A new hostapd configuration parameter, disable_pmksa_caching=1, can now
be used to disable PMKSA caching on the Authenticator. This forces the
stations to complete EAP authentication on every association when WPA2
is being used.
Windows 7 uses incorrect way of figuring out AP's WPS capabilities by
acting as a Registrar and using M1 from the AP. The config methods
attribute in that message is supposed to indicate only the configuration
method supported by the AP in Enrollee role, i.e., to add an external
Registrar. For that case, PBC shall not be used and as such, the
PushButton config method is removed from M1 by default. If pbc_in_m1=1
is included in the configuration file, the PushButton config method is
left in M1 (if included in config_methods parameter) to allow Windows 7
to use PBC instead of PIN (e.g., from a label in the AP).
CFLAGS += -DCONFIG_RSN_TESTING in .config and rsn_testing=1 in
hostapd.conf can now be used to enable a testing mode that adds
extensions to RSN element. This can be used to check whether
station implementations are incompatible with future extensions
to the RSN element.
Instead of converting back and forth from the string representation,
always use the binary representation internally.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
In multi BSS setups it wasn't possible to set up an HT BSS in
conjunction with a WEP/TKIP BSS. HT needed to be turned off entirely
to allow WEP/TKIP BSSes to be used.
In order to allow HT BSSes to coexist with non-HT WEP/TKIP BSSes add a
new BSS conf attribute "disable_11n" which disables HT capabilities on a
single BSS by suppressing HT IEs in the beacon and probe response
frames. Furthermore, mark all STAs associated to a WEP/TKIP BSS as
non-HT STAs. The disable_11n parameter is used internally; no new entry
is parsed from hostapd.conf.
This allows a non-HT WEP/TKIP BSS to coexist with a HT BSS without
having to disable HT mode entirely. Nevertheless, all STAs associated to
the WEP/TKIP BSS will only be served as if they were non-HT STAs.
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
If WMM is not disabled explicitly (wmm_enabled=0 in hostapd.conf),
enable WMM automatically whenever HT (ieee80211n) is enabled. Use
the default WMM parameters for AP TX queues and the EDCA parameters
advertised for stations in WMM IE if no overriding values are
included in the configuration.
tdls_prohibit=1 and tdls_prohibit_chan_switch=1 and now be used to
disable use of TDLS or TDLS channel switching in the BSS using
extended cabilities IE as defined in IEEE 802.11z.
The nl80211 driver can report low ACK condition (in fact it reports
complete loss right now only). Use that, along with a config option, to
disconnect stations when the data connection is not working properly,
e.g., due to the STA having went outside the range of the AP. This is
disabled by default and can be enabled with disassoc_low_ack=1 in
hostapd or wpa_supplicant configuration file.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
WFA 11n testing does not allow WEP when IEEE 802.11n is enabled.
Reject such combination when parsing hostapd configuration file.
Signed-off-by: Yogesh Ashok Powar <yogeshp@marvell.com>
These are not used by any driver wrapper, i.e., only the four
data queues (BK, BE, VI, VO) are configurable. Better remove these
so that there is no confusion about being able to configure
something additional.
This is an option to continue with wpa_supplicant and hostapd even if
config file has errors. The problem is that these daemons are the best
"candidates" for the config change, so if they can not start because
config file was let's say corrupted, you can not fix it easily.
Signed-off-by: Dmitry Shmidt <dimitrysh@google.com>
hostapd does not implement UAPSD functionality. However, if U-APSD
functionality is implemented outside hostapd, add support to advertise
the functionality in beacon.
Signed-off-by: yogeshp@marvell.com
Doxygen and some build tools may get a bit confused about same file
name being used in different directories. Clean this up a bit by
renaming some of the duplicated file names in src/ap.
This code can be shared by both hostapd and wpa_supplicant and this
is an initial step in getting the generic code moved to be under the
src directories. Couple of generic files still remain under the
hostapd directory due to direct dependencies to files there. Once the
dependencies have been removed, they will also be moved to the src/ap
directory to allow wpa_supplicant to be built without requiring anything
from the hostapd directory.
config.c includes now only the generic helper functions that are needed
both for hostapd and the AP mode operations in wpa_supplicant.
hostapd/config_file.c is only needed for hostapd.
