From 5f2c0a22a92b33d69322cd2ff1d7530b717f1be6 Mon Sep 17 00:00:00 2001 From: Jouni Malinen Date: Sun, 4 Dec 2016 20:50:07 +0200 Subject: [PATCH] Sync with mac80211-next.git include/uapi/linux/nl80211.h This brings in nl80211 definitions as of 2016-12-02. Signed-off-by: Jouni Malinen --- src/drivers/nl80211_copy.h | 29 +++++++++++++++++++++++++++++ 1 file changed, 29 insertions(+) diff --git a/src/drivers/nl80211_copy.h b/src/drivers/nl80211_copy.h index a268a0095..259c9c77f 100644 --- a/src/drivers/nl80211_copy.h +++ b/src/drivers/nl80211_copy.h @@ -600,6 +600,20 @@ * * @NL80211_CMD_SET_WDS_PEER: Set the MAC address of the peer on a WDS interface. * + * @NL80211_CMD_SET_MULTICAST_TO_UNICAST: Configure if this AP should perform + * multicast to unicast conversion. When enabled, all multicast packets + * with ethertype ARP, IPv4 or IPv6 (possibly within an 802.1Q header) + * will be sent out to each station once with the destination (multicast) + * MAC address replaced by the station's MAC address. Note that this may + * break certain expectations of the receiver, e.g. the ability to drop + * unicast IP packets encapsulated in multicast L2 frames, or the ability + * to not send destination unreachable messages in such cases. + * This can only be toggled per BSS. Configure this on an interface of + * type %NL80211_IFTYPE_AP. It applies to all its VLAN interfaces + * (%NL80211_IFTYPE_AP_VLAN), except for those in 4addr (WDS) mode. + * If %NL80211_ATTR_MULTICAST_TO_UNICAST_ENABLED is not present with this + * command, the feature is disabled. + * * @NL80211_CMD_JOIN_MESH: Join a mesh. The mesh ID must be given, and initial * mesh config parameters may be given. * @NL80211_CMD_LEAVE_MESH: Leave the mesh network -- no special arguments, the @@ -874,6 +888,12 @@ * This will contain a %NL80211_ATTR_NAN_MATCH nested attribute and * %NL80211_ATTR_COOKIE. * + * @NL80211_CMD_UPDATE_CONNECT_PARAMS: Update one or more connect parameters + * for subsequent roaming cases if the driver or firmware uses internal + * BSS selection. This command can be issued only while connected and it + * does not result in a change for the current association. Currently, + * only the %NL80211_ATTR_IE data is used and updated with this command. + * * @NL80211_CMD_MAX: highest used command number * @__NL80211_CMD_AFTER_LAST: internal use */ @@ -1069,6 +1089,10 @@ enum nl80211_commands { NL80211_CMD_CHANGE_NAN_CONFIG, NL80211_CMD_NAN_MATCH, + NL80211_CMD_SET_MULTICAST_TO_UNICAST, + + NL80211_CMD_UPDATE_CONNECT_PARAMS, + /* add new commands above here */ /* used to define NL80211_CMD_MAX below */ @@ -1950,6 +1974,9 @@ enum nl80211_commands { * Request/Response frame protection. This attribute contains the 16 octet * STA Nonce followed by 16 octets of AP Nonce. * + * @NL80211_ATTR_MULTICAST_TO_UNICAST_ENABLED: Indicates whether or not multicast + * packets should be send out as unicast to all stations (flag attribute). + * * @NUM_NL80211_ATTR: total number of nl80211_attrs available * @NL80211_ATTR_MAX: highest attribute number currently defined * @__NL80211_ATTR_AFTER_LAST: internal use @@ -2352,6 +2379,8 @@ enum nl80211_attrs { NL80211_ATTR_FILS_KEK, NL80211_ATTR_FILS_NONCES, + NL80211_ATTR_MULTICAST_TO_UNICAST_ENABLED, + /* add attributes here, update the policy in nl80211.c */ __NL80211_ATTR_AFTER_LAST,