diff --git a/src/common/qca-vendor.h b/src/common/qca-vendor.h index c458cb32b..adaec890b 100644 --- a/src/common/qca-vendor.h +++ b/src/common/qca-vendor.h @@ -789,13 +789,13 @@ enum qca_vendor_attr_txpower_decr_db { * QCA_NL80211_VENDOR_SUBCMD_GET_WIFI_CONFIGURATION subcommands. */ enum qca_wlan_vendor_attr_config { - QCA_WLAN_VENDOR_ATTR_CONFIG_INVALID, + QCA_WLAN_VENDOR_ATTR_CONFIG_INVALID = 0, /* Unsigned 32-bit value to set the DTIM period. * Whether the wifi chipset wakes at every dtim beacon or a multiple of * the DTIM period. If DTIM is set to 3, the STA shall wake up every 3 * DTIM beacons. */ - QCA_WLAN_VENDOR_ATTR_CONFIG_DYNAMIC_DTIM, + QCA_WLAN_VENDOR_ATTR_CONFIG_DYNAMIC_DTIM = 1, /* Unsigned 32-bit value to set the wifi_iface stats averaging factor * used to calculate statistics like average the TSF offset or average * number of frame leaked. @@ -804,52 +804,52 @@ enum qca_wlan_vendor_attr_config { * For instance, when evaluating leaky APs: * current_avg = ((num frame received within guard time) * factor + previous_avg * (0x10000 - factor)) / 0x10000 */ - QCA_WLAN_VENDOR_ATTR_CONFIG_STATS_AVG_FACTOR, + QCA_WLAN_VENDOR_ATTR_CONFIG_STATS_AVG_FACTOR = 2, /* Unsigned 32-bit value to configure guard time, i.e., when * implementing IEEE power management based on frame control PM bit, how * long the driver waits before shutting down the radio and after * receiving an ACK frame for a Data frame with PM bit set. */ - QCA_WLAN_VENDOR_ATTR_CONFIG_GUARD_TIME, + QCA_WLAN_VENDOR_ATTR_CONFIG_GUARD_TIME = 3, /* Unsigned 32-bit value to change the FTM capability dynamically */ - QCA_WLAN_VENDOR_ATTR_CONFIG_FINE_TIME_MEASUREMENT, + QCA_WLAN_VENDOR_ATTR_CONFIG_FINE_TIME_MEASUREMENT = 4, /* Unsigned 16-bit value to configure maximum TX rate dynamically */ - QCA_WLAN_VENDOR_ATTR_CONF_TX_RATE, + QCA_WLAN_VENDOR_ATTR_CONF_TX_RATE = 5, /* Unsigned 32-bit value to configure the number of continuous * Beacon Miss which shall be used by the firmware to penalize * the RSSI. */ - QCA_WLAN_VENDOR_ATTR_CONFIG_PENALIZE_AFTER_NCONS_BEACON_MISS, + QCA_WLAN_VENDOR_ATTR_CONFIG_PENALIZE_AFTER_NCONS_BEACON_MISS = 6, /* Unsigned 8-bit value to configure the channel avoidance indication * behavior. Firmware to send only one indication and ignore duplicate * indications when set to avoid multiple Apps wakeups. */ - QCA_WLAN_VENDOR_ATTR_CONFIG_CHANNEL_AVOIDANCE_IND, + QCA_WLAN_VENDOR_ATTR_CONFIG_CHANNEL_AVOIDANCE_IND = 7, /* 8-bit unsigned value to configure the maximum TX MPDU for * aggregation. */ - QCA_WLAN_VENDOR_ATTR_CONFIG_TX_MPDU_AGGREGATION, + QCA_WLAN_VENDOR_ATTR_CONFIG_TX_MPDU_AGGREGATION = 8, /* 8-bit unsigned value to configure the maximum RX MPDU for * aggregation. */ - QCA_WLAN_VENDOR_ATTR_CONFIG_RX_MPDU_AGGREGATION, + QCA_WLAN_VENDOR_ATTR_CONFIG_RX_MPDU_AGGREGATION = 9, /* 8-bit unsigned value to configure the Non aggregrate/11g sw * retry threshold (0 disable, 31 max). */ - QCA_WLAN_VENDOR_ATTR_CONFIG_NON_AGG_RETRY, + QCA_WLAN_VENDOR_ATTR_CONFIG_NON_AGG_RETRY = 10, /* 8-bit unsigned value to configure the aggregrate sw * retry threshold (0 disable, 31 max). */ - QCA_WLAN_VENDOR_ATTR_CONFIG_AGG_RETRY, + QCA_WLAN_VENDOR_ATTR_CONFIG_AGG_RETRY = 11, /* 8-bit unsigned value to configure the MGMT frame * retry threshold (0 disable, 31 max). */ - QCA_WLAN_VENDOR_ATTR_CONFIG_MGMT_RETRY, + QCA_WLAN_VENDOR_ATTR_CONFIG_MGMT_RETRY = 12, /* 8-bit unsigned value to configure the CTRL frame * retry threshold (0 disable, 31 max). */ - QCA_WLAN_VENDOR_ATTR_CONFIG_CTRL_RETRY, + QCA_WLAN_VENDOR_ATTR_CONFIG_CTRL_RETRY = 13, /* 8-bit unsigned value to configure the propagation delay for * 2G/5G band (0~63, units in us) */ - QCA_WLAN_VENDOR_ATTR_CONFIG_PROPAGATION_DELAY, + QCA_WLAN_VENDOR_ATTR_CONFIG_PROPAGATION_DELAY = 14, /* Unsigned 32-bit value to configure the number of unicast TX fail * packet count. The peer is disconnected once this threshold is * reached. */ - QCA_WLAN_VENDOR_ATTR_CONFIG_TX_FAIL_COUNT, + QCA_WLAN_VENDOR_ATTR_CONFIG_TX_FAIL_COUNT = 15, /* Attribute used to set scan default IEs to the driver. * * These IEs can be used by scan operations that will be initiated by @@ -860,50 +860,50 @@ enum qca_wlan_vendor_attr_config { * driver. If a particular IE is present in the scan default IEs but not * present in the scan request, then that IE should be added to the IEs * sent in the Probe Request frames for that scan request. */ - QCA_WLAN_VENDOR_ATTR_CONFIG_SCAN_DEFAULT_IES, + QCA_WLAN_VENDOR_ATTR_CONFIG_SCAN_DEFAULT_IES = 16, /* Unsigned 32-bit attribute for generic commands */ - QCA_WLAN_VENDOR_ATTR_CONFIG_GENERIC_COMMAND, + QCA_WLAN_VENDOR_ATTR_CONFIG_GENERIC_COMMAND = 17, /* Unsigned 32-bit value attribute for generic commands */ - QCA_WLAN_VENDOR_ATTR_CONFIG_GENERIC_VALUE, + QCA_WLAN_VENDOR_ATTR_CONFIG_GENERIC_VALUE = 18, /* Unsigned 32-bit data attribute for generic command response */ - QCA_WLAN_VENDOR_ATTR_CONFIG_GENERIC_DATA, + QCA_WLAN_VENDOR_ATTR_CONFIG_GENERIC_DATA = 19, /* Unsigned 32-bit length attribute for * QCA_WLAN_VENDOR_ATTR_CONFIG_GENERIC_DATA */ - QCA_WLAN_VENDOR_ATTR_CONFIG_GENERIC_LENGTH, + QCA_WLAN_VENDOR_ATTR_CONFIG_GENERIC_LENGTH = 20, /* Unsigned 32-bit flags attribute for * QCA_WLAN_VENDOR_ATTR_CONFIG_GENERIC_DATA */ - QCA_WLAN_VENDOR_ATTR_CONFIG_GENERIC_FLAGS, + QCA_WLAN_VENDOR_ATTR_CONFIG_GENERIC_FLAGS = 21, /* Unsigned 32-bit, defining the access policy. * See enum qca_access_policy. Used with * QCA_WLAN_VENDOR_ATTR_CONFIG_ACCESS_POLICY_IE_LIST. */ - QCA_WLAN_VENDOR_ATTR_CONFIG_ACCESS_POLICY, + QCA_WLAN_VENDOR_ATTR_CONFIG_ACCESS_POLICY = 22, /* Sets the list of full set of IEs for which a specific access policy * has to be applied. Used along with * QCA_WLAN_VENDOR_ATTR_CONFIG_ACCESS_POLICY to control the access. * Zero length payload can be used to clear this access constraint. */ - QCA_WLAN_VENDOR_ATTR_CONFIG_ACCESS_POLICY_IE_LIST, + QCA_WLAN_VENDOR_ATTR_CONFIG_ACCESS_POLICY_IE_LIST = 23, /* Unsigned 32-bit, specifies the interface index (netdev) for which the * corresponding configurations are applied. If the interface index is * not specified, the configurations are attributed to the respective * wiphy. */ - QCA_WLAN_VENDOR_ATTR_CONFIG_IFINDEX, + QCA_WLAN_VENDOR_ATTR_CONFIG_IFINDEX = 24, /* 8-bit unsigned value to trigger QPower: 1-Enable, 0-Disable */ - QCA_WLAN_VENDOR_ATTR_CONFIG_QPOWER, + QCA_WLAN_VENDOR_ATTR_CONFIG_QPOWER = 25, /* 8-bit unsigned value to configure the driver and below layers to * ignore the assoc disallowed set by APs while connecting * 1-Ignore, 0-Don't ignore */ - QCA_WLAN_VENDOR_ATTR_CONFIG_IGNORE_ASSOC_DISALLOWED, + QCA_WLAN_VENDOR_ATTR_CONFIG_IGNORE_ASSOC_DISALLOWED = 26, /* 32-bit unsigned value to trigger antenna diversity features: * 1-Enable, 0-Disable */ - QCA_WLAN_VENDOR_ATTR_CONFIG_ANT_DIV_ENA, + QCA_WLAN_VENDOR_ATTR_CONFIG_ANT_DIV_ENA = 27, /* 32-bit unsigned value to configure specific chain antenna */ - QCA_WLAN_VENDOR_ATTR_CONFIG_ANT_DIV_CHAIN, + QCA_WLAN_VENDOR_ATTR_CONFIG_ANT_DIV_CHAIN = 28, /* 32-bit unsigned value to trigger cycle selftest * 1-Enable, 0-Disable */ - QCA_WLAN_VENDOR_ATTR_CONFIG_ANT_DIV_SELFTEST, + QCA_WLAN_VENDOR_ATTR_CONFIG_ANT_DIV_SELFTEST = 29, /* 32-bit unsigned to configure the cycle time of selftest * the unit is micro-second */ - QCA_WLAN_VENDOR_ATTR_CONFIG_ANT_DIV_SELFTEST_INTVL, + QCA_WLAN_VENDOR_ATTR_CONFIG_ANT_DIV_SELFTEST_INTVL = 30, /* keep last */ QCA_WLAN_VENDOR_ATTR_CONFIG_AFTER_LAST,