This allows the binary sizes to be reduced if no support for nl80211
vendor extensions are needed.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This adds CONFIG_ELOOP_POLL=y and CONFIG_ELOOP_EPOLL=y options to
hostapd build options similarly to how these were implemented for
wpa_supplicant.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Derive rRK and rIK on EAP server if ERP is enabled and use these keys to
allow EAP re-authentication to be used and to derive rMSK.
The new hostapd configuration parameter eap_server_erp=1 can now be used
to configure the integrated EAP server to derive EMSK, rRK, and rIK at
the successful completion of an EAP authentication method. This
functionality is not included in the default build and can be enabled
with CONFIG_ERP=y.
Signed-off-by: Jouni Malinen <j@w1.fi>
Number of documentation and configuration files had references to the
madwifi driver interface that was removed in the previous commit. Remove
these references as well.
Signed-off-by: Jouni Malinen <j@w1.fi>
There is not much point in building devices with WPS 1.0 only supported
nowadays. As such, there is not sufficient justification for maintaining
extra complexity for the CONFIG_WPS2 build option either. Remove this by
enabling WSC 2.0 support unconditionally.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
IEEE 802.11w is ratified since 2009 already, so this comment does not
seem to be valid anymore.
Signed-hostap: Helmut Schaa <helmut.schaa@googlemail.com>
This debugging mechanism has now been deprecated by the control
interface commands that can be used to fetch same internal information
from hostapd in a more convenient way. Leave the empty USR1 signal
handler and configuration file parameter for backwards compatibility.
They can be removed in future versions of hostapd.
Signed-hostap: Jouni Malinen <j@w1.fi>
Just like wpa_supplicant, give hostapd the -T option to
send all debug messages into the Linux tracing buffer.
Enable this option for hwsim test builds by default.
Signed-hostap: Johannes Berg <johannes.berg@intel.com>
This adds ACS support to hostapd. Currently only survey-based
algorithm is available.
To use ACS you need to enable CONFIG_ACS=y in .config and use
channel=0 (or channel=acs_survey) in hostapd.conf.
For more details see wiki page [1] or comments in src/ap/acs.c.
[1]: http://wireless.kernel.org/en/users/Documentation/acs
Signed-hostap: Michal Kazior <michal.kazior@tieto.com>
In order to test clients in scenarios where APs may (randomly)
drop certain management frames, introduce some testing options
into the hostapd configuration that can make it ignore certain
frames. For now, these are probe requests, authentication and
(re)association frames.
Signed-hostap: Johannes Berg <johannes.berg@intel.com>
CONFIG_SQLITE=y option can now be used to allow the eap_user_file text
file to be replaced with a SQLite database
(eap_user_file=sqlite:/path/to/sqlite.db). hostapd.eap_user_sqlite
shows an example of how the database tables can be created for this
purpose. This commit does not yet include full functionality of the
text file format, but at least basic EAP-TTLS/MSCHAPv2 style
authentication mechanisms with plaintext passwords can be used for
tests.
Signed-hostap: Jouni Malinen <j@w1.fi>
An SQLite database can now be used to manage the Milenage information
instead of a text file. The new hlr_auc_gw.txt document describes how
this is configured and used.
Signed-hostap: Jouni Malinen <j@w1.fi>
CONFIG_VLAN_NETLINK=y build option can now be used to replace the
ioctl()-based interface for creating and removing VLAN interfaces
with netlink-based interface.
Signed-hostap: M. Braun <michael-dev@fami-braun.de>
If WNM is enabled for the build (CONFIG_WNM=y), add BSS max idle period
information to the (Re)Association Response frame from the AP and parse
this information on the station. For SME-in-wpa_supplicant case, add a
timer to handle periodic transmission of the keep-alive frame. The
actual request for the driver to transmit a frame is not yet
implemented.
Signed-hostap: Jouni Malinen <j@w1.fi>
This allows the internal TLS implementation to be built for TLS v1.2
support. In addition to the build option, this changes the TLS PRF
based on the negotiated version number. Though, this commit does not
yet complete support for TLS v1.2.
Signed-hostap: Jouni Malinen <j@w1.fi>
These protocols seem to be abandoned: latest IETF drafts have expired
years ago and it does not seem likely that EAP-TTLSv1 would be
deployed. The implementation in hostapd/wpa_supplicant was not complete
and not fully tested. In addition, the TLS/IA functionality was only
available when GnuTLS was used. Since GnuTLS removed this functionality
in 3.0.0, there is no available TLS/IA implementation in the latest
version of any supported TLS library.
Remove the EAP-TTLSv1 and TLS/IA implementation to clean up unwanted
complexity from hostapd and wpa_supplicant. In addition, this removes
any potential use of the GnuTLS extra library.
This can be used to avoid rejection of first two 4-way handshakes every
time hostapd (or wpa_supplicant in AP/IBSS mode) is restarted. A new
command line parameter, -e, can now be used to specify an entropy file
that will be used to maintain the needed state.
By default, make hostapd and wpa_supplicant maintain an internal
entropy pool that is fed with following information:
hostapd:
- Probe Request frames (timing, RSSI)
- Association events (timing)
- SNonce from Supplicants
wpa_supplicant:
- Scan results (timing, signal/noise)
- Association events (timing)
The internal pool is used to augment the random numbers generated
with the OS mechanism (os_get_random()). While the internal
implementation is not expected to be very strong due to limited
amount of generic (non-platform specific) information to feed the
pool, this may strengthen key derivation on some devices that are
not configured to provide strong random numbers through
os_get_random() (e.g., /dev/urandom on Linux/BSD).
This new mechanism is not supposed to replace proper OS provided
random number generation mechanism. The OS mechanism needs to be
initialized properly (e.g., hw random number generator,
maintaining entropy pool over reboots, etc.) for any of the
security assumptions to hold.
If the os_get_random() is known to provide strong ramdom data (e.g., on
Linux/BSD, the board in question is known to have reliable source of
random data from /dev/urandom), the internal hostapd random pool can be
disabled. This will save some in binary size and CPU use. However, this
should only be considered for builds that are known to be used on
devices that meet the requirements described above. The internal pool
is disabled by adding CONFIG_NO_RANDOM_POOL=y to the .config file.
Add comment about CONFIG_FULL_DYNAMIC_VLAN to defconfig. By default
this feature is still disabled.
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
The Prism54.org project seems have been dead for a while and it does not
look like this driver would ever be maintained again. Furthermore, it is
difficult to find a version that would work with the driver_prism54.c
wrapper and there is another driver for these card in the Linux kernel
tree.
The hostapd integration in driver_prism54.c is quite different from the
other driver wrappers and would require major effort to get it cleaned
up. Since there does not seem to be any real users for the cleaned up
version, there does not seem to be justification to spend this effort on
the wrapper. This old code is making it much more difficult to clean up
the driver interface and at this point, the best option seems to be to
remove the driver wrappers. Should someone really still need this, the
old code will continue to be available in hostapd 0.6.x.
This removes the hardcoded definition from Makefile and cleans up
source code by moving the mail HOSTAPD_DUMP_STATE blocks into separate
files to avoid conditional compilation within files.
MadWifi is unlikely to be in ../head relative to hostapd or
wpa_supplicant, as it would be inside the hostap git repository.
MadWifi sources are more likely to be in a directory called "madwifi"
and residing outside the hostap repository. Using "madwifi" also
demonstrates that the top-level madwifi directory is needed.
This adds WPS support for both hostapd and wpa_supplicant. Both programs
can be configured to act as WPS Enrollee and Registrar. Both PBC and PIN
methods are supported.
Currently, hostapd has more complete configuration option for WPS
parameters and wpa_supplicant configuration style will likely change in
the future. External Registrars are not yet supported in hostapd or
wpa_supplicant. While wpa_supplicant has initial support for acting as
an Registrar to configure an AP, this is still using number of hardcoded
parameters which will need to be made configurable for proper operation.
