Make it more difficult to miss issues that were previously only printed
out in /tmp/hwsim-test-logs/*-parallel.log. This covers things like
memory leaks and test script failures or forgotten development time
prints to stdout.
Signed-off-by: Jouni Malinen <j@w1.fi>
This test case was missing an explicit CAPI ap_reset_default and that
could result in hostapd being left running at the end of the test case.
This could result in issues with following test cases if they used a new
radio interface from HWSimRadio().
Signed-off-by: Jouni Malinen <j@w1.fi>
Raising an exception while the wlan5 interface was remove (i.e., between
wpas.interface_remove() and .interface_add() calls) would result in the
cleanup code failing and generating yet another exception while the
first one was being processed. Work around this by re-adding the wlan5
interface back temporarily if the interface is not available for the
cleanup operations.
Signed-off-by: Jouni Malinen <j@w1.fi>
These commands were being issues to incorrect wpa_supplicant instance
and were missing clearing of the MAC_RAND_SCAN parameter.
Signed-off-by: Jouni Malinen <j@w1.fi>
The iteration of WpaSupplicant instances used incorrect variable and
ended up cleaning up only the wlan5 interface. This left unexpected
setband parameter for wlan0/wlan1/wlan2 which could result in
consecutive test cases failing due to scan not finding the expected
BSSs.
Signed-off-by: Jouni Malinen <j@w1.fi>
It was possible for these test cases to fail if the first scan iteration
did not find the AP since the 10 second timeout was small enough to
terminate the second attempt before fetching the scan results. Increase
this timeout to allow at least two full scan iterations to be completed
before declaring failure.
Signed-off-by: Jouni Malinen <j@w1.fi>
These test cases use hidden SSIDs and left behind a BSS entry with no
SSID. That can cause issues for consecutive test cases where the BSSID
can be used as the key for finding a BSS entry. That could end up
picking the old hidden SSID BSS instead of the one that was meant to be
used in the test case.
Flush the scan cache at the end of the scan-ssid-list test cases to
reduce invalid test failures for the consecutive test cases.
Signed-off-by: Jouni Malinen <j@w1.fi>
The PASN_START command can fail if there is an old BSS entry for the
same BSSID from an earlier test case. Try to avoid this by flushing the
scan results before running these test cases.
Signed-off-by: Jouni Malinen <j@w1.fi>
The isAlive() function is deprecated in newer versions of Python
so replace it with the is_alive() instead.
Signed-off-by: Oren Givon <oren.givon@intel.com>
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
Need to clear sae_groups parameter before using SAE in this test case to
avoid issues if previous test cases have left a specific group
configured.
Signed-off-by: Jouni Malinen <j@w1.fi>
This could fail in theory if running out of memory, so better check for
this explicitly instead of allowing the exchange to continue and fail
later due to checkcode mismatch.
Signed-off-by: Jouni Malinen <j@w1.fi>
Add test cases that check preCAC, which is available for EU regulatory
domain. Also confirm that preCAC is not used for US.
Signed-off-by: Janusz Dziedzic <janusz.dziedzic@gmail.com>
Add option to:
- add a new AP on the same phy that the backhaul-sta uses
- run CSA from the parent
Adding a new AP (backhaul/fronthaul) on the same phy we have for
backhaul-sta is closer to the real repeater implementation.
Add a test case for that and run CSA.
This is a common problem when we have on the same phy:
- connected backhaul STA
- we started fronthaul/backhaul AP
- we receive (from parent) CSA on the STA interface
This is multi_ap_wps_shared_apdev_csa test case, which fails today with
both mac80211_hwsim and ath9k. To avoid always failing test cases,
ignore this failure for now. Full validation can be enabled once the
issue behind this is fixed.
Signed-off-by: Janusz Dziedzic <janusz.dziedzic@gmail.com>
Pass the backhaul parameters as a parameter. This is in preparation for
channel switch test for Multi AP.
Signed-off-by: Janusz Dziedzic <janusz.dziedzic@gmail.com>
This test first configure hostapd with an initial SSID
('test-wpa2-psk-start'). Then a new SSID is configured
('test-wpa2-psk-new') using SET and RELOAD. Next, a station is
associated using WPS, and the test verifies that the new SSID was served
to the station.
Signed-off-by: Raphaël Mélotte <raphael.melotte@mind.be>
cfg80211 may ignore user hints while there are active COUNTRY_IE hints,
thus at some timings it may ignore the country setting back to world
domain. Fix it by making sure the country is set only after all the
interfaces are stopped. In addition, call a more robust
clear_regdom_dev() function.
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
Test that if notify_mgmt_frames is enabled and a station connects we do
get AP-MGMT-FRAME-RECEIVED, and that it includes an Authentication
frame.
Also test that if notify_mgmt_frames is disabled, no Management frame is
sent on ctrl_iface when a station connects.
Signed-off-by: Raphaël Mélotte <raphael.melotte@mind.be>
The P2P group may be originally formed on UNII-3, so disabling UNII-1
and UNII-2 will not result in a channel switch failing the test.
Fix this by setting 44 as a preferred channel.
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
The test configures ft_r0_key_lifetime parameter, however ft_params
already contain the r0_key_lifetime. Since both options are accepted by
hostapd and set the same field, one of them gets overwritten.
As the dictionary enumeration order is not guaranteed in python, the
test may sporadically fail.
Fix that by explicitely removing the unneeded parameter.
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
