Use a specific return value, WPS-PBC-OVERLAP, to indicate a reason
for rejecting a wps_pbc command in wpa_supplicant AP mode if the
PBC mode cannot be started due to PBC session overlap having been
detected during monitor time.
This allows the user to complete WPS provisioning using PBC by
selected a specific Enrollee even if there are other Enrollees
in active PBC mode at the same time. The other Enrollees will be
rejected should they try to connect at the same time.
Ignore possible mismatches in the source address of the frame and only
use UUID-E to check whether a Probe Request or M1 is from the same
Enrollee when figuring out whether there is PBC session overlap. This
is needed to avoid potential issues with Enrollee devices that may have
multiple interfaces indicating active PBC state.
If there is already a link the requested peer, request start of
renegotiation instead of completely new link. This seems to be needed
to allow some driver to accept the trigger for a new negotiation.
tdls_testing 0x80 can now be used to request wpa_supplicant to send
a TDLS Setup Request frame (i.e., try to initiate TDLS setup)
whenever a TDLS Setup Request frame has been received from a peer.
Blindly clearing all struct wpa_tdls_peer members is a risky
operation since it could easily clear pointers to allocated
memory, etc. information that really should not be removed.
Instead of hoping that new code gets added here to restore
the important variables, reverse the approach and only clear
structure members one by one when needed.
This allows the same code path to be used for both protected and
unprotected configurations to limit need for duplicated code in
both the driver and wpa_supplicant.
This adds code for validating that the same Key Lifetime is used
throughout TPK handshake and enables TPK lifetime expiration and
renewal/teardown. These part seem to be working, but the actual
handling of TDLS Setup Confirm and renewal are not fully
functional yet.
tdls_testing bits:
bit 3 = use short TPK lifetime (301 seconds)
bit 4 = use wrong TPK lifetime in TDLS Setup Response
bit 5 = use wrong TPK lifetime in TDLS Setup Confirm
These special test cases can be configured at run time with "wpa_cli
tdls_testing <value>" where <value> is an integer (either as a decimal
or as a hex value with 0x prefix) bitmap of special features with
following bits available at this point:
bit 0 = long frame (add dummy subelement to make FTIE very long)
bit 1 = use alternative RSN IE (different RSN capab value and no extra
replay counters)
bit 2 = send incorrect BSSID in Link Identifier of TDLS Setup Request
(e.g., 1 = long FTIE, 2 = different RSN IE, 3 = both of those)
This is disabled by default and can be enabled for the build by
adding the following line to .config:
CFLAGS += -DCONFIG_TDLS_TESTING
This allows driver wrappers to indicate whether the association was
done using Association Request/Response or with Reassociation
Request/Response frames.
CFLAGS += -DCONFIG_VALGRIND can now be used to enable support for
Valgrind client requests to help in removing some non-issues from
Valgrind reports. This is mainly aimed at allowing unknown ioctl
results to be marked as defined data.
If the os_time_t variable used for the expiration time (seconds)
overflows when the registered timeout value is being added,
assume that the event would happen after an infinite time, i.e.,
would not really happen in practice. This fixes issues with
long key timeouts getting converted to immediate expiration due
to the overflow.
os_snprintf() can be a preprocessor macro and according to
C99 (6.10.3 clause 11) the results of having preprocessor directives
inside the macro arguments is undefined.
Build options can now be used to replace the location of client
sockets for UNIX domain socket control interface:
CFLAGS += -DCONFIG_CTRL_IFACE_CLIENT_DIR=\"/tmp\"
CFLAGS += -DCONFIG_CTRL_IFACE_CLIENT_PREFIX=\"wpa_ctrl_\"
The buffer size for routing socket is fixed to 2048.
This patch fix it to obtain the size from OS.
This patch worked on x86 platform with NetBSD 5.0.2.
This allows keystore:// prefix to be used with client_cert and
private_key configuration parameters.
Signed-off-by: Dmitry Shmidt <dimitrysh@google.com>
This will only retrieve information about peers that have been fully
discovered, not peers that are only half-discovered based on their Probe
Request frames.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The DBus code will want to have perfect matching of dev_found and the
dev_lost it adds so it doesn't need to keep track internally. Enable
that with a new flag in the core that tracks whether we have already
notified about this -- the existing users can ignore it.
The part where this is always set to 1 if the new device is discovered
by a driver that has P2P in the driver is buggy -- the driver should
feed the P2P peer database and then that should feed the notification
here instead.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This embeds some information about each P2P peer that will be publically
visible in a struct that is shared.
The dev_found notification function is also passed the new struct, which
requires some work for the driver-based P2P management.
Signed-off-by: Konguraj(Raj) Kulanthaivel <konguraj.kulanthaivel@intel.com>
Signed-off-by: Fabien Marotte <fabienx.marotte@linux.intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When using multiple vifs and dynamic vlan tagging is enabled on any
interface, the created AP VLAN interfaces get the BSSID of the first
AP mode interface instead of the BSSID of the corresponding AP mode
interface.
Example:
wlan0 - xx:xx:xx:xx:x0
wlan1 - xx:xx:xx:xx:x1
Assume a STA connects to the AP interface wlan1 and gets a dynamic
VLAN tag 100 assigned by the RADIUS server. Hostapd will create an AP
VLAN interface wlan1.100 but doesn't set an address for this interface
which results in wlan1.100 getting the same address as wlan0:
wlan1.100 - xx:xx:xx:xx:x0
As a result the STA that was moved to wlan1.100 isn't able to finish its
4-way handshake since mac80211 won't pass its frames to wlan1.100 due to
the different address.
To fix this issue make use of the address of the AP interface when
creating an AP VLAN interface.
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Add MAC addresses for stations and use wpa_msg instead of printf
methods to make it easier to grep logs and find messages for the
station in question.
Signed-off-by: Ben Greear <greearb@candelatech.com>
If parsing of the certificate or private key succeeds using any of
the tried encoding types, clear the OpenSSL error queue without
showing the pending errors in debug log since they do not really
provide any useful output and can be confusing.
This patch fixes a problem I had when I tried to connect
an embedded system [wpa_supplicant, CONFIG_TLS=internal]
to my TLS secured network.
TLSv1: Send CertificateVerify
TLSv1: CertificateVerify hash - hexdump(len=36): ha .. ha
PKCS #1: pkcs1_generate_encryption_block - Invalid buffer lengths \
(modlen=512 outlen=454 inlen=36)
It turned out that a fixed 1000 byte message buffer was just
a little bit too small for the 4096 bit RSA certificates
I'm using.
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
In multi BSS setups it wasn't possible to set up an HT BSS in
conjunction with a WEP/TKIP BSS. HT needed to be turned off entirely
to allow WEP/TKIP BSSes to be used.
In order to allow HT BSSes to coexist with non-HT WEP/TKIP BSSes add a
new BSS conf attribute "disable_11n" which disables HT capabilities on a
single BSS by suppressing HT IEs in the beacon and probe response
frames. Furthermore, mark all STAs associated to a WEP/TKIP BSS as
non-HT STAs. The disable_11n parameter is used internally; no new entry
is parsed from hostapd.conf.
This allows a non-HT WEP/TKIP BSS to coexist with a HT BSS without
having to disable HT mode entirely. Nevertheless, all STAs associated to
the WEP/TKIP BSS will only be served as if they were non-HT STAs.
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Use l2_packet with Ethernet header included so that the source
address for RRB packets can be forced to be the local BSSID. This
fixes problems where unexpected bridge interface address may end
up getting used and the recipient of the frame dropping it as
unknown R0KH/R1KH.
This is needed to keep kernel and hostapd in sync. In addition,
the obsolete entry in hostapd prevented use of Deauthentication
or Disassociation frame with reason code 6/7 mechanism to indicate
to the STA that there is no association if the STA missed the
broadcast Deauthentication frame for any reason.
The internal pointer to RADIUS client configuration needs to be
updated whenever a new hostapd configuration is loaded. Without
this, freed memory may be dereferenced and this can result in
segmentation faults.
This converts number of debugging messages to use wpa_msg() in order
to allow the interface name to be shown with the messages.
A new function, wpa_dbg(), is introduced to allow
CONFIG_NO_STDOUT_DEBUG=y builds to remove the debug strings. This is
otherwise identical with wpa_msg(), but it gets compiled out if stdout
debugging is disabled.
This is needed to allows WPS PBC session overlap detection to work
with drivers that process Probe Request frames internally. This
code is is run in hostapd, but the wpa_supplicant AP mode did not
have call to the hostapd_probe_req_rx() function even though it
registered handlers for hostapd Probe Request RX callbacks.
An optional parameter, p2p_dev_addr, can now be given to WPS_PBC
command on P2P GO to indicate that only the P2P device with the
specified P2P Device Address is allowed to connect using PBC. If
any other device tries to use PBC, a session overlap is indicated
and the negotiation is rejected with M2D. The command format for
specifying the address is "WPS_PBC p2p_dev_addr=<address>", e.g.,
WPS_PBC p2p_dev_addr=02:03:04:05:06:07
In addition, show the PBC session overlap indication as a WPS failure
event on an AP/GO interface. This particular new case shows up as
"WPS-FAIL msg=4 config_error=12".
This makes log files much more readable if multiple interfaces
are being controlled by the same process. The interface name is
added to stdout/file/syslog entries, but not to the messages
sent to control interface monitors to avoid issues with parsing
in external programs.
Signed-off-by: Ben Greear <greearb@candelatech.com>
Add a callback for station's authorized transitions
to allow wpa_supplicant to emit events in DBus.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
To enable making state change notifications on the WLAN_STA_AUTHORIZED
flag, introduce ap_sta_set_authorized(), and to reduce use of the flag
itself also add a wrapper for testing the flag: ap_sta_is_authorized().
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
If the driver advertises max_remain_on_chan data, use it instead of
the hardcoded value of 5000. Keep the default at 5000 since that is the
value used by earlier versions of cfg80211/mac80211 and not advertised
in nl80211 for those.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When authenticating, and the interface type is not already
NL80211_IFTYPE_STATION, we need to call wpa_driver_nl80211_set_mode()
only once. Remove the excessive call.
Signed-off-by: Eliad Peller <eliad@wizery.com>
We need to call this function after having completed the neighboring
channel scan to figure out whether HT40 can be used and if so, which
channel is the secondary channel.
ieee80211n_supported_ht_capab is called after ieee80211n_check_40mhz in
function hostapd_check_ht_capab. ieee80211n_check_40mhz can return 1 in
a valid scenario where the initialization is completed in a callback. In
this case ieee80211n_supported_ht_capab is skipped and hostapd does not
check the ht capabilities reported by the driver. Fix this issue making
sure ieee80211n_supported_ht_capab gets called.
Signed-off-by: Nishant Sarmukadam <nishants@marvell.com>
If WMM is not disabled explicitly (wmm_enabled=0 in hostapd.conf),
enable WMM automatically whenever HT (ieee80211n) is enabled. Use
the default WMM parameters for AP TX queues and the EDCA parameters
advertised for stations in WMM IE if no overriding values are
included in the configuration.
We can use the P2P interface types to check if the driver supports P2P
and to tell the kernel that a given interface is going to be used for
P2P (when it is created).
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
There is no real reason to maintain these in the current development
branch anymore. If someone really needs support for the obsolete
driver interfaces, these can be found in older wpa_supplicant
branches.
driver_atmel.c
- vendor-specific interface for ATMEL AT76C5XXx cards
- for some old out-of-tree driver; not for the upstream atmel*
drivers
driver_ndiswrapper.c
- vendor-specific interface for an out-of-tree driver
- ndiswrapper should work with driver_wext.c, too
driver_ipw.c
- vendor-specific interface for old ipw2100/2200 driver
- the upstream driver works with driver_wext.c (and does not work
with the old interface)
driver_hermes.c
- vendor driver that was not even included in the main wpa_supplicant
releases
In order to enable protection mechanisms for different HT opmodes the
driver needs to be aware of the current HT opmode that is calculated by
hostapd. Hence, pass the current opmode to the nl80211 driver via
the bss attribute NL80211_ATTR_BSS_HT_OPMODE.
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
tdls_prohibit=1 and tdls_prohibit_chan_switch=1 and now be used to
disable use of TDLS or TDLS channel switching in the BSS using
extended cabilities IE as defined in IEEE 802.11z.
Make sure that received management frames are long enough before
processing them. This avoids a potential segmentation fault if a
driver delivers an invalid frame all the way to hostapd.
The changes are:
1. the word "and" in the hunting-and-pecking string passed to the KDF
should be capitalized.
2. the primebitlen used in the KDF should be a short not an int.
3. the computation of MK in hostap is based on an older version of the
draft and is not the way it's specified in the RFC.
4. the group being passed into computation of the Commit was not in
network order.
Previously, only the Configuration Error values were indicated in
WPS-FAIL events. Since those values are defined in the specification
it is not feasible to extend them for indicating other errors. Add
a new error indication value that is internal to wpa_supplicant and
hostapd to allow other errors to be indicated.
Use the new mechanism to indicate if negotiation fails because of
WEP or TKIP-only configurations being disallows by WPS 2.0.
This needs to be done both in the more normal location in
p2p_timeout_connect_listen() (internal timeout after driver event) and
in p2p_listen_end() as a workaround for the case where the driver event
is delayed to happen after the internal timeout.
Previously, both NULL and ff:ff:ff:ff:ff:ff addr were used in various
places to indicate default/broadcast keys. Make this more consistent
and useful by defining NULL to mean default key (i.e., used both for
unicast and broadcast) and ff:ff:ff:ff:ff:ff to indicate broadcast
key (i.e., used only with broadcast).
When hostapd is removing a virtual BSS interface, the loop here was
incorrectly not updating the iterator during list traversal and
ended up in an infinite loop in some cases.
Use NULL instead of (u8 *) "" as the seq value and make sure the
driver wrapper implementations can handle NULL value. This was
previously already done in number of places, but not everywhere.
wpa_supplicant seems to crash from time to time on a NetBSD 4.0 MIPS
platform. The root cause turned out to be a MIPS alignment issue.
In my wpa_supplicant crash case, in function
wpa_driver_bsd_event_receive (from driver_bsd.c), the buf[2048] address
is started from i.e. 0x7fffd546, which is not 4 bytes aligned. Later
when it is casted to (struct if_msghdr *), and rtm->rtm_flags is used.
rtm->rtm_flags is "int" type, but its address is not 4 bytes aligned.
This is because the start address of rtm is not 4 bytes aligned.
Unfortunately in NetBSD MIPS kernel (unlike Linux MIPS kernel emulates
unaligned access in its exception handler), the default behavior is to
generate a memory fault to the application that accesses unaligned
memory address. Thus comes the early mentioned wpa_supplicant crash. An
interesting note is when I'm using the wpa_supplicant version 0.4.9, I
never saw this problem. Maybe the stack layout is different. But I
didn't look into details.
I used below patch to resolve this problem. Now it runs correctly for at
least several hours. But you might have a better fix (maybe we can use
malloc/free so that it is at least cache line aligned?). I'm also not
sure if other drivers should have the same problem.
This adds partial callbacks and events to allow P2P management to be
implemented in a driver/firmware. This is not yet complete and is
very much subject to change in the future.
CONFIG_WPS_REG_DISABLE_OPEN=y can be used to configure wpa_supplicant
to disable open networks by default when wps_reg command is used to
learn the current AP settings. When this is enabled, there will be a
WPS-OPEN-NETWORK ctrl_iface event and the user will need to explicitly
enable the network (e.g., with "select_network <id>") to connect to
the open network.
If the underlying driver supports off-channel TX, it will now be used by
the nl80211 driver wrapper, setting WPA_DRIVER_FLAGS_OFFCHANNEL_TX
accordingly.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
With the new kernel functionality coming to Linux to allow off-channel
TX, we can take advantage of that in the P2P code that currently uses
remain-on-channel. If a driver advertises support for it, it will be
asked to handle off-channel TX by itself.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The nl80211 driver can report low ACK condition (in fact it reports
complete loss right now only). Use that, along with a config option, to
disconnect stations when the data connection is not working properly,
e.g., due to the STA having went outside the range of the AP. This is
disabled by default and can be enabled with disassoc_low_ack=1 in
hostapd or wpa_supplicant configuration file.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
ClientTimeout changes from EAP peer methods were not supposed to
change behavior for other EAP peer methods or even other sessions
of the same method. Re-initialize ClientTimeout whenever an EAP
peer method is initialized to avoid this. This addresses problems
where WPS (EAP-WSC) reduces the timeout and consecutive EAP runs
may fail due to too small timeout.
If the peer you want to connect to is no longer available (does not
acknowledge frames) when wpa_supplicant sends GO Negotition Request
frames, retransmission of this frame is done until the associated
p2p_device structure is removed on timeout. In that case, no signal
is emitted to inform the GO Negotiation has failed.
When sending an Invitation Request frame, the same retransmission
mechanism is in place but limit the transmission to 100 and hitting
the limit generates an event.
This patch adds the same mechanism as the one in place for Invitation
Request, but with limit of 120 to match the existing wait_count for
for GO Negotiation.
If a station received unprotected Deauthentication or Disassociation
frame with reason code 6 or 7 from the current AP, there may be a
mismatch in association state between the AP and STA. Verify whether
this is the case by using SA Query procedure. If not response is
received from the AP, deauthenticate.
This implementation is only for user space SME with
driver_nl80211.c.
Some new code will require access to P2P group members, so add API to
retrieve the number of members and iterate the members themselves.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
If there is a pending GO Negotiation when p2p_cancel is used,
unauthorize the peer to avoid immediate reconnection from being
accepted without a new p2p_connect command.
This can be used by external programs (e.g., wlantest_cli) to inject
raw frames (hex dump of the frame header and body). The data can be
requested to be sent as-is or protected with the current key.
Previously, pairwise and group cipher suites were configured only
when kernel SME (nl80211 connect API) was used. However, mac80211
needs this information even in the user space SME case for one
thing: to disable HT when TKIP/WEP is used. Add
NL80211_ATTR_CIPHER_SUITES_PAIRWISE to fix this special case with
user space SME. This allows mac80211 to disable HT properly when
the AP is configured with configuration that is not allowed.
This add preliminary code for setting the per-STA RX GTK for
RSN IBSS when nl80211 drivers. For some reason, this does not
seem to fully work, but at least driver_nl80211.c is now aware of
what kind of key is being set and the whatever is missing from
making this key configuration go through should be specific to
nl80211/cfg80211.
The frame needs to be sent from an individual (non-group) address,
so drop invalid frames before sending Deauth/Disassoc frames to
not associated STAs.
One of the pointers to the PAC buffer was not updated after realloc
and if the realloc ended up returning new pointer, the *pos pointer
was still pointing at the old location (i.e., freed memory at
this point).
When controlling multiple virtual interfaces on the same physical
radio, share the scan results events with sibling interfaces. This
decreases the time it takes to connect many virtual interfaces.
This is currently only supported on Linux with cfg80211-based
drivers when using nl80211 or wext driver interface.
Signed-off-by: Ben Greear <greearb@candelatech.com>
Some drivers are not providing exactly reliable error codes (e.g.,
with WEXT), but others may actually indicate reliable information.
Allow driver wrappers to indicate if that is the case and use
optimizations if so. For now, this improves nl80211 with
NL80211_CMD_CONNECT for a case where connection request fails.
driver_param=use_p2p_group_interface=1 can now be used to test
nl80211-drivers with separate P2P group interface. In other words,
the main interface (e.g., wlan0) is reserved for P2P management
operations and non-P2P connections and a new group interface (e.g.,
p2p-wlan0-0) is created for the P2P group.
This implementation is very minimal, i.e., it only support address
allocation for a single P2P group interface (if the driver does not
handle this internally). In addition, not all functionality has yet
been tested, so for now, this is disabled by default and needs that
special driver_param to enable.
WPA_DRIVER_FLAGS_P2P_MGMT_AND_NON_P2P flag can now be used to
indicate that the initial interface (e.g., wlan0) is used for
P2P management operations and potentially non-P2P connections.
This is otherwise identical to
WPA_DRIVER_FLAGS_P2P_DEDICATED_INTERFACE, but the possibility of
non-P2P connections makes some operations differ.
Getting rid of these inline functions seems to reduce the code size
quite a bit, so convert the most commonly used hostapd driver ops to
function calls.
This is not needed anymore and just makes things more difficult
to understand, so move the remaining function pointers to direct
function calls and get rid of the struct hostapd_driver_ops.
send_eapol, set_key, read_sta_data, sta_clear_stats,
set_radius_acl_auth, set_radius_acl_expire, and set_beacon
to use inline functions instead of extra abstraction.
Commit bf65bc638f started the path to
add this new abstraction for driver operations in AP mode to allow
wpa_supplicant to control AP mode operations. At that point, the
extra abstraction was needed, but it is not needed anymore since
hostapd and wpa_supplicant share the same struct wpa_driver_ops.
Start removing the unneeded abstraction by converting
send_mgmt_frame() to an inline function, hostapd_drv_send_mlme().
This is similar to the design that is used in wpa_supplicant and
that was used in hostapd in the past (hostapd_send_mgmt_frame()
inline function).
driver.h defines these functions to return 0 on success, not
number of bytes transmitted. Most callers are checking "< 0" for
error condition, but not all. Address this by following the driver
API specification on 0 meaning success.
On Linux, verify that the kernel entropy pool is capable of providing
strong random data before allowing WPA/WPA2 connection to be
established. If 20 bytes of data cannot be read from /dev/random,
force first two 4-way handshakes to fail while collecting entropy
into the internal pool in hostapd. After that, give up on /dev/random
and allow the AP to function based on the combination of /dev/urandom
and whatever data has been collected into the internal entropy pool.
wlan0: RADIUS No authentication server configured
MEMLEAK[0x999feb8]: len 1040
WPA_TRACE: memleak - START
[3]: ./hostapd(radius_msg_new+0x33) [0x8074f43]
radius_msg_new() ../src/radius/radius.c:117
[4]: ./hostapd() [0x806095e]
ieee802_1x_encapsulate_radius() ../src/ap/ieee802_1x.c:439
ieee802_1x_aaa_send() ../src/ap/ieee802_1x.c:1496
For example, this error occured when I used WPS hostapd without
"eap_server=1" definition in configuration file.
By default, make hostapd and wpa_supplicant maintain an internal
entropy pool that is fed with following information:
hostapd:
- Probe Request frames (timing, RSSI)
- Association events (timing)
- SNonce from Supplicants
wpa_supplicant:
- Scan results (timing, signal/noise)
- Association events (timing)
The internal pool is used to augment the random numbers generated
with the OS mechanism (os_get_random()). While the internal
implementation is not expected to be very strong due to limited
amount of generic (non-platform specific) information to feed the
pool, this may strengthen key derivation on some devices that are
not configured to provide strong random numbers through
os_get_random() (e.g., /dev/urandom on Linux/BSD).
This new mechanism is not supposed to replace proper OS provided
random number generation mechanism. The OS mechanism needs to be
initialized properly (e.g., hw random number generator,
maintaining entropy pool over reboots, etc.) for any of the
security assumptions to hold.
If the os_get_random() is known to provide strong ramdom data (e.g., on
Linux/BSD, the board in question is known to have reliable source of
random data from /dev/urandom), the internal hostapd random pool can be
disabled. This will save some in binary size and CPU use. However, this
should only be considered for builds that are known to be used on
devices that meet the requirements described above. The internal pool
is disabled by adding CONFIG_NO_RANDOM_POOL=y to the .config file.
This commit adds a new wrapper, random_get_bytes(), that is currently
defined to use os_get_random() as is. The places using
random_get_bytes() depend on the returned value being strong random
number, i.e., something that is infeasible for external device to
figure out. These values are used either directly as a key or as
nonces/challenges that are used as input for key derivation or
authentication.
The remaining direct uses of os_get_random() do not need as strong
random numbers to function correctly.
This adds more time for the system entropy pool to be filled before
requesting random data for generating the WPA/WPA2 encryption keys.
This can be helpful especially on embedded devices that do not have
hardware random number generator and may lack good sources of
randomness especially early in the bootup sequence when hostapd is
likely to be started.
GMK and Key Counter are still initialized once in the beginning to
match the RSN Authenticator state machine behavior and to make sure
that the driver does not transmit broadcast frames unencrypted.
However, both GMK (and GTK derived from it) and Key Counter will be
re-initialized when the first station connects and is about to
enter 4-way handshake.
The example GMK-to-GTK derivation described in the IEEE 802.11 standard
is marked informative and there is no protocol reason for following it
since this derivation is done only on the AP/Authenticator and does not
need to match with the Supplicant. Mix in more data into the derivation
process to get more separation from GMK.
The previous commit broke completion in various places. The proper
way of handling the completion of full word is to verify whether
there are more than one possible match at that point.
Completion needs to be done even if the full word has been entered.
In addition, fix the space-after-full-word to properly allocate room
for the extra character when completion is used in the middle of the
string.
This adds new commands for wlantest_cli to request wlantest to
inject frames. This version can only send out Authentication
frames and unprotected SA Query Request frames, but there is
now place to add more frames and encryption with future commits.
ap_setup_locked=2 can now be used to enable a special mode where
WPS ER can learn the current AP settings, but cannot change then.
In other words, the protocol is allowed to continue past M2, but
is stopped at M7 when AP is in this mode. WPS IE does not
advertise AP Setup Locked in this case to avoid interoperability
issues.
In wpa_supplicant, use ap_setup_locked=2 by default. Since the AP PIN
is disabled by default, this does not enable any new functionality
automatically. To allow the read-only ER to go through the protocol,
wps_ap_pin command needs to be used to enable the AP PIN.
There is no point in maintaining two almost identical versions
of this parser. Move WPA IE parser into wpa_common.c similarly
to what was already the case with RSN IE parse.
When multiple wireless interfaces are used with WPS, the UPnP
subscriptions need to be removed whenever a matching Registrar
instance gets removed. This avoids a segfault due to access to
freed memory during hostapd shutdown.
In addition, the UPnP interface instance structure needs to be
freed to avoid memory leak.
WPS external Registrars can get confused about multiple UPnP
instances (one per radio) on a dual-concurrent APs. Simplify the
design by sharing a single UPnP state machine for all wireless
interfaces controlled by hostapd. This matches with the previous
changes that made a single command enable WPS functionality on
all interfaces.
This is relatively minimal change to address the sharing of the
state among multiple struct hostapd_data instances. More cleanup
can be done separately to remove unnecessary copies of information.
When the peer does not include our initial preference in the Channel
List attribute during GO Negotiation, try to use the best channel of
the other band as the new preference instead of falling back to the
first channel in the intersection.
The driver wrapper may now indicate the preferred channel (e.g., based
on scan results) on both 2.4 GHz and 5 GHz bands (and an overall best
frequency). When setting up a GO, this preference information is used
to select the operating channel if configuration does not include
hardcoded channel. Similarly, this information can be used during
GO Negotiation to indicate preference for a specific channel based
on current channel conditions.
p2p_group_add command can now use special values (freq=2 and freq=5)
to indicate that the GO is to be started on the specified band.
Commit d8d940b746 introduced a regression
that prevented TSN APs from being used with WEP since the AP was
rejected if it advertised WPA or RSN IE when we were configured to use
WEP. Resolve this by checking whether the AP is advertising a TSN, i.e.,
whether the AP allows WEP to be used as a group cipher. If so, allow
the AP to be selected if we are configured to use static WEP or
IEEE 802.1X (non-WPA).
It should be noted that this is still somewhat more restricted in AP
selection than earlier wpa_supplicant branches (0.7.x or older) that
ignore the WPA/RSN IE completely when configured for non-WPA.
This tool can be used to capture IEEE 802.11 frames either from a
monitor interface for realtime capturing or from pcap files for
offline analysis. This version is only adding basic infrastructure for
going through the frames and parsing their headers.
Commit c3fc47ea8e fixed EAP passthrough
server to allow Logoff/Re-authentication to be used. However, it
broke EAP standalone server while doing that. Fix this by reverting
the earlier fix and by clearing the EAP Identity information in the
EAP server code whenever an EAPOL-Start or EAPOL-Logoff packet is
received.
We need to drop the pending frame to avoid issues with the new GO
Negotiation, e.g., when the pending frame was from a previous attempt at
starting a GO Negotiation.
These are not used by any driver wrapper, i.e., only the four
data queues (BK, BE, VI, VO) are configurable. Better remove these
so that there is no confusion about being able to configure
something additional.
Pass data frames from unknown STAs to hostapd in order to reply with
a Deauthentication or Disassociation frame. This fixes compliance
with IEEE Std 802.11-2007, 11.3.
Furthermore, this does not cause a lot of overhead (at least with
mac80211 drivers) since mac80211 does not pass all data frames (but
at least from unauthenticated and unassociated STAs) to cooked monitor
interfaces.
Tested with rt2800pci on a MIPS board.
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
drivers.mak is shared between hostapd and wpa_supplicant and
compiling them together may create "wrong" flags.
Signed-off-by: Dmitry Shmidt <dimitrysh@google.com>
We are not actually interested in the PD Response in join-a-group
case, so there is no point in trying to send PD Request until the
response is received. This avoids an extra PD getting started after
a join-a-group operation in some cases.
This is needed to avoid problems with other applications setting and
leaving the interface to IF_OPER_DORMANT state. In AP mode, the interface
is ready immediately after the keys are set, so we better make sure the
DORMANT state does not prevent normal operations after that.
This is needed to avoid issues with APs that restart their UPnP,
e.g., when ER reconfigures them. The previously known settings are
now cached and taken into use if an AP is detected to leave
(ssdp:byebye) and then return.
Verify that the UUID given to wps_er_pbc command is known and only
activate PBC mode on the matching AP. The UUID can be that of the
AP or the station/Enrollee.
Add a new driver event, EVENT_INTERFACE_UNAVAILABLE, for indicating
that the driver is not able to continue operating the virtual
interface in its current mode anymore, e.g., due to operating
channel for GO interface forced to a DFS channel by another virtual
interface.
When this happens for a P2P group interface, the P2P group will
be terminated and P2P-GROUP-REMOVED event shows the reason for
this as follows:
P2P-GROUP-REMOVED wlan0 GO reason=UNAVAILABLE
A new configuration parameter, p2p_group_idle, can now be used to set
idle timeout value for P2P groups in seconds (0 = no timeout). If set,
this values is used to remove P2P group (both GO and P2P client)
interfaces after the group has been idle (no clients/GO seen) for the
configuration duration.
The P2P-GROUP-REMOVED event is now indicating the reason for group
removal when known. For example:
P2P-GROUP-REMOVED wlan0 GO reason=REQUESTED
P2P-GROUP-REMOVED wlan1 client reason=IDLE
Some driver wrappers may end up indicating a disassociation or
deauthentication event without the address of the station, e.g.,
based on a previous non-AP mode event. Avoid crashing hostapd
by verifying that the require address parameter is available in
the event before processing it.
In order to avoid confusing the driver with a new remain-on-channel
request, delay sending of a new Action frame if the driver indicates
Action frame RX diromg a scan.
This is needed to optimize response to GO Negotiation Request frames.
The extra remain-on-channel cancel followed by new remain-on-channel for
the same channel takes too much time with some driver/firmware
designs for the response to go out quickly enough to avoid peer
timing out while waiting for our response.
This command can be used to enroll a network based on a local
network configuration block instead of having to (re-)learn the
current AP settings with wps_er_learn.
This test command is supposed to change the WPS version number in all
places immediately, so make sure that the IEs used in management
frames get updated immediately.
The P2P group component is now tracking of associated stations
in the group and the Group Limit bit in the Group Capabilities
is updated based on whether there is room for new clients in
the group.
The workaround to ignore no ctrl::ack received for GO Negotiation
Confirmation frame was only supposed to be used when the frame was
actually transmitted and just the ack was not received. However, due
to the way the driver failure on transmitting the frame were reported,
this ended up getting applied for all failures in sending the GO
Negotiation Confirmation frame.
Improve this by providing a mechanism to indicate whether send_action
operations fail locally before the frame was actually transmitted or
because of not receiving ack frame after having transmitted the frame.
UPnP event subscriptions are not supposed to be dropped based on
whether events can be delivered quickly enough. Leave dropping to
happen only based on failed deliveries to avoid issues with a burst
of events kicking out still active subscribers.
Do not send more than five Probe Request WLANEvent notifications
per second. Even though the limit should in theory apply to all
WLANEvents, it is better not to drop EAP notifications because
of Probe Request frames and really, the only real reason for
event bursts is Probe Request frames.
Instead of queuing all events for a subscriber, only queue more
important events if delivery of event notifications starts failing.
This allows more time for the subscriber to recover since the maximum
queue length if not reached because of Probe Request frames only.
Instead of dropping the subscription on first failure, allow up to
10 failures before dropping. In addition, drop the callback URLs
one by one instead of full subscription if only one URL is failing.
If CONFIG_DRIVER_WEXT=y is not used in .config, but driver_wext.c
gets pull in to help another driver wrapper, rfkill code needs to
included to fix the build.
Listen to regulatory event messages from kernel and convert them to
internal driver event notifications indicated that the channel list
may have changed.
The AP operation with wpa_supplicant requires an additional callback
to get the needed event information from hostapd side so that
wpa_msg() can be called for wpa_s->parent if needed.
This makes it easier to figure out what could have failed in the
WPS protocol and potentially provide more information for the
user on how to resolve the issue.
The driver wrapper can now indicate whether the driver supports
concurrent operations on multiple channels (e.g., infra STA connection
on 5 GHz channel 36 and P2P group on 2.4 GHz channel 1). If not,
P2P_CONNECT commands will be rejected if they would require
multi-channel concurrency.
The new failure codes for P2P_CONNECT:
FAIL-CHANNEL-UNAVAILABLE:
The requested/needed channel is not currently available (i.e., user has
an option of disconnecting another interface to make the channel
available).
FAIL-CHANNEL-UNSUPPORTED:
The request channel is not available for P2P.
At least D-Link DIR-600 and DIR-825 have been reported to include
an extra octet after the Network Key attribute within a Credential
attribute. This can happen at least when they are provisioning an
open network.
Add a workaround to detect this incorrectly encoded attribute and
to skip the extra octet when parsing such a Credential.
The new nl80211 API means we don't need to use monitor interfaces. This
means that the P2P implementation now requires a kernel that has support
for generic management frame (not just Action frame) transmission.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This is backward compatible since older kernels will ignore the extra
attribute and only allow registration for Action frames.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
libnl has a bug, when binding more than two sockets and releasing one,
it will release the wrong address and then try to reuse it, which fails.
Therefore, we need to reimplement the socket address assignment logic
locally for libnl 1.1.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Some sequencies of EAPOL logoff/logon/start messages seem to be
able to get the previous implementation into state where hostapd
would not be able to start reauthentication when external
authentication server is used. The EAP server code would bypass
the initial Identity Request generation and EAPOL code would not
be able to send anything to the authentication server or supplicant
at that point. Work around this by forcing EAP server code to
start with Identity Request after INITIALIZE state even if the
Identity is known.
When a single hostapd process is controlling multiple interfaces,
apply the received or auto-generated configuration changes to all
interfaces that have enabled WPS.
When the same hostapd process is controlling multiple interfaces,
apply WPS commands (push button, add PIN, change AP PIN) to all
interfaces that are configured to use WPS.
A separate build number (etc.) version number postfix can now be
added to the build without having to modify source code files by
defining VERSION_STR_POSTFIX. This can be done, e.g., by adding
following line to .config:
CFLAGS += -DVERSION_STR_POSTFIX=\"-foo\"
Commit 3379a3a795 added a direct
iface->for_each_interface use without verification whether the
function is available. This works with hostapd, but not
wpa_supplicant (which crashes on segfault).
The previous implementation ended up incorrectly assuming that all
40 MHz use cases have secondary channel above the primary one. Fix this
by properly masking the secondary channel offset field and checking its
value.
wpa_supplicant showed signal levels incorrectly with some drivers:
Jun 6 16:29:36 rupert wpa_supplicant[18945]: Current BSS: 00:0d:97:11:40:d6
level=190
Jun 6 16:29:36 rupert wpa_supplicant[18945]: Selected BSS: 00:0d:97:11:50:09
level=192
Judging from output from other tools (iwlist) and the min_diff block
at the end of wpa_supplicant_need_to_roam, it seems these values
should actually be negative. Specifically, if one treats that number
as a signed char instead of unsigned, everything matches up.
To be honest, I've little to no understanding of wireless, but looking
at the source code for wireless-tools (iw_print_stats in iwlib.c), it
seems that the fields of the iw_quality struct need to be decoded
differently depending on various flags. I guess
src/drivers/driver_wext.c should have similar logic in
wext_get_scan_qual.
I wrote a patch that attempts to replicate some of that logic,
although it may be more complicated than is necessary; I think some of
the complexity is for backwards-compatibility, which might not be
necessary depending on wpa_supplicant's dependencies? In any case, it
is attached. Again, I don't know how any of this works, so it's likely
the patch is a bit off. But I think at least the logic to determine
min_diff in wpa_supplicant_need_to_roam would be more accurate if
level were determined correctly.
We need to clear the selected registrar timeout from wps_er_learn
when stopping the protocol run at M7 (previously, this was done only
when WSC_Done was being processed). In addition, we need to cancel
the timeout when a new PBC operation is started.
This is needed to update the pointers maintained within WPS code
to use the new configuration data instead of maintaining pointers
to the old configuration which will be freed. This fixes strings in
UPnP discovery after reconfig (they used to be random freed memory..).
Need to figure out whether the message is from a WSC 2.0 -based
device based on the unencrypted attributes, not the contents of the
encrypted data since the Version2 subelement is only included in the
unencrypted area.
This seems to be the easiest way of making sure the Config Methods
value is compliant with the WSC 2.0 specification without having
to modify the configuration file. However, this will only add the
virtual flag, so the configuration files should really be updated
to specify values that match the AP design.
WPS 2.0 mandates the AP to include WPS IE in (Re)Association Response
if the matching (Re)Association Request included WPS IE. Provide the
needed WPS IE information to the driver_ops API for drivers that
process association frames internally.
Note: This modifies the driver_ops API by adding a new argument to
set_ap_wps_ie().
Instead of build time options (CONFIG_WPS_TESTING_EXTRA_CRED and
CONFIG_WPS_EXTENSIBILITY_TESTING), use a single build option
(CONFIG_WPS_TESTING) and runtime configuration of which testing
operations are enabled. This allows a single binary to be used
for various tests.
The runtime configuration can be done through control interface
with wpa_cli/hostapd_cli commands:
Enable extensibility tests:
set wps_version_number 0x57
Disable extensibility tests (WPS2 build):
set wps_version_number 0x20
Enable extra credential tests:
set wps_testing_dummy_cred 1
Disable extra credential tests:
set wps_testing_dummy_cred 0
If the peer is not authorized for GO Negotiation, wps_method is not
actually set. In that case, it is better to fill in our default
config methods rather than end up leaving the field to be zero.
The Beacon frame must include UUID-E and RF Bands attributes when
in active PBC mode to allow stations to figure out that two BSSes in
PBC mode is not a PBC session overlap.
When generating the UUID based on MAC address, share the same UUID
with all interfaces. This fixes a potential issue with concurrent
dualband APs where the UUID needs to be same for PBC to work properly.
If the msg->device_name buffer is filled from two different sources,
the copy from the P2P Device Info attribute needs to make sure that
the values gets null terminated to match the length of the correct
string should the other place use another string (which is not really
allowed by the spec, but could happen).
A new ctrl_interface command, WPS_CANCEL, can now be used to cancel
a pending or ongoing WPS operation. For now, this is only available
with wpa_supplicant (either in station or AP mode). Similar
functionality should be added for hostapd, too.
If an authorized (p2p_connect used locally) GO Negotiation is
rejected when receiving GO Negotiation Request from the peer,
indicate the failure with a ctrl_interface P2P-GO-NEG-FAILURE
event. Previously, this event was only shown on the peer (i.e.,
the device receiving the GO Negotiation Response with non-zero
Status code).
Since this message now includes P2P Device Info attribute, it is
reasonable to learn the peer data and process the message instead of
rejecting the message.
Add (or complete Probe Request only) P2P peer entry when receiving
Provision Discovery Request from a previously unknown peer. This is
especially of use for a GO when a P2P client is requesting to join
a running group.
The scan operation before Provision Discovery Request may not include
the GO. However, we are likely to have the GO in our P2P peer table,
so use that information to figure out the operating channel if BSS
table entry is not available.
This should not really happen, but it looks like the Listen command
may fail is something else (e.g., a scan) was running at an
inconvenient time. As a workaround, allow new Extended Listen
operation to be started if this state is detected.
The previous version had a bug that could result in NULL pointer
dereference if the P2P IE included Manageability attribute, but no
Capability attribute.
This can happen, e.g., when a P2P client connects to a P2P group
using the infrastructure WLAN interface instead of P2P group
interface. In that case, the P2P client may behave as if the GO
would be a P2P Manager WLAN AP.
This is needed to be able to change parameters for dynamically
created interfaces between the creation of the interface and
association/start AP commands.
Following ctrl_interface commands can now be used:
P2P_SET client_apsd disable
- disable configuration (i.e., use driver default) in client mode
P2P_SET client_apsd <BE>,<BK>,<VI>,<VO>;<max SP Length>
- enable UASPD with specific trigger configuration (0/1) per AC
(max SP Length is currently ignored)
P2P_SET go_apsd disable
- disable configuration (i.e., use driver default) in AP mode
P2P_SET go_apsd <0/1>
- disable/enable APSD in AP mode
P2P specification v1.15 fixed the description of the GAS fragmentation
to not duplicate NQP Query Response Field header in all fragments. This
change makes the fragmentation match with the description in IEEE
802.11u. The change is not backwards compatible with previous P2P
specification versions as far as fragmented SD responses are concerned.
This event indicates the Device Password ID that the peer tried
to use in GO Negotiation. For example:
P2P-GO-NEG-REQUEST 02:40:61:c2:f3:b7 dev_passwd_id=4
If enabled, cross connection allows GO to forward IPv4 packets
using masquerading NAT from the P2P clients in the group to an
uplink WLAN connection. This is disabled by default and can be
enabled with "wpa_cli p2p_set cross_connect 1" on the P2P device
interface.
When we receive Device Discoverability Response, we need to initiate
new GO Negotiation as quickly as possible to avoid the target client
from going back to sleep. Make sure we do not end up in
P2P_CONNECT_LISTEN state (short Listen mode) in this case.
For now, this applies to the test command that can be used to set
periodic NoA (p2p_set noa). The value are stored and periodic NoA
is enabled whenever there are no non-P2P STAs connected to the GO.
While this is not strictly speaking required by the P2P specification
for a not-P2P Managed Device, this can provide useful information for
the P2P manager AP and may be needed to pass certification tests.
While there is no real value in this, the spec seems to mark this
attribute as mandatory from GO, so better included it regardless
of whether we have clients or not (the attribute is empty in case
no clients are connected).
"wpa_cli p2p_set peer_filter <MAC address>" can now be used to
only allow a single P2P Device (based on P2P Device Address) to be
discovered for testing. Setting the address to 00:00:00:00:00:00
disables the filter.
The WSC 2.0 specification moved to use another design for the new
attributes to avoid backwards compatibility issues with some
deployed implementations.
If CONFIG_WPS_STRICT is set, validate WPS IE(s) in management frames and
reject the frames if any of the mandatory attributes is missing or if an
included attribute uses an invalid value. In addition, verify that all
mandatory attributes are included and have valid values in the WSC
messages.
If all the device information attributes use their maximum lengths,
a single WPS IE is not enough to fit in all the data and as such,
we must be able to fragment the data. In addition, the wpabuf needs
to be allocated larger to fit in maximum data.
Instead of using 0x00 as the extra character, use space (' ') to
avoid failing tests that verify that the variable length string
attributes are not null terminated. In addition, this workaround
can now be disabled by defining CONFIG_WPS_STRICT for the build.
This can be done by adding following line to .config:
CFLAGS += -DCONFIG_WPS_STRICT
However, it should be noted that such a build may not interoperate
with some deployed WPS 1.0 -based implementations and as such, is
mainly designed for testing.
Whenever wpa_supplication is using Request Type Enrollee, it is trying
to enroll into a network. Indicate this with the explicit inclusion of
Request to Enroll attribute with value TRUE.
Advertize list of authorized enrollee MAC addresses in Beacon and
Probe Response frames and use these when selecting the AP. In order
to provide the list, the enrollee MAC address should be specified
whenever adding a new PIN. In addition, add UUID-R into
SetSelectedRegistrar action to make it potentially easier for an AP
to figure out which ER sent the action should there be multiple ERs
using the same IP address.
This adds definitions and parsing of the new attributes that were added
in WPS 2.0. In addition, the version negotiation is updated to use the
new mechanism, i.e., accept everything received and use the new Version2
attribute in transmitted messages.
While this is not strictly speaking required based on dynamic
configuration (i.e., dot11ShortPreambleOptionImplemented is static
value based on implementation, not runtime configuration), it is better
to follow local configuration parameter for short preamble in addition
to the associated station capabilities.
This function is not really needed in case of drivers that build the
HT IEs internally. However, since this can get called if ieee80211n=1
is set in hostapd.conf, we better not segfault even if the driver
does not provide hw info (hapd->iface->current_mode == NULL).
Commit 5a1cc30f1a added code that was
assuming CONFIG_WPS_UPNP is enabled whenever CONFIG_WPS is. Fix this
by making the UPnP calls conditional on CONFIG_WPS_UPNP define.
Prior to commit 6195adda9b the sm->user
dereference did not exist here. While this is in practice non-NULL,
better use more defensive construction here to avoid NULL pointer
dereference should this ever change.
Some NDIS drivers require a workaround to allow them to associate
with a WPS AP that is already using protection (Privacy field = 1).
Let driver_ndis.c know if the AP is already using Privacy and if so,
configure a dummy WEP key to force the driver to associate.
When using overlapped write, we must have the provided memory
areas available during the operation and cannot just use stack
unless we wait for the completion within the function. In the case
of TX here, we can easily wait for the completion since it is likely
to happen immediately. In addition, this provides more reliable
success/failure return value for l2_packet_send(). [Bug 328]
hostapd simply used its own STBC configuration in the STA's HT caps. This
resulted in TX STBC being used for STAs not supporting RX STBC, which in
turn resulted in the STA not receiving anything.
Fix this by handling the STBC flags in the same way mac80211 does. Mask
out RX STBC if we don't support TX STBC and vice versa.
Tested only with the nl80211 driver and a STBC incapable STA.
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
This patch adds support for wired IEEE 802.1X client on the Solaris.
I have tested with these:
OS : OpenSolaris 2009.06
EAP : EAP-MD5
Switch : Cisco Catalyst 2950
The arithmetic on void pointer exists in trace routine. On GNU C, it
works because void pointer size is 1, but not all compilers behave like
this. So this patch specifies the size of the pointer.
There is no need to process the public key and generate keys if
the AP is going to reject this M2 anyway. This limits effect of
potential CPU DoS attacks in cases where AP PIN is disabled.
A new hostapd_cli command, wps_ap_pin, can now be used to manage
AP PIN at runtime. This can be used to generate a random AP PIN and
to only enable the AP PIN for short period (e.g., based on user
action on the AP device). Use of random AP PIN that is only enabled
for short duration is highly recommended to avoid security issues
with a static AP PIN.
As a compromise between usability and security, do not disable
AP PIN permanently based on failed PIN validations. Instead, go to
AP Setup Locked state for increasing amount of time between each
failure to slow down brute force attacks against the AP PIN.
This avoids problems with some external Registrars that may try
to use the same PIN multiple times without user input. Now, the
user will still be able to fix the PIN and try again later while
a real attack is delayed enough to make it impractical.
This can happen on the AP if the AP PIN is not configured and
the client tries to go through the protocol instead of just using
Registrar mode to receive M1 from the AP. It is cleaner to send
out the WSC_NACK instead of just stopping the protocol.
This indicates that the peer identity is associated with the
credential and will be required to match with the identity used
during authentication when the PAC is used (RFC 5422, 4.2.4).
When passing several authentication algorithms through auth_alg, we
should try all of them when the first one fails. The wext driver goes
through the connect nl80211 command and the retries are then handled by
the kernel. The nl80211 doesn't and we have to handle that from
userspace.
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
DEAUTH messages can come from a number of different sources. The one
that's hurting us currently is DEAUTH netlink messages coming to us
from compat-wireless in response to local_state_change DEAUTH messages
we sent as a part of cleaning up state in driver_nl80211's
clear_state_mismatch() function. However, DEAUTH messages can come
from a variety of unwanted sources, including directed denial-of-service
attacks (although MAC verification doesn't place that high a barrier),
so this validation is actually generically useful, I think.
The downside to this method is that without a kernel based approach
"iw dev wlan0 link" no longer works correctly after clear_state_mismatch()
is done. This will be pursued with the kernel folks.
cfg80211/mac80211 seems to be unwilling to change interface mode in
some cases. Make these less likely to cause problems by trying the
changes up to 10 times with 100 msec intervals.
In theory, this should not really be needed, but Windows 7 uses
Registrar mode to probe AP's WPS capabilities before trying to use
Enrollee and fails if the AP does not allow that probing to happen.
This allows the AP to start as an Enrollee and send M1, but refuse
to continue beyond that (M3 will not be sent if AP PIN is not known).
This makes it easier (and a bit faster) to handle multiple local
radios with FT. There is no need to depend on l2_packet in that
case since the frame can be delivered as a direct function call.
If the station does not include WSC IE in Association Request, it
is marked with WLAN_STA_MAYBE_WPS flag. We can update that to
WLAN_STA_WPS if the station uses either of the WPS identity strings.
This enables some workarounds for WPS stations.
This works around issues with EAP-Failure getting lost for some reason.
Instead of waiting up to 60 seconds on a timeout, 30 second timeout is
now used and whenever the provisioning step has been completed (either
successfully or unsuccessfully), this timeout is reduced to 2 seconds.
The pairwise cipher field is supposed to be little endian, but the
message building functions did not swap the bytes on big endian
hosts while the message processing functions did. Fix this by using
little endian byte order in both places.
It looks like 10.6.3 and 10.6.4 do not like to receive Network Key
with WPA passphrase while PSK format still works. Use peer information
from M1 to figure out whether the Enrollee is likely to be OS X and
if so, force PSK format to be used for Network Key.
Some frequent debug prints are of limited use and make debug output
difficult to read. Make them use a new debug level so that -dd
provides more readable output (-ddd can now be used to enable
the excessive debug prints).
The length of the prime was used incorrectly and this resulted
in WPS DH operation failing whenever the public key ended up having
leading zeros (i.e., about every 1/256th time).
The AP configuration may change after provisioning, so it is better
not to use the current security policy to prioritize results. Instead,
use WPS Selected Registrar attribute as the main sorting key and use
signal strength next without considering security policy or rate sets.
The non-WPS provisioning case remains as-is, i.e., this change applies
only when trying to find an AP for WPS provisioning.
Some deployed implementations do not include the mandatory Network
Key attribute when a WPS Credential is for an open network. Allow
this to improve interoperability since the actual key value is not
really needed for open networks.
Replace use of rfkill block event with rtnetlink ifdown. This makes
the design more robust since the rfkill event could have been for
another interface while the rtnetlink events are already filtered
based of ifindex. In addition, the new design handles other than
rfkill-triggered ifdown/ifup events, too. rfkill unblocked event
is still needed to try to set the interface back up. If the unblock
was for another interface, ifup will fail and the driver state is
not changed.
Some of the driver wrappers need to get set_ieee8021x() call before
they can configure keys. Reorder the operations in the reloading
of configuration case to match with that expectation.
Setting IEEE80211_PARAM_AUTHMODE to IEEE80211_AUTH_AUTO ends up enabling
Privacy mode in the driver. We need to clear that to allow hostapd to be
reconfigured into open mode.
wps_er_config can now be used to configure an AP. It is similar to
wps_er_learn, but instead of only learning the current AP settings,
it continues to send M8 with the new settings for the AP.
wps_er_start command now takes an optional parameter that can be used
to configure a filter to only allow UPnP SSDP messages from the
specified IP address. In practice, this limits the WPS ER operations
to a single AP and filters out all other devices in the network.
When starting the protocol run with an Enrollee, clone the AP Settings
and replace the AP MAC Address with the Enrollee MAC Address so that the
correct value is then used in the Credential attribute in M8.
If the associating station indicates that it is intents to use WPS
by including WPS IE in (Re)Association Request frame, include WPS IE
in (Re)Association Response frame.
There may be more than one attribute of same type (e.g., multiple DC
attributes), so the code needs to be able to handle that. Replace the
fixed structure with an array of attributes.
Previous version driver_bsd.c switches the channel in
wpa_driver_bsd_associate(). This patch changes it to use set_freq().
I have tested this patch on FreeBSD 8.0/NetBSD 5.0.2 with hostapd,
wpa_supplicant(AP) and wpa_supplicant(STA).
Add a new wpa_supplicant state: interface disabled. This can be used
to allow wpa_supplicant to be running with the network interface even
when the driver does not actually allow any radio operations (e.g.,
due to rfkill).
Allow driver_nl80211.c and driver_wext.c to start while rfkill is in
blocked state (i.e., when ifconfig up fails) and process rfkill
events to block/unblock WLAN.
Vendor-specific IEs are supposed to be in the end of the frame, so move
WMM into the end of Beacon, Probe Response, and (Re)Association Response
frames. In addition, move HT IEs to be later in (Re)Association
Response to match the correct order.
hostapd_eid_wpa() adds multiple IEs and the end result may not always be
correct. If WPA is enabled, WPA IE (vendor-specific) gets added in the
middle of the frame and not in the end. This would require a larger
change to spliut the IEs from WPA module into separate locations when
constructing Beacon and Probe Response frames. This is not yet addressed.
Commit 83935317a7 added forced
disconnection in case of 4-way handshake failures. However, it should
not have changed the case where the supplicant is requesting fallback
to full EAP authentication if the PMKID in EAPOL-Key message 1/4 is
not know. This case needs to send an EAPOL-Start frame instead of
EAPOL-Key message 2/4.
This works around a problem with APs that try to force PMKSA caching
even when the client does not include PMKID in (re)association request
frame to request it. [Bug 355]
Commit c02d52b405 removed direct calls
to the WPA authenticator, but the change here was incorrect.
EAPOL_SM_USES_WPA was supposed to be set based on sta->wpa_sm being
set, i.e., no need to check for PMKSA entries for that.
While this could potentially change EAPOL Key TX state machine behavior,
no clear problems have been identified so far. Anyway, better fix this
to get the correct flags set for EAPOL authenticator state machine.
When using WPS, we may end up here if the STA manages to re-associate
without the previous STA entry getting removed. Consequently, we need to
make sure that the WPA state machines gets initialized properly at this
point.
62477841a1 tried to address fragmentation
issues, but it did not address the case where the final EAP-TNC
message gets fragmented. Move the state update to the correct place
to address this case, too.
There are no subdirectories in any of these directories or plans
for adding ones. As such, there is no point in running the loop
that does not do anything and can cause problems with some shells.
Both the wildcard VLAN entry and the statically configured VLAN
interfaces should behave in the same way. Initializing the
full dynamic VLAN code before adding the statically configured VLAN
interfaces allows the same processing to be applied to both statically
and dynamically added VLAN interface (i.e., also the statically
configured ones will be added to a bridge).
The WPS IE was overriding the WPA/RSN IE in driver based MLME case
(hostapd_notif_assoc), but the MLME code here was not using WPS IE
correctly, i.e., it allowed the WPA/RSN IE override the operation.
The returned buffer length was hardcoded to be the prime length
which resulted in shorter results being padded in the end. However,
the results from DH code are supposed to be unpadded (and when used
with WPS, the padding is done in WPS code and it is added to the
beginning of the buffer). This fixes WPS key derivation errors
in about 1/256 of runs ("WPS: Incorrect Authenticator") when using
the internal crypto code.
This adds more details into the CTRL-EVENT-DISCONNECTED event to
make it easier to figure out which network was disconnected in some
race conditions and to what could have been the reason for
disconnection. The reason code is currently only available with
the nl80211 driver wrapper.
There is no absolute requirement for separating address allocation
into separate functions, so simplify the driver wrapper interface
to use just if_add and if_remove instead of adding the new
alloc_interface_addr() and release_interface_addr() functions.
if_add() can now indicate if the driver forced a different interface
name or address on the virtual interface.
The server may still reject authentication at this point, so better
use conditional success decision. This allows the potentially
following EAP-Failure message to be processed properly. [Bug 354]
hostapd does not implement UAPSD functionality. However, if U-APSD
functionality is implemented outside hostapd, add support to advertise
the functionality in beacon.
Signed-off-by: yogeshp@marvell.com
Instead of parsing the IEs in the callers, use the already existing
parser in wpa_ft.c to handle MDIE and FTIE from initial MD association
response. In addition, this provides more complete access to association
response IEs to FT code which will be needed to fix FT 4-way handshake
message 2/4.
ANonce, SNonce, R0KH-ID, and R1KH-ID must match with the values
used in the previous FT authentication sequence message per
IEEE Std 802.11r-2008, 11A.8.4.
This sets the FT Capability and Policy field in the MDIE to the values
received from the target AP (if available). This fixes the MDIE contents
during FT Protocol, but the correct value may not yet be used in initial
mobility domain association.
We do not have any keys set at this point so there is no point in
adding the MIC. In addition, IEEE Std 802.11r-2008, 11A.4.2
describes this frame to have MIC IE count of 0 and MIC of 0.
This removes transmission of some unnecessary Deauthentication
frames in cases where we only need to clear the local state. In
addition, this resolves issues for 802.11r FT-over-DS by allowing
authentication state to be set locally even when no actual
Authentication frame is to be transmitted.
IEEE Std 802.11r-2008, 11A.4.2 describes FT initial mobility domain
association in an RSN to include PMKR1Name in the PMKID-List field
in RSN IE in messages 2/4 and 3/4. This makes the RSN IE not be
bitwise identical with the values used in Beacon, Probe Response,
(Re)association Request frames.
The previous versions of wpa_supplicant and hostapd did not add the
PMKR1Name value in EAPOL-Key frame and did not accept it if added
(due to bitwise comparison of RSN IEs). This commit fixes the
implementation to be compliant with the standard by adding the
PMKR1Name value into EAPOL-Key messages during FT 4-Way Handshake and
by verifying that the received value matches with the value derived
locally.
This breaks interoperability with previous wpa_supplicant/hostapd
versions.
Running hostapd and wpa_supplicant on the same interface at the same
time is not expected to work, but it should not cause hostapd to crash.
Ignore station mode association events (no addr field) to avoid this.
IF WPA/RSN parameters were changed or WPA/RSN was disabled, the
WPA/RSN IE in Beacon/Probe Response frames was only update with
set_beacon(). We need to do this with set_generic_elem(), too, to
work with all driver wrappers.
Call ieee802_11_set_beacon() in addition to set_ap_wps_ie() when
processing WPS IE updates. This is needed with drivers that use
set_beacon() instead of set_ap_wps_ie() (i.e., nl80211).
Some ER implementation (e.g., some versions of Intel PROSet) seem to
use incorrect format for WLANEventMAC variable in PutWLANResponse.
Work around this by allowing various MAC address formats to be used
in this variable (debug message will be shown if the colon-deliminated
format specified in WFA WLANConfig 1.0 is not used).
This version of the MAC address parser allows number of different
string formats for the address (e.g., 00:11:22:33:44:55, 0011.2233.4455,
001122334455, 00-11-22-33-44-55). It returns the number of characters
used from the input string in case of success.
It turns out that this is needed for both FT-over-DS and FT-over-air
when using mac80211, so it looks easiest to just unconditionally
re-configure the keys after reassociation when FT is used.
This is needed to allow reassociation processing to skip 4-way handshake
when FT-over-DS is used with an AP that has a previous association state
with the STA.
This seems to be needed at least with mac80211 when a STA is using
FT-over-DS to reassociate back to the AP when the AP still has the
previous association state.
This makes the call simpler for driver wrappers since there is no need
to parse the IEs anymore before indicating association. In addition,
this allows association processing to be extended to use other IEs
in the future.
This avoids conflict with both Label and Display being included at
the same time (which would make it difficult to figure out which
PIN was actually used).
IGTK get_seqnum needs to be skipped in the same way as GTK one when
rekeying group keys. Previously, the old PN value (the one from the
previous key) was indicated and that resulted in MMIE replay detection
at the station.
This can be used to test 802.11w by sending a protected or unprotected
deauth/disassoc frame.
hostapd_cli deauth <dst addr> test=<0/1>
hostapd_cli disassoc <dst addr> test=<0/1>
test=0: unprotected
test=1: protected
Must update sm->pairwise when fetching PMK-R1 SA.
Add a workaround for drivers that cannot set keys before association
(e.g., cfg80211/mac80211): retry PTK configuration after association.
If the PTK configuration prior to association fails, allow reassociation
attempt to continue and configure PTK after association. This is a
workaround for drivers that do not allow PTK to be configured before
association (e.g., current cfg80211/mac80211).
This attribute is supposed to indicate which methods the AP supports as
an Enrollee for adding external Registrars. It was left to 0 when the
AP code did not yet support external Registrars and was forgotten when
the ER support was added.
On NetBSD 5.0.2, wpa_supplicant build results in messages below.
../src/drivers/driver_bsd.c: In function 'wpa_driver_bsd_get_ssid':
../src/drivers/driver_bsd.c:876: warning: passing argument 2 of 'bsd_get_ssid'
from incompatible pointer type
../src/drivers/driver_bsd.c:876: warning: passing argument 3 of 'bsd_get_ssid'
makes integer from pointer without a cast
../src/drivers/driver_bsd.c:876: error: too many arguments to function
'bsd_get_ssid'
../src/drivers/driver_bsd.c: In function 'wpa_driver_bsd_scan':
../src/drivers/driver_bsd.c:1125: warning: passing argument 2 of 'bsd_set_ssid'
from incompatible pointer type
../src/drivers/driver_bsd.c:1125: warning: passing argument 3 of 'bsd_set_ssid'
makes integer from pointer without a cast
../src/drivers/driver_bsd.c:1125: error: too many arguments to function
'bsd_set_ssid'
gmake: *** [../src/drivers/driver_bsd.o] Error 1
This patch solves this issue.
This is a step in adding FT support with nl80211-based drivers.
driver_nl80211.c is now registering to handle the FT Action frames
and is able to transmit FT Request frame. Received FT Action frames
are not yet indicated as driver events.
This is needed to fix PTK derivation to use correct length. Previously,
64-octet PTK may have been derived if the authenticator did not already
have a STA entry. Now, the correct pairwise cipher suite is learned when
then PMK-R1 SA is received.
This was not supposed to have duplicate value with WPA_AUTH_ALG_LEAP.
The previous version was unable to set FT as the authentication
algorithm with nl80211.
With this patch, a client gets kicked out of the last BSS it was
attached to, when it is associating to a different one.
While mac80211 does allow a station to be present on multiple bss
interfaces, this does seem to cause problems both for the stack
and for hostapd.
This patch allows the nl80211 driver to create its own per-bss context
and pass it to the drv_priv pointer of the hostapd bss state.
With this and the following patch, stations can associate to and switch
between multiple BSS interfaces of a single wiphy.
This obsoletes a few instances of passing ifname to a callback, those
can be removed in a separate patch.
It might also be useful to move more fields from the driver data to the
per-bss data structure in the future.
This patch allows wpa_supplicant to compile on Debian's kfreebsd
architectures.
Patch by Stefan Lippers-Hollmann based on work done by Petr Salinger
and Emmanuel Bouthenot for 0.6.X (http://bugs.debian.org/480572).
filter_ssids=1 global configuration parameter can now be used to
enable scan result filtering (with -Dnl80211 only for now) based on
the configured SSIDs. In other words, only the scan results that have
an SSID matching with one of the configured networks are included in the
BSS table. This can be used to reduce memory needs in environments that
have huge number of APs.
wpa_supplicant can now be notified of suspend/resume events, e.g.,
from pm-action scripts. This allows wpa_supplicant to clear information
that may become invalid during a suspend operation.
The kernel side support for this was just added into
wireless-testing.git. This commit adds the driver wrapper code needed
to allow wpa_supplicant to use the new functionality.
Some drivers may need to use a specific ifname for the virtual
interface, so allow them to do this with a new parameter passed
to the alloc_interface_addr() handler.
TNC IF-T is somewhat unclear on this are, but
draft-hanna-nea-pt-eap-00.txt, which is supposed to define the same
protocol, is clearer on the Flags field being included.
This change breaks interoperability with the old implementation if
EAP-TNC fragmentation is used. The old version would not accept
the acknowledgement message with the added Flags octet while the
new version accepts messagss with with both options.
If the last message from the EAP-TNC server was fragmented, the
fragment processing lost the DONE/FAIL state and did not know how
to handle the final ACK from the peer. Fix this by remembering the
earlier DONE/FAIL state when fragmenting a frame.
TNC IF-T specification is unclear on the exact contents of the fragment
acknowledgement frame. An interoperability issue with the tncs@fhh
implementation was reported by Arne Welzel
<arne.welzel@stud.fh-hannover.de> due to the different interpretations
of the specification. Relax EAP-TNC server/peer validation rules to
accept fragmentation acknowledgement frames to include the Flags field
to avoid this issue.
This patch aggregates ioctls.
First is SIOCS80211. The SIOCS80211's arguments has 3 couples.
1-1. i_len, i_data
1-2. i_val
1-3. i_len, i_data, i_val (currently only IEEE80211_IOC_APPIE)
There were 3 routines for each cases. This patch aggregates these to
one.
Second is SIOCG80211. The SIOCG80211 returns 2 type of value.
2-1. i_len
2-2. i_val
There were 2 routines for each cases. This patch aggregates these to
one.
I have tested on both FreeBSD 8.0 and NetBSD 5.0.1 with these cases.
[hostapd]
RSN-PSK(CCMP)/WPA-PSK(TKIP)
[wpa_supplicant(STA)]
RSN-PSK(CCMP)/WPA-PSK(TKIP)
[wpa_supplicant(AP)]
RSN-PSK(CCMP)/WPA-PSK(TKIP)
This patch enables FreeBSD channel control.
I have tested on FreeBSD 7.2 with these cases.
[hostapd]
RSN-PSK(CCMP)/WPA-PSK(TKIP)
[wpa_supplicant(STA)]
RSN-PSK(CCMP)/WPA-PSK(TKIP)
[wpa_supplicant(AP)]
RSN-PSK(CCMP)/WPA-PSK(TKIP)
The attached patch unifies hostapd wpa_driver_bsd_ops and
wpa_supplicant wpa_driver_bsd_ops.
I have tested on NetBSD 5.0.1 with these cases.
[hostapd]
RSN-PSK(CCMP)/WPA-PSK(TKIP)
[wpa_supplicant(STA)]
RSN-PSK(CCMP)/WPA-PSK(TKIP)
[wpa_supplicant(AP)]
RSN-PSK(CCMP)/WPA-PSK(TKIP)
This patch modifies field name of struct bsd_driver_data to use
same name of struct wpa_driver_bsd_data. This is a preparation of
unifying struct bsd_driver_data and struct wpa_driver_bsd_data.
This allows external programs (e.g., UI) to get more information
about server certificate chain used during TLS handshake. This can
be used both to automatically probe the authentication server to
figure out most likely network configuration and to get information
about reasons for failed authentications.
The follow new control interface events are used for this:
CTRL-EVENT-EAP-PEER-CERT
CTRL-EVENT-EAP-TLS-CERT-ERROR
In addition, there is now an option for matching the server certificate
instead of the full certificate chain for cases where a trusted CA is
not configured or even known. This can be used, e.g., by first probing
the network and learning the server certificate hash based on the new
events and then adding a network configuration with the server
certificate hash after user have accepted it. Future connections will
then be allowed as long as the same server certificate is used.
Authentication server probing can be done, e.g., with following
configuration options:
eap=TTLS PEAP TLS
identity=""
ca_cert="probe://"
Example set of control events for this:
CTRL-EVENT-EAP-STARTED EAP authentication started
CTRL-EVENT-EAP-PROPOSED-METHOD vendor=0 method=21
CTRL-EVENT-EAP-METHOD EAP vendor 0 method 21 (TTLS) selected
CTRL-EVENT-EAP-PEER-CERT depth=0 subject='/C=US/ST=California/L=San Francisco/CN=Server/emailAddress=server@kir.nu' hash=5a1bc1296205e6fdbe3979728efe3920798885c1c4590b5f90f43222d239ca6a
CTRL-EVENT-EAP-TLS-CERT-ERROR reason=8 depth=0 subject='/C=US/ST=California/L=San Francisco/CN=Server/emailAddress=server@kir.nu' err='Server certificate chain probe'
CTRL-EVENT-EAP-FAILURE EAP authentication failed
Server certificate matching is configured with ca_cert, e.g.:
ca_cert="hash://server/sha256/5a1bc1296205e6fdbe3979728efe3920798885c1c4590b5f90f43222d239ca6a"
This functionality is currently available only with OpenSSL. Other
TLS libraries (including internal implementation) may be added in
the future.
The previous version could end leaking memory since os_free() was used
instead of wpabuf_free(). In addition, this could potentially have
triggered a crash if the TLS context were being freed when pending
input data where still in the buffer (though, this may not be possible
to trigger in practice).
The bsd_send_eapol() adds Ethernet header by itself. This patch changes it
to use l2_packet functionality.
I have tested on NetBSD 5.0.1 with WPA-PSK(TKIP).
On NetBSD, we should configure some parameters manually out of hostapd
like below.
ifconfig ath0 mediaopt hostap
ifconfig ath0 mode 11g
ifconfig ath0 chan 6
This patch does these automatically. Maybe there will be some
objections, like "hardware configuration is not hostapd/wpa_supplican's
work". So I will write the reasons why I made this patch.
1. For usability.
2. The first command fails when previous state is adhoc. This patch is
free from previous state.
3. Some driver wrappers configure these automatically (like nl80211).
4. I have wasted time trying to find out these command were needed :(
The ps3 wireless kernel driver has wireless extension support.
There is a legacy wpa_supplicant driver, and support for this
has been removed from the kernel driver, as no distributions
are using it.
This may help in debugging why cfg80211 refused the association
command since the scan results should include information about all
pending authentication and association states.
cfg80211 has a limit on pending authentications, so we better clear
the entries that we do not care about to avoid hitting the limit
when roaming between multiple APs.
This patch moves the authentication server setup before
IEEE 802.1X initialization. It's because 802.1X already
needs to have a valid SSL context.
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
This allows the driver wrappers to return two sets of IEs, so that
the BSS code can use information from both Beacon and Probe Response
frames if needed. For example, some Cisco APs seem to include more
information in Wireless Provisioning Services IE when it is in the
Beacon frame.
This makes the bridge parameter unnecessary for cases where the interface
is already in a bridge and sysfs is mounted to /sys so that the detection
code works.
For nl80211, the bridge parameter can be used to request the AP
interface to be added to the bridge automatically (brctl may refuse to
do this before hostapd has been started to change the interface mode).
If needed, the bridge interface is also created.
If the driver is detected to use cfg80211, we can rely on it being able
to disconnect with SIOCSIWMLME commands and to use empty SSID as a way
to stop it from associating when we are in progress of configuring the
driver for association. Consequently, we can remove the hack that uses
random 32-octet SSID to force disconnection and re-order association
commands to match the expectations that cfg80211 has for WEXT ioctls.
This gets rid of extra scan rounds and attempts to associate with the
silly 32-octet SSID.
Better make sure the eloop_timeout data gets fully initialized. The
current code is filling in all the fields, but it is clearer to just
zero the buffer to make sure any new field added to the structure gets
initialized.
This avoids potential use of uninitialized stack memory when printing
out peer address based on SMK error message that does not include the
MAC address.
wpa_sm_step() could theoretically free the statemachine, but it does
not do it in this particular case. Anyway, the code can be cleaned to
verify whether the state machine data is still available after the
wpa_sm_step() call.
On FreeBSD 8.0, driver_bsd.c build fails because of changes from
older versions of FreeBSD. The error messages are below:
In file included from ../src/drivers/driver_bsd.c:38:
/usr/include/net80211/ieee80211_crypto.h:94: error: 'IEEE80211_TID_SIZE'
undeclared here (not in a function)
../src/drivers/driver_bsd.c: In function 'wpa_driver_bsd_set_wpa_ie':
../src/drivers/driver_bsd.c:968: error: 'IEEE80211_IOC_OPTIE' undeclared (first
use in this function)
../src/drivers/driver_bsd.c:968: error: (Each undeclared identifier is reported
only once
../src/drivers/driver_bsd.c:968: error: for each function it appears in.)
gmake: *** [../src/drivers/driver_bsd.o] Error 1
This patch solves this issue.
wmm_ac_??_cw{min,max} parameters are in log form
When the wme_ac_??_cw{min,max} parameters aren't specified in
hostapd.conf, hostapd uses an incorrect set of default values, as the
defaults are in 2^x-1 form instead of in log form. This patch changes
them over to the expected log form.
Number of Linux driver wrappers included this more or less identical
function, so lets add a new helper file to be able to share some more
code between the driver wrappers.
The three existing enums were already depending on using the same
values in couple of places and it is just simpler to standardize on
one of these to avoid need for mapping between different enums for
the exact same thing.
Most of this file was already moved into wpa_supplicant/scan.c and
we can remove the file completely by having couple of small helper
functions copied to the remaining users outside core wpa_supplicant
code.
This fits better in wpa_supplicant/scan.c. Couple of remaining
scan_helpers.c functions are currently used in driver wrappers,
but they can likely be removed in the future.
This adds new commands and events for allowing off-channel Action
frame exchanges to be requested. This functionality is not yet used
and is only fully supported by driver_test.c at this point.
driver_nl80211.c has support for the remain-on-channel commands, but
the Action frame TX/RX part is still pending review for the kernel
code and as such, is not yet included here.
This adds placeholder code for allowing the virtual interfaces to be
pre-allocated a MAC address before the interface type is known with
drivers that do not handle interface type changes.
Get rid of wpa_supplicant_sta_rx() and add a new driver event that is
marked to be used only with driver_test.c. In addition, remove this
functionality from privsep wrapper. This is only use for client mode
MLME testing with driver_test.c.
Get more information about scans when updating BSS table information.
This allows the missing-from-scans expiration rule to work properly
when only partial set of channels or SSIDs are being scanned.
WPS IE parsing for PBC mode did not check whether the UUID-E attribute
was included before dereferencing the pointer. This could result in the
AP crashing when processing and invalid Probe Request frame.
There does not seem to be a driver interface for fetching auth_algs
capability, but this may be used by some external application, so
hardcode all auth_algs as supported for now.
This allows the driver interface to be deinitialized before
struct hostapd_data instance gets freed. This needs to be done so
that the driver wrapper does not maintain a context pointer to
freed memory.
Doxygen and some build tools may get a bit confused about same file
name being used in different directories. Clean this up a bit by
renaming some of the duplicated file names in src/ap.
Initialize struct hostapd_data driver context with the same driver
information that was initialized earlier during wpa_supplicant start.
This allows the AP mode operations to be completed directly with the
same calls in AP code without having to maintain a separate translation
layer between the AP and station mode driver context.
Skip WPS IE building for Beacon and Probe Response frames is set_ie_cb()
is not set. This fixes a memory leak and optimizes operations by not
allocating memory and building the WPS IEs unnecessarily.
This code can be shared by both hostapd and wpa_supplicant and this
is an initial step in getting the generic code moved to be under the
src directories. Couple of generic files still remain under the
hostapd directory due to direct dependencies to files there. Once the
dependencies have been removed, they will also be moved to the src/ap
directory to allow wpa_supplicant to be built without requiring anything
from the hostapd directory.
set_ap_wps_ie() is not used to set WPS IE for both Beacon and Probe
Response frames with a single call. In addition, struct wpabuf is used
instead of separate u8* and length fields. This avoids duplicated
allocation of the IEs and simplifies code in general.
This mode allows associated stations to use 4-address frames to allow
layer 2 bridging to be used. At least for the time being, this is only
supported with driver=nl80211.
This WPA_TRACE=y additions allows components to register active references
to memory that has been provided to them as a pointer. If such an actively
referenced memory area is freed, tracer will report this as an error and
backtraces of both the invalid free and the location where this pointer
was marked referenced are shown.
This adds config_methods configuration option for wpa_supplicant
following the design used in hostapd. In addition, the string is
now parsed in common code from src/wps/wps_common.c and the list
of configurable methods include all the defined methods from
WPS 1.0h spec.
Since an Enrollee that does not advertise display as one of the
Config Methods is unlikely to be able to show the ASCII passphrase
to the user, prefer PSK format with such an Enrollee to reduce key
derivation time. This can help with some low-powered devices that
would take long time to derive the PSK from the passphrase.
The use_psk_key parameter can now be used to force the Registrar to
use PSK format instead of ASCII passphrase when building a Credential
for the Enrollee. For now, this is not enabled, but it could be enabled
either based on external (to WPS) configuration or automatically set
based on some WPS attribute values from the Enrollee.
Undocumented (at least for the time being) TLS parameters can now
be provided in wpa_supplicant configuration to enable some workarounds
for being able to connect insecurely to some networks. phase1 and
phase2 network parameters can use following options:
tls_allow_md5=1
- allow MD5 signature to be used (disabled by default with GnuTLS)
tls_disable_time_checks=1
- ignore certificate expiration time
For now, only the GnuTLS TLS wrapper implements support for these.
The new TLS wrapper use may end up returning alert data and we need to
make sure here that it does not end up getting interpreted as success
due to non-NULL response.
This converts tls_connection_handshake(),
tls_connection_server_handshake(), tls_connection_encrypt(), and
tls_connection_decrypt() to use struct wpa_buf to allow higher layer
code to be cleaned up with consistent struct wpabuf use.
Use an extra header to move the returned pointer to break os_free()
or free() of the returned value and verify that the correct magic
is present when freeing or resizing the wpabuf. Show backtrace on
invalid wpabuf use.
If Finished message from peer has been received before the server
Finished message, start Phase 2 with the same message to avoid extra
roundtrip when the peer does not have anything to send after the server
Finished message.
Instead of forcefully deinitializing ER immediately, give it some
time to complete unsubscription and call eloop_terminate() only once
ER code has completed its work.
WPA_TRACE=y builds will now verify that memory allocation in done
consistently using os_{zalloc,malloc,realloc,strdup,free} (i.e., no
mixing of os_* functions and unwrapper functions). In addition, some
common memory allocation issues (double-free, memory leaks, etc.) are
detected automatically.
WPA_TRACE=y can now be used to enable internal backtrace support that
will provide more details about implementation errors, e.g., when some
resources are not released correctly. In addition, this will print out
a backtrace automatically if SIGSEGV is received.
As an initial step in sharing netlink helper functions among driver
wrappers, create a new file for netlink code and move operstate send
function there.
This message from tls_connection_handshake() is not really an error in
most cases, so do not show it if there was indeed no Application Data
available (which is a normal scenario and not an indication of any
error).
Replace driver wrapper calls to hostapd_tx_status(),
hostapd_rx_from_unknown_sta(), hostapd_mgmt_rx(), and
hostapd_mgmt_tx_cb() with new generic driver events
EVENT_TX_STATUS, EVENT_RX_FROM_UNKNOWN, and EVENT_RX_MGMT.
This cleans up lot of the driver wrapper code to be less dependent
on whether it is being used within wpa_supplicant AP mode or hostapd.
This remove the need from driver_test.c to go through internal hostapd
structures to find the appropriate BSS when reporting events on secondary
BSSes.
This removes need for including hostapd/sta_flags.h into driver
wrappers and removes any remaining dependencies between driver flags
and internal hostapd flags.
The Prism54.org project seems have been dead for a while and it does not
look like this driver would ever be maintained again. Furthermore, it is
difficult to find a version that would work with the driver_prism54.c
wrapper and there is another driver for these card in the Linux kernel
tree.
The hostapd integration in driver_prism54.c is quite different from the
other driver wrappers and would require major effort to get it cleaned
up. Since there does not seem to be any real users for the cleaned up
version, there does not seem to be justification to spend this effort on
the wrapper. This old code is making it much more difficult to clean up
the driver interface and at this point, the best option seems to be to
remove the driver wrappers. Should someone really still need this, the
old code will continue to be available in hostapd 0.6.x.
Instead of using the latest selected registrar change, collect selected
registrar information separately from all registrars and use the union
of this information when building the WPS IE for Beacon and Probe
Response frames.
Note: SetSelectedRegistrar UPnP action does not include a unique
identifier, so the ER matching routine is based only on the IP address
of the ER. In theory, there could be multiple ERs using the same IP
address (but different port or URL), so there may be some corner cases
that would not always match the correct ER entry at the AP. Anyway, this
is not really expected to occur in normal use cases and even if it did
happen, the selected registrar information is not any worse than it was
before when only the last change from any registrar for being
advertized.
This is more logical location for checking the URL and potentially
handling a call to another URL handler. In addition, return 404 error,
not invalid UPnP action, if the URL does not match.
These callbacks can be handled internally within core WPS code, so there
is no need to go through wps_hostapd.c with a callback function that is
just calling back into the core WPS code.
This can be handled internally within core WPS code, so there is no
need to go through wps_hostapd.c with a callback function that is just
calling back into the core WPS code.
IEEE 802.11w uses distinct key indexes (4 and 5) so the same
get_seqnum() handler can be used to fetch packet number for both
TKIP/CCMP and BIP(using IGTK).
Since the new get_seqnum_igtk() handler was not actually implemented by
any driver wrapper, this may also fix BIP/IGTK sequence number reporting
with driver_nl80211.c.
The password in User-Password AVP is padded to a multiple of 16 bytes
on EAP-TTLS/PAP. But when the password length is zero, no padding is
added. It doesn't cause connectivity issue. In fact, I could connect
with hostapd RADIUS server with zero length password.
I think it's better for obfuscation to pad the 16 bytes data when the
password length is zero with this patch.
There was code for configuring this, but no driver wrapper actually
implements the actual setting. Remove this for now to reduce potential
confusion and to simply the driver interface.
In addition to the bitrate, the only other variable in this structure
is used internally in hostapd. Move this structure into hostapd.h and
make the driver API use simpler data structure (array of bitrates).
These are not really used and can be removed to clean up the driver
interface definition. The only remaining flag (HOSTAPD_RATE_BASIC) can
be removed once the basic rate set indication can be handled
differently.
if_add/if_remove can now be used as the generic driver ops for adding
and removing virtual interfaces of various types. In addition,
driver_nl80211.c is now including this code unconditionally, so that
the functions are not limited only for hostapd.
On NetBSD 5.0.1, driver_bsd.c build fails with message below.
../src/drivers/driver_bsd.c: In function 'wpa_driver_bsd_associate':
../src/drivers/driver_bsd.c:1170: warning: implicit declaration of function 'wpa_driver_bsd_set_auth_alg'
../src/drivers/driver_bsd.c: At top level:
../src/drivers/driver_bsd.c:1204: error: static declaration of 'wpa_driver_bsd_set_auth_alg' follows non-static declaration
../src/drivers/driver_bsd.c:1170: error: previous implicit declaration of 'wpa_driver_bsd_set_auth_alg' was here
gmake: *** [../src/drivers/driver_bsd.o] Error 1
This patch solves this issue.
The new test-asn1 and test-x509 tools are built using libraries
from src/{utils,crypto,tls}. Currently, cross dependencies between
crypto and tls are still preventing the test-x509 from being linked
properly.
This is a separate program and is used mainly with hostapd, so it is
better to move this into the hostapd subdirectory now that Milenage
code has already been moved into src/crypto. Milenage was the only
generic component in hlr_auc_gw.
eap_example is now using src/crypto/libcrypto.a and src/tls/libtls.a
instead of providing own rules for building the files for these
components. TLS library selection is temporarily disabled for
eap_example (it will be built using internal crypto/TLS), but the
configuration option for this will eventually be restored with a new
libcrypto.a configuration option.
Clean up the internal TLS implementation by removing conditional
build blocks for (mostly) EAP-FAST specific functionality. This
will increase the size a big for non-EAP-FAST builds, but is quite
helpful in making src/tls/libtls.a with single build options. If
the potential size reduction is considered significant in the future,
this can be reconsider with a more library compatible way (e.g.,
external file with registration function, etc.).
This allows libeap.a and libeap.so to be built by merging in multiple
libraries from src subdirectories. In addition, this avoids wasting
extra space and time for local builds.
This fixes issues with some GnuTLS versions that seem to be adding
quite a bit of extra data into TLS messages. The EAP server code is
now using the same 300 byte extra room that was already used in the
EAP peer implementation.
The following defines are not really needed in most places, so
remove them to clean up source code and build scripts:
EAP_TLS_FUNCS
EAP_TLS_OPENSSL
EAP_TLS_GNUTLS
CONFIG_TLS_INTERNAL
There seem to be some cases in which wpa_supplicant and
cfg80211/mac80211 seem to have different understanding on
authentication/association state. Since cfg80211/mac80211 is very strict
on when it accepts new authentication/association/scan commands, try our
best at clearing such state mismatches by explicitly deauthenticating
from BSSes with which the driver claims we are associated with if we do
not have local information about such association.
Print what the kernel believes the current BSS status (authenticated
or associated) is in scan results. In addition, check whether this
matches with the state that wpa_supplicant believes the driver to be
in.
This does not change the actual behavior, but will provide information
that will help in debugging potential issues where cfg80211/mac80211
seems to get into a different state from wpa_supplicant. In addition,
this provides an easy location for a workaround that could be added to
clear cfg80211/mac80211 state for unknown BSSes.
This is an initial step in further cleaning up the EAPOL authenticator
use to avoid requiring direct accesses to the internal data structures.
For now, number of external files are still including the internal
definitions from eapol_auth_sm_i.h, but eventually, these direct
references should be removed.
In addition, start ordering header file includes to be in more
consistent order: system header files, src/utils, src/*, same
directory as the *.c file.
This removes the hardcoded definition from Makefile and cleans up
source code by moving the mail HOSTAPD_DUMP_STATE blocks into separate
files to avoid conditional compilation within files.
While this may not include knowledge of all EAP methods since this
depends on build configuration, it is better to not have to include
ieee802_1x.h into eapol_sm.c.
This makes it clearer which files are including header from src/common.
Some of these cases should probably be cleaned up in the future not to
do that.
In addition, src/common/nl80211_copy.h and wireless_copy.h were moved
into src/drivers since they are only used by driver wrappers and do not
need to live in src/common.
This avoids passing the raw scan results into the RSN code and by
doing so, removes the only dependency on src/drivers from the
src/rsn_supp code (or from any src subdirectory for that matter).
Instead of using hardcoded maximum A-MPDU length of 64 kB and no
restrictions on minimum MPDU Start Spacing, use the correct values
reported by the driver.
This is not actually used at all and it looks like the rules for
maintaining the old/new RADIUS configuration are not very clear in the
case the RADIUS client configuration did not change. Consequently, it
is better to just remove this for now and if similar functionality is
ever needed, redesign it to be easier to use without causing hard to
find issues with using freed memory.
Simpler approach to reconfiguring the RADIUS client would involve
just deinitializing the old context unconditionally and initializing
a new one whenever the configuration could have changed.
Use shared functions for converting Primary Device Type between binary
and string formats. In addition, use array of eight octets instead of a
specific structure with multiple fields to reduce code complexity.
Mainly, this is including header files to get definitions for functions
which is good to verify that the parameters match. None of these are
issues that would have shown as incorrect behavior of the program.
This gets rid of previously deprecated driver_ops handlers set_wpa,
set_drop_unencrypted, set_auth_alg, set_mode. The same functionality
can be achieved by using the init/deinit/associate handlers.
These driver wrappers should not be used anymore; WEXT should be used
instead. However, there may still be users stuck on older kernel versions
that may require driver specific wrappers, so the source code still
remains in the repository.
This moves the MTU definition into driver_hostap.c since it was really
meant to be specific to this driver. Since this was the last remaining
definition in hostapd_defs.h, remove that header file as unnecessary.
This code was copied from driver_hostap.c where it is used with the
special wlan#ap interface. It was not supposed to be used to change
the MTU for a normal data interface.
Clean up driver_nl80211.c by gettign rid of the last remaining WEXT use.
This requires that a recent mac80211 version is used to get full protection
in station mode via the authorized flag (IEEE 802.1X PAE).
Clean up driver interface by merging hostapd and wpa_supplicant
specific set_beacon driver_ops into a single one. In addition,
merge set_beacon_int into to the same operation.
If initialization fails, we could potentially try to sendto() on -1
socket which would fail. No point in doing that, so just return early
from the function.
The current MinGW/w32api versions seem to provide all the needed CryptoAPI
functions, so the code for loading these dynamically from the DLL can be
removed.
Need to define the workspace buffer properly to allow compiler to handle
strict aliasing between the incoming unsigned char[64] buffer as an u32
array. The previous version built with strict aliasing enabled can
result in SHA-1 producing incorrect results and consequently, with
4-way handshake failing.
This is based on a report and patch from Dan Williams <dcbw@redhat.com>
but with a different type (the union) used as a fix to avoid needing
extra type casting.
Discovered as part of the investigation of:
https://bugzilla.redhat.com/show_bug.cgi?id=494262#c32
if sha1 is built with gcc without turning off strict aliasing, it will
fail to correctly generate the hashes and will fail its own testcases as
well.
Signed-off-by: Dan Williams <dcbw@redhat.com>
This avoids some issues in cases where the ER has been started and
stopped multiple times on the same address and an AP may have stored
multiple event notification addresses for the same ER. The random
identifier allows the ER to filter out unexpected messages from further
processing.
Do not give the allocated memory to the subscription code since it was
not using it as-is anyway. This makes it easier to understand who owns
the allocation an is responsible of freeing it. This may potentially
fix some memory leaks on error paths.
The WPS 1.0h specification is quite unclear on what exactly should be
used as the MAC Address value in the Credential and AP Settings. It
looks like this should after all be the MAC Address of the Enrollee,
so change Registrar implementation to use that address instead of the
AP BSSID.
In addition, add validation code to the Enrollee implementation to
check the MAC Address value inside Credential (and also inside AP Settings)
to make sure it matches with the Enrollee's own address. However, since
there are deployed implementations that do not follow this interpretation
of the spec, only show the mismatch in debug information to avoid breaking
interoperability with existing devices.
This will need some additional code in wps_er_pbc() to handle PBC mode
enabling for a single AP only. For now, this can only be expected to work
when the ER is connected to a single AP.
UPnP device architecture specification requires all evented variables to
be included in the initial event message after subscription. Since this
can happen before we have seen any events, generated a dummy event
(WSC_ACK with all-zeros nonces) if needed.
This will notify control points of the services going away and allows
them to notice this without having to wait timeout on the
initial advertisements.
This removes following WFA WLANConfig Service actions and the related
state variables: GetAPSettings, SetAPSettings, DelAPSettings,
GetSTASettings, SetSTASettings, DelSTASettings, RebootAP,
ResetAP, RebootSTA, ResetSTA.
While WFA WLANConfig Service version 1.0 claims that some of these are
mandatory to implement for an AP, there are no known implementations
supporting these actions neither in an AP/proxy or an External Registrar
that would use them. These are unlikely to be supported in the future
either and as such, it is just simpler to get rid of them to clean up
the implementation and reduce code size.
When using UPnP transport, the Op-Code is not included, but the WPS
frame processing will need this. Generate a matching Op-Code based
on the message type.
Previously, WSC_MSG was hardcoded for every message from ER, but
this needs to be changed based on message type to send a valid
message to the Enrollee via EAP transport.
New PINs can now be added to WPS ER. This results in the ER code
using SetSelectedRegistrar to modify AP state so that Enrollees
will be able to notice the actice registrar more easily.
This keeps STA/Enrollee entries up to date and sets up registration
protocol session. M1 is processed and M2D generated, but the there
is no code yet to transmit the response back to the AP with
PutWLANResponse.
Always bring down the wlan interface, even when not changing the
BSSID, the interface also needs to be down for changing its type
from managed to AP mode.
The receive Probe Request and EAP-WSC notifications are now parsed
(including the TLVs in them) and contents is shown in the debug log.
Actual processing of the received information is still missing (TODO
comments indicate the needed functionality).
rand would be the address of rand() function and never NULL. The previous
version could have crashed on invalid AKA-AUTS command. Though, these
commands are only from hostapd which sends valid requests and as such,
the actual issue did not show up.
This is like wpa_msg(), but the output is directed only to
ctrl_interface listeners. In other words, the output will not be
shown on stdout or in syslog.
Change scan result reporting to use wpa_msg_ctrl() for
CTRL-EVENT-SCAN-RESULTS message at info level and wpa_printf() at
debug level to avoid showing scan result events in syslog in the
common configuration used with NetworkManager.
This adds code to start a HTTP server and to subscribe to UPnP events
from each discovered WPS AP. The event messages are received, but there
is not yet any code to actually parse the contents of the event.
Clean up code so that UPnP implementation does not need to include all
the HTTP functionality. In addition, make it easier to share HTTP server
functionality with other components in the future.
Instead of implementing HTTP client functionality inside
wps_upnp_event.c, use a generic HTTP client module to do this. The HTTP
client code can now be shared more easily for other purposes, too.
This is the first step in adding support for using wpa_supplicant as a
WPS External Registrar to manage APs over UPnP. Only the device
discovery part is implemented in this commit.
While the actual use here would be unlikely to be broken by any C
optimization, it is better to use explicit union construction to let
gcc know about the aliasing and avoid warnings from gcc 4.4.
gcc 4.4 ends up generating strict-aliasing warnings about some very common
networking socket uses that do not really result in a real problem and
cannot be easily avoided with union-based type-punning due to struct
definitions including another struct in system header files. To avoid having
to fully disable strict-aliasing warnings, provide a mechanism to hide the
typecast from aliasing for now. A cleaner solution will hopefully be found
in the future to handle these cases.
Though we have such a timeout when handling SetSelectedRegistrar UPnP
message from an external registrar, it looks like we don't have one when
the internal registrar is activated for PIN connection. Thus we set the
SelectedRegistrar flag when AP is activated for PIN connection but we
never reset it - not by some timeout, nor when registration succeeds.
This lead to situations where AP everlastingly declare that it is
activated for WPS PIN connection when in reality it is not.
Use the same timeout (and also success with PIN) to clear the selected
registrar flag when using internal registrar, too.
If PBC session overlap is detected during an ongoing PBC protocol run,
reject the run (if M8, i.e., credentials, have not yet been sent). This
provides a bit longer monitoring time at the Registrar for PBC mode to
catch some cases where two Enrollees in PBC mode try to enroll
credentials at about the same time.
This provides information about PBC mode result from the WPS Registrar
module. This could be used, e.g., to provide a user notification on the
AP UI on PBC failures.
