This allows the internal TLS implementation to be built for TLS v1.2
support. In addition to the build option, this changes the TLS PRF
based on the negotiated version number. Though, this commit does not
yet complete support for TLS v1.2.
Signed-hostap: Jouni Malinen <j@w1.fi>
Prepare for multiple TLS PRF functions by renaming the SHA1+MD5 based
TLS PRF function to more specific name and add tls_prf() within the
internal TLS implementation as a wrapper for this for now.
Signed-hostap: Jouni Malinen <j@w1.fi>
IW_ENCODE_ALG_PMK and IW_ENC_CAPA_4WAY_HANDSHAKE are not defined in the
Android tree, so add compatibility defines for these.
Signed-hostap: Jouni Malinen <j@w1.fi>
Send the connection events from P2P group to both the group interface
and parent interface ctrl_ifaces to make it easier for external monitor
programs to see these events without having to listen to all group
interfaces when virtual group interfaces are used.
Signed-off-by: Dmitry Shmidt <dimitrysh@google.com>
The previous implementation was trying to add the first SSID
to a zero-length array. Avoid this with an explicit validation
of the array length.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
cfg80211 will reject the NL80211_CMD_START_SCHED_SCAN if too many
match sets are requested. To avoid being completely unable to start
any scheduled scans, skip setting these filters if the driver did
not advertise support for large enough number of match sets.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
This adds initial implementation of set_p2p_powersave to allow legacy PS
mode to be configured. P2P PS parameters are not yet supported.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
This cleans up the source code and makes it less likely that new AKM
addition misses some needed changes in the future.
Signed-hostap: Jouni Malinen <j@w1.fi>
wpa_supplicant is going to reject a configuration file that uses
WPA/WPA2-Personal (the default key_mgmt), but does not define
passphrase/PSK. Refuse to save such a configuration to avoid getting
stuck with a configuration that wpa_supplicant will reject.
Signed-hostap: Jouni Malinen <j@w1.fi>
This is the default value if device_type is not set, so do not
write it to the wpa_supplicant configuration file when saving
updated configuration.
Signed-hostap: Jouni Malinen <j@w1.fi>
If the station is indicating use of WPS, WSC IE should be added into the
(Re)Association Response frame. This is clear for the case when WSC IE
was included in the (Re)Association Request frame. However, even the
WLAN_STA_MAYBE_WPS case may actually indicate use of WPS. Assume that to
be the case when WPA/WPA2 is enabled (i.e., when the STA does not
include WPA/RSN/WSC IE while AP has WPA/RSN enabled).
Signed-hostap: Jouni Malinen <j@w1.fi>
This makes it clearer that the PMKSA caching entry gets removed from
the driver regardless of how the internal entry from wpa_supplicant
gets cleared. In practice, this call was skipped only for the case
when the entry for the current AP was being updated, so the previous
version was likely to work with all drivers. Anyway, it is cleaner
to explicitly remove the old entry even in that case before the new
entry gets added.
Signed-hostap: Jouni Malinen <j@w1.fi>
Commit 940a0ce970 moved the STA associated
check from driver_*.c into ieee802_1x_receive(), but failed to take into
account that wired networks and driver_wired.c do not mark the STA entry
associated. Fix this by skipping the check if the driver wrapper is
using a wired network.
Signed-hostap: Jouni Malinen <j@w1.fi>
Display signal strength in dBm with visual indicator in the form of a
bar for scan results displayed by wpa_gui-qt4. Any signal > -35dBm is
treated as full signal bar, signals between range of -95<->-35dBm are
displayed linearly. Convert WEXT signal level value to scale that
nl80211 typically reports in dBm. The condition which differentiates
8-bit WEXT dBm and regular dBm is probably fragile, but there is
currently no way to know what the driver is going to report for signal
strength.
Signed-off-by: Kel Modderman <kel@otaku42.de>
It's not really valid to send off-channel in all cases,
so pass whether it should be allowed or not and don't
set it in the AP case.
Also, to get the right ifindex for hostapd, pass a bss
pointer instead of the drv pointer.
Signed-hostap: Johannes Berg <johannes.berg@intel.com>
Use the no-ACK send_mlme request to transmit Probe Response frames
in P2P Listen state. This reduces number of unnecessary transmissions
if the peer device has already moved away from the channel. It will most
likely go through Search state multiple times anyway, so even if the
response were to be lost, a new retry will happen at higher layer.
Signed-hostap: Jouni Malinen <j@w1.fi>
Some client implementations only wait a few ms after sending a probe
request while scanning. Since probe responses are always sent at a low
rate this can eat quite some airtime and it might be impossible to get
the frame out before the client leaves the channel again. If the client
leaves before all probe reponses where acked this can cause the probe
reponse to be retried quite often consuming even more airtime.
Hence, add a new noack flag to the driver's send_mlme callback that
allows hostapd to request whether the driver should expect an ACK for
this frame or not.
Use the new noack-policy only for broadcast probe requests that contain
a wildcard SSID.
Signed-hostap: Helmut Schaa <helmut.schaa@googlemail.com>
In some situations it might be benefical to send a unicast frame without
the need for getting it ACKed (probe responses for example). In order to
achieve this add a new noack parameter to the drivers send_mlme callback
that can be used to advise the driver to not wait for an ACK for this
frame.
Signed-hostap: Helmut Schaa <helmut.schaa@googlemail.com>
Even though scan_ssid should not really be set for wildcard SSID,
better verify that here explicitly insead of assuming that the
SSID is set.
Signed-hostap: Jouni Malinen <j@w1.fi>
This structure was not really used for anything apart from figuring out
length of the EAP-pwd header (and even that in a way that would not work
with fragmentation). Since the bitfields in the structure could have
been problematic depending on target endianness, remove this unnecessary
structure.
Signed-hostap: Jouni Malinen <j@w1.fi>
Another niceness of OpenSSL is that if the high-order bit of a 521-bit
big num is not set then BN_bn2bin() will just return 65 bytes instead of
66 bytes with the 1st (big endian, after all) being all zero. When this
happens the wrong number of octets are mixed into function H(). So
there's a whole bunch of "offset" computations and BN_bn2bin() dumps the
big number into a buffer + offset. That should be obvious in the patch
too.
The previous EAP-pwd KDF implemented has an issue with group 21, that is
an elliptic curve group based on a 521 bit prime. 521 is not an even
multiple of 8, and therein lies the problem.
OpenSSL's BN library interprets a string of bits as in big-endian format
so all the calls of BN_bin2bn() will take the binary blob of bits and
turn it into a big number in big-endian format. In the EAP-pwd KDF, I am
stretching the key to "primebitlen". When that is not an even multiple
of 8 I have to mask off the excess. But I was masking off the excess
bits in the 1st octet (big endian after all) but that isn't right. The
KDF produces a string of endian-less bits. The 521st bit is the first
bit in the last octet, not the 7th bit in the first octet. So that has
been fixed and you can see in the attached diff what I'm doing.
If the kernel supports this, don't use manual null
data frame transmissions. This is one thing to get
rid of cooked monitor interfaces.
Signed-hostap: Johannes Berg <johannes.berg@intel.com>
The non-monitor TX currently uses a normal L2 abstraction
socket, but that will also receive frames we don't want,
so use a plain socket that isn't bound for RX. This might
be possible using the L2 abstraction, but we need a plain
socket later for getting TX status events here.
Signed-hostap: Johannes Berg <johannes.berg@intel.com>
This changes the auto-detection of whether or not the device contains
the AP SME away from monitor interface addition failing to the explicit
attribute in nl80211. Keep the old auto-detection for a little while so
that ath6kl isn't broken right away.
Signed-hostap: Johannes Berg <johannes.berg@intel.com>
The new event can be used when EAPOL TX status can't be reported as a
complete 802.11 frame but is instead reported as just the EAPOL data as
originally passed to hapd_send_eapol().
Signed-hostap: Johannes Berg <johannes.berg@intel.com>
Currently OpenSSL implementation of TLS in hostapd loads only top
certificate in server certificate file. Change this to try to the
whole chain first and only if that fails, revert to old behavior.
Signed-off-by: Maciej Szmigiero <mhej@o2.pl>
The source code compiles into different objects depending on
the contents of .config. Therefore, the objects should depend
on .config.
Previously, only the executables depended on .config. This meant
that they were re-linked when .config changed. But that relink
process used the old (and now wrong) objects.
