Projet_SETI_RISC-V/neorv32/docs/userguide/customizing_the_bootloader.adoc
2023-03-06 14:48:14 +01:00

73 lines
4.3 KiB
Text

<<<
:sectnums:
== Customizing the Internal Bootloader
The NEORV32 bootloader provides several options to configure and customize it for a certain application setup.
This configuration is done by passing _defines_ when compiling the bootloader. Of course you can also
modify to bootloader source code to provide a setup that perfectly fits your needs.
[IMPORTANT]
Each time the bootloader sources are modified, the bootloader has to be re-compiled (and re-installed to the
bootloader ROM) and the processor has to be re-synthesized.
[NOTE]
Keep in mind that the maximum size for the bootloader is limited to 32kB and should be compiled using the
base ISA `rv32i` only to ensure it can work independently of the actual CPU configuration.
.Bootloader configuration parameters
[cols="<2,^1,^2,<6"]
[options="header", grid="rows"]
|=======================
| Parameter | Default | Legal values | Description
4+^| Serial console interface
| `UART_EN` | `1` | `0`, `1` | Set to `0` to disable UART0 (no serial console at all)
| `UART_BAUD` | `19200` | _any_ | Baud rate of UART0
4+^| Status LED
| `STATUS_LED_EN` | `1` | `0`, `1` | Enable bootloader status led ("heart beat") at `GPIO` output port pin #`STATUS_LED_PIN` when `1`
| `STATUS_LED_PIN` | `0` | `0` ... `31` | `GPIO` output pin used for the high-active status LED
4+^| Auto-boot configuration
| `AUTO_BOOT_TIMEOUT` | `8` | _any_ | Time in seconds after the auto-boot sequence starts (if there is no UART input by the user); set to 0 to disabled auto-boot sequence
4+^| SPI configuration
| `SPI_EN` | `1` | `0`, `1` | Set `1` to enable the usage of the SPI module (including load/store executables from/to SPI flash options)
| `SPI_FLASH_CS` | `0` | `0` ... `7` | SPI chip select output (`spi_csn_o`) for selecting flash
| `SPI_FLASH_ADDR_BYTES` | `3` | `2`, `3`, `4` | SPI flash address size in number of bytes (2=16-bit, 3=24-bit, 4=32-bit)
| `SPI_FLASH_SECTOR_SIZE` | `65536` | _any_ | SPI flash sector size in bytes
| `SPI_FLASH_CLK_PRSC` | `CLK_PRSC_8` | `CLK_PRSC_2` `CLK_PRSC_4` `CLK_PRSC_8` `CLK_PRSC_64` `CLK_PRSC_128` `CLK_PRSC_1024` `CLK_PRSC_2024` `CLK_PRSC_4096` | SPI clock pre-scaler (dividing main processor clock)
| `SPI_BOOT_BASE_ADDR` | `0x00400000` | _any_ 32-bit value | Defines the _base_ address of the executable in external flash
4+^| XIP configuration
| `XIP_EN` | `0` | `0`, `1` | Set `1` to enable the XIP options
| `XIP_PAGE_BASE_ADDR` | `0x40000000` | _any_ 32-bit value | Defines the page _base_ address where the XP flash will be mapped to
|=======================
[NOTE]
The XIP options re-use the "SPI configuration" options for configuring the XIP's SPI connection.
Each configuration parameter is implemented as C-language `define` that can be manually overridden (_redefined_) when
invoking the bootloader's makefile. The according parameter and its new value has to be _appended_
(using `+=`) to the makefile `USER_FLAGS` variable. Make sure to use the `-D` prefix here.
For example, to configure a UART Baud rate of 57600 and redirecting the status LED to GPIO output pin 20
use the following command:
.Example: customizing, re-compiling and re-installing the bootloader
[source,console]
----
sw/bootloader$ make USER_FLAGS+=-DUART_BAUD=57600 USER_FLAGS+=-DSTATUS_LED_PIN=20 clean_all bootloader
----
[NOTE]
The `clean_all` target ensure that all libraries are re-compiled. The `bootloader` target will automatically
compile and install the bootloader to the HDL boot ROM (updating `rtl/core/neorv32_bootloader_image.vhd`).
:sectnums:
=== Auto-Boot Configuration
The default bootloader provides a UART-based user interface that allows to upload new executables
at any time. Optionally, the executable can also be programmed to an external SPI flash by the bootloader (see
section <<_programming_an_external_spi_flash_via_the_bootloader>>).
The bootloader also provides an _automatic boot sequence_ (auto-boot) which will start copying an executable
from external SPI flash to IMEM using the default SPI configuration. By this, the default bootloader
provides a "non-volatile program storage" mechanism that automatically boots from external SPI flash
(after `AUTO_BOOT_TIMEOUT`) while still providing the option to re-program the SPI flash at any time
via the UART console.