Commit graph

54 commits

Author SHA1 Message Date
Jouni Malinen
bbc6c729a5 P2P: Use group formation timeout on persistent group GO
Previously, GO considered the group to be fully re-invoked after
starting beaconing on successful invitation exchange. This would leave
the group running until idle timeout (which may not be enabled) or
explicit removal if the client fails to connect for any reason. Since
the client is expected to connect immediately after the invitation
exchange that ends with status=0 (i.e., either client initiated the
exchange or it responded with success), extend group formation timeout
to cover that period until the first successfully completed data
connection. This allows the GO to remove the group automatically if the
client devices does not connect within
P2P_MAX_INITIAL_CONN_WAIT_GO_REINVOKE (15) seconds.

Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
2013-09-26 21:24:09 +03:00
Vinay Krishna Eranna
b2b688d18d P2P: Fix crash when failed to create GO interface
wpa_supplicant crashes if driver configuration for AP mode interface
configuration fails after group negotiation. This is because of a
regression from commit 1075b29571 that
ends up freeing the wpa_s instance from within
wpa_supplicant_create_ap() without the caller knowing.

Fix this by using an eloop timeout to free remove the P2P group so that
wpa_supplicant_create_ap() and especially wpa_supplicant_associate()
callers do not need to know about interface getting possibly removed. In
addition, move the P2P specific code into p2p_supplicant.c where it
really belongs. This allows the already existing group formation timeout
to be used by reducing the timeout to zero.

Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
2013-09-03 12:43:12 +03:00
Jouni Malinen
5bf9a6c859 P2P: Add event messages for possible PSK failures on P2P groups
It is possible for the GO of a persistent group to change the PSK or
remove a client when per-client PSKs are used and this can happen
without the SSID changing (i.e., the group is still valid, but just not
for a specific client). If the client side of such persistent group ends
up trying to use an invalidated persistent group information, the
connection will fail in 4-way handshake. A new WPS provisioning step is
needed to recover from this.

Detect this type of case based on two 4-way handshake failures when
acting as a P2P client in a persistent group. A new
"P2P-PERSISTENT-PSK-FAIL id=<persistent group id>" event is used to
indicate when this happens. This makes it easier for upper layers to
remove the persistent group information with "REMOVE_NETWORK <persistent
group id>" if desired (e.g., based on user confirmation).

In addition to indicating the error cases for persistent groups, all
this type of PSK failures end up in the client removing the group with
the new reason=PSK_FAILURE information in the P2P-GROUP-REMOVED event.

Signed-hostap: Jouni Malinen <j@w1.fi>
2013-09-01 21:35:10 +03:00
Jouni Malinen
f2c566027e P2P: Add a command for removing a client from all groups
The new control interface command P2P_REMOVE_CLIENT <P2P Device
Address|iface=Address> can now be used to remove the specified client
from all groups (ongoing and persistent) in which the local device is a
GO. This will remove any per-client PSK entries and deauthenticate the
device.

Signed-hostap: Jouni Malinen <j@w1.fi>
2013-09-01 21:35:10 +03:00
Jouni Malinen
01a57fe420 P2P: Maintain list of per-client PSKs for persistent groups
Record all generated per-client PSKs in the persistent group network
block and configure these for the GO Authenticator whenever re-starting
the persistent group. This completes per-client PSK support for
persistent groups.

Signed-hostap: Jouni Malinen <j@w1.fi>
2013-09-01 21:35:10 +03:00
Jouni Malinen
1075b29571 P2P: Report group formation failure on error to start GO mode
There is no need to wait for the 15 second group formation timeout
before indicating P2P group formation failure if GO mode cannot be
started successfully for some reason.

Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
2013-07-11 17:04:46 +03:00
Arend van Spriel
c68f6200a7 P2P: Create P2P Device interface if supported
If the capability flag of the driver indicates a dedicated P2P Device is
supported, a P2P Device interface is created.

Create the P2P Device in main interface creation loop when the added
interface flags support and P2P supplicant is not yet initialized
avoiding recursion of add_interface.

Do not register l2_packet for P2P Device interface (both for EAPOL and
for TDLS).

Signed-hostap: Arend van Spriel <arend@broadcom.com>
2013-06-30 10:50:14 +03:00
Jouni Malinen
f85f545e71 P2P: Use common function for re-starting P2P scan after station scan
Make the implementation more consistent and cleaner by using a single
function for addressing all the cases where completion of a station mode
scan operation allows a P2P operation (search) to be re-started.

Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
2013-03-18 17:32:31 +02:00
Jouni Malinen
5473362458 P2P: Use peer's channel list to limit GO freq on invitation
Peer device includes its list of allowed operating channels in the
Invitation Response frame. When we are becoming the GO, use that list
from the peer to filter out acceptable channels to avoid selecting a
channel that the peer is unable to use.

Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
2013-03-01 20:01:01 +02:00
Jouni Malinen
f5877af01e P2P: Allow P2P client to specify preferred group channel
When re-invoking a persistent group in P2P client role, the new
pref=<MHz> parameter can now be used with the p2p_invite command to
indicate a preferred operating frequency. Unlike the older freq=<MHz>
parameter, this leaves GO an option to select another channel (from our
supported channels) if the GO cannot accept the channel.

Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
2013-03-01 19:40:54 +02:00
Jouni Malinen
0aadd5682f Fix disconnection event processing
Commit 0d30cc240f forced
wpa_s->current_ssid and wpa_s->key_mgmt to be cleared in
wpa_supplicant_mark_disassoc() which gets called from
wpa_supplicant_event_disassoc(). This broke IEEE 802.1X authentication
failure processing and P2P deauthentication notification (group
termination).

Fix this by splitting wpa_supplicant_event_disassoc() into two parts and
make wpas_p2p_deauth_notif() indicate whether the interface was removed.
If so, the last part of disassocition event processing is skipped. Since
the wpa_supplicant_mark_disassoc() call is in the second part, the above
mentioned issues are resolved. In addition, this cleans up the P2P group
interface removal case by not trying to use fast reconnection mechanism
just before the interface gets removed.

Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
2012-08-31 22:04:41 +03:00
Jouni Malinen
4d32c0c44d P2P: Allow p2p_invite-persistent to specify channel for GO
The freq and ht40 parameters can now be used with the p2p_invite
command when reinvoking a persistent group as the GO.

Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
2012-08-31 21:20:51 +03:00
Jouni Malinen
347d6a5b76 WFD: Add support for sending Wi-Fi Display service discovery requests
wpa_cli p2p_serv_disc_req command can now be used to request WSD
request to be sent to specified or all peers who support WSD.

format: wifi-display <list of roles> <list of subelements>
examples:
p2p_serv_disc_req 00:00:00:00:00:00 wifi-display [source] 2,3,4,5
p2p_serv_disc_req 02:01:02:03:04:05 wifi-display [pri-sink] 3
p2p_serv_disc_req 00:00:00:00:00:00 wifi-display [sec-source] 2
p2p_serv_disc_req 00:00:00:00:00:00 wifi-display [source+sink] 2,3,4,5
p2p_serv_disc_req 00:00:00:00:00:00 wifi-display [source][pri-sink] 2,3,4,5

Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
2012-08-29 19:51:29 +03:00
Jouni Malinen
05a77b3b46 P2P: Use 500 ms search delay by default during concurrent operations
If the p2p_find command is used without the delay parameter, a 500 ms
default search delay will now be used when any interface using the same
radio is in an concurrent operation. "p2p_find delay=0" can be used to
enforce the old behavior in such a case if needed.

Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
2012-08-23 18:34:57 +03:00
Jouni Malinen
37448ede31 P2P: Add option for adding extra delay to p2p_find
A new optional delay=<search delay in milliseconds> parameter can now be
used with p2p_find command to request an extra delay between search
iterations. This can be used, e.g., to make p2p_find friendlier to
concurrent operations by avoiding it from taking 100% of the radio
resources.

Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
2012-08-23 18:20:58 +03:00
Rajkumar Manoharan
e2308e4b45 P2P: Add optional "ht40" argument for p2p_connect
This can be used to start negotiated GO in 40 MHz channel width
in 5GHz band.

Signed-hostap: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
2012-08-15 23:07:44 +03:00
Rajkumar Manoharan
7aeac98509 P2P: Enable 40 MHz support for autonomous P2P group addition
Add optional "ht40" argument for p2p_group_add command to enable 40 MHz
in 5GHz band. This configures the secondary channel, when HT support is
enabled and if the HW supports 40 MHz channel width.

Signed-hostap: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
2012-08-15 22:53:01 +03:00
Jouni Malinen
3bc462cb88 P2P: Add option for Provision Discovery before GO Negotiation
This is a workaround for interoperability issues with some deployed P2P
implementations that require a Provision Discovery exchange to be used
before GO Negotiation. The new provdisc parameter for the p2p_connect
command can be used to request this behavior without having to run a
separate p2p_prov_disc command.

Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
2012-05-11 16:25:47 +03:00
Jouni Malinen
6f251b6bb5 P2P: Store SSID of the group in p2p_group data
This can be used with P2P management operations that need to verify
whether the local device is operating a specific group based on
P2P Group ID attribute from a peer.

Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
2012-05-08 17:38:57 +03:00
Jouni Malinen
aa9bb7644b P2P: Allow older scan results to improve p2p_connect-auto robustness
Previusly the peer was assumed to not be operating a GO if the BSS entry
for it was not updated in the single scan run started by
p2p_connect-auto. This is not very robust since a scan may miss the peer
if either a Probe Request or Probe Response frame is lost. Improve
robustness by assuming the peer is still operating the GO and starting
the join operation. If the GO is not found during PD-for-join or the
single-channel scans during the join, fall back to GO Negotiation.

Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
2012-05-08 17:38:57 +03:00
Jouni Malinen
23c84252a4 P2P: Add option to force SSID/passphrase for GO Negotiation
An existing persistent group information can now be used to force GO
Negotiation to use the previously used SSID/passphrase from a persistent
group if we become a GO. This can be used as an alternative to inviting
a new P2P peer to join the group (i.e., use GO Negotiation with GO
intent 15 instead of starting an autonomous GO and using invitation),
e.g., in case a GO Negotiation Request is received from a peer while we
are not running as a GO. The persistent group to use for parameters is
indicated with persistent=<network id> parameter to p2p_connect.

Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
2012-04-27 18:25:30 +03:00
Jouni Malinen
0918c4bf3b P2P: Add p2p_prov_disc auto mechanism
wpa_supplicant can now be requested to automatically figure out whether
the indicated peer is operating as a GO and if so, use join-a-group
style PD instead of pre-GO Negotiation PD.

Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
2012-04-26 17:13:03 +03:00
Jouni Malinen
b31be3a0fd P2P: Add automatic GO Negotiation vs. join-a-group selection
p2p_connect command can now be used with an optional "auto" parameter
to request wpa_supplicant to determine automatically whether to use
join-a-group operation (if the peer is operating as a GO) or group
formation. This makes it easier for external programs to handle
connection type selection by offloading this to wpa_supplicant. The
previously used p2p_connect join commands can be replaced with
p2p_connect auto to use this new mechanism.

Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
2012-04-13 16:04:36 +03:00
Jouni Malinen
3fc14102f8 P2P: Remove client group on Deauthentication reason code 3
The GO can indicate that the P2P Group session is ending by sending a
Deauthentication frame with reason code 3 (Deauthenticated because
sending STA is leaving) based on P2P specification section 3.2.9. Use
this reason code to remove the P2P client group without waiting for the
group idle timeout.

Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
2012-04-03 16:45:28 +03:00
Johannes Berg
baf513d695 Pass signal strength through, fix units
The signal strength is currently never used as the only driver reporting
it is nl80211 which uses IEEE80211_RADIOTAP_DB_ANTSIGNAL which is never
populated by the kernel. The kernel will (soon) populate
IEEE80211_RADIOTAP_DBM_ANTSIGNAL instead though, so use that.

Also, since it was never really populated, we can redefine the signal
field to be in dBm units only.

My next patch will also require knowing the signal strength of probe
requests throughout the code (where available), so add it to the
necessary APIs.

Signed-hostap: Johannes Berg <johannes.berg@intel.com>
2012-04-01 18:48:12 +03:00
Jouni Malinen
e22d4d957b Remove the GPL notification from files contributed by Atheros
Remove the GPL notification text from files that were initially
contributed by Atheros Communications or Qualcomm Atheros.

Signed-hostap: Jouni Malinen <j@w1.fi>
2012-02-11 19:39:36 +02:00
Jouni Malinen
c427ac9211 P2P: Set Invitation Type to 1 for GO inviting to a persistent group
When a GO is operating a persistent group and invites a peer that has
been a P2P client in that persistent group, the Invitation Type in the
Invitation Request frame can be set to 1 to indicate that this is a
reinvocation of a persistent group. Do this based on the maintained
list of P2P clients that have been provided the credentials to this
group.

Signed-hostap: Jouni Malinen <j@w1.fi>
2012-02-06 21:54:36 +02:00
Jouni Malinen
6d92fa6e92 P2P: Allow Device ID to be specified for p2p_find command
dev_id=<P2P Device Addr> can now be specified as an argument to
p2p_find to request P2P find for a specific P2P device.

Signed-hostap: Jouni Malinen <j@w1.fi>
2012-01-08 09:25:29 -08:00
Jouni Malinen
fbdcfd577a P2P: Maintain a list of P2P Clients for persistent group on GO
Add a new persistent group network block field, p2p_client_list, to
maintain a list of P2P Clients that have connected to a persistent
group. This allows GO of a persistent group to figure out more easily
whether re-invocation of a persistent group can be used with a specific
peer device.

Signed-hostap: Jouni Malinen <j@w1.fi>
2011-12-22 22:47:41 +02:00
Jouni Malinen
87f841a140 P2P: Show persistent group info on P2P_PEER data
Add "persistent=<network id>" line to P2P_PEER ctrl_iface data
if a persistent group credentials are available for this peer.
This makes it easier for external programs to figure out when
a persistent group could be re-invoked with this peer.

For now, this information is only available on the P2P client,
but similar information can be added for GO once a list of P2P
clients is maintained with the persistent group data.

Signed-hostap: Jouni Malinen <j@w1.fi>
2011-12-22 21:45:20 +02:00
Jouni Malinen
7165c5dc1f P2P: Fix 32-bit compiler warnings on service discovery reference
Convert core wpa_supplicant code to use u64 instead of void * for the
P2P service discovery reference. Use uintptr_t in type casts in
p2p_supplicant.c to handle the conversion without warnings.

Note: This needs to be revisited for 128-bit CPU where sizeof(void *)
could be larger than sizeof(u64).

Signed-hostap: Jouni Malinen <j@w1.fi>
2011-12-11 18:06:34 +02:00
Jouni Malinen
502618f7c1 P2P: Clean up group formation on network block removal
If a P2P group network block is removed for any reason (e.g., wps_cancel
command) while the interface is in group formation, remove the group
formation timeout and indicate failure immediately. Previously, this
type of operations could end up leaving the timeout running and result
in somewhat unexpected group formation failure events later.

Signed-hostap: Jouni Malinen <j@w1.fi>
2011-12-10 12:56:42 +02:00
Jouni Malinen
c3f4278445 P2P: Add group ifname to P2P-PROV-DISC-* events
If Provision Discovery Request is sent for GO role (i.e., P2P Group ID
attribute is included), add the group interface name to the control
interface event on the GO. This makes it easier to figure out which
ctrl_iface needs to be used for wps_pbc/wps_pin command to authorize
the joining P2P client.

Signed-hostap: Jouni Malinen <j@w1.fi>
2011-12-06 21:57:17 +02:00
Jithu Jance
8c5f730983 P2P: Add optional "join" argument for p2p_prov_disc command
This can be used to request Provision Discovery Request to be sent
for the purpose of joining a running group, e.g., to request the GO
to display a PIN that we can then use with p2p_connect join command.

Signed-hostap: Jithu Jance <jithu@broadcom.com>
2011-12-06 21:28:02 +02:00
Jouni Malinen
303f60d39b P2P: Do not request station mode scans during P2P operations
The P2P search mechanism depends on the same scan functionality that
is used for station mode scans. If these operations are being used
at the same time, scan result processing is not handled properly.
Avoid unexpected behavior by delaying station mode scan requests
if a P2P operation is in progress.

Among other things, this allows the station mode connection attempt
to be continued after a P2P find or group formation has been completed
if the interface is available (i.e., when the P2P group uses a
separate virtual interface).
2011-09-29 16:53:55 +03:00
Jouni Malinen
04a85e4401 P2P: Filter Probe Request frames based on DA and BSSID in Listen state
Only accept Probe Request frames that have a Wildcard BSSID and a
destination address that matches with our P2P Device Address or is the
broadcast address per P2P specification 3.1.2.1.1.
2011-07-15 20:28:46 +03:00
Jayant Sane
3734552f15 P2P: Add WpsFailed signal in P2P D-Bus
Signal is triggered if an error occurs during WPS provisioning phase.

Signed-off-by: Jean-Michel.Bachot <jean-michelx.bachot@intel.com>
Signed-off-by: Jayant Sane <jayant.sane@intel.com>
2011-06-25 11:47:04 +03:00
Jean-Michel Bachot
046ef4aa67 P2P: Add option for requested device type in P2P search/scan
With this, p2p_find can be extended to find certain requested device
types.

Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2011-03-19 12:57:46 +02:00
Johannes Berg
8fd7dc1b1c P2P: Add new_device flag to dev_found callback
The DBus code will want to have perfect matching of dev_found and the
dev_lost it adds so it doesn't need to keep track internally. Enable
that with a new flag in the core that tracks whether we have already
notified about this -- the existing users can ignore it.

The part where this is always set to 1 if the new device is discovered
by a driver that has P2P in the driver is buggy -- the driver should
feed the P2P peer database and then that should feed the notification
here instead.

Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2011-02-24 21:59:58 +02:00
Konguraj(Raj) Kulanthaivel
c5db8e5170 P2P: Embed publically visible struct in peer info
This embeds some information about each P2P peer that will be publically
visible in a struct that is shared.

The dev_found notification function is also passed the new struct, which
requires some work for the driver-based P2P management.

Signed-off-by: Konguraj(Raj) Kulanthaivel <konguraj.kulanthaivel@intel.com>
Signed-off-by: Fabien Marotte <fabienx.marotte@linux.intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2011-02-24 21:51:17 +02:00
Johannes Berg
3103f34576 P2P: Add wpas_p2p_disconnect()
Add a new API function wpas_p2p_disconnect()
to disconnect from or dissolve a group.

Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2011-02-02 17:30:15 +02:00
Sudhakar Swaminathan
9d562b7946 P2P: Add p2p_unauthorize command
This can be used to remove authorization from a previous p2p_connect
commands that has not yet resulted in completed GO Negotiation.
2010-11-25 13:09:50 +02:00
Anil Gathala Sudha
7cfc4ac319 P2P: Add support for automatic channel selection at GO
The driver wrapper may now indicate the preferred channel (e.g., based
on scan results) on both 2.4 GHz and 5 GHz bands (and an overall best
frequency). When setting up a GO, this preference information is used
to select the operating channel if configuration does not include
hardcoded channel. Similarly, this information can be used during
GO Negotiation to indicate preference for a specific channel based
on current channel conditions.

p2p_group_add command can now use special values (freq=2 and freq=5)
to indicate that the GO is to be started on the specified band.
2010-11-10 13:33:47 +02:00
Jouni Malinen
c973f3868a P2P: Remove P2P group on driver resource becoming unavailable
Add a new driver event, EVENT_INTERFACE_UNAVAILABLE, for indicating
that the driver is not able to continue operating the virtual
interface in its current mode anymore, e.g., due to operating
channel for GO interface forced to a DFS channel by another virtual
interface.

When this happens for a P2P group interface, the P2P group will
be terminated and P2P-GROUP-REMOVED event shows the reason for
this as follows:
P2P-GROUP-REMOVED wlan0 GO reason=UNAVAILABLE
2010-10-25 19:16:11 +03:00
Jouni Malinen
59eba7a2b3 P2P: Add p2p_cancel command for cancelling ongoing group formation 2010-10-19 15:53:28 +03:00
Jouni Malinen
93b7ddd032 P2P: Skip GO Neg Conf ack failure workaround of send failures
The workaround to ignore no ctrl::ack received for GO Negotiation
Confirmation frame was only supposed to be used when the frame was
actually transmitted and just the ack was not received. However, due
to the way the driver failure on transmitting the frame were reported,
this ended up getting applied for all failures in sending the GO
Negotiation Confirmation frame.

Improve this by providing a mechanism to indicate whether send_action
operations fail locally before the frame was actually transmitted or
because of not receiving ack frame after having transmitted the frame.
2010-10-19 12:47:33 +03:00
Jouni Malinen
b5c9da8db3 P2P: Add mechanism for updating P2P channel list based on driver events
This allows P2P channel list to be updated whenever the driver changes
its list of allowed channels, e.g., based on country code from scan
results.
2010-10-15 18:55:22 +03:00
Jouni Malinen
b73bf0a74b P2P: Stop connection attempt on PBC session overlap
The overlap condition cannot disappear before group formation timeout
hits, so there is no point in continuing in this case and failure can
be indicated immediately.
2010-09-10 10:30:25 -07:00
Jouni Malinen
812bf56ab1 Fix build without CONFIG_P2P=y 2010-09-09 07:20:28 -07:00
Jouni Malinen
3dfda83d9c P2P: Add Device Password ID to GO Neg Request RX event
This event indicates the Device Password ID that the peer tried
to use in GO Negotiation. For example:
P2P-GO-NEG-REQUEST 02:40:61:c2:f3:b7 dev_passwd_id=4
2010-09-09 07:17:20 -07:00