Decrypt the AES-SIV protected elements and verify Key-Auth. Parse and
configure keys to the driver.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This allows the FILS KEK and AAD data (nonces) to be configured to the
driver for association so that the driver can encrypt the
(Re)Association Request frame and decrypt the (Re)Association Response
frame.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Filter out get_pref_freq_list() (i.e.,
QCA_NL80211_VENDOR_SUBCMD_GET_PREFERRED_FREQ_LIST) output in case of
channel negotiation by removing channels that do not allow P2P operation
at all. Previously, only the explicitly disallowed channels were removed
and that could have resulted in selecting an operating channel that is
not allowed for P2P and failing to complete the operation to start the
group.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This implements processing of FILS Authentication frame for FILS shared
key authentication with ERP and PMKSA caching.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
ieee802_1x_encapsulate_radius() and ieee802_1x_alloc_eapol_sm() need to
be called from FILS processing.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
If a PMKSA cache entry for the target AP is available, try to use FILS
with PMKSA caching.
If an ERP key for the target AP is available, try to use FILS with
EAP-Initiate/Re-auth added as Wrapper Data element.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This was already done in the case SME in the driver is used, but the SME
code path was resetting the local WPA/RSN IE only for association. While
that was fine for existing use cases, FILS needs a new RSN IE to be set
for PMKSA caching case in Authentication frames, so clear the local IE
before starting new authentication.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This needs to be callable through the EAPOL supplicant wrappers to allow
FILS implementation to use ERP.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This implements Key-Auth derivation for (Re)Association Request frames
(see P802.11ai/D11.0 12.12.2.6.2) and (Re)Association Response frames
(see P802.11ai/D11.0 12.12.2.6.3).
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This is the PTKSA key derivation used as part of the FILS authentication
exchange. See P802.11ai/D11.0 12.12.2.5.3.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This makes it cleaner for the FILS implementation to use the same design
for setting Authentication frame elements as was already done with SAE.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Add operations to allow low level control over RF sectors in QCA DMG
(11ad) chipsets. Operations include getting/setting the configuration of
a specific sector, as well as getting/setting the selected sector which
the HW uses to communicate with a specific station.
Signed-off-by: Lior David <qca_liord@qca.qualcomm.com>
Add network id command completion support for identity, password,
new_password, pin, otp, passphrase, sim and bssid commands.
Signed-off-by: Mikael Kanstrup <mikael.kanstrup@sonymobile.com>
Add list_sta command to print addresses of all stations. Command
added to both wpa_cli and hostapd_cli.
Signed-off-by: Mikael Kanstrup <mikael.kanstrup@sonymobile.com>
Events received as an immediate result of control interface commands
end up on the control request message callback function instead of
the registered read socket. This makes for example the station list
used for complete functions for disassociate and deauthenticate out
of sync. Process events in the message callback function too to ensure
no events are missed.
Signed-off-by: Mikael Kanstrup <mikael.kanstrup@sonymobile.com>
Code for connecting/reconnecting to the hostapd control interface
is found duplicated a number of times. Create a common reconnect
helper function to avoid code duplication.
Signed-off-by: Mikael Kanstrup <mikael.kanstrup@sonymobile.com>
Whenever reconnecting the control interface the hostapd station list
is unknown as stations might have dropped or connected. Refresh the
list of stations used for command completion on cli connect, reconnect
and interface change.
Signed-off-by: Mikael Kanstrup <mikael.kanstrup@sonymobile.com>
As hostapd_cli now supports command completion add documentation
of the config option to defconfig. Disabled per default.
Signed-off-by: Mikael Kanstrup <mikael.kanstrup@sonymobile.com>
With mac_addr=0 and preassoc_mac_addr=1, the permanent MAC address
should be restored for association. Previously this did not happen when
reassociating to the same ESS.
Signed-off-by: Benjamin Richter <br@waldteufel.eu>
Scan results were not propagated to all interfaces if scan results
started a new operation, in order to prevent concurrent operations. But
this can cause other interfaces to trigger a new scan when scan results
are already available. Instead, always notify other interfaces of the
scan results, but note that new operations are not allowed.
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
There are a couple of places in wpa_supplicant/hostapd where qsort() can
be called with a NULL base pointer. This results in undefined behavior
according to the C standard and with some standard C libraries (ARM RVCT
2.2) results in a data abort/memory exception. Fix this by skipping such
calls since there is nothing needing to be sorted.
Signed-off-by: Joel Cunningham <joel.cunningham@me.com>
This was already done for most driver cases, but it is possible that the
BSSID/frequency is not forced if the driver reports BSS selection
capability (e.g., NL80211_ATTR_ROAM_SUPPORT). That could potentially
result in the driver ignoring the BSSID/frequency hint and associating
with another (incorrect) AP for the WPS provisioning step if that
another AP in the same ESS is more preferred (e.g., better signal
strength) by the driver and only one of the APs (the not preferred one)
is in active WPS registrar state.
While most drivers follow the BSSID hint for the initial connection to
an ESS, not doing it here for the WPS provisioning would break the
protocol. Fix this by enforcing a single BSSID/frequency to disallow the
driver from selecting an incorrect AP for the WPS provisioning
association.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
That function does not need the full EAP header -- it only needs to know
which EAP identifier to use in the message. Make this usable for cases
where the previous EAP message may not exist (FILS).
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This changes 4-way handshake authenticator processing to decrypt the
EAPOL-Key frames using an AEAD cipher (AES-SIV with FILS AKMs) before
processing the Key Data field. This replaces Key MIC validation for the
cases where AEAD cipher is used.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This changes 4-way handshake authenticator processing to decrypt the
EAPOL-Key frames using an AEAD cipher (AES-SIV with FILS AKMs) before
processing the Key Data field. This replaces Key MIC validation for the
cases where AEAD cipher is used. This needs to move the EAPOL-Key msg
2/4 RSN element processing to happen only after the PTK has been derived
and validated. That is done for all AKMs to avoid extra complexity with
having to maintain two code paths for this.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This modifies wpa_eapol_key_send() to use AEAD cipher (AES-SIV for FILS
AKMs) to provide both integrity protection for the EAPOL-Key frame and
encryption for the Key Data field. It should be noted that this starts
encrypting the Key Data field in EAPOL-Key message 2/4 while it remains
unencrypted (but integrity protected) in non-FILS cases. Similarly, the
empty Key Data field in EAPOL-Key message 4/4 gets encrypted for AEAD
cases.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
