Commit graph

586 commits

Author SHA1 Message Date
Avraham Stern
76196ddb2b wpa_supplicant: Add support for Beacon Report Radio Measurement
Beacon Report Radio Measurement is defined in IEEE Std 802.11-2016,
11.11.9.1. Beacon Report is implemented by triggering a scan on the
requested channels with the requested parameters.

Signed-off-by: Avraham Stern <avraham.stern@intel.com>
2017-01-03 15:18:30 +02:00
Avraham Stern
ec493469f6 wpa_supplicant: Move RRM implementation to a dedicated file
As support for new RRM measurements will be added, the RRM
implementation will become quite large, so move it to a dedicated file.

Signed-off-by: Avraham Stern <avraham.stern@intel.com>
2017-01-03 15:18:29 +02:00
Jouni Malinen
6a31440b86 Fix LCI request subelement processing
Commit 4a742011ab ('wpa_supplicant: Handle
LCI request') introduced LCI request parsing in a manner that
incremented the request pointer by four within
wpas_rrm_build_lci_report() without decrementing len correspondingly.
This could potentially result in get_ie() reading four octets beyond the
buffer if a corrupted request is received. This would be applicable only
if the LCI reporting was enabled explicitly ("SET LCI ..." control
interface command).

Fix this by updating the len variable to match the request pointer
changes.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2017-01-03 15:18:29 +02:00
vamsi krishna
065c029a55 Remove MBO dependency from Supported Operating Classes element
Supported Operating Classes element and its use is define in the IEEE
802.11 standard and can be sent even when MBO is disabled in the build.
As such, move this functionality out from the CONFIG_MBO=y only mbo.c.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2016-12-11 22:07:58 +02:00
Jouni Malinen
a1836de64b SME: Fix IBSS setup after shared key/FT/FILS association
wpa_s->sme.auth_alg could have been left to a previously value other
than WPA_AUTH_ALG_OPEN if IBSS network is used after an association that
used shared key, FT, or FILS authentication algorithm. This could result
in the IBSS setup failing due to incorrect authentication processing
steps.

Fix this by setting wpa_s->sme.auth_alg = WPA_AUTH_ALG_OPEN whenever
starting an IBSS (or mesh, for that matter) network.

Signed-off-by: Jouni Malinen <j@w1.fi>
2016-12-11 18:23:13 +02:00
Sabrina Dubroca
ad51731abf wpa_supplicant: Allow pre-shared (CAK,CKN) pair for MKA
This enables configuring key_mgmt=NONE + mka_ckn + mka_cak.
This allows wpa_supplicant to work in a peer-to-peer mode, where peers
are authenticated by the pre-shared (CAK,CKN) pair. In this mode, peers
can act as key server to distribute keys for the MACsec instances.

This is what some MACsec switches support, and even without HW
support, it's a convenient way to setup a network.

Signed-off-by: Sabrina Dubroca <sd@queasysnail.net>
2016-11-20 00:35:08 +02:00
Jouni Malinen
81a10a9442 Do not try to start/join RSN IBSS without CONFIG_IBSS_RSN=y
Previously, a build without IBSS RSN support tried to start/join an IBSS
even if the profile was configured with RSN parameters. This does not
work and resulted in quite confusing debug log. Make this clearer by
explicitly checking for this case and reject the connection attempt with
a clearer debug log entry instead of trying something that is known to
fail.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2016-10-28 19:33:20 +03:00
Benjamin Richter
5d30f927ea wpa_supplicant: Restore permanent MAC address on reassociation
With mac_addr=0 and preassoc_mac_addr=1, the permanent MAC address
should be restored for association. Previously this did not happen when
reassociating to the same ESS.

Signed-off-by: Benjamin Richter <br@waldteufel.eu>
2016-10-16 11:44:34 +03:00
Jouni Malinen
4b5b8a53a1 WPS: Force BSSID for WPS provisioning step connection
This was already done for most driver cases, but it is possible that the
BSSID/frequency is not forced if the driver reports BSS selection
capability (e.g., NL80211_ATTR_ROAM_SUPPORT). That could potentially
result in the driver ignoring the BSSID/frequency hint and associating
with another (incorrect) AP for the WPS provisioning step if that
another AP in the same ESS is more preferred (e.g., better signal
strength) by the driver and only one of the APs (the not preferred one)
is in active WPS registrar state.

While most drivers follow the BSSID hint for the initial connection to
an ESS, not doing it here for the WPS provisioning would break the
protocol. Fix this by enforcing a single BSSID/frequency to disallow the
driver from selecting an incorrect AP for the WPS provisioning
association.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2016-10-11 00:25:20 +03:00
Jouni Malinen
b8ae56e4d0 FILS: Allow wpa_supplicant to select FILS AKM for connection
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2016-10-10 21:11:46 +03:00
Jouni Malinen
e4d2ce1b52 FILS: Set FILS Capability bit in management frames from station
If FILS is supported, indicate that in Probe Request and (Re)Association
Request frames in the Extended Capabilities element.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2016-10-10 21:11:46 +03:00
Max Stepanov
be7ebd892e wpa_supplicant: Cancel sched_scan on SELECT_NETWORK initiated scan
If a scheduled scan is running on select network command,
cancel and reset it before kicking off a regular scan request.

Signed-off-by: Max Stepanov <Max.Stepanov@intel.com>
2016-09-27 00:02:44 +03:00
Mikael Kanstrup
02adead53e Add ignore_auth_resp control interface debug parameter
Implement "SET ignore_auth_resp <0/1>" command to simulate auth/assoc
response loss and EAPOL RX packet loss by ignoring corresponding
incoming events.

Signed-off-by: Mikael Kanstrup <mikael.kanstrup@sonymobile.com>
2016-09-23 17:36:55 +03:00
Mikael Kanstrup
04e3d8156a Blacklist correct BSSID on authentication timeout
If authentication times out while reassociating to same ESS incorrect
BSSID may end up being blacklisted. Use pending_bssid field on
authentication timeout and deauthentication to ensure the correct AP
gets blacklisted. This is mainly to address cases related to Android
framework roaming behavior.

Signed-off-by: Mikael Kanstrup <mikael.kanstrup@sonymobile.com>
2016-09-23 17:36:55 +03:00
Lior David
d1723c5566 wpa_supplicant: Allow FTM functionality to be published
Add configuration options that control publishing of fine timing
measurement (FTM) responder and initiator functionality via bits 70, 71
of Extended Capabilities element. Typically, FTM functionality is
controlled by a location framework outside wpa_supplicant. When
framework is activated, it will use wpa_supplicant to configure the
STA/AP to publish the FTM functionality. See IEEE P802.11-REVmc/D7.0,
9.4.2.27.

Signed-off-by: Lior David <qca_liord@qca.qualcomm.com>
2016-09-05 21:27:23 +03:00
Roshan Pius
d015bb05df Move network add/remove operations to a common function
All the 3 control interfaces: socket based, dbus & binder needs to
perform the same sequence of steps for network add/remove. So, move
these to a common utility method in |wpa_supplicant.c| instead of
duplicating the code everywhere.

Signed-off-by: Roshan Pius <rpius@google.com>
2016-08-18 20:46:18 +03:00
Masashi Honma
ecba4509d9 mesh: Simplify HT40 check code
The ht40 variable can only have values -1 or 1 here, so need to try to
address ht40 == 0 case.

Signed-off-by: Masashi Honma <masashi.honma@gmail.com>
2016-08-18 10:46:39 +03:00
Masashi Honma
05aed438cd mesh: Set correct secondary channel offset if HT40 is disabled
Previously, secondary channel offset could be non zero even though
disable_ht40=1. This patch fixes it.

Signed-off-by: Masashi Honma <masashi.honma@gmail.com>
2016-08-18 10:43:19 +03:00
Roshan Pius
5f040be4ff Move disconnect command handling to a common place
Move out the disconnect command handling from |ctrl_iface.c| to
|wpa_supplicant.c| so that it can be reused across the different
control interfaces (socket, dbus & binder).

Signed-off-by: Roshan Pius <rpius@google.com>
2016-08-13 21:11:04 +03:00
vamsi krishna
cc9985d1b1 Set default scan IEs to the driver (QCA vendor extension)
This makes wpa_supplicant set default scan IEs to the driver (if the
vendor command is supported). The driver can use these IEs in the scan
requests initiated by the driver itself. Also the driver can merge these
IEs into further scan requests that it receives, in case if the scan
request doesn't carry any of the IEs sent in this command.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2016-08-02 21:21:52 +03:00
Masashi Honma
3388e7b96f mesh: Remove HT IEs if HT is disabled
Previously, HT capability IE and HT information IE were included in
Beacon and Mesh Peering Open/Confirm frames even if HT is disabled with
disable_ht=1. This patch removes these.

Signed-off-by: Masashi Honma <masashi.honma@gmail.com>
2016-07-23 22:04:16 +03:00
Jouni Malinen
4d8d710f0b Fix byte order for CONFIG_VHT_OVERRIDES parameters
The VHT parameters were not swapped properly on big endian systems.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2016-06-23 13:41:18 +03:00
Jouni Malinen
39cdd3a0f9 FST: Mark wpa_supplicant callback functions get_peer_{first,next} static
These are used only through function pointers, so no need to keep the
functions non-static.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2016-06-23 13:32:29 +03:00
Jouni Malinen
331f07742f mesh: Allow 160 MHz channel to be configured
This allows minimal testing with 160 MHz channel with country code ZA
that happens to be the only one with a non-DFS 160 MHz frequency. DFS
with mesh is not yet supported.

Signed-off-by: Jouni Malinen <j@w1.fi>
2016-06-04 21:30:51 +03:00
Kanchanapally, Vidyullatha
cc9a2575ca nl80211: Use extended capabilities per interface type
This adds the necessary changes to support extraction and use of the
extended capabilities specified per interface type (a recent
cfg80211/nl80211 extension). If that information is available,
per-interface values will be used to override the global per-radio
value.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2016-05-31 21:35:54 +03:00
Jouni Malinen
22950049e4 Ignore pmf=1/2 parameter for non-RSN networks
PMF is available only with RSN and pmf=2 could have prevented open
network connections. Change the global wpa_supplicant pmf parameter to
be interpreted as applying only to RSN cases to allow it to be used with
open networks.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2016-05-05 21:09:08 +03:00
David Spinadel
4a742011ab wpa_supplicant: Handle LCI request
Handle radio measurement request that contains LCI request. Send
measurement report based on a configurable LCI report element. The LCI
report element is configured over the control interface with

SET lci <hexdump of the element>

and cleared with

SET lci ""

Signed-off-by: David Spinadel <david.spinadel@intel.com>
2016-04-17 12:29:12 +03:00
David Spinadel
d41a5352fe wpa_supplicant: Add LCI and civic request to Neighbor Report Request
Add an option to request LCI and Location Civic Measurement in Neighbor
Report Request frame, as described in IEEE P802.11-REVmc/D5.0, 9.6.7.6.

Note: This changes the encoding format of the NEIGHBOR_REP_REQUEST
ssid=<val> parameter. This used to be parsed as raw SSID data which is
problematic for accepting additional parameters. The new encoding allows
either a string within double-quotation marks or a hexdump of the raw
SSID.

Thew new format:
NEIGHBOR_REP_REQUEST [ssid=<SSID>] [lci] [civic]

Signed-off-by: David Spinadel <david.spinadel@intel.com>
2016-04-16 21:05:39 +03:00
Matti Gottlieb
ece4ac5f4e HS 2.0: Add support for configuring frame filters
When a station starts an association to a Hotspot 2.0 network, request
the driver to do the following, based on the BSS capabilities:

1. Enable gratuitous ARP filtering
2. Enable unsolicited Neighbor Advertisement filtering
3. Enable unicast IP packet encrypted with GTK filtering if
   DGAF disabled bit is zero

Clear the filter configuration when the station interface is
disassociated.

Signed-off-by: Matti Gottlieb <matti.gottlieb@intel.com>
2016-04-08 15:21:18 +03:00
Lior David
90f14962ec wpa_supplicant: "don't care" value for pbss in ssid structure
Add a new value 2 to the pbss parameter of wpa_ssid structure, which
means "don't care". This value is used in infrastructure mode to request
connection to either AP or PCP, whichever is available in the scan
results. The value is also used in regular WPS (not P2P group formation)
to make WPS work with devices running as either AP or PCP.

Signed-off-by: Lior David <qca_liord@qca.qualcomm.com>
2016-04-08 12:56:34 +03:00
Jouni Malinen
6a5ee810a3 Include previous BSSID in connection request to indicate reassociation
This allows the SME-in-the-driver case to get similar information about
reassociation that was already available for the SME-in-wpa_supplicant
case.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2016-03-24 22:35:10 +02:00
Roy Marples
2e997eece5 Add interface matching support with -M, guarded by CONFIG_MATCH_IFACE
The new wpa_supplicant command line argument -M can be used to describe
matching rules with a wildcard interface name (e.g., "wlan*").

This is very useful for systems without udev (Linux) or devd (FreeBSD).

Signed-off-by: Roy Marples <roy@marples.name>
2016-03-22 17:41:37 +02:00
Roy Marples
45e3fc72c6 Find correct driver for interface additions/removals
Interface additions/removals are not guaranteed to be for the driver
listening to the kernel events. As such, send the events to
wpa_supplicant_event_global() which can then pick the correct interface
registered with wpa_supplicant to send the event to.

Signed-off-by: Roy Marples <roy@marples.name>
2016-03-22 17:41:37 +02:00
Lior David
2b6e9f91df wpa_supplicant: Expose wpas_get_bands() and related API
Expose the functions wpas_get_bands() and wpas_freq_to_band() and the
enum wpa_radio_work_band, since they will be needed outside
wpa_supplicant.c.

Signed-off-by: Lior David <qca_liord@qca.qualcomm.com>
2016-03-03 15:10:50 +02:00
Lior David
96a26ab744 P2P: Support dedicated P2P_DEVICE without separate group interface
Add support for drivers with dedicated P2P_DEVICE interface, but without
group interface concurrency (only a single netdev is used). With such
devices, wpa_supplicant tried to use the p2p_dev interface instead of
the group interface and most P2P operations failed. Extend
wpa_supplicant to use the primary interface instead of a separate group
interface in such cases.

Signed-off-by: Lior David <qca_liord@qca.qualcomm.com>
2016-02-27 19:37:19 +02:00
Lior David
ba307f8528 P2P: Add a separate pointer to the P2P Device instance
In many places in the code there was a reference to wpa_s->parent to get
from group interface to p2p_dev interface. These places can break if
P2P_DEVICE interface would need to be used with the primary interface as
the group interface, since the parent of the primary interface points to
itself and not the p2p_dev interface.

Fix this by adding a separate "p2pdev" pointer to wpa_supplicant,
it will be the same as parent pointer in most cases but whenever
the primary interface is used as a group interface, change it to
point to the correct p2p_dev interface.

Signed-off-by: Lior David <qca_liord@qca.qualcomm.com>
2016-02-27 19:37:19 +02:00
Jouni Malinen
d010048cf7 MBO: Expire non-matching bss_tmp_disallowed entries as part of check
This makes wpa_is_bss_tmp_disallowed() expire old entries from the
bss_tmp_disallowed list even if they do not match the BSSID that is
being searched for. This allows the list to be kept at shorter length to
speed up operations and minimize memory use in cases where the
previously disabled BSS is not in radio range anymore.

Signed-off-by: Jouni Malinen <j@w1.fi>
2016-02-22 19:53:04 +02:00
Avraham Stern
c484b19882 Move Hotspot 2.0 element in (Re)Association Request frames
According to IEEE Std 802.11-2012, Table 8-22, vendor specific elements
must follow all other elements, so Hotspot 2.0 element which is actually
a vendor specific element must come after all other elements.

Signed-off-by: Avraham Stern <avraham.stern@intel.com>
2016-02-22 19:53:04 +02:00
Avraham Stern
dd5999084e MBO: Parse MBO IE in BSS Transition Management Request frames
Add parsing of MBO IE in BSS Transition Management Request frames. If
the MBO IE includes the association retry delay attribute, do not try to
reconnect to the current BSS until the delay time is over.

If the MBO IE includes the cellular data connection preference attribute
or the transition rejection reason attribute, send a message to upper
layers with the data.

Signed-off-by: David Spinadel <david.spinadel@intel.com>
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
2016-02-22 19:53:04 +02:00
Avraham Stern
5e57ba2505 MBO: Add Supported Operating Classes element to Association Request
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
2016-02-22 19:53:04 +02:00
David Spinadel
92c6e2e3a9 MBO: Implement MBO non-preferred channel report in Association Request
Add MBO IE with non-preferred channels to (Re)Association Request
frames.

Signed-off-by: David Spinadel <david.spinadel@intel.com>
2016-02-22 19:53:04 +02:00
Avraham Stern
ea69d9737c wpa_supplicant: Share a single get_mode() implementation
There is no need to duplicate this helper function in multiple files.

Signed-off-by: Avraham Stern <avraham.stern@intel.com>
2016-02-21 17:14:51 +02:00
Masashi Honma
70c93963ed SAE: Fix PMKID calculation for PMKSA cache
The SAE PMKID is calculated with IEEE Std 802.11-2012 11.3.5.4, but the
PMKID was re-calculated with 11.6.1.3 and saved into PMKSA cache. Fix
this to save the PMKID calculated with 11.3.5.4 into the PMKSA cache.

Signed-off-by: Masashi Honma <masashi.honma@gmail.com>
2016-02-18 21:07:47 +02:00
Lior David
b907491281 wpa_supplicant: Basic support for PBSS/PCP
PBSS (Personal Basic Service Set) is a new BSS type for DMG
networks. It is similar to infrastructure BSS, having an AP-like
entity called PCP (PBSS Control Point), but it has few differences.
PBSS support is mandatory for IEEE 802.11ad devices.

Add a new "pbss" argument to network block. The argument is used
in the following scenarios:
1. When network has mode=2 (AP), when pbss flag is set will start
as a PCP instead of an AP.
2. When network has mode=0 (station), when pbss flag is set will
connect to PCP instead of AP.

The function wpa_scan_res_match() was modified to match BSS according to
the pbss flag in the network block (wpa_ssid structure). When pbss flag
is set it will match only PCPs, and when it is clear it will match only
APs.

Signed-off-by: Lior David <qca_liord@qca.qualcomm.com>
2016-02-08 22:23:56 +02:00
Roy Marples
2e69bdd16a eloop: Add eloop_sock_requeue()
This function can be used to re-build eloop socket tables after forking
for eloop implementations that need this.

Signed-off-by: Roy Marples <roy@marples.name>
2016-02-07 12:38:04 +02:00
Jouni Malinen
6174de663c mesh: Connection and group started/removed events into debug log
The messages were sent out with wpa_msg_ctrl() so they were not visible
in the debug log. However, these would be quite helpful strings to
search for in the debug log, so change these messages to use wpa_msg().

Signed-off-by: Jouni Malinen <j@w1.fi>
2016-01-06 13:13:13 +02:00
Jouni Malinen
15c5606758 Update copyright notices for the new year 2016
Signed-off-by: Jouni Malinen <j@w1.fi>
2016-01-01 13:42:04 +02:00
Ilan Peer
ede7770180 wpa_supplicant: Do not wait for monitor on P2P Device interface
External programs are not aware of the creation of a
dedicated P2P Device interface, so it does not make sense
to wait for a monitor to connect on such an interface.

Fix this by not waiting on a dedicated P2P Device interface
for monitor to attach.

Signed-off-by: Ilan Peer <ilan.peer@intel.com>
2015-12-28 17:21:08 +02:00
Jouni Malinen
e7160bd8fe Drop any pending EAPOL RX frame when starting a new connection
Such a pending frame cannot be valid anymore, so drop it instead of
risking of using an unexpected EAPOL frame after association if a
previous association received one at the end and the new association can
happen within 100 ms.

Signed-off-by: Jouni Malinen <j@w1.fi>
2015-12-20 17:25:41 +02:00
Jouni Malinen
ca9968a012 HS 2.0: Convert icon storage to use dl_list
This simplifies the list operations quite a bit.

Signed-off-by: Jouni Malinen <j@w1.fi>
2015-12-19 18:49:57 +02:00
Jouni Malinen
3c108b7573 EAP peer: External server certificate chain validation
This adds support for optional functionality to validate server
certificate chain in TLS-based EAP methods in an external program.
wpa_supplicant control interface is used to indicate when such
validation is needed and what the result of the external validation is.

This external validation can extend or replace the internal validation.
When ca_cert or ca_path parameter is set, the internal validation is
used. If these parameters are omitted, only the external validation is
used. It needs to be understood that leaving those parameters out will
disable most of the validation steps done with the TLS library and that
configuration is not really recommend.

By default, the external validation is not used. It can be enabled by
addingtls_ext_cert_check=1 into the network profile phase1 parameter.
When enabled, external validation is required through the CTRL-REQ/RSP
mechanism similarly to other EAP authentication parameters through the
control interface.

The request to perform external validation is indicated by the following
event:
CTRL-REQ-EXT_CERT_CHECK-<id>:External server certificate validation needed for SSID <ssid>

Before that event, the server certificate chain is provided with the
CTRL-EVENT-EAP-PEER-CERT events that include the cert=<hexdump>
parameter. depth=# indicates which certificate is in question (0 for the
server certificate, 1 for its issues, and so on).

The result of the external validation is provided with the following
command:
CTRL-RSP-EXT_CERT_CHECK-<id>:<good|bad>

It should be noted that this is currently enabled only for OpenSSL (and
BoringSSL/LibreSSL). Due to the constraints in the library API, the
validation result from external processing cannot be reported cleanly
with TLS alert. In other words, if the external validation reject the
server certificate chain, the pending TLS handshake is terminated
without sending more messages to the server.

Signed-off-by: Jouni Malinen <j@w1.fi>
2015-12-12 18:24:27 +02:00
Avichal Agarwal
af041f997d dbus: Add support for vendor specific elements
The new methods are
1. VendorElemAdd "i" "ay" i=integer ay=array of bytes
2. VendorElemGet "i" i=integer (output array of bytes)
3. VendorElemRem "i" "ay" i=integer ay=array of bytes

These provide functionality similar to the control interface commands
VENDOR_ELEM_ADD, VENDOR_ELEM_GET, and VENDOR_ELEM_REMOVE.

Signed-off-by: Avichal Agarwal <avichal.a@samsung.com>
Signed-off-by: Purushottam Kushwaha <p.kushwaha@samsung.com>
Signed-off-by: Kyeong-Chae Lim <kcya.lim@samsung.com>
Signed-off-by: Mayank Haarit <mayank.h@samsung.com>
Signed-off-by: Dilshad Ahmad <dilshad.a@samsung.com>
[VendorElemGet to return array of bytes instead of string; cleanup]
Signed-off-by: Jouni Malinen <j@w1.fi>
2015-12-06 12:50:13 +02:00
Jouni Malinen
bea48f7784 Allow sched_scan_plans to be updated at runtime
This allows the control interface SET command to be used to update the
sched_scan_plans parameter at runtime. In addition, an empty string can
be used to clear the previously configured plan.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2015-11-30 14:03:28 +02:00
Avraham Stern
32c02261dd Add support for configuring scheduled scan plans
Add the option to configure scheduled scan plans in the config file.
Each scan plan specifies the interval between scans and the number
of scan iterations. The last plan will run infinitely and thus
specifies only the interval between scan iterations.

usage:
sched_scan_plans=<interval:iterations> <interval2:iterations2> ... <interval>

Signed-off-by: Avraham Stern <avraham.stern@intel.com>
2015-11-30 14:03:28 +02:00
Kanchanapally, Vidyullatha
4ead7cfd5d Abort an ongoing scan before connect
Connect radio work is sometimes delayed for a considerable duration if
there is an ongoing scan radio work. To avoid these delays abort the
ongoing scan on that interface before queuing a connect request. Upon a
scan done indication from the driver, connect radio work will be
scheduled.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2015-11-26 19:44:14 +02:00
Ahmad Kholaif
0f29bc68d1 IBSS/mesh: Add support for VHT80P80 configuration
A new network profile configuration parameter max_oper_chwidth=3 can be
used to specify preference to enable 80+80 MHz VHT channel for IBSS. If
that is set, the first 80 MHz segment is specified based on the
frequency parameter in the network profile and the second segment is
selected automatically (which will practically be limited to a single
possibility due to DFS requirements in most countries).

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2015-11-26 17:47:15 +02:00
Jouni Malinen
9e68742ef1 Fix CONFIG_NO_WPA=y build
Number of places were calling functions that are not included in
CONFIG_NO_WPA=y build anymore. Comment out such calls. In addition, pull
in SHA1 and MD5 for config_internal.c, if needed.

Signed-off-by: Jouni Malinen <j@w1.fi>
2015-11-23 23:34:52 +02:00
Jouni Malinen
d38c7be0f0 Skip SELECT_NETWORK steps only if already connected or connecting
Commit 2a6f78fbbe ('Do not re-associate on
SELECT_NETWORK to current network') started skipping all SELECT_NETWORK
connection steps if the selected network had already been selected
previously. This happened regardless of whether the connection was
already established. This is not necessarily desirable for all cases
where there is no immediate action to even try to connect (e.g., long
wait for the next scan).

Speed this up by allowing the SELECT_NETWORK operation to get started if
there is no connection or ongoing connection attempt with the selected
network.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2015-11-20 00:45:40 +02:00
Peter Oh
a65efbfb24 Add VHT support for Mesh
Mesh Points themselves have capability to support VHT as long as
hardware supports it. However, supporting VHT in mesh mode was disabled
because no one had clearly tested and confirmed its functionality. Since
VHT80 has now been verified to work with ath10k QCA988X driver and
mac80211_hwsim, enable VHT support in mesh mode.

Signed-off-by: Peter Oh <poh@qca.qualcomm.com>
2015-11-19 11:37:41 +02:00
Lubomir Rintel
1248e58492 wpa_supplicant: Reopen debug log file upon receipt of SIGHUP signal
This is useful for logrotate to be able to rotate the file even if the
control interface is not enabled (e.g., when using DBus).

Signed-off-by: Lubomir Rintel <lkundrak@v3.sk>
2015-10-25 20:45:02 +02:00
Jouni Malinen
a8412ec9d0 Clear own_disconnect_req on new connection attempt
It was possible for wpa_s->own_disconnect_req to be left set to 1 from a
disconnection attempt from a prior connection. This could then prevent
proper connection failure processing with the new connection in
wpas_connection_failed(). This was triggered by the following hwsim test
case sequence: wpas_mesh_secure sae_no_ffc_by_default. In this sequence,
the SAE failure due to unsupported group did not result in proper
wpas_connection_failed() processing and retry.

Fix this by clearing wpa_s->own_disconnect_req in
wpa_supplicant_associate() before starting a new connection.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2015-10-12 14:24:06 +03:00
Kanchanapally, Vidyullatha
e903d32d41 Parallelize distinct radio work operations
This commit contains the necessary changes to parallelize
distinct radio work operations which are different in type and
the band used, only when the underlying driver is capable of
supporting such simultaneous offchannel operations.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2015-10-01 01:41:46 +03:00
Andrei Otcheretianski
22264b3c61 Fix get_shared_radio_freqs_data() used-by flags setting
Fix an iteration bug in get_shared_radio_freqs_data when building
freqs_data array. Only the last used-by flag was maintained instead of
making this a bitfield of all found uses.

Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
2015-09-25 21:02:55 +03:00
Masashi Honma
241c33335b mesh: Add support for scanning only the current frequency
This patch enables scan_cur_freq=1 on VIF based mesh network.

Signed-off-by: Masashi Honma <masashi.honma@gmail.com>
2015-09-25 20:59:32 +03:00
Jouni Malinen
5a1d9d1a8e Avoid reconnection on ENABLE_NETWORK if already connected
This was already the case for most command sequences, but it was
possible for wpa_s->reassociate to be set to 1 when CTRL-RSP-* commands
were used to set identity, password, or passphrase for EAP
authentication. In such cases, ENABLE_NETWORK issued after the
connection was completed could result in a new connection attempt
(likely reconnection back to the same BSS).

Fix this by checking whether an actual connection is already present
even if wpa_s->reassociate is set when processing the ENABLE_NETWORK
command.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2015-09-22 11:55:54 +03:00
Jouni Malinen
8406cd3515 Make it clearer that ap_scan=2 mode should not be used with nl80211
Add more details into configuration comments and a runtime info message
if ap_scan=2 is used with the nl80211 driver interface.

Signed-off-by: Jouni Malinen <j@w1.fi>
2015-09-05 01:04:29 +03:00
Jouni Malinen
35d403096e Set NORMAL_SCAN_REQ on SELECT_NETWORK/ENABLE_NETWORK
wpa_s->scan_req needs to be set in these cases to get correct scanning
behavior. This is mainly needed for starting of AP mode operation
immediately in ap_scan=2 case.

This fixes an issue that was found with mac80211_hwsim test cases in the
following sequence: dbus_autoscan dbus_ap_scan_2_ap_mode_scan

Signed-off-by: Jouni Malinen <j@w1.fi>
2015-08-17 00:18:32 +03:00
Mahesh A Saptasagar
0d0f7ecbb1 Do not stop ongoing PNO sched_scan on association/disconnection
PNO was stopped by the wpa_supplicant during the connection attempts or
while handling disassociation indication. External entities, mainly, the
Android Wi-Fi framework, does not expects PNO to be stopped by other
modules. Hence, do not stop the sched_scan in these scenarios if it is
triggered externally for PNO.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2015-08-13 21:10:16 +03:00
Hu Wang
6108536d7d Drop connection attempt if network is disabled before radio work starts
With the radio work design, it is possible for a network entry to get
disabled (e.g., DISABLE_NETWORK <id>) during the time the connect or
sme-connect radio work waits to start. Previously, only the validity of
the BSS entry and BSSID/SSID was verified when starting the actual
connection step. Add call to wpas_network_disabled() to those checks to
catch the case where the network profile is disabled.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2015-08-10 22:16:19 +03:00
Jouni Malinen
84bcb4e7a9 FST: Mark fst_ies buffer const
This buffer is owned by the FST module, so mark it const in the
set_ies() callback to make it clearer which component is responsible for
modifying and freeing this.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2015-08-03 17:40:30 +03:00
Gautam
d4e597959c P2P: Fix P2P configuration file name
The P2P configuration file is wrongly set as STA configuration file,
even though a separate configuration file is mentioned with '-m' option.
Add initialization and deallocation of global.params->conf_p2p_dev to
fix this.

Signed-off-by: Gautam <gautams@broadcom.com>
2015-08-02 21:37:09 +03:00
Jouni Malinen
3188aabaf1 Add shared periodic cleanup function for AP mode
This new mechanism can be used to combine multiple periodic AP
(including P2P GO) task into a single eloop timeout to minimize number
of wakeups for the process. hostapd gets its own periodic caller and
wpa_supplicant uses the previously added timer to trigger these calls.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2015-07-20 13:33:30 +03:00
Jouni Malinen
8c0d0ff22e Use a single cleanup timer per wpa_supplicant process
Previously, one timeout per process (by default every 30 seconds) was
used P2P peer expiration and another per-interface timeout (every 10
seconds) was used to expire BSS entries. Merge these to a single
per-process timeout that triggers every 10 seconds to minimize number of
process wakeups due to periodic operations.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2015-07-20 13:28:12 +03:00
Jouni Malinen
a0f04da517 FST: Mark get_mb_ie() return value const
The caller is not expected to free or modify the value since this is
returning a reference to a buffer maintained by the upper layer.

Signed-off-by: Jouni Malinen <j@w1.fi>
2015-07-18 17:23:55 +03:00
Jouni Malinen
b7a07937ee FST: Show FST IE update details in debug log
This makes it more convenient to debug FST IE updates.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2015-07-17 16:29:20 +03:00
Anton Nayshtut
b36a3a65aa FST: Integration into wpa_supplicant
This commit integrates the FST into the wpa_supplicant.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2015-07-16 18:26:15 +03:00
Ilan Peer
f43c1ae798 P2P: Handle P2P Device dedicated interface parent removal
In case of a network interface removal, check if the interface
was also the parent interface of the P2P Device dedicated interface.
If this is the case, then stop the P2P Device functionality, and
remove the P2P Device dedicated interface.

In case that the interface is added again and P2P Device
functionality can be enabled again, add a new P2P Device dedicated
interface and allow further P2P Device functionality.

In case that the P2P Device dedicated interface is re-created, the
original P2P Device configuration file is needed, so store it in
the global params (instead in the wpa_interface configuration).

Signed-off-by: Ilan Peer <ilan.peer@intel.com>
2015-06-19 16:22:26 +03:00
Max Stepanov
07c1e987d5 P2PS: Enable Probe Request frame processing by P2P Client
1. Add global p2p_cli_probe property to enable/disable Probe Request
frame RX reporting for connected P2P Clients. The property can be set to
0 - disable or 1 - enable. The default value is 0.

2. Enable Probe Request frame RX reporting for P2P Client on
WPA_COMPLETED state if p2p_cli_probe property is set to 1. Disable it
when an interface state is changing to any other state.

3. Don't cancel Probe Request frame RX reporting on wpa_stop_listen for
a connected P2P Client handling Probe Request frames.

Signed-off-by: Max Stepanov <Max.Stepanov@intel.com>
Reviewed-by: Ilan Peer <ilan.peer@intel.com>
2015-06-14 23:16:55 +03:00
Ilan Peer
57e832de37 GAS: Remove all radio works before calling gas_query_deinit()
Remove all gas-query radio works before calling gas_query_deinit()
as gas_query_deinit() flow frees the query context, which might
be later be accessed from the radio work callback (and result
with unexpected behavior, e.g., segmentation fault).

Signed-off-by: Ilan Peer <ilan.peer@intel.com>
2015-06-11 02:57:34 +03:00
Jouni Malinen
e66bcedd3e Do not set own_disconnect_req flag if not connected
This fixes some issues where a disconnection event may get ignored if an
earlier operation to remove or disable a network resulted in an attempt
to disconnect event though no connection was in place.
wpa_s->current_ssid != NULL alone is not sufficient to determine that
there will be a driver event notifying completion of such disconnection
request. Set own_disconnect_req to 1 only if wpa_s->wpa_state is also
indicating that there is a connection or an attempt to complete one.

This showed up in a failure, e.g., when running the hwsim test case
scan_int followed by ap_vlan_wpa2_psk_radius_required where the latter
ended up not processing a connection failure event and getting stuck not
trying to run a new scan and connection attempt.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2015-06-10 15:42:57 +03:00
Krishna Vamsi
a80651d067 Add support to request a scan with specific SSIDs
Support a request to scan specific SSIDs given by user with the SCAN
command. The SSID list can be suffixed to the scan command as follows.
For example, if SSIDs "ABC" and "abc123" need to be specifically
scanned, the command should be "SCAN ssid 414243 ssid 616263313233". The
value of the SSID is passed in hexadecimal representation.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2015-06-05 15:55:26 +03:00
Sunil Dutt
4d3be9cdd1 Postpone updating of wpa_s->current_bss till association event
In the case of driver-based BSS selection, a bssid_hint in the connect
request might not result in to the selection of the same BSS. Thus,
postpone the updation of the wpa_s->current_bss till the association
event is received unless the BSSID is forced. This fixes issues where
wpa_s->current_bss may end up being updated to point to the BSS that
wpa_supplicant provided as a hint for a roaming case, but then not
restored if the driver decides to "return" to the current BSS instead.
This could result in some operations (e.g., WNM BSS TM response) not
working properly due to incorrect BSS being identified in
wpa_s->current_bss.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2015-05-29 12:18:13 +03:00
Jouni Malinen
c7dafdf9b0 WPS: Fix build without CONFIG_WPS=y
Commit 5add410162 ('WPS: Use shorter
authentication timeout during no-SelReg iteration') broke the build with
WPS disabled.

Signed-off-by: Jouni Malinen <j@w1.fi>
2015-05-24 10:33:26 +03:00
Jouni Malinen
0ef1e290ab WPS: Fix shorter authentication timeout during no-SelReg iteration
Commit 5add410162 ('WPS: Use shorter
authentication timeout during no-SelReg iteration') added a new
condition on reducing the authentication timeout for the WPS AP
iteration process. However, due it ended up copy-pasting an incorrect
condition for this. This was supposed to apply for PIN-based config
method advertisement, not PBC.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2015-04-28 00:12:36 +03:00
Mikael Kanstrup
8b423edbd3 Declare all read only data structures as const
By analysing objdump output some read only structures were found in
.data section. To help compiler further optimize code declare these
as const.

Signed-off-by: Mikael Kanstrup <mikael.kanstrup@sonymobile.com>
2015-04-25 17:33:06 +03:00
Jouni Malinen
5add410162 WPS: Use shorter authentication timeout during no-SelReg iteration
When iterating through WPS APs that do not advertise Selected Registrar
TRUE, limit the authentication timeout to 10 seconds instead of the full
70 second value used with IEEE 802.1X/EAP/WPS in general. This helps
speed up AP iteration for cases where a selected AP misbehaves and does
not reply to EAP exchanges. This should not really be needed, but there
seems to be deployed APs that do not implement WPS correctly and with
such APs in the radio range, this extra timeout can speed up the
iteration to allow the correct AP to be found before the WPS operation
times out.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2015-04-24 17:55:32 +03:00
Ilan Peer
74802c0936 P2P: Do not create a P2P Device interface if P2P is disabled
Do not add the dedicated P2P Device interface in case P2P is disabled in
the configuration file or globally.

Signed-off-by: Ilan Peer <ilan.peer@intel.com>
2015-04-24 01:22:15 +03:00
Jouni Malinen
eaa8eefed1 Replace MAX_SSID_LEN with SSID_MAX_LEN
This makes source code more consistent. The use within Android driver
interface is left as-is to avoid changes in the old PNO interface
definition.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2015-04-22 11:44:18 +03:00
Jason Abele
a20a3616cd wpa_supplicant: Clear blacklist on connect
It has been noticed that the band steering/load balancing of some
multi-AP networks will lead to an ever-growing list of blacklisted
BSSIDs. This eventually leads to a connection drop when the connection
is pushed to a distant AP.

Fix this issue by clearing the blacklist upon successful connect.

Signed-off-by: Jason Abele <jason@aether.com>
2015-04-03 10:51:36 +03:00
Jouni Malinen
a52410c29f Allow PSK/passphrase to be set only when needed
The new network profile parameter mem_only_psk=1 can be used to specify
that the PSK/passphrase for that network is requested over the control
interface (ctrl_iface or D-Bus) similarly to the EAP network parameter
requests. The PSK/passphrase can then be configured temporarily in a way
that prevents it from getting stored to the configuration file.

For example:

Event:
CTRL-REQ-PSK_PASSPHRASE-0:PSK or passphrase needed for SSID test-wpa2-psk

Response:
CTRL-RSP-PSK_PASSPHRASE-0:"qwertyuiop"

Note: The response value uses the same encoding as the psk network
profile parameter, i.e., passphrase is within double quotation marks.

Signed-off-by: Jouni Malinen <j@w1.fi>
2015-03-28 11:05:13 +02:00
Avraham Stern
9bd566a33a Delay AP selection if all networks are temporarily disabled
If all networks are temporarily disabled, delay AP selection until at
least one network is enabled. Running AP selection when all networks are
disabled is useless as wpa_supplicant will not try to connect. In
addition, it will result in needless scan iterations that may delay the
connection when it is needed.

Signed-off-by: Avraham Stern <avraham.stern@intel.com>
2015-03-22 20:53:58 +02:00
Avraham Stern
701f3961e3 Don't optimize scan frequencies if selected network has changed
When disconnecting from a BSS, the next scan is optimized to scan only
the channels used by the connected ESS. But when disconnecting because a
new network was selected, this optimization is wrong because
wpa_supplicant is now trying to connect to another ESS. Fix this by not
optimizing the scan frequencies in case the selected network has
changed.

Signed-off-by: Avraham Stern <avraham.stern@intel.com>
2015-03-22 20:36:01 +02:00
Jouni Malinen
9feadba141 Remove unnecessary NULL check to make function more consistent
Static analyzers may warn about dereference before NULL check in
wpas_network_disabled() due to the new code added to check
wpa_s->p2p_mgmt. wpa_s cannot be NULL here, so remove the unneeded check
for it later in the function. (CID 106124)

Signed-off-by: Jouni Malinen <j@w1.fi>
2015-03-01 22:36:53 +02:00
Jouni Malinen
1772d348ea P2P: Fix interface deinit for failed group interface initialization
wpa_supplicant_deinit_iface() ends up removing all P2P groups if the
removed interface is the parent interface. This is correct behavior in
general, but this resulted in issues in the new group interface
initialization error path since wpa_s->parent was not assigned before
hitting this check. Fix this by assigning wpa_s->parent as part of
wpa_supplicant_add_iface().

Signed-off-by: Jouni Malinen <j@w1.fi>
2015-03-01 22:36:53 +02:00
Jouni Malinen
c28059091a Do not add blacklist entries based on normal disconnect request cases
There are number of cases where wpa_supplicant requests the current
connection to be disconnected before starting a new operation. Such
cases do not really indicate that there was an error in connecting or a
disconnection initiated by the AP, so do not add a temporary blacklist
entry in such sequences.

Signed-off-by: Jouni Malinen <j@w1.fi>
2015-03-01 15:54:24 +02:00
Jouni Malinen
44b9ea5bb2 P2P: Do not allow scan or normal association on cfg80211 P2P Device
The dedicated P2P management instance (wpas->p2p_mgmt == 1) using
cfg80211 P2P Device cannot be used for non-P2P uses or connection (there
is no netdev). Reject or ignore such operations to avoid unexpected
operations if enabled network blocks are configured in the
wpa_supplicant instance used to control this interface.

Signed-off-by: Jouni Malinen <j@w1.fi>
2015-03-01 11:23:09 +02:00
Janusz Dziedzic
c3dabf5a00 Fix merge issue with IBSS VHT support
Commit 563ee1832b ('IBSS: Add support for
VHT80 configuration') got merged in incorrectly with one i/j swap
missed.

Signed-off-by: Janusz Dziedzic <janusz.dziedzic@tieto.com>
2015-02-28 16:48:22 +02:00
Jouni Malinen
a1b790eb9d Select AP based on estimated maximum throughput
This modifies the BSS selection routines to calculate SNR and estimated
throughput for each scan result and then use the estimated throughput as
a criteria for sorting the results. This extends the earlier design by
taking into account higher throughput rates if both the AP and local
device supports HT20, HT40, or VHT80. In addition, the maximum rate is
restricted based on SNR.

In practice, this gives significantly higher probability of selecting
HT/VHT APs when there are multiple BSSes in the same ESS and SNR is not
low enough to prevent higher MCS use.

Signed-off-by: Jouni Malinen <j@w1.fi>
2015-02-22 11:09:54 +02:00
Janusz Dziedzic
563ee1832b IBSS: Add support for VHT80 configuration
Configure VHT80 based on driver capabilities.

Signed-off-by: Janusz Dziedzic <janusz.dziedzic@tieto.com>
2015-02-21 16:07:53 +02:00
Janusz Dziedzic
98479dc95e IBSS: Update operating frequency if joining an existing IBSS
If a matching IBSS is found in scan results, change requested frequency
to match and disable OBSS scan.

Signed-off-by: Janusz Dziedzic <janusz.dziedzic@tieto.com>
2015-02-21 16:07:53 +02:00