"wpa_cli p2p_set per_sta_psk <0/1>" can now be used to disable/enable
use of per-device PSKs in P2P groups. This is disabled by default.
When enabled, a default passphrase is still generated by the GO for
legacy stations, but all P2P and non-P2P devices using WPS will get
a unique PSK.
This gives more protection for the P2P group by preventing clients from
being able to derive the unicast keys used by other clients. This is
also a step towards allowing specific clients to be removed from a group
reliably without having to tear down the full group to do so.
Signed-hostap: Jouni Malinen <j@w1.fi>
Even after listen duration is over, P2P module remained in
P2P_LISTEN_ONLY state, which is blocking station mode scans. Fix this by
stopping P2P listen explicitly to update p2p_state to IDLE when listen
duration expires.
Signed-hostap: Syed Asifful Dayyan <syedd@broadcom.com>
Use test_autogo to verify that P2P client is able to notice explicit
group session termination message from the GO. This would have caught
the regression in processing P2P deauthentication notifications.
Signed-hostap: Jouni Malinen <j@w1.fi>
wpa_cli filters out extra DISCONNECTED events from action scripts. This
ended up filtering out the first real DISCONNECT event in case wpa_cli
was started when wpa_supplicant was in connected state. Change wpa_cli
to allow the first disconnection event to be reported to the action
script in such case.
Signed-hostap: Jouni Malinen <j@w1.fi>
Some drivers fail to work if WEP keys are configured in a WPA network.
To avoid potentially confusing error cases, reject hostapd configuration
that enables WPA and includes parameters that would imply that WEP keys
would be set.
Signed-hostap: Jouni Malinen <j@w1.fi>
Previously, network added event was skipping during group formation.
However, this did not necessarily catch all cases of temporary P2P
network blocks. Check ssid->p2p_group to make this behavior more
consistent by avoiding all P2P groups.
Signed-hostap: Jouni Malinen <j@w1.fi>
By default, P2P is initialized for all driver interfaces and this makes
P2P getting initialized for non-P2P station interface if the supplicant
is started first on this interface. If an interface is dedicated for
non-P2P station mode, it is now possible to disable P2P initialization
by adding 'p2p_disabled=1' in the configuration file of non-P2P station
interface, irrespective of the order in which supplicant is started.
Signed-hostap: Sreenath Sharma <sreenats@broadcom.com>
This is another one of the test cases that can time out frequently
under valgrind during WPS exchange. Increase the timeout to make
false error reports less likely to occur.
Signed-hostap: Jouni Malinen <j@w1.fi>
This adds ACS support to hostapd. Currently only survey-based
algorithm is available.
To use ACS you need to enable CONFIG_ACS=y in .config and use
channel=0 (or channel=acs_survey) in hostapd.conf.
For more details see wiki page [1] or comments in src/ap/acs.c.
[1]: http://wireless.kernel.org/en/users/Documentation/acs
Signed-hostap: Michal Kazior <michal.kazior@tieto.com>
Right now in case of deauthentication from GO, immediate group removal will
happen in GC only if the deauthentication packet has a valid IE. However,
the IE in deauthentication packet is mandated only for managed P2P group.
So in normal P2P group the group removal is delayed and will happen later
only in group idle timeout.
This fixes a regression from commit
d7df0fa727 that changed the previous check
for data->deauth_info != NULL to data->deauth_info->ie != NULL.
Signed-hostap: Sreenath Sharma <sreenats@broadcom.com>
Swisscom SIM cards do not include MNC length within EF_AD, and end up
using incorrect MNC length based on the 3-digit default. Hardcode MNC
length of 2 for Switzerland, in the same manner as it was done for
Finland.
Signed-hostap: Andrejs Cainikovs <andrejs.cainikovs@sonymobile.com>
Number of crypto operations seem to take very long time in the valgrind
tests (about five seconds for public key generation for M1 and M2 on a
virtual server) and this is enough to push the test runs to hit the
timeout frequently even when there is no real error. Make this less
frequent by increasing WPS test case timeout from 15 to 30 seconds to
avoid issues based on the test scripts.
Signed-hostap: Jouni Malinen <j@w1.fi>
Number of crypto operations seem to take very long time in the valgrind
tests (about five seconds for passphrase to PSK mapping and for public
key generation for M1 and M2 on a virtual server) and this is enough to
push the test runs to hit the timeout frequently even when there is no
real error. Make this less frequent by increasing group formation
timeout from 15 to 20 seconds to avoid issues based on the test scripts
(15 + config time seconds timeout in the protocol may still kick in,
though).
Signed-hostap: Jouni Malinen <j@w1.fi>
It is possible for the peer device not to support Authentication frame
exchange even though this would be required functionality in the
standard. Furthermore, either Authentication frame may be lost. To
recover from cases where Authentication frame sequence 2 is not
received, start EAPOL Authenticator from one second timeout.
Signed-hostap: Jouni Malinen <j@w1.fi>
Wait a bit longer for wpa_supplicant/hostapd to exit and clear control
interface files separately if either any of the cleanup steps fail to do
so.
Signed-hostap: Jouni Malinen <j@w1.fi>
Instead of waiting for a fixed duration, poll hostapd/wpa_supplicant
through the control interface until they are ready to reply in order to
avoid starting test case execution too early. This is like commit
b76579e0c0 but for the concurrent P2P test
cases that were forgotten from that commit.
Signed-hostap: Jouni Malinen <j@w1.fi>
Previously, concurrent station mode scans were postponed during an
ongoing P2P group formation up to the point of completed WPS
provisioning step. This would allow a scan to be started before the P2P
client has completed association for the data connection if a scan
request were timed to hit the window between the provisioning step and
the following association. Avoid this by extending P2P-in-progress state
to continue until the first data connection has been completed as part
of group formation. Use a ten second timeout for this to avoid leaving
scans disabled indefinitely if the client fails to connect completely.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
It looks like mac80211 does not always manage to join the same IBSS and
this can result in test_ibss_rsn failures. Detect this case and try to
get the IBSSes to merge by running a scan prior to continuing with the
test case.
Signed-hostap: Jouni Malinen <j@w1.fi>
It is possible for the driver to report EAPOL frame RX before
Authentication frame RX even if the frames arrived in the opposite
order. This can result in issues in cases where both IBSS peers initiate
Authentication frame exchange at about the same time and one of the
EAPOL sessions is started before processing Authentication frame seq=1
RX. Work around this by not re-initializing EAPOL state on
Authentication (SEQ=1) RX if own Authentication frame was transmitted
within last 500 ms.
Signed-hostap: Jouni Malinen <j@w1.fi>
The handshake between STA2 and STA1 was not tracked previously. For
completeness, include that in the list of handshakes that are explicitly
waited for to complete prior to starting the connectivity tests. Since
all key setup should be done at this point, remove the extra wait before
the last connectivity test between STA1 and STA2.
Signed-hostap: Jouni Malinen <j@w1.fi>
It looks like there may not be enough time to complete this test case in
15 seconds under valgrind on a virtual host every time, so increase the
timeout to 30 seconds to get more consistent test results.
Signed-hostap: Jouni Malinen <j@w1.fi>
Instead of waiting for a fixed duration, poll hostapd/wpa_supplicant
through the control interface until they are ready to reply in order to
avoid starting test case execution too early.
Signed-hostap: Jouni Malinen <j@w1.fi>
Try to make sure new testing can be started by forcing
hostapd/wpa_supplicant to be killed with SIGKILL if needed. In addition,
wait a bit longer when killing the processes to avoid issues with the
next test run starting before the old one has been fully terminated.
Signed-hostap: Jouni Malinen <j@w1.fi>
If the device that sends the GO Negotiation Confirm becomes the GO, it
may change its operating channel preference between GO Negotiation
Request and Confirm messages based on the channel list received from us.
Previously, the peer operating channel preference was not updated in
such a case and this could result in the initial scans after GO
Negotiation using incorrect operating channel and as such, extra delay
in the connection process. Fix this by updating the operating channel
information from GO Negotiation Confirm in cases where the peer becomes
the GO.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
If there are no higher priority preference for the operating channel,
use the first pref_chan entry as the operating channel preference over
the pre-configured channel which is not really a good indication of
preference. This changes the behavior for GO Negotiation Request frame
operating channel preference value in cases where p2p_pref_chan list is
set.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
This provides status information about the negotiated group to
wpa_supplicant control interface monitors during group formation in a
form that is easier to use than having to fetch the information
separately.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
This replaces number of perror() calls with wpa_printf() to get the
error messages embedded within rest of the debug messages in the same
stream instead of pushing these to stderr which may get directed to
another location.
Signed-hostap: Jouni Malinen <j@w1.fi>
The previous design of having to provide valgrind parameter to
stop-wifi.sh did not work since the new test setup may no match the
previous one. Instead of trying to figure out what needs to be stopped
based on previous run, stop all wpa_supplicant/hostapd processes running
under valgrind unconditionally to avoid cases where new set of processes
cannot be started due to existing processed.
Signed-hostap: Jouni Malinen <j@w1.fi>
test_ibss_rsn has been failing pretty frequently due to various issues
in getting all connections up. Try to address this initially by avoiding
concurrent operations and explicitly waiting for 4-way handshake
completion before testing data connection. Once this test case is
workign more robustly, a more difficult case with concurrent operations
can be added as a separate test case.
Signed-hostap: Jouni Malinen <j@w1.fi>
This new control interface event message is used to indicate when
both 4-way handshakes have been completed with a new IBSS peer.
Signed-hostap: Jouni Malinen <j@w1.fi>
This provides global status information that is applicable to all
interfaces (e.g., P2P state). In addition, ifname/address pairs are
listed to get information of all the interfaces that are currently
managed through this wpa_supplicant instance.
Signed-hostap: Jouni Malinen <j@w1.fi>
This iterates through all interfaces and saves configuration file
updates for each interface that allows it (update_config=1).
Signed-hostap: Jouni Malinen <j@w1.fi>
This allows global parameters to be set through the global control
interface without having to use IFNAME prefix. For now, this covers
only the wifi_display parameter.
Signed-hostap: Jouni Malinen <j@w1.fi>
This makes it easier to figure out what failed and allows builbot to
integrate multiple logs and state information about the test cases.
Signed-hostap: Jouni Malinen <j@w1.fi>
There were some code paths that allowed obsolete configuration data
pointer to be maintained within EAPOL supplicant in case a network was
removed while not connection to it (i.e., wpa_s->current_ssid not
pointing to the network that was removed). This could result in use of
freed memory, e.g., from eap_sm_notify_ctrl_attached() when a new
control interface connected prior to the EAPOL supplicant configuration
pointer got updated.
Signed-hostap: Jouni Malinen <j@w1.fi>
This adds survey dump support for all frequencies
and for specific desired frequencies. This will later
be used by ACS code for spectrum heuristics.
Signed-hostap: Michal Kazior <michal.kazior@tieto.com>
This splits up the channel checking upon initialization into a few
helpers. This should make this a bit easier to follow. This also paves
the way for some initial ACS entry code.
Signed-hostap: Michal Kazior <michal.kazior@tieto.com>
Interfaces that take one or two seconds to reconfigure the link after we
set IFF_ALLMULTI or after we bring the interface up were dropping the
initial TX EAPOL packet which caused excessive delays in authentication.
This change applies to FreeBSD/DragonFly only.
Signed-hostap: Rui Paulo <rpaulo@FreeBSD.org>
Add additional input verification for the frequency parameter in
p2p_group_add (and other P2P operations for that matter). Without this
verification invalid freq could be set and not handled properly.
Signed-hostap: Ilan Peer <ilan.peer@intel.com>
In AP mode the frequency was initialized only after trying to set up the
AP which caused failure. Move AP frequency initialization to the right
place. This allows an AP mode network block without the frequency
parameter to be used with the default channel 11 being selected in that
case.
Signed-hostap: Avraham Stern <avraham.stern@intel.com>
When 'p2p_group_remove *' is called while the station interface
is connected, the flow also disconnects the station interface.
Fix this by skipping non-P2P interfaces in the iteration.
Signed-hostap: Ilan Peer <ilan.peer@intel.com>
According to WSC specification (Ver 2.0.2, section 8.3), RF Bands
attribute should be set to the specific RF band used for the current
message. Add an option to set wanted band in wps_build_rf_bands() and
add a callback to get the current band from wpa_supplicant and hostapd.
Signed-hostap: David Spinadel <david.spinadel@intel.com>
Jouni Malinen