Add explicit enum values for QCA vendor config attributes
This makes it easier to copy a subset of definitions without accidentally getting mismatching values. Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This commit is contained in:
Sunil Dutt
Jouni Malinen
parent
09b812c952
commit
8b6688847e
1 changed files with 31 additions and 31 deletions
|
|
@ -789,13 +789,13 @@ enum qca_vendor_attr_txpower_decr_db {
|
|||
* QCA_NL80211_VENDOR_SUBCMD_GET_WIFI_CONFIGURATION subcommands.
|
||||
*/
|
||||
enum qca_wlan_vendor_attr_config {
|
||||
QCA_WLAN_VENDOR_ATTR_CONFIG_INVALID,
|
||||
QCA_WLAN_VENDOR_ATTR_CONFIG_INVALID = 0,
|
||||
/* Unsigned 32-bit value to set the DTIM period.
|
||||
* Whether the wifi chipset wakes at every dtim beacon or a multiple of
|
||||
* the DTIM period. If DTIM is set to 3, the STA shall wake up every 3
|
||||
* DTIM beacons.
|
||||
*/
|
||||
QCA_WLAN_VENDOR_ATTR_CONFIG_DYNAMIC_DTIM,
|
||||
QCA_WLAN_VENDOR_ATTR_CONFIG_DYNAMIC_DTIM = 1,
|
||||
/* Unsigned 32-bit value to set the wifi_iface stats averaging factor
|
||||
* used to calculate statistics like average the TSF offset or average
|
||||
* number of frame leaked.
|
||||
|
|
@ -804,52 +804,52 @@ enum qca_wlan_vendor_attr_config {
|
|||
* For instance, when evaluating leaky APs:
|
||||
* current_avg = ((num frame received within guard time) * factor + previous_avg * (0x10000 - factor)) / 0x10000
|
||||
*/
|
||||
QCA_WLAN_VENDOR_ATTR_CONFIG_STATS_AVG_FACTOR,
|
||||
QCA_WLAN_VENDOR_ATTR_CONFIG_STATS_AVG_FACTOR = 2,
|
||||
/* Unsigned 32-bit value to configure guard time, i.e., when
|
||||
* implementing IEEE power management based on frame control PM bit, how
|
||||
* long the driver waits before shutting down the radio and after
|
||||
* receiving an ACK frame for a Data frame with PM bit set.
|
||||
*/
|
||||
QCA_WLAN_VENDOR_ATTR_CONFIG_GUARD_TIME,
|
||||
QCA_WLAN_VENDOR_ATTR_CONFIG_GUARD_TIME = 3,
|
||||
/* Unsigned 32-bit value to change the FTM capability dynamically */
|
||||
QCA_WLAN_VENDOR_ATTR_CONFIG_FINE_TIME_MEASUREMENT,
|
||||
QCA_WLAN_VENDOR_ATTR_CONFIG_FINE_TIME_MEASUREMENT = 4,
|
||||
/* Unsigned 16-bit value to configure maximum TX rate dynamically */
|
||||
QCA_WLAN_VENDOR_ATTR_CONF_TX_RATE,
|
||||
QCA_WLAN_VENDOR_ATTR_CONF_TX_RATE = 5,
|
||||
/* Unsigned 32-bit value to configure the number of continuous
|
||||
* Beacon Miss which shall be used by the firmware to penalize
|
||||
* the RSSI.
|
||||
*/
|
||||
QCA_WLAN_VENDOR_ATTR_CONFIG_PENALIZE_AFTER_NCONS_BEACON_MISS,
|
||||
QCA_WLAN_VENDOR_ATTR_CONFIG_PENALIZE_AFTER_NCONS_BEACON_MISS = 6,
|
||||
/* Unsigned 8-bit value to configure the channel avoidance indication
|
||||
* behavior. Firmware to send only one indication and ignore duplicate
|
||||
* indications when set to avoid multiple Apps wakeups.
|
||||
*/
|
||||
QCA_WLAN_VENDOR_ATTR_CONFIG_CHANNEL_AVOIDANCE_IND,
|
||||
QCA_WLAN_VENDOR_ATTR_CONFIG_CHANNEL_AVOIDANCE_IND = 7,
|
||||
/* 8-bit unsigned value to configure the maximum TX MPDU for
|
||||
* aggregation. */
|
||||
QCA_WLAN_VENDOR_ATTR_CONFIG_TX_MPDU_AGGREGATION,
|
||||
QCA_WLAN_VENDOR_ATTR_CONFIG_TX_MPDU_AGGREGATION = 8,
|
||||
/* 8-bit unsigned value to configure the maximum RX MPDU for
|
||||
* aggregation. */
|
||||
QCA_WLAN_VENDOR_ATTR_CONFIG_RX_MPDU_AGGREGATION,
|
||||
QCA_WLAN_VENDOR_ATTR_CONFIG_RX_MPDU_AGGREGATION = 9,
|
||||
/* 8-bit unsigned value to configure the Non aggregrate/11g sw
|
||||
* retry threshold (0 disable, 31 max). */
|
||||
QCA_WLAN_VENDOR_ATTR_CONFIG_NON_AGG_RETRY,
|
||||
QCA_WLAN_VENDOR_ATTR_CONFIG_NON_AGG_RETRY = 10,
|
||||
/* 8-bit unsigned value to configure the aggregrate sw
|
||||
* retry threshold (0 disable, 31 max). */
|
||||
QCA_WLAN_VENDOR_ATTR_CONFIG_AGG_RETRY,
|
||||
QCA_WLAN_VENDOR_ATTR_CONFIG_AGG_RETRY = 11,
|
||||
/* 8-bit unsigned value to configure the MGMT frame
|
||||
* retry threshold (0 disable, 31 max). */
|
||||
QCA_WLAN_VENDOR_ATTR_CONFIG_MGMT_RETRY,
|
||||
QCA_WLAN_VENDOR_ATTR_CONFIG_MGMT_RETRY = 12,
|
||||
/* 8-bit unsigned value to configure the CTRL frame
|
||||
* retry threshold (0 disable, 31 max). */
|
||||
QCA_WLAN_VENDOR_ATTR_CONFIG_CTRL_RETRY,
|
||||
QCA_WLAN_VENDOR_ATTR_CONFIG_CTRL_RETRY = 13,
|
||||
/* 8-bit unsigned value to configure the propagation delay for
|
||||
* 2G/5G band (0~63, units in us) */
|
||||
QCA_WLAN_VENDOR_ATTR_CONFIG_PROPAGATION_DELAY,
|
||||
QCA_WLAN_VENDOR_ATTR_CONFIG_PROPAGATION_DELAY = 14,
|
||||
/* Unsigned 32-bit value to configure the number of unicast TX fail
|
||||
* packet count. The peer is disconnected once this threshold is
|
||||
* reached. */
|
||||
QCA_WLAN_VENDOR_ATTR_CONFIG_TX_FAIL_COUNT,
|
||||
QCA_WLAN_VENDOR_ATTR_CONFIG_TX_FAIL_COUNT = 15,
|
||||
/* Attribute used to set scan default IEs to the driver.
|
||||
*
|
||||
* These IEs can be used by scan operations that will be initiated by
|
||||
|
|
@ -860,50 +860,50 @@ enum qca_wlan_vendor_attr_config {
|
|||
* driver. If a particular IE is present in the scan default IEs but not
|
||||
* present in the scan request, then that IE should be added to the IEs
|
||||
* sent in the Probe Request frames for that scan request. */
|
||||
QCA_WLAN_VENDOR_ATTR_CONFIG_SCAN_DEFAULT_IES,
|
||||
QCA_WLAN_VENDOR_ATTR_CONFIG_SCAN_DEFAULT_IES = 16,
|
||||
/* Unsigned 32-bit attribute for generic commands */
|
||||
QCA_WLAN_VENDOR_ATTR_CONFIG_GENERIC_COMMAND,
|
||||
QCA_WLAN_VENDOR_ATTR_CONFIG_GENERIC_COMMAND = 17,
|
||||
/* Unsigned 32-bit value attribute for generic commands */
|
||||
QCA_WLAN_VENDOR_ATTR_CONFIG_GENERIC_VALUE,
|
||||
QCA_WLAN_VENDOR_ATTR_CONFIG_GENERIC_VALUE = 18,
|
||||
/* Unsigned 32-bit data attribute for generic command response */
|
||||
QCA_WLAN_VENDOR_ATTR_CONFIG_GENERIC_DATA,
|
||||
QCA_WLAN_VENDOR_ATTR_CONFIG_GENERIC_DATA = 19,
|
||||
/* Unsigned 32-bit length attribute for
|
||||
* QCA_WLAN_VENDOR_ATTR_CONFIG_GENERIC_DATA */
|
||||
QCA_WLAN_VENDOR_ATTR_CONFIG_GENERIC_LENGTH,
|
||||
QCA_WLAN_VENDOR_ATTR_CONFIG_GENERIC_LENGTH = 20,
|
||||
/* Unsigned 32-bit flags attribute for
|
||||
* QCA_WLAN_VENDOR_ATTR_CONFIG_GENERIC_DATA */
|
||||
QCA_WLAN_VENDOR_ATTR_CONFIG_GENERIC_FLAGS,
|
||||
QCA_WLAN_VENDOR_ATTR_CONFIG_GENERIC_FLAGS = 21,
|
||||
/* Unsigned 32-bit, defining the access policy.
|
||||
* See enum qca_access_policy. Used with
|
||||
* QCA_WLAN_VENDOR_ATTR_CONFIG_ACCESS_POLICY_IE_LIST. */
|
||||
QCA_WLAN_VENDOR_ATTR_CONFIG_ACCESS_POLICY,
|
||||
QCA_WLAN_VENDOR_ATTR_CONFIG_ACCESS_POLICY = 22,
|
||||
/* Sets the list of full set of IEs for which a specific access policy
|
||||
* has to be applied. Used along with
|
||||
* QCA_WLAN_VENDOR_ATTR_CONFIG_ACCESS_POLICY to control the access.
|
||||
* Zero length payload can be used to clear this access constraint. */
|
||||
QCA_WLAN_VENDOR_ATTR_CONFIG_ACCESS_POLICY_IE_LIST,
|
||||
QCA_WLAN_VENDOR_ATTR_CONFIG_ACCESS_POLICY_IE_LIST = 23,
|
||||
/* Unsigned 32-bit, specifies the interface index (netdev) for which the
|
||||
* corresponding configurations are applied. If the interface index is
|
||||
* not specified, the configurations are attributed to the respective
|
||||
* wiphy. */
|
||||
QCA_WLAN_VENDOR_ATTR_CONFIG_IFINDEX,
|
||||
QCA_WLAN_VENDOR_ATTR_CONFIG_IFINDEX = 24,
|
||||
/* 8-bit unsigned value to trigger QPower: 1-Enable, 0-Disable */
|
||||
QCA_WLAN_VENDOR_ATTR_CONFIG_QPOWER,
|
||||
QCA_WLAN_VENDOR_ATTR_CONFIG_QPOWER = 25,
|
||||
/* 8-bit unsigned value to configure the driver and below layers to
|
||||
* ignore the assoc disallowed set by APs while connecting
|
||||
* 1-Ignore, 0-Don't ignore */
|
||||
QCA_WLAN_VENDOR_ATTR_CONFIG_IGNORE_ASSOC_DISALLOWED,
|
||||
QCA_WLAN_VENDOR_ATTR_CONFIG_IGNORE_ASSOC_DISALLOWED = 26,
|
||||
/* 32-bit unsigned value to trigger antenna diversity features:
|
||||
* 1-Enable, 0-Disable */
|
||||
QCA_WLAN_VENDOR_ATTR_CONFIG_ANT_DIV_ENA,
|
||||
QCA_WLAN_VENDOR_ATTR_CONFIG_ANT_DIV_ENA = 27,
|
||||
/* 32-bit unsigned value to configure specific chain antenna */
|
||||
QCA_WLAN_VENDOR_ATTR_CONFIG_ANT_DIV_CHAIN,
|
||||
QCA_WLAN_VENDOR_ATTR_CONFIG_ANT_DIV_CHAIN = 28,
|
||||
/* 32-bit unsigned value to trigger cycle selftest
|
||||
* 1-Enable, 0-Disable */
|
||||
QCA_WLAN_VENDOR_ATTR_CONFIG_ANT_DIV_SELFTEST,
|
||||
QCA_WLAN_VENDOR_ATTR_CONFIG_ANT_DIV_SELFTEST = 29,
|
||||
/* 32-bit unsigned to configure the cycle time of selftest
|
||||
* the unit is micro-second */
|
||||
QCA_WLAN_VENDOR_ATTR_CONFIG_ANT_DIV_SELFTEST_INTVL,
|
||||
QCA_WLAN_VENDOR_ATTR_CONFIG_ANT_DIV_SELFTEST_INTVL = 30,
|
||||
|
||||
/* keep last */
|
||||
QCA_WLAN_VENDOR_ATTR_CONFIG_AFTER_LAST,
|
||||
|
|
|
|||
Loading…
Reference in a new issue