HT capability check is not required when starting AP on 6 GHz band as
only HE operation mode is allowed in the 6 GHz band.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
This extends hostapd and wpa_supplicant DPP implementation to allow the
bootstrapping URI to be generated for and parsed from an NFC Tag with an
NFC URI Record. This is similar to the way the bootstrapping URI is used
with QR Code for unidirectional authentication.
The DPP_BOOTSTRAP_GEN command uses "type=nfc-uri" to request the URI to
be assigned for NFC URI Record. In practice, the URI is generated
identically to the QR Code case, but the internal entry maintains the
NFC-URI type.
A new command "DPP_NFC_URI <uri>" can now be used to parse the URI read
from an NFC Tag with the NFC URI Record. This is similar to the
DPP_QR_CODE command.
Other commands (mainly, DPP_LISTEN and DPP_AUTH_INIT) are used for NFC
URI in the same way as they are used for QR Code.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Commit 844dfeb804 ("QCA vendor command support to set band to driver")
added a vendor command to pass 'SET setband' command information to the
driver in wpa_supplicant. Add similar changes to hostapd control
interface.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Previously, wpa_msg_register_cb() was called only from successful
completion of per-interface control interface initialization. This would
leave the callback unregistered in case only the global control
interface is used which would result in not delivering control interface
events on the global interface. Fix this by registering the callback
handler also from successful initialization of the global control
interface.
Signed-off-by: Veerendranath Jakkam <vjakkam@codeaurora.org>
Previously, hostapd sent only WPA_MSG_ONLY_GLOBAL type notifications to
the global control interface and all other notifications to
per-interface control interface. Extend this by making it similar to
wpa_supplicant global control interface notifications handling. With
this hostapd now sends all notifications except WPA_MSG_NO_GLOBAL to the
global control interface. In addition, WPA_MSG_PER_INTERFACE type
messages will be prefixed with "IFNAME=<interface name> " while sending
to the global control interface to indicate that the message is
interface specific.
Signed-off-by: Veerendranath Jakkam <vjakkam@codeaurora.org>
Previously, nonzero sae_h2e parameter values were used to perform SAE
H2E specific operations (deriving PT, adding RSNXE, adding H2E-only BSS
membership selector) in AP mode even if SAE was not enabled for the
network. This could result in unexpected behavior if sae_pwe=1 or
sae_pwe=2 were set in the configuration. Fix this by making the SAE
operations conditional on SAE being actually enabled.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
sigma_dut does not clear sae_pwe value when the command line argument
"-2" is used, so we need to explicitly clear this from wpa_supplicant at
the end of the test case.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
This allows Configurator to be configured to use the ssid64 option in
the discovery object for a station Enrollee.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
The discovery object is now allowed to use either the UTF-8 encoded
string ssid or base64url encoded ssid64.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Allow any pointer to be used as source for encoding and use char * as
the return value from encoding and input value for decoding to reduce
number of type casts needed in the callers.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Allow any pointer to be used as source for encoding and use char * as
the return value from encoding and input value for decoding to reduce
number of type casts needed in the callers.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
There is no use case for adding padding into the base64url encoded
strings, so remove the unneeded add_pad argument that was hardcoded to 0
in all callers.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
The UTF-8 encoded ssid string was replaced with base64url encoded ssid64
string, so update the implementation to match.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
The WMM TSPEC processor used the input buffer for processing the request
and building the response. This was fine for the FT case, but for the
WMM Action frame case, the input buffer is marked const, so it should
not really be modified. This modification could not really cause any
noticeable harm, but it can result in error reports from fuzzing and
potentially even from some static analyzers.
Fix this by marking the input arguments const more consistently (the
parsed IE was able to drop the const) and copy the const input data to a
temporary buffer for processing and modification instead of allowing the
input data to be modified.
Credit to OSS-Fuzz: https://bugs.chromium.org/p/oss-fuzz/issues/detail?id=19050
Signed-off-by: Jouni Malinen <j@w1.fi>
The previous description of wmediumd_scan_only_one used multiple lines
and that resulted in parallel-vm.py miscounting total number of test
cases. Fix that by getting rid of the newlines from the description.
Signed-off-by: Jouni Malinen <j@w1.fi>
Now that parallel-vm.py is actually stopping VMs as soon as they are not
needed for retries, it is not really an unexpected exit to see a VM exit
while test cases remain in the queue as long as at least that many VMs
remain running. Get rid of confusing 'unexpected exit' status from the
UI in such cases.
Fixes: 4aaddecdd8 ("tests: Handle test retries through the same queue")
Signed-off-by: Jouni Malinen <j@w1.fi>
Now that wpa_supplicant was modified to use NAI realm query even if
roaming_consortium is set, this test case is actually able to find a
match. Update it to avoid cause incorrect test failures.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Previously ANQP fetch considered NAI realm query only when cred block
did not specify roaming_consortium to optimize ANQP operations (NAI
realm list can have a very long value). In certain cases, both NAI realm
and roaming_consortium are configured in credential block and this
resulted in ANQP fetch for NAI realm not being initiated. That could
result in not being able to select the highest priority available
credential/network.
Remove roaming_consortium check for NAI realm query inclusion in ANQP
request so that we will request NAI realm information whenever it can
result in matching additional networks. This makes the ANQP queries more
costly in some cases, but the additional information is needed for
correct behavior in network selection.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Commit 947b5a1532 ("P2P: Stop listen state if Action frame TX is
needed on another channel") added an optimization for P2P response
transmission in certain concurrent operation cases. However, it did not
take into account possibility of the driver not being in listen
state (p2p->drv_in_listen == 0) and could end up getting stuck with the
P2P state machine in a manner that made the device not listen for
following messages. This showed up in following manner in the debug log:
P2P: Starting short listen state (state=SEARCH)
P2P: Driver ended Listen state (freq=2437)
process received frame and send a response
P2P: Stop listen on 0 MHz to allow a frame to be sent immediately on 2437 MHz
P2P: Clear timeout (state=SEARCH)
--> state machine stuck
Fix this by adding drv_in_listen > 0 condition for the optimization to
stop the listen operation in send_action() resulting in scheduled TX.
Fixes: 947b5a1532 ("P2P: Stop listen state if Action frame TX is needed on another channel")
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Update center frequency and center frequency2's DFS channel status in
VHT80+80 mode. Otherwise it will cause AP failed to start on a DFS
channel.
Tested: qca9984 with firmware ver 10.4-3.10-00047
Signed-off-by: Rick Wu <rwu@codeaurora.org>
Signed-off-by: Lei Wang <leiwa@codeaurora.org>
wpa_validate_wpa_ie() was already extended to cover these cases with
WPA_INVALID_PMKID return value, but hostapd_notif_assoc() did not have
code for mapping this into the appropriate status code
(STATUS_INVALID_PMKID) and ended up using the default
(WLAN_STATUS_INVALID_IE) instead. This caused AP SME-in-driver cases
returning incorrect status code when the AP did not have a matching
PMKSA cache entry. This could result in unexpected station behavior
where the station could continue trying to use a PMKSA cache entry that
the AP does not have and not being able to recover this.
Fix this by adding the previously missed mapping of validation errors to
status/reason codes.
Fixes: 567da5bbd0 ("DPP: Add new AKM")
Fixes: 458d8984de ("SAE: Reject request with mismatching PMKID (no PMKSA cache entry)")
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
wpas_dbus_handler_scan() constructs a set of 'params' each time, but it
doesn't acknowledge the existing randomization settings when doing so.
That means that any D-Bus initiated scans weren't going to follow the
configured settings.
Signed-off-by: Eric Caruso <ejcaruso@chromium.org>
Add D-Bus property:
* MACAddressRandomizationMask: a{say}
which configure random MAC address functionality in the Wi-Fi
driver via netlink.
Signed-off-by: Eric Caruso <ejcaruso@chromium.org>
This array can be freed either from the scan parameters or from
clearing the MAC address randomization parameters from the
wpa_supplicant struct. To make this ownership more clear, we have
each struct own its own copy of the parameters.
Signed-off-by: Eric Caruso <ejcaruso@chromium.org>
These parameter use hexdump values over the control interface, so
mention them in the DPP example documentation.
Signed-off-by: Jouni Malinen <j@w1.fi>
The "\\u%04x" printf string did not really work in the correct way if
char is signed. Fix this by type casting this to unsigned char.
Signed-off-by: Jouni Malinen <j@w1.fi>
There was a bug in wmediumd in that it didn't set the
frequency of frames, and thus they were always received
by mac80211_hwsim, regardless of channel it was on.
Add two tests that verify we only find a single instance
of an AP if we only have that one, and run this both with
and without wmediumd.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Avoid race conditions in completing mesh group removal/re-addition steps
and starting connectivity check. It seemed to be possible to get to the
connectivity test in some cases before the mesh STA had rejoined the
mesh and completed key configuration.
Signed-off-by: Jouni Malinen <j@w1.fi>
Export a new 'owe' capability to indicate that wpa_supplicant was
built with OWE support and accepts 'key_mgmt=OWE'. Also, support 'owe'
in the array of BSS' available key managements.
Signed-off-by: Beniamino Galvani <bgalvani@redhat.com>
When the P2P management interface is deleted, P2P is then disabled and
global->p2p_init_wpa_s is set to NULL. After that, other interfaces can
still trigger P2P functions (like wpas_p2p_find()) using D-Bus. This
makes wpa_supplicant terminate with SIGSEGV, because it dereferences a
NULL pointer. Fix this by adding proper checks, like it's done with
wpa_cli.
CC: Beniamino Galvani <bgalvani@redhat.com>
CC: Benjamin Berg <benjamin@sipsolutions.net>
Reported-by: Vladimir Benes <vbenes@redhat.com>
Signed-off-by: Davide Caratti <davide.caratti@gmail.com>
SUITE_B_192 AKM capability was indicated for all devices using the
nl80211 driver (without the QCA vendor specific AKM capability
indication). However, some devices can't handle Suite B 192 due to
insufficient ciphers supported. Add a check for CCMP-256 or GCMP-256
cipher support and only indicate SUITE_B_192 capability when such cipher
is supported. This allows compiling with CONFIG_SUITEB192 and still get
proper response to the 'GET_CAPABILITY key_mgmt' command. Under Android
it can also serve as a dynamic way for HAL to query platform for
WPA3-Enterprise 192-bit support.
Signed-off-by: Mikael Kanstrup <mikael.kanstrup@sony.com>
Previously, an unexpected SAE commit message resulted in forcing
disconnection. While that allowed recovery by starting from scratch,
this is not really necessary. Ignore such unexpected SAE commit message
instead and allow SAE confirm message to be processed after this. This
is somewhat more robust way of handling the cases where SAE commit
message might be retransmitted either in STA->AP or AP->STA direction.
Signed-off-by: Jouni Malinen <j@w1.fi>
wpa_key_mgmt_wpa_psk() includes SAE AKMs. However, with SAE, there is no
way of reaching 4-way handshake without the password having already been
verified as part of SAE authentication. As such, a failure to complete
4-way handshake with SAE cannot indicate that the used password was
incorrect.
Signed-off-by: Jouni Malinen <j@w1.fi>
