Increase EAPOL startWhen to 2 for the case where the AP/GO has
advertised it supports WPS 2.0. This is done to make it less likely for
the EAPOL-Start frame to be sent out since that is only required for WPS
1.0. Not sending it can remove one unnecessary round trip from the EAP
exchange when the AP is going to start with EAP-Request/Identity
immediately based on the Association Request frame.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Commit 152cff6ba6 ('P2P: Remove
WPA_DRIVER_FLAGS_P2P_MGMT option') removed the only non-zero return from
wpas_p2p_stop_find_oper(), but did not remove the useless return value
or the return check in wpas_p2p_stop_find(). Clean these up by removing
unreachable code and useless return value.
Signed-off-by: Eduardo Abinader <eduardo.abinader@openbossa.org>
This is needed for number of items and it was possible to make a build
configuration that did not include ieee802_11_common.c while still
trying to use functions from there. While it would be possible to add
NEED_80211_COMMON=y to all the cases where this file is needed, the
extra complexity from this is not really justifiable anymore, so include
the file unconditionally.
Signed-off-by: Jouni Malinen <j@w1.fi>
The MACsec addition placed one of the calls outside the #ifdef
IEEE802X_EAPOL block while the variable needed for this was defined only
within the block.
Signed-off-by: Jouni Malinen <j@w1.fi>
This information can be used to determine whether the event is generated
for a new peer that was added or due to an update in the information for
an existing peer.
Signed-off-by: Jouni Malinen <j@w1.fi>
The new openssl_cipher configuration parameter can be used to select
which TLS cipher suites are enabled for TLS-based EAP methods when
OpenSSL is used as the TLS library. This parameter can be used both as a
global parameter to set the default for all network blocks and as a
network block parameter to override the default for each network
profile.
Signed-off-by: Jouni Malinen <j@w1.fi>
Mark the variable as unsigned and make the length check use "len > end -
pos" version to makes this easier to understand for static analyzers
(CID 74155).
Signed-off-by: Jouni Malinen <j@w1.fi>
len + pos > end comparison here did verify that the length field had a
valid value, but that did not seem to enough to avoid TAINTED_SCALAR
warning. Re-order that validation step to be equivalent "len > end -
pos" to remove these false positives (CID 68116).
Signed-off-by: Jouni Malinen <j@w1.fi>
The driver_test.c driver wrapper (-Dtest in wpa_supplicant and
driver=test in hostapd) was previously used for testing without real
Wi-Fi hardware. mac80211_hwsim-based tests have practically replaced all
these needs and there has been no improvements or use for driver_test.c
in a long while. Because of this, there has not really been any effort
to maintain this older test tool and no justification to change this
either. Remove the obsoleted test mechanism to clean up the repository.
Signed-off-by: Jouni Malinen <j@w1.fi>
Previously, wpas_set_wowlan_triggers() could have been called in
uninitialized wpa_driver_capa data if the driver interface did not
support reporting of capabilities. While this would not really happen
with a driver wrapper that implements set_wowlan() and as such, would
not cause any difference in practice, it is better to clean this up to
make the code path easier to understand for static analyzers.
Signed-off-by: Jouni Malinen <j@w1.fi>
The new ext_eapol_frame_io parameter can be used to configure hostapd
and wpa_supplicant to use control interface for receiving and
transmitting EAPOL frames. This makes it easier to implement automated
test cases for protocol testing. This functionality is included only in
CONFIG_TESTING_OPTIONS=y builds.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
A P2P Client may be able to connect to the GO even if the WPS
provisioning step has not terminated cleanly (e.g., P2P Client does not
send WSC_Done). Such group formation attempt missed the event
notification about started group on the GO and also did not set the
internal state corresponding to the successful group formation.
This commit addresses the missing part by completing GO side group
formation on a successful first data connection if WPS does not complete
cleanly. Also, this commit reorders the STA authorization indications to
ensure that the group formation success notification is given prior to
the first STA connection to handle such scenarios.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Previously, this variable did not necessarily get cleared between group
formations and could result in some of the workaround operations from
not being executed after the first group formation when using the same
interface for all P2P groups. Fix this by clearing the variable whenever
starting the GO to make sure it is used consistently for each group
formation.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
It was possible for local deauthentication request to leave sme-connect
radio work running even when there was no ongoing effort to complete the
connection anymore. Clean this up by marking sme-connect radio work
item, if any, done when clearing connection state after such
disconnection during connection.
Signed-off-by: Jouni Malinen <j@w1.fi>
It was possible for group formation timeout to be the trigger for
detecting the second PSK/4-way handshake failure. If that happened, the
special reason=PSK_FAILURE was not used in the P2P-GROUP-REMOVED event
even though P2P-PERSISTENT-PSK-FAIL did get reported. Fix this special
case by replacing the reason code with PSK_FAILURE if the PSK failure
timeout gets registed as part of the disconnection processing in the
formation timeout handler.
Signed-off-by: Jouni Malinen <j@w1.fi>
Use os_exec() to run the action script operations to avoid undesired
command line processing for control interface event strings. Previously,
it could have been possible for some of the event strings to include
unsanitized data which is not suitable for system() use. (CVE-2014-3686)
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Commit 86bd36f0d5 ("Add generic
mechanism for adding vendor elements into frames") has a minor bug
where it miscalculates the length of memory to move using
os_memmove. If multiple vendor elements are specified then this can
lead to out of bounds memory accesses.
This patch fixes this by calculating the correct length of remaining
data to shift down in the information element.
Signed-off-by: Toby Gray <toby.gray@realvnc.com>
Use hostapd_freq_params instead of simple frequency parameter for driver
commands. This is preparation for IBSS configuration to allow use of
HT/VHT in IBSS.
Signed-off-by: Janusz Dziedzic <janusz.dziedzic@tieto.com>
Previously, the case of non-netdev P2P management device ended up
pulling in both the main interface (e.g., wlan0) and P2P Device
interface (from command line -m argument) as configuration. Similarly,
the main interface ended up included both configuration files. This is
not really helpful for various use cases, e.g., when permanent P2P group
information is stored in the P2P Devince interface, but it gets
duplicated in the main station interface configuration.
Clean this up by changing the -m<file> argument to replace, not
concatenate, configuration information. In other words, the main station
interface will not read this configuration and the P2P Device interface
(non-netdev) does not read parameters from the station interface
configuration file.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Relying on qos qosinfo is not enough, as it can be 0 for WMM enabled
peers that don't support U-APSD. Further, some peers don't even contain
this IE (Google Nexus 5), but do contain the WMM IE during setup.
Signed-off-by: Arik Nemtsov <arikx.nemtsov@intel.com>
Some drivers need to know the initiator of a TDLS connection in order
to generate a correct TDLS mgmt packet. It is used to determine
the link identifier IE. Pass this information to the driver.
Signed-off-by: Arik Nemtsov <arikx.nemtsov@intel.com>
mac_addr=2 and preassoc_mac_addr=2 parameters can now be used to
configure random MAC address to be generated by maintaining the OUI part
of the permanent MAC address (but with locally administered bit set to
1). Other than that, these values result in similar behavior with
mac_addr=1 and preassoc_mac_addr=1, respectively.
Signed-off-by: Jouni Malinen <j@w1.fi>
Support 60 GHz band in P2P module by selecting random social channel
from all supported social channels in 2.4 GHz and 60 GHz bands.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This permits to set or unset the WiFi Display subelements from DBus, by
providing the full WFD specific IE frame.
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
If "STA_AUTOCONNECT 0" has been used to disable automatic connection on
disconnection event and the driver indicates multiple disconnection
events for the disconnection from the current AP when WPS is started, it
could have been possible to hit a case where wpa_s->disconnected was set
to 1 during WPS processing and the following scan result processing
would stop the operation.
wpa_s->key_mgmt == WPA_KEY_MGMT_WPS check was trying to avoid to skip
autoconnect when WPS was in use, but that does not seem to work anymore.
Fix this by checking through wpas_wps_searching() as well to avoid
setting wpa_s->disconnect = 1 when there is an ongoing WPS operation.
Signed-off-by: Jouni Malinen <j@w1.fi>
This check is already being done on wpas_p2p_deinit_iface.
Of course, it is assumed wpa_s is not deinit when reaches
that point as a matter of fact.
Signed-off-by: Eduardo Abinader <eduardo.abinader@openbossa.org>
As P2P service are not necessarily attached to a iface, when
added, proceed with same approach on p2p global deinit. Such
approach solves memory leaks ocurring upon wpa_supplicant
termination, when p2p services were registered previously.
Signed-off-by: Eduardo Abinader <eduardo.abinader@openbossa.org>
This adds experimental support for wpa_supplicant to assign random local
MAC addresses for both pre-association cases (scan, GAS/ANQP) and for
connections. MAC address policy for each part can be controlled
separately and the connection part can be set per network block.
This requires support from the driver to allow local MAC address to be
changed if random address policy is enabled. It should also be noted
that number of drivers would not support concurrent operations (e.g.,
P2P and station association) with random addresses in use for one or
both.
This functionality can be controlled with the global configuration
parameters mac_addr and preassoc_mac_addr which set the default MAC
address policies for connections and pre-association operations (scan
and GAS/ANQP while not connected). The global rand_addr_lifetime
parameter can be used to set the lifetime of a random MAC address in
seconds (default: 60 seconds). This is used to avoid unnecessarily
frequent MAC address changes since those are likely to result in driver
clearing most of its state. It should be noted that the random MAC
address does not expire during an ESS connection, i.e., this lifetime is
only for the case where the device is disconnected.
The mac_addr parameter can also be set in the network blocks to define
different behavior per network. For example, the global mac_addr=1 and
preassoc_mac_addr=1 settings and mac_addr=0 in a home network profile
would result in behavior where all scanning is performed using a random
MAC address while connections to new networks (e.g.,
Interworking/Hotspot 2.0) would use random address and connections to
the home network would use the permanent MAC address.
Signed-off-by: Jouni Malinen <j@w1.fi>
This extends "wpa_cli -a<action script>" functionality to work with the
global wpa_supplicant control interface. The IFNAME=<ifname> prefix is
removed from the event messages and converted to the control interface
name when present. Previously, action scripts could only be used with
the per-interface control interfaces.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Number of other buffers were already increased to this size, but the
buffer used for receiving unsolicited event messages from wpa_supplicant
(e.g., for wpa_cli action scripts) was still at the older 256 byte size.
This could result in some events getting truncated. Avoid this by using
the same 4096 byte buffer size here as in the other places receiving
messages from wpa_supplicant.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
The ifname_prefix string could change during line editing and the
periodic PING command running in the background ended up getting the
latest snapshot of the command line due to the pointer being left to
point to the edit buffer. This resulted in unexpected prefix strings
getting used with the periodic PING command. Fix this by temporarily
clearing the ifname_prefix whenever running such a periodic PING.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
The commit 5cd4740580 has rearranged the
update scan results code and hence the IEs were not getting updated
properly for ap_scan=1 case. This can result in a 4-way handshake
failure in the roaming case (IE mismatch in 3/4 EAPOL). Fix this by
updating the scan results even if ap_scan=1 is used and network does not
need to get reselected based on association information.
Signed-off-by: Jithu Jance <jithu@broadcom.com>
Signed-off-by: Dmitry Shmidt <dimitrysh@google.com>
Signed-off-by: Jouni Malinen <j@w1.fi>
It also allows to use the STATUS command with default behavior,
say for debug, i.e., don't generate a "fake" CONNECTION and
SUPPLICANT_STATE_CHANGE events with the new STATUS-NO_EVENTS case.
Signed-off-by: Dmitry Shmidt <dimitrysh@google.com>
In theory, this call could fail, so check the return value before using
the received data. These specific cases would not really care much about
the failures, but this keeps the code more consistent and keeps static
analyzer warnings more useful. (CID 72678, CID 72679, CID 72680,
CID 72683, CID 72689, CID 72698, CID 72703)
Signed-off-by: Jouni Malinen <j@w1.fi>
The network block bssid parameter can be used to force a specific BSS to
be used for a connection. It is also possible to modify this parameter
during an association. Previously, that did not result in any
notification to the driver which was somewhat problematic with drivers
that take care of BSS selection. Add a new mechanism to allow
wpa_supplicant to provide a driver update if the bssid parameter change
for the current connection modifies roaming policy (roaming
allowed/disallowed within ESS).
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
An interoperability issue with a deployed AP has been identified where
the connection fails due to that AP failing to operate correctly if
PMKID is included in the Association Request frame. To work around this,
allow EAPOL-Start packet to be transmitted on startWhen reaching 0 even
when trying to use PMKSA caching. In practice, this allows fallback to
full EAP authentication if the AP/Authenticator takes more than 1-2
seconds to initiate 4-way handshake for PMKSA caching or full EAP
authentication if there was no PMKSA cache match.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Previously, the shorter startWhen value was used based on build
parameters (i.e., if WPS was enabled). This is not really ideal and the
knowledge of WPS use can be provided to the EAPOL state machine to allow
this (and similar WPS workarounds) to be done only when the association
is for the purpose of WPS.
Reduce the default startWhen value from 3 to 2 seconds for non-WPS case
since WPS builds have likely received most testing for the past years
with the 1 second value and there is no strong justification for forcing
the longer 3 second wait should a frame be lost or something else
require the EAPOL-Start to initiate operation after a connection.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
