend/resume is
used and some external component knows about that and can provide the
information to wpa_supplicant before the disconnection happens.
Signed-off-by: Ningyuan Wang <nywang@google.com>
It was possible for wpa_s->own_disconnect_req to be left set to 1 from a
disconnection attempt from a prior connection. This could then prevent
proper connection failure processing with the new connection in
wpas_connection_failed(). This was triggered by the following hwsim test
case sequence: wpas_mesh_secure sae_no_ffc_by_default. In this sequence,
the SAE failure due to unsupported group did not result in proper
wpas_connection_failed() processing and retry.
Fix this by clearing wpa_s->own_disconnect_req in
wpa_supplicant_associate() before starting a new connection.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
When one peer doesn't include a persistent group info in PD Request
the other peer shouldn't report a persistent group usage with this
peer even if such a persistent group exists locally. This condition
could be violated in the previous implementation.
In case a local persistent group exists and the
wpas_p2ps_prov_complete() function is called with persist_ssid parameter
set to NULL, wpa_supplicant reported P2PS-PROV-DONE with persist=<idx>
instead of conncap=<role> parameter.
This happened because the wpas_p2p_get_persistent() function was called
without verification whether the persist_ssid was set to NULL. In this
case the wpas_p2p_get_persistent() returns the first existing persistent
group matching the P2P Device Address without verifying the group's
SSID. After that the group ID is used as persist=<idx> parameter of
P2PS-PROV-DONE event.
Fix the issue by adding persist_ssid and persist_ssid_size verification
as a condition for the wpas_p2p_get_persistent() call.
Signed-off-by: Max Stepanov <Max.Stepanov@intel.com>
On successful P2P PD, report the chosen frequency in case the local
device is going to be the P2P GO, so in can later be used to instantiate
the new P2P GO, etc.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Add operating channel selection and channel list processing similar to
that done when building GO Negotiation Request, i.e., consider the
currently used channels, configured channels, etc.
P2PS introduces a flow where a responder needs to provide channel data
without being previously aware of the current constraints, i.e., the
channels currently in use by other interfaces. To handle this, extend
the get_group_capability() callback to also handle channel selection
aspects of group capabilities.
In case there is an active P2P GO that is going to be used for the P2PS
PD, force its current operating frequency in the PD attributes.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Change the connection capability handling so that in case there are no
active roles, the peer has an active GO, and the advertisement supports
operation as a client, the returned connection capability is set to
client.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
The code was iterating all the interfaces, and for each interface
iterated all the network blocks to count active P2P GO and P2P Client
interfaces.
Change the code to reuse wpas_p2p_get_go_group() to get a P2P GO
interface and add wpas_p2p_get_cli_group() and use it to find a
P2P Client interface, and use these objects when evaluating the
group capability.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Re-factor wpas_p2p_get_go_group() to:
1. Skip the dedicated P2P Device management interface if it is used.
2. Instead of iterating all the interface configured networks,
only access the current_ssid pointer to check if the current
interface is acting as a persistent P2P GO.
To avoid code duplication, also re-factor wpas_p2p_group_go_ssid()
to call wpas_p2p_get_go_group().
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
This allows wpa_supplicant to expose internally unknown ANQP-elements in
the BSS command. For example, "ANQP_GET <BSSID> 265" can be used to
fetch the AP Geospatial Location ANQP-element and if the AP has this
information, the "BSS <BSSID>" command will include the response as
"anqp[265]=<hexdump>".
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
The switch to BoringSSL broke keystore-backed keys because
wpa_supplicant was using the dynamic ENGINE loading to load
the keystore module.
The ENGINE-like functionality in BoringSSL is much simpler
and this change should enable it.
Signed-off-by: Dmitry Shmidt <dimitrysh@google.com>
IEEE Std 802.11-2012 13.3.1 states that the AID should be generated on
the local node for each peer. Previously, we were using the peer link ID
(generated by the peer) which may not be unique among all peers. Correct
this by reusing the AP AID generation code.
Signed-off-by: Bob Copeland <me@bobcopeland.com>
dl_list_del() must be called before freeing the list entries. Neither of
these cases caused problems because the full list data structure was
freed, but still, it is better to do this properly.
Signed-off-by: Jouni Malinen <j@w1.fi>
Some operations like a new scan result processing can result in large
number of wpa_supplicant control interface messages being generated.
Especially with multiple control interface monitors, this could result
in hitting the output queue length maximum and event messages getting
dropped. In worst case, that could even result in hitting ten
consecutive sendto() errors which could result in an attached monitor
socket getting detached.
Avoid this type of issues by throttling monitor event transmission based
on the output queue length. If more than half of the maximum send buffer
is used, postpone sending of following event messages until the pending
output queue has dropped below the limit.
Signed-off-by: Jouni Malinen <j@w1.fi>
The CSA channel and operating class values need to be set for all types
of channel switch (i.e., either if it's triggered by the control
interfaces or due to the GO-follows-STA flow). To do so, move the code
that sets them from the GO-follows-STA flow to the more generic
hostapd_fill_csa_settings() function.
Signed-off-by: Luciano Coelho <luciano.coelho@intel.com>
Some management frames contain CSA counters which should be updated by
kernel. Change driver op send_mlme() allowing to send a frame,
specifying an array of offsets to the CSA counters which should be
updated. For example, CSA offsets parameters should be specified when
sending Probe Response frames during CSA period.
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
Channel switch notification was handled only for AP/GO interfaces. As
the notification can be sent on other interface types as well, extend
the handling to handle other interface types.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Add new GO frequency move policy. The P2P_GO_FREQ_MOVE_SCM_ECSA prefers
SCM if all the clients advertise eCSA support and the candidate
frequency is one of the group common frequencies.
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
Do not consider moving GOs to a new channel if one of them is in the
middle of CSA. In addition, call wpas_p2p_update_channel_list() after
EVENT_CH_SWITCH is handled.
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
wpas_p2p_move_go_csa() uses wpas_p2p_init_p2p_params() to select the
frequency to move to. However, it is possible that all the channels are
already used, so the selection of a new frequency would fail, although
the frequency used by the P2P GO should not be considered as used if it
is the only one using it.
To overcome this, allow the frequency selection to continue even if all
the frequencies are in use, but the frequency used by the P2P GO is not
used by any station interface.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Use channel switch mechanism to move a P2P GO to a new channel,
when required. In order to be able to reconfigure the GO channel,
split wpa_supplicant_conf_ap() function, so the frequency
configuration part can be reused to find additional CSA settings.
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
The readline library depends on ncurses, so it should be set before
ncurses on the linker command line to be able to be statically linked
successfully.
Signed-off-by: David du Colombier <0intro@gmail.com>
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
This allows the binary sizes to be reduced if no support for nl80211
vendor extensions are needed.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This commit contains the necessary changes to parallelize
distinct radio work operations which are different in type and
the band used, only when the underlying driver is capable of
supporting such simultaneous offchannel operations.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Allow wpa_supplicant to use vendor scan (if supported by the driver)
together with the normal nl80211 scan and handling external scan events.
Since this results in possibility of concurrent scan operations, some of
the operations related to scan results need to check more carefully when
an event is relevant for a specific interface.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This is equivalent to the P2P_EVENT_INVITATION_RECEIVED signal on the
control interface. It can be used to sent the Invitation Received signal
to applications written using D-Bus.
Signed-off-by: Maneesh Jain <maneesh.jain@samsung.com>
Fix a bug in wpas_ap_ch_switch() function, which didn't pass VHT
frequencies correctly to hostapd_event_ch_switch().
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
Fix an iteration bug in get_shared_radio_freqs_data when building
freqs_data array. Only the last used-by flag was maintained instead of
making this a bitfield of all found uses.
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
This corrects the type of dev_passwd_id in GONegotiationRequest event.
This field is packed as DBUS_TYPE_UINT16 but in
wpas_dbus_interface_signals it was "i" which is DBUS_TYPE_INT32.
Signed-off-by: Nishant Chaprana <n.chaprana@samsung.com>
Android platform assigns the same socket id if the socket identifier in
conf->ctrl_interface and global->params.ctrl_interface (parameter for
android_get_control_socket) point to the same Android specific control
socket. This ends up having two eloop socket handlers registered for the
same file descriptor and thus, two attempt to receive and process each
command. This can result in unexpected failure, e.g., the prefix IFNAME=
for any command is valid for global socket handler, but results in
UNKNOWN COMMAND response from the per-interface ctrl socket handler).
Since it might be possible to end up with this type of invalid
configuration in OTA upgrade, compare the socket identifiers and do not
open the ctrl socket on the respective interface if both point to same.
This allows the Wi-Fi framework to use the global control interface.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This was already the case for most command sequences, but it was
possible for wpa_s->reassociate to be set to 1 when CTRL-RSP-* commands
were used to set identity, password, or passphrase for EAP
authentication. In such cases, ENABLE_NETWORK issued after the
connection was completed could result in a new connection attempt
(likely reconnection back to the same BSS).
Fix this by checking whether an actual connection is already present
even if wpa_s->reassociate is set when processing the ENABLE_NETWORK
command.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
It is possible for driver-based BSS selection to end up reassociating
back to the current AP. If wpa_supplicant preferred another BSS, it
would have updated the internal knowledge of the AP's WPA/RSN IE when
requesting a new connection. In the special case of existing association
and new association being with the same BSS that is different from the
wpa_supplicant preference, association event processing skipped the
WPA/RSN IE update. This could result in the following 4-way handshake
getting rejected due to incorrectly detected mismatch with AP's RSN/WPA
IE between Beacon/Probe Response frame and EAPOL-Key msg 3/4.
Fix this by updating the AP WPA/RSN IE on all association events when
driver-based BSS selection is used regardless of whether the BSSID
changes. This could also cover a theoretical case of the AP changing its
RSN/WPA IE at the very moment we try to reassociate back to the same
BSS.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
These prints were at DEBUG level (-d), but they can be very frequent, so
drop them to MSGDUMP (-dd). This allows the prints to be suppressed in
common debugging cases while still leaving them easily enablable to
debug control interface issues without having to enable excessive
debugging.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Commands like BSS and GET_NETWORK are used in some cases very frequently
and those can increase the amount of debug information from
wpa_supplicant without significant benefit. These were logged at the
DEBUG level (-d). Move logging of such read-only commands (i.e., no new
wpa_supplicant operation is started based on it) to EXCESSIVE level
(-ddd) which was already used for the PING command.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
When wpa_init() in __mesh_rsn_auth_init() failed, empty rsn->auth caused
segmentation fault due to NULL pointer dereference when wpa_deinit() was
called. Fix this by checking the pointer before executing deinit steps.
Signed-off-by: Masashi Honma <masashi.honma@gmail.com>
The RSN IE is required by IEEE Std 802.11-2012 on SAE use case:
Table 8-262 Mesh Peering Open frame Action field format
Table 8-263 Mesh Peering Confirm frame Action field format
Add the RSN IE to these frames.
Signed-off-by: Masashi Honma <masashi.honma@gmail.com>
Double the buffer length from 2048 to 4096 to match the length used
currently in wpa_supplicant. This allows wpa_gui to retrieve information
for more networks than previously.
Signed-off-by: Jouni Malinen <j@w1.fi>
This allows control interface monitors to get more detailed information
in cases where wpa_supplicant-based SME receives an Authentication frame
with non-zero status code.
Signed-off-by: Jouni Malinen <j@w1.fi>
For now, there is no support for passing extended_capa pointers through
the driver_privsep.c interface from wpa_priv. Avoid leaving bogus
pointers by explicitly clearing these on both wpa_priv and
wpa_supplicant sides.
Signed-off-by: Jouni Malinen <j@w1.fi>
Add more details into configuration comments and a runtime info message
if ap_scan=2 is used with the nl80211 driver interface.
Signed-off-by: Jouni Malinen <j@w1.fi>
This adds a new helper function wpa_ctrl_open2() that can be used
instead of wpa_ctrl_open() to override the default client socket
directory. Add optional -s<directory path> argument to hostapd_cli and
wpa_cli to allow the client socket directory to be specified.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Previously, the BSS command returned an error if the WSC IE(s) in scan
results could not be parsed. This may be not ideal for all cases, to
instead of rejecting the command completely, return all other
information apart from the WPS information in such a case.
Signed-off-by: Jouni Malinen <j@w1.fi>
scan_freq and freq_list are not parsed correctly by
wpa_config_parse_int_array() if quoted.
Patch for dbus_old_handlers.c, the same change as done by Robert Shade
<robert.shade@gmail.com> for dbus_new_handlers.c in commit
99276998fa ('dbus: Do not quote scan_freq
and freq_list').
Signed-off-by: Jiří Klimeš <jklimes@redhat.com>
While the EAPOL-Key MIC derivation was already changed from SHA256 to
SHA384 for the Suite B 192-bit AKM, KDF had not been updated similarly.
Fix this by using HMAC-SHA384 instead of HMAC-SHA256 when deriving PTK
from PMK when using the Suite B 192-bit AKM.
Signed-off-by: Jouni Malinen <j@w1.fi>
Config file is written to a temp file and then it is renamed to the
original config file. However, it is possible that the rename operation
will be commited to storage while file data will be still in cache
causing original config file to be empty or partially written in case of
a system reboot without a clean shutdown. Make this less likely to occur
by forcing the data to be written to the storage device before renaming
the file.
Signed-off-by: Dmitry Shmidt <dimitrysh@google.com>
This allows a BSS entry to be expired if the AP has changed its SSID
while maintaining the same BSSID and we are associated with the BSS.
Previously, the same BSSID was enough to mark all BSS entries from the
BSSID as in use regardless of the SSID and as such, they could remain in
the wpa_supplicant BSS table indefinitely as long as the association
remaining.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
The P2P group is not yet operating when going through GO Negotiation
exchange. Previously, an old cached scan result could be used to skip
the scan immediately after the GO Negotiation. While this is quite
unlikely to happen in practice, we can easily force a scan here now with
the generic scan_min_time mechanism. Do that to avoid any corner cases
that a previous instance of the group could have if found in cached scan
results.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
The P2P group is not yet operating when going through invitation
exchange for re-invocation. Previously, an old cached scan result could
be used to skip the scan immediately after the invitation exchange.
While this may result in the fastest possible connection, it does have
some issues with cases where the GO takes some time to start up. It
would also be at least theoretically possible for some of the BSS
parameters to be different, so having a fresh scan result from the new
GO instance may be desired in any case.
Add a mechanism to skip scan results that have been last updated before
a specific point in time and as the first user for this mechanism,
require chan results to be more recent than the invitation message
exchange for the P2P Client role in persistent group re-invocation case.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This new script can be used as an example of load testing for RADIUS
authentication servers. It can control multiple eapol_test processes
over the control interface to run EAP-TLS authentication. As an example,
the following commands would run eight instances of eapol_test
concurrently:
for i in 0 1 2 3 4 5 6 7; do
./eapol_test -T /tmp/eapol_test -i $i > eapol_test.log$i &
done
time ./eapol_test.py --ctrl /tmp/eapol_test --num 8 --iter 100
0: PASS 100
1: PASS 100
2: PASS 100
3: PASS 100
4: PASS 100
5: PASS 100
6: PASS 100
7: PASS 100
real 0m0.339s
time ./eapol_test.py --ctrl /tmp/eapol_test --num 8 --iter 100 --no-fast-reauth
0: PASS 100
1: PASS 100
2: PASS 100
3: PASS 100
4: PASS 100
5: PASS 100
6: PASS 100
7: PASS 100
real 0m1.876s
Signed-off-by: Jouni Malinen <j@w1.fi>
The -T<ctrl_iface> command line argument can now be used to start
eapol_test in mode where the configuration file is not needed and the
authentication operations are started through the control interface.
Network profile is also managed through the control interface in this
case. This can be used to provide more control for scripted RADIUS
authentication server testing.
Signed-off-by: Jouni Malinen <j@w1.fi>
The new -i<ifname> command line argument can be used to specify the name
of the interface to use. This is mainly to allow unique control
interface names to be defined without having to use multiple
directories.
Signed-off-by: Jouni Malinen <j@w1.fi>
It looks like BoringSSL has removed the AES_wrap_key(), AES_unwrap_key()
API. This broke wpa_supplicant/hostapd build since those functions from
OpenSSL were used to replace the internal AES key wrap implementation.
Add a new build configuration option
(CONFIG_OPENSSL_INTERNAL_AES_WRAP=y) to allow the internal
implementation to be used with CONFIG_OPENSSL=y build to allow build
against the latest BoringSSL version.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
wpa_s->scan_req needs to be set in these cases to get correct scanning
behavior. This is mainly needed for starting of AP mode operation
immediately in ap_scan=2 case.
This fixes an issue that was found with mac80211_hwsim test cases in the
following sequence: dbus_autoscan dbus_ap_scan_2_ap_mode_scan
Signed-off-by: Jouni Malinen <j@w1.fi>
If P2PS PD concludes to use default P2PS method wpas_p2p_scan_res_join()
ignores this value and tries to perform a redundant legacy PD.
Fix this by considering WPS_P2PS method too.
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
Reviewed-by: Ilan Peer <ilan.peer@intel.com>
Ordering the units before network.target causes them to be stopped
after network.target on shutdown. This ensures that any network
filesystems will be unmounted before wpa_supplicant is killed.
Adding Wants=network.target ensures that network.target will be included
in the active dependency graph. This is typical of units which are
involved in networking setup functions.
Signed-off-by: Mike Gilbert <floppym@gentoo.org>
This makes it easier to track the output queue state on a control
interface socket and determine what could be causing issues with running
out of space in the buffer.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
PNO was stopped by the wpa_supplicant during the connection attempts or
while handling disassociation indication. External entities, mainly, the
Android Wi-Fi framework, does not expects PNO to be stopped by other
modules. Hence, do not stop the sched_scan in these scenarios if it is
triggered externally for PNO.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
wpa_supplicant_assoc_try() would result in the currently operating AP to
get stopped if wpa_supplicant_scan() ends up getting triggered without
MANUAL_SCAN_REQ while operating an AP. With ap_scan=2, this could
resulted in unintentional stopping of AP mode operations, so check
explicitly for that case and skip the wpa_supplicant_assoc_try() call if
needed to avoid this.
Signed-off-by: Jouni Malinen <j@w1.fi>
The D-Bus Scan() handler was setting wpa_s->scan_req = MANUAL_SCAN_REQ
on the code path that used wpa_supplicant_req_scan(). However, it did
not do anything similar for the cases where
wpa_supplicant_trigger_scan() is called directly. This could result in
unexpected wpa_s->last_scan_req value and incorrect behavior especially
when using ap_scan=2 and running a scan while operating in AP mode. Fix
this by explicitly setting wpa_s->last_scan_req = MANUAL_SCAN_REQ when
using wpa_supplicant_trigger_scan() from the Scan() handler.
Signed-off-by: Jouni Malinen <j@w1.fi>
When using P2P invitation to re-invoke a persistent P2P group without
specifying the operating channel, query the driver for the preferred
frequency list, and use it to select the operating channel of the group.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
With the radio work design, it is possible for a network entry to get
disabled (e.g., DISABLE_NETWORK <id>) during the time the connect or
sme-connect radio work waits to start. Previously, only the validity of
the BSS entry and BSSID/SSID was verified when starting the actual
connection step. Add call to wpas_network_disabled() to those checks to
catch the case where the network profile is disabled.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
When starting an autonomous GO without specifying the operating channel,
query the driver for the preferred frequency list, and use it to select
the operating channel of the GO (if supported).
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
When P2PS PD with default P2PS method is done, the peer that becomes GO
should authorize the client. However, P2PS specification doesn't require
the client to include its intended interface address in PD
Request/Response. As a result, the P2P Client's interface address may not
be known and any address may need to be authorized.
Previously, client's P2P Device Address was used for authorization,
which is not correct when a dedicated interface is used for P2P Client.
This is not resulting in a connection failure, however it causes a
significant delay (until WPS_PIN_TIME_IGNORE_SEL_REG elapses). Fix this
by authorizing the intended interface address, if known; or any address,
if not known.
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
Use NULL to indicate if the address is not available instead of fixed
00:00:00:00:00:00. wpas_p2ps_prov_complete() already had code for
converting NULL to that all zeros address for event messages.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Change P2PS P2P-PROV-SHOW-PIN/P2P-PROV-ENTER-PIN event notifications
on PD Request/Response handling to meet required P2PS behavior.
The new implemented scheme:
1. For a legacy P2P provision discovery the event behavior remains
without changes
2. P2PS PD, advertiser method: DISPLAY, autoaccept: TRUE:
Advertiser: SHOW-PIN on PD request replied with a status SUCCESS
Seeker: ENTER-PIN on PD response received with a status SUCCESS
3. P2PS PD, advertiser method: DISPLAY, autoaccept: FALSE:
Advertiser: SHOW-PIN on PD request replied with a status
INFO_CURRENTLY_UNAVAILABLE
Seeker: ENTER-PIN on Follow-on PD request with a status
SUCCESS_DEFERRED
4. P2PS PD, advertiser method: KEYPAD, autoaccept: TRUE/FALSE:
Advertiser: ENTER-PIN on PD request replied with a status
INFO_CURRENTLY_UNAVAILABLE
Seeker: SHOW-PIN on PD response received with a status
INFO_CURRENTLY_UNAVAILABLE
This change in behavior breaks the existing test cases
p2ps_connect_keypad_method_nonautoaccept and
p2ps_connect_display_method_nonautoaccept. Those will be fixed in a
followup commit.
Signed-off-by: Max Stepanov <Max.Stepanov@intel.com>
Reviewed-by: Ilan Peer <ilan.peer@intel.com>
P2P_FLUSH command did not cleanly clear the p2p_go_avoid_freq data
structure, and left it in an inconsistent state, where the range field
was NULL but the num field was not 0. This would have resulted in an
invalid memory access in freq_range_list_includes().
Fix this.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
A P2P GO channel switch should not be triggered in all cases that
require channel list update. Specifically, a P2P GO CS should not
be triggered in case that the P2P GO state changed or in case that
that the P2P GO has just completed a CS.
To fix this, add reason code to wpas_p2p_channel_list_update() and
trigger CS flow only for the relevant cases.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
A newly created GO might move to another channel before the client was
able to connect to it. This creates a situation where the client
searches the GO on the channel agreed upon during GO Negotiation or
invitation signaling, while the GO is on another channel. This in turn
might lead to delayed connection or connection failure and group
removal.
Fix this by disallowing a GO CS as long as there is some activity that
should delay the switch. If a GO move is not allowed, set a timeout to
re-attempt the move.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Re-factor the code, so channel optimizations would be also triggered
upon the following changes: channel updates from the kernel,
disallow_freq interface, etc.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Update hardware features for all interfaces inside the loop, don't treat
the calling wpa_s instance specially. Perform the P2P channel list
updates after the hardware features are updated. This will prevent P2P
from relying on stale information.
Signed-off-by: Arik Nemtsov <arikx.nemtsov@intel.com>
Not all paths in wpas_p2p_init_go_params() verified that the candidate
frequency can be used for GO purposes. Fix this, and in addition
re-factor the code to put better emphasis on the frequency selection
priorities.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Remove the code that considers removing GOs from their current
channel due to frequency interference, as this is already handled
as part of the P2P channels update.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
A P2P GO interface that was instantiated after a GO Negotiation or
Invitation holds the intersection of frequencies between the GO and the
client. In case the GO is going to move to another frequency, allow it
to move only to a frequency that is also supported by the client.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Add a function to compute the group common frequencies, and
use it to update the group_common_frequencies as part of the
channel switch flows.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Upon any change in the currently used channels evaluate if a GO should
move to a different operating frequency, where the possible scenarios:
1. The frequency that the GO is currently using is no longer valid,
due to regulatory reasons, and thus the GO must be moved to some
other frequency.
2. Due to Multi Concurrent Channel (MCC) policy considerations, it would
be preferable, based on configuration settings, to prefer Same
Channel Mode (SCM) over concurrent operation in multiple channels.
The supported policies:
- prefer SCM: prefer moving the GO to a frequency used by some other
interface.
- prefer SCM if Peer supports: prefer moving the GO to a frequency
used by some other station interface iff the other station
interface is using a frequency that is common between the local and
the peer device (based on the GO Negotiation/Invitation signaling).
- Stay on the current frequency.
Currently, the GO transition to another frequency is handled by a
complete tear down and re-setup of the GO. Still need to add CSA flow to
the considerations.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
This makes it possible to use these helper functions from hostapd as
well as the current use in wpa_supplicant.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This buffer is owned by the FST module, so mark it const in the
set_ies() callback to make it clearer which component is responsible for
modifying and freeing this.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
NO_EVENTS parameter was added to STATUS command by commit
a6ab82d7b4 ('Android: Add NO_EVENTS
parameter to status command'). This patch adds handling of the new
parameter in wpa_cli so that "status no_events" can be used to specify
this parameter.
Signed-off-by: Daichi Ueura <daichi.ueura@sonymobile.com>
Currently wpa_cli connects to global control interface if -i/-p
parameters are not specified. wpa_cli on global control interface
is not useful since the prefix like "IFNAME=wlan0 " needs to be
added to some commands like "IFNAME=wlan0 scan". And, specifying
-i/-p parameters every time is annoying. To improve efficiency of
debugging, this patch enables to make wpa_cli work without extra
parameters.
If you still want to connect to global control interface,
the following command can be used instead:
$ wpa_cli -g@android:wpa_wlan0 (or -gwlan0)
Signed-off-by: Daichi Ueura <daichi.ueura@sonymobile.com>
The mesh SAE auth often fails with master branch. By bisect I found
commit eb5fee0bf5 ('SAE: Add side-channel
protection to PWE derivation with ECC') causes this issue. This does not
mean the commit has a bug. This is just a CPU resource issue.
After the commit, sae_derive_pwe_ecc() spends 101(msec) on my PC (Intel
Atom N270 1.6GHz). But dot11RSNASAERetransPeriod is 40(msec). So
auth_sae_retransmit_timer() is always called and it can causes
continuous frame exchanges. Before the commit, it was 23(msec).
On the IEEE 802.11 spec, the default value of dot11RSNASAERetransPeriod
is defined as 40(msec). But it looks short because generally mesh
functionality will be used on low spec devices. Indeed Raspberry Pi B+
(ARM ARM1176JZF-S 700MHz) requires 287(msec) for new
sae_derive_pwe_ecc().
So this patch makes the default to 1000(msec) and makes it configurable.
This issue does not occur on infrastructure SAE because the
dot11RSNASAERetransPeriod is not used on it.
Signed-off-by: Masashi Honma <masashi.honma@gmail.com>
Otherwise P2P remains in provisioning state and continues to skip
extended listening forever.
Signed-off-by: Michael Olbrich <m.olbrich@pengutronix.de>
Allow proper update for listen_reg_class and listen_channel with
changed_parameters [CFG_CHANGED_P2P_LISTEN_CHANNEL] configuration for
command received through ctrl_interface. Without this, "set
p2p_listen_channel" and "set p2p_listen_reg_class" do not update the
listen channel. The D-Bus version was already setting these flags.
Signed-off-by: Purushottam Kushwaha <p.kushwaha@samsung.com>
This variable is needed to figure out whether a wpa_supplicant interface
is for a P2P group that is (or was) connected to a specific GO. The
previous implementation was able to find such a case only when there was
an association with the GO. However, this may be needed even if there is
a temporary disconnection from the GO. Keep the GO device address
information over such temporary disconnections and only remove it on
group termination. This fixes an issue with D-Bus Peer PropertiesChanged
signals for the Groups property in case a P2P group gets removed due to
group idle timeout instead of explicit group termination command (local
request) or GO notification.
Signed-off-by: Jouni Malinen <j@w1.fi>
The P2P configuration file is wrongly set as STA configuration file,
even though a separate configuration file is mentioned with '-m' option.
Add initialization and deallocation of global.params->conf_p2p_dev to
fix this.
Signed-off-by: Gautam <gautams@broadcom.com>
The new CONFIG_NO_RC4=y build option can be used to remove all internal
hostapd and wpa_supplicant uses of RC4. It should be noted that external
uses (e.g., within a TLS library) do not get disabled when doing this.
This removes capability of supporting WPA/TKIP, dynamic WEP keys with
IEEE 802.1X, WEP shared key authentication, and MSCHAPv2 password
changes.
Signed-off-by: Jouni Malinen <j@w1.fi>
FIPS builds do not include support for MD4/MD5, so disable
EAP-TTLS/CHAP, MSCHAP, and MSCHAPV2 when CONFIG_FIPS=y is used.
Signed-off-by: Jouni Malinen <j@w1.fi>
The OpenSSL internal AES_wrap_key() and AES_unwrap_key() functions are
unfortunately not available in FIPS mode. Trying to use them results in
"aes_misc.c(83): OpenSSL internal error, assertion failed: Low level API
call to cipher AES forbidden in FIPS mode!" and process termination.
Work around this by reverting commit
f19c907822 ('OpenSSL: Implement aes_wrap()
and aes_unwrap()') changes for CONFIG_FIPS=y case. In practice, this
ends up using the internal AES key wrap/unwrap implementation through
the OpenSSL EVP API which is available in FIPS mode. When CONFIG_FIPS=y
is not used, the OpenSSL AES_wrap_key()/AES_unwrap_key() API continues
to be used to minimize code size.
Signed-off-by: Jouni Malinen <j@w1.fi>
This adds a callback function that can be used from the P2P module to
request the current preferred list of operating channels from the
driver.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
If the driver supports the preferred frequency list extension, use this
information from the driver when no explicitly configured preference
list (p2p_pref_chan) is present for P2P operating channel selection.
This commit adds this for GO Negotiation and Invitation use cases.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Commit 983422088f ('nl80211: Add means to
query preferred channels') return success if no driver wrapper callback
was provided for fetching the preferred channel list. That is
problematic since the *num argument is not updated and uninitialized
freq_list could end up getting used with arbitrary frequency values. Fix
this by returning error in case the values were not available due to
driver wrapper not implementing the function. This matches the style
used in the driver_nl80211.c implementation for the case where the
driver does not support such fetch operation.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Extend the QCA vendor specific nl80211 interface to query the preferred
frequency list from driver and add a new wpa_cli command to query this
information.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Upon GO Negotiation completion, if the remote peer becomes GO, send a
hint event over QCA vendor specific interface to inform the driver of
the likely operating channel of the P2P GO.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Add vendor command to pass SET setband command to the driver and read
the updated channel list from driver when this notification succeeds.
This allows the driver to update its internal channel lists based on
setband configuration.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This is needed when enabling TLSv1.2 support for EAP-FAST since the
SSL_export_keying_material() call does not support the needed parameters
for TLS PRF and the external-to-OpenSSL PRF needs to be used instead.
Signed-off-by: Jouni Malinen <j@w1.fi>
Report the feature capability on P2PS-PROV-START and P2PS-PROV-DONE
ctrl-iface events. A feature capability value is specified as
'feature_cap=<hex>' event parameter, where <val> is a hexadecimal
string of feature capability bytes in a PD Response frame.
Signed-off-by: Max Stepanov <Max.Stepanov@intel.com>
Reviewed-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
Reviewed-by: Ilan Peer <ilan.peer@intel.com>
Add a parameter allowing to specify a value of Coordination
Protocol Transport to P2PS_PROVISION and P2PS_PROVISION_RESP commands.
Extend the p2ps_provision structure to contain cpt_priority and
cpt_mask properties and initialize them on a P2PS PD request command.
The format of the parameter:
cpt=<cpt>[:cpt]
where <cpt> is CPT name e.g. UDP or MAC. The CPT names are listed
according to their preferences to be used for a specific P2PS session.
Signed-off-by: Max Stepanov <Max.Stepanov@intel.com>
Reviewed-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
Reviewed-by: Ilan Peer <ilan.peer@intel.com>
Add Coordination Transport Protocol parameter to P2P_SERVICE_ADD
asp command.
Extend p2ps_advertisement structure to contain CPT priorities
and a supported CPT bitmask.
The format of the new parameter:
cpt=<cpt>[:<cpt>]
where <cpt> is a name of the Coordination Protocol Transport.
This implementation supports two CPT names: UDP and MAC.
The order of specified CPTs defines their priorities where
the first one has the highest priority.
Signed-off-by: Max Stepanov <Max.Stepanov@intel.com>
Reviewed-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
Reviewed-by: Ilan Peer <ilan.peer@intel.com>
Do not allow wpa_s->fst to be replaced when processing FST-ATTACH
command for an interface that has already been attached.
Signed-off-by: Jouni Malinen <j@w1.fi>
Try to exit more quickly by avoiding execution of the action script for
any pending events if the process is requested to be killed. This may
help in avoiding hitting the two second SIGALRM workaround in eloop in
case some of the action scripts block for long period of time.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This header file is needed to get struct fst_iface_cfg and struct
fst_wpa_obj defined. While it does currently get pulled in through
ap/hostapd.h and ap/ap_config.h, a more explicit inclusion may be a
cleaner option for future.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This new mechanism can be used to combine multiple periodic AP
(including P2P GO) task into a single eloop timeout to minimize number
of wakeups for the process. hostapd gets its own periodic caller and
wpa_supplicant uses the previously added timer to trigger these calls.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Previously, one timeout per process (by default every 30 seconds) was
used P2P peer expiration and another per-interface timeout (every 10
seconds) was used to expire BSS entries. Merge these to a single
per-process timeout that triggers every 10 seconds to minimize number of
process wakeups due to periodic operations.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
The caller is not expected to free or modify the value since this is
returning a reference to a buffer maintained by the upper layer.
Signed-off-by: Jouni Malinen <j@w1.fi>
This command allows network variables to be copied from one network to
another when the networks belong to different radios. This is similar to
the per-interface DUP_NETWORK command. On the global control interface,
the command syntax is as follows:
DUP_NETWORK <src ifname> <dst ifname> <src network id> <dst network id> <variable name>
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This commit implements hostapd global control interface notifications
infrastructure. hostapd global control interface clients issue
ATTACH/DETACH commands to register and deregister with hostapd
correspondingly - the same way as for any other hostapd/wpa_supplicant
control interface.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
The new phase1 config parameter value tls_disable_tlsv1_0=1 can now be
used to disable use of TLSv1.0 for a network configuration. This can be
used to force a newer TLS version to be used. For example,
phase1="tls_disable_tlsv1_0=1 tls_disable_tlsv1_1=1" would indicate that
only TLS v1.2 is accepted.
Signed-off-by: Jouni Malinen <j@w1.fi>
A typo in wpa_scan_result_compar() caused wrong scan results sorting
(and wrong roaming decision). This fixes a copy-paste regression
introduced by commit a1b790eb9d ('Select
AP based on estimated maximum throughput').
Signed-off-by: Maital Hahn <maitalm@ti.com>
If a device may be an explicit GO, it adds the GO details in the PD
Request. First, we try to reuse an active GO. If it is not present, we
try to reuse a non-active persistent group. In the latter case, if a
dedicated P2P interface is needed, the intended address should be that
of the pending interface. However, the wpas_get_go_info() provided the
ssid->bssid address, which is the address of the P2P device. This might
result in an incorrect intended interface attribute in the PD Request in
case a separate group interface is used.
Fix this by setting group_iface variable to true only if a dedicated
interface should be used and set the attribute accordingly.
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
Reviewed-by: Max Stepanov <Max.Stepanov@intel.com>
Reviewed-by: Ilan Peer <ilan.peer@intel.com>
Validate the PD Response frame contents more thoroughly when it is used
for P2PS.
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
Reviewed-by: Max Stepanov <Max.Stepanov@intel.com>
Reviewed-by: Ilan Peer <ilan.peer@intel.com>
When persistent group is used and the peer is GO in this group,
intended interface attribute should be added to PD request/response.
Not doing so violates the spec.
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
Reviewed-by: Max Stepanov <Max.Stepanov@intel.com>
Reviewed-by: Ilan Peer <ilan.peer@intel.com>
If after P2PS PD the device should become a GO it sends P2PS-PROV-DONE
event which contains the GO interface name. If the GO isn't running yet
the device may use pending interface name. However, when the GO is
started, pending interface name will be removed.
Fix the GO interface name in P2PS-PROV-DONE event by copying the
interface name instead of saving the pointer.
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
Reviewed-by: Ilan Peer <ilan.peer@intel.com>
Call wpas_p2p_create_iface() instead of just checking p2p_no_group_iface
config value. Not doing so, resulted in an incorrect behavior when the
driver sets WPA_DRIVER_FLAGS_DEDICATED_P2P_DEVICE flag.
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
Reviewed-by: Ilan Peer <ilan.peer@intel.com>
The IPv4 header after the Ethernet header is not 32-bit aligned and the
previous version ended up accessing 32-bit members at misaligned
addresses.
Signed-off-by: Jouni Malinen <j@w1.fi>
Commit 38279bdb35 ('D-Bus: Coding style
cleanup') handled the dbus_new_handlers.c change properly, but misplaced
the second 'const' in dbus_old_handlers.c in a way that resulted in
duplicated const rather than marking the actual value const.
Signed-off-by: Jouni Malinen <j@w1.fi>
The new TEST_FAIL and GET_FAIL control interface commands can be used
similarly to the earlier TEST_ALLOC_FAIL/GET_ALLOC_FAIL design. The new
version is more generic framework allowing any function to be annotated
for failure testing with the TEST_FAIL() macro. This mechanism is only
available in builds with CONFIG_WPA_TRACE_BFD=y and
CONFIG_TESTING_OPTIONS=y. For other builds, the TEST_FAIL() macro is
defined to return 0 to allow the compiler to remove the test code from
normal production builds.
As the first test site, allow os_get_random() to be marked for failing
based on call backtrace.
Signed-off-by: Jouni Malinen <j@w1.fi>
Do not allow 40 MHz co-ex PRI/SEC switch to force us to change our PRI
channel if we have an existing connection on the selected PRI channel
since doing multi-channel concurrency is likely to cause more harm than
using different PRI/SEC selection in environment with multiple BSSes on
these two channels with mixed 20 MHz or PRI channel selection.
Signed-off-by: Jouni Malinen <j@w1.fi>
In p2p_find command line processing a loop searching for multiple
'seek=' parameters modifies cmd buffer adding '\0' terminators.
The 'freq=' parameter is handled after that and can be
lost if a 'freq=' follows 'seek=' in a command line.
Fix it by moving a handling of 'freq=' parameter to be processed
before 'seek=' handling loop.
Signed-off-by: Max Stepanov <Max.Stepanov@intel.com>
This provides more information to upper layer programs on what happens
with connection attempts in cases where the enabled networks are not
found in scan results.
Signed-off-by: Dmitry Shmidt <dimitrysh@google.com>
If BOARD_HOSTAPD_PRIVATE_LIB is not used on an Android build, we will
need to replace both the p2p functions *and* wpa_driver_nl80211_driver_cmd
in order to successfully link. Let's make the name more generic so it is
more obvious what it is used for.
Suggested-by: Dmitry Shmidt <dimitrysh@google.com>
Signed-off-by: Kevin Cernekee <cernekee@google.com>
This check explicitly for reflection attack and stops authentication
immediately if that is detected instead of continuing to the following
4-way handshake that would fail due to the attacker not knowing the key
from the SAE exchange.
Signed-off-by: Jouni Malinen <j@w1.fi>
The variables here are unsigned and as such, cannot have a negative
value. Use == 0 instead of <= 0 to make this cleaner.
Signed-off-by: Jouni Malinen <j@w1.fi>
