This can be used to drop any pending ERP key from both the internal AP
authentication server and RADIUS server use of hostapd.
Signed-off-by: Jouni Malinen <j@w1.fi>
The new hostapd.conf radio_measurements parameter can now be used to
configure a test build to advertise support for radio measurements with
neighbor report enabled. There is no real functionality that would
actually process the request, i.e., this only for the purpose of minimal
STA side testing for now.
Signed-off-by: Jouni Malinen <j@w1.fi>
Previously, only WPA + WPA2 was covered. If FT is enabled in addition to
WPA, MDIE is included in the buffer between RSN and WPA elements. The
previous version ended up leaving only the MDIE after having skipped RSN
element. Fix this to skip MDIE as well to leave only WPA IE regardless
of whether FT is enabled in AP configuration.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This converts os_snprintf() result validation cases to use
os_snprintf_error() in cases where success condition was used to execute
a step. These changes were done automatically with spatch using the
following semantic patch:
@@
expression E1,E2,E3;
statement S1;
@@
E1 = os_snprintf(E2, E3, ...);
- if (\( E1 >= 0 \| E1 > 0 \) && \( (size_t) E1 < E3 \| E1 < (int) E3 \| E1 < E3 \))
+ if (!os_snprintf_error(E3, E1))
S1
Signed-off-by: Jouni Malinen <j@w1.fi>
Previously, the immediate EAPOL authenticator startup was scheduled
without having received EAPOL-Start only for the case where WPA/WPA2 was
enabled. This can be extended to speed up non-WPA/WPA2 cases as well if
the STA includes WPS IE in Association Request frame.
Signed-off-by: Jouni Malinen <j@w1.fi>
If "ADD bss_config=" command failed in driver_init() or
hostapd_setup_interface(), some of the allocated resources were not
freed properly.
Signed-off-by: Jouni Malinen <j@w1.fi>
Using aes_wrap() to initialize a data structure seemed to be too much
for some static analyzers to understand. Make it obvious that the target
is not just the single struct member. (CID 68111)
Signed-off-by: Jouni Malinen <j@w1.fi>
Using aes_unwrap() to initialize a data structure seemed to be too much
for some static analyzers to understand. Make it obvious that the target
is initialized and that the target is not just the single struct member.
In addition, clean up the design to avoid removal of const with a
typecast. (CID 68112, CID 68134, CID 68135, CID 68136)
Signed-off-by: Jouni Malinen <j@w1.fi>
Commit 16689c7cfc ('hostapd: Allow ACS to
be offloaded to the driver') used incorrect operator to determine
whether HT40 was configured. Fix that to mask the ht_capab bit
correctly. (CID 77286)
Signed-off-by: Jouni Malinen <j@w1.fi>
Derive rRK and rIK on EAP server if ERP is enabled and use these keys to
allow EAP re-authentication to be used and to derive rMSK.
The new hostapd configuration parameter eap_server_erp=1 can now be used
to configure the integrated EAP server to derive EMSK, rRK, and rIK at
the successful completion of an EAP authentication method. This
functionality is not included in the default build and can be enabled
with CONFIG_ERP=y.
Signed-off-by: Jouni Malinen <j@w1.fi>
hostapd can now be configured to transmit EAP-Initiate/Re-auth-Start
before EAP-Request/Identity to try to initiate ERP. This is disabled by
default and can be enabled with erp_send_reauth_start=1 and optional
erp_reauth_start_domain=<domain>.
Signed-off-by: Jouni Malinen <j@w1.fi>
Using QCA vendor command, allow ACS function to be offloaded to the
driver. Once channels are selected, hostapd is notified to perform OBSS
operation.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This flag was left in the STA entry for the short duration after the STA
gets deauthenticated. If the STA sends a Class 2 or 3 frame during that
short time, the AP would not have replied with Deauthentication frame
indicating no association is present.
Signed-off-by: Jouni Malinen <j@w1.fi>
hostapd was still providing couple of parameters that were used only in
the already removed driver_test.c framework.
Signed-off-by: Jouni Malinen <j@w1.fi>
This field needs to be validated in addition to validating the total
length of the received frame to avoid reading beyond the frame buffer.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Only the NS frames should be checked to be long enough to cover all the
fields used in the NS data structure. This allows shorter RA and NA
frames to be processed for multicast-to-unicast rules.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
l2_packet_send() returns >= 0 on success, i.e., non-zero value does not
mean failure. Fix this debug print to show up only on negative return
values.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This makes it easier to debug operations. The debug message is marked
EXCESSIVE, though, to avoid filling the logs with too much information
in default debugging cases.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
There is no point in trying to send the unicast converted version to a
STA that is not in authorized state since the driver would be expected
to drop normal TX Data frames in such state.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
These need to be marked packed to avoid issues with compilers
potentially adding padding between the fields (e.g., gcc on 64-bit
seemed to make struct icmpv6_ndmsg two octets too long which broke IPv6
address discovery).
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This replaces the use of Linux kernel header files (linux/ip.h,
linux/udp.h, linux/ipv6.h, and linux/icmpv6.h) with equivalent header
files from C library. In addition, ndisc_snoop.c is now built
conditionally on CONFIG_IPV6=y so that it is easier to handle hostapd
builds with toolchains that do not support IPv6 even if Hotspot 2.0 is
enabled in the build.
Signed-off-by: Jouni Malinen <j@w1.fi>
This commit inserts Finite Cyclic Group to Anti-Clogging Token request
frame because IEEE Std 802.11-2012, Table 8-29 says "Finite Cyclic Group
is present if Status is zero or 76".
Signed-off-by: Masashi Honma <masashi.honma@gmail.com>
The mesh anti-clogging functionality is implemented partially. This
patch fixes to parse anti-clogging request frame and use anti-clogging
token.
Signed-off-by: Masashi Honma <masashi.honma@gmail.com>
This extends the earlier PeerKey station side design to be used on the
AP side as well by passing pointer and already validated length from the
caller rather than parsing the length again from the frame buffer. This
avoids false warnings from static analyzer (CID 62870, CID 62871,
CID 62872).
Signed-off-by: Jouni Malinen <j@w1.fi>
hostapd control interface can now be used to request transmission of a
BSS Transition Management Request frame to a specified station.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
If the 4-way handshake ends up having to retransmit the EAPOL-Key
message 1/4 due to a timeout on waiting for the response, it is possible
for the Supplicant to change SNonce between the first and second
EAPOL-Key message 2/4. This is not really desirable due to extra
complexities it causes on the Authenticator side, but some deployed
stations are doing this.
This message sequence looks like this:
AP->STA: EAPOL-Key 1/4 (replay counter 1, ANonce)
AP->STA: EAPOL-Key 1/4 (replay counter 2, ANonce)
STA->AP: EAPOL-Key 2/4 (replay counter 1, SNonce 1)
AP->STA: EAPOL-Key 3/4 (replay counter 3, ANonce)
STA->AP: EAPOL-Key 2/4 (replay counter 2, SNonce 2)
followed by either:
STA->AP: EAPOL-Key 4/4 (replay counter 3 using PTK from SNonce 1)
or:
AP->STA: EAPOL-Key 3/4 (replay counter 4, ANonce)
STA->AP: EAPOL-Key 4/4 (replay counter 4, using PTK from SNonce 2)
Previously, Authenticator implementation was able to handle the cases
where SNonce 1 and SNonce 2 were identifical (i.e., Supplicant did not
update SNonce which is the wpa_supplicant behavior) and where PTK
derived using SNonce 2 was used in EAPOL-Key 4/4. However, the case of
using PTK from SNonce 1 was rejected ("WPA: received EAPOL-Key 4/4
Pairwise with unexpected replay counter" since EAPOL-Key 3/4 TX and
following second EAPOL-Key 2/4 invalidated the Replay Counter that was
used previously with the first SNonce).
This commit extends the AP/Authenticator workaround to keep both SNonce
values in memory if two EAPOL-Key 2/4 messages are received with
different SNonce values. The following EAPOL-Key 4/4 message is then
accepted whether the MIC has been calculated with the latest SNonce (the
previously existing behavior) or with the earlier SNonce (the new
extension). This makes 4-way handshake more robust with stations that
update SNonce for each transmitted EAPOL-Key 2/4 message in cases where
EAPOL-Key message 1/4 needs to be retransmitted.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
When DGAF Disable is on, perform multicast-to-unicast for DHCP packets
and Router Advertisement packets. This is a requirement for Hotspot 2.0.
Signed-off-by: Kyeyoon Park <kyeyoonp@qca.qualcomm.com>
This commit establishes the infrastructure, and handles the Neighbor
Solicitation and Neighbor Advertisement frames. This will be extended
in the future to handle other frames.
Signed-off-by: Kyeyoon Park <kyeyoonp@qca.qualcomm.com>
Multicast-to-unicast conversion send will be needed in various part of
Proxy ARP and DGAF Disable.
Signed-off-by: Kyeyoon Park <kyeyoonp@qca.qualcomm.com>
This allows adding/deleting an IPv6 neighbor entry to/from the bridge,
to which the BSS belongs. This commit adds the needed functionality in
driver_nl80211.c for the Linux bridge implementation. In theory, this
could be shared with multiple Linux driver interfaces, but for now, only
the main nl80211 interface is supported.
Signed-off-by: Kyeyoon Park <kyeyoonp@qca.qualcomm.com>
It is possible that a station device might miss an ACK for an
authentication, association, or action frame, and thus retransmit the
same frame although the frame is already being processed in the stack.
While the duplicated frame should really be dropped in the kernel or
firmware code where duplicate detection is implemented for data frames,
it is possible that pre-association cases are not fully addressed (which
is the case at least with mac80211 today) and the frame may be delivered
to upper layer stack.
In such a case, the local AP will process the retransmitted frame although
it has already handled the request, which might cause the station to get
confused and as a result disconnect from the AP, blacklist it, etc.
To avoid such a case, save the sequence control of the last processed
management frame and in case of retransmissions drop them.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
If DFS implementation was built in, some configurations with drivers
that do not provide mode information could end up dereferencing a NULL
pointer. Fix this by skipping DFS operations in such cases since not
having information about modes and channels means that hostapd could not
perform DFS anyway (i.e., either this is not a wireless driver or the
driver takes care of DFS internally).
Signed-off-by: Jouni Malinen <j@w1.fi>
Commit 7f0303d5b0 ('hostapd: Verify VHT
160/80+80 MHz driver support') added couple of hapd->iface->current_mode
dereferences of which the one in hostapd_set_freq() can be hit with some
configuration files when using driver wrappers that do not have hw_mode
data, i.e., when current_mode is NULL. This could result in segmentation
fault when trying to use driver=wired. Fix this by checking that
current_mode is not NULL before dereferencing it to get vht_capab.
Signed-off-by: Jouni Malinen <j@w1.fi>
This patch makes four MIB variables for plink configurable and sets the
correct default values based on IEEE Std 802.11s-2011.
Signed-off-by: Masashi Honma <masashi.honma@gmail.com>
Add timer to do SAE re-authentication with number of tries defined
by MESH_AUTH_RETRY and timeout defined by MESH_AUTH_TIMEOUT.
Ignoring the sending of reply message on "SAE confirm before commit"
to avoid "ping-pong" issues with other mesh nodes. This is obvious when
number of mesh nodes in MBSS reaching 6.
Signed-off-by: Chun-Yeow Yeoh <yeohchunyeow@gmail.com>
Signed-off-by: Bob Copeland <me@bobcopeland.com>
Add state transition logic to the SAE frame handling in order to more
fully implement the state machine from the IEEE 802.11 standard. Special
cases are needed for infrastructure BSS case to avoid unexpected
Authentication frame sequence by postponing transmission of the second
Authentication frame untile the STA sends its Confirm.
[original patch by: Thomas Pedersen <thomas@noack.us>]
Signed-off-by: Bob Copeland <me@bobcopeland.com>
New kernels in wiphy_suspend() will call cfg80211_leave_all() that will
eventually end up in cfg80211_stop_ap() unless wowlan_triggers were set.
For now, use the parameters from the station mode as-is. It may be
desirable to extend (or constraint) this in the future for specific AP
mode needs.
Signed-off-by: Dmitry Shmidt <dimitrysh@google.com>
This adds support for AKM 00-0F-AC:11 to specify the integrity and
key-wrap algorithms for EAPOL-Key frames using the new design where
descriptor version is set to 0 and algorithms are determined based on
AKM.
Signed-off-by: Jouni Malinen <j@w1.fi>
The new AKM uses a different mechanism of deriving the PMKID based on
KCK instead of PMK. hostapd was already doing this after the KCK had
been derived, but wpa_supplicant functionality needs to be moved from
processing of EAPOL-Key frame 1/4 to 3/4 to have the KCK available.
Signed-off-by: Jouni Malinen <j@w1.fi>
This adds definitions for the 128-bit level Suite B AKM 00-0F-AC:11. The
functionality itself is not yet complete, i.e., this commit only
includes parts to negotiate the new AKM.
Signed-off-by: Jouni Malinen <j@w1.fi>
Some flag already using a bit larger than 32, so extend the hostapd
drv_flags type similarly to the earlier wpa_supplicant change to get the
full flag content.
Signed-off-by: Yanbo Li <yanbol@qti.qualcomm.com>
This was used in hostapd driver_test.c, but that driver wrapper has been
removed and there are no remaining or expected users for
EVENT_FT_RRB_RX.
Signed-off-by: Jouni Malinen <j@w1.fi>
Proxy ARP allows the AP devices to keep track of the hardware address to
IP address mapping of the STA devices within the BSS. When a request for
such information is made (i.e., ARP request, Neighbor Solicitation), the
AP will respond on behalf of the STA device within the BSS. Such
requests could originate from a device within the BSS or also from the
bridge. In the process of the AP replying to the request (i.e., ARP
reply, Neighbor Advertisement), the AP will drop the original request
frame. The relevant STA will not even know that such information was
ever requested.
This feature is a requirement for Hotspot 2.0, and is defined in IEEE
Std 802.11-2012, 10.23.13. While the Proxy ARP support code mainly
resides in the kernel bridge code, in order to optimize the performance
and simplify kernel implementation, the DHCP snooping code was added to
the hostapd.
Signed-off-by: Kyeyoon Park <kyeyoonp@qca.qualcomm.com>
This allows setting a network parameter on the bridge that the BSS
belongs to.
This commit adds the needed functionality in driver_nl80211.c for the
Linux bridge implementation. In theory, this could be shared with
multiple Linux driver interfaces, but for now, only the main nl80211
interface is supported.
Signed-off-by: Kyeyoon Park <kyeyoonp@qca.qualcomm.com>
This allows setting a bridge port attribute. Specifically, the bridge
port in this context is the port to which the BSS belongs.
This commit adds the needed functionality in driver_nl80211.c for the
Linux bridge implementation. In theory, this could be shared with
multiple Linux driver interfaces, but for now, only the main nl80211
interface is supported.
Signed-off-by: Kyeyoon Park <kyeyoonp@qca.qualcomm.com>
This allows adding/deleting an IPv4 neighbor entry to/from the bridge,
to which the BSS belongs. This commit adds the needed functionality in
driver_nl80211.c for the Linux bridge implementation. In theory, this
could be shared with multiple Linux driver interfaces, but for now, only
the main nl80211 interface is supported.
Signed-off-by: Kyeyoon Park <kyeyoonp@qca.qualcomm.com>
These can be convenient for upper layer programs to determine if the
hostapd interface gets disabled/re-enabled, e.g., due to rfkill
block/unblock.
Signed-off-by: Jouni Malinen <j@w1.fi>
Use the 'no_ir' notation instead of the 'passive scan' and
'no_ibss' notations to match the earlier change in nl80211.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Modify hostapd.c logic to add checks for valid mconf data structure:
- For hostapd_setup_bss we don't need to flush old stations in case
we're rejoining a mesh network.
- In hostapd_setup_interface_complete, we don't need to setup the
interface until we join the mesh (same reasoning for
hostapd_tx_queue_params).
Signed-off-by: Javier Lopez <jlopex@gmail.com>
Signed-off-by: Jason Mobarak <x@jason.mobarak.name>
The mesh peering manager establishes and maintains links among
mesh peers, tracking each peer link via a finite state machine.
This implementation supports open mesh peerings.
[assorted fixes from Yu Niiro <yu.niiro@gmail.com>]
[more fixes from Masashi Honma <masashi.honma@gmail.com>]
Signed-off-by: Javier Lopez <jlopex@gmail.com>
Signed-off-by: Javier Cardona <javier@cozybit.com>
Signed-off-by: Ashok Nagarajan <ashok.dragon@gmail.com>
Signed-off-by: Jason Mobarak <x@jason.mobarak.name>
Signed-hostap: Bob Copeland <me@bobcopeland.com>
Add routines to (de)initialize mesh interface data structures and
join and leave mesh networks.
Signed-off-by: Javier Lopez <jlopex@gmail.com>
Signed-off-by: Javier Cardona <javier@cozybit.com>
Signed-off-by: Jason Mobarak <x@jason.mobarak.name>
Signed-off-by: Thomas Pedersen <thomas@noack.us>
If both HT and VHT was enabled on AP and channel switch event from the
driver indicated that HT was disabled, VHT was left enabled. This
resulted in the following channel configuration failing. Fix this by
disabling VHT if HT gets disabled.
Signed-off-by: Jouni Malinen <j@w1.fi>
Add smps_modes field, and let the driver fill it with its supported SMPS
modes (static/dynamic). This will let us start an AP with specific SMPS
mode (e.g., dynamic) that will allow it to reduce its power usage.
Signed-off-by: Eliad Peller <eliad@wizery.com>
This avoids an issue where a wpa_supplicant build with CONFIG_P2P=y and
CONFIG_HS20=y ended up processing a P2P SD query twice when operating as
a GO and sending out two replies. Only the P2P SD implementation should
reply to P2P SD query in such a case.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
The new "bss_load_update_period" parameter can be used to configure
hostapd to advertise its BSS Load element in Beacon and Probe Response
frames. This parameter is in the units of BUs (Beacon Units).
When enabled, the STA Count and the Channel Utilization value will be
updated periodically in the BSS Load element. The AAC is set to 0 sinze
explicit admission control is not supported. Channel Utilization is
calculated based on the channel survey information from the driver and
as such, requires a driver that supports providing that information for
the current operating channel.
Signed-off-by: Kyeyoon Park <kyeyoonp@qca.qualcomm.com>
It is now possible to run hwsim_test like data connectivity test through
wpa_supplicant/hostapd control interface if CONFIG_TESTING_OPTIONS=y is
used for the build. Test functionality is enabled/disabled at runtime
with "DATA_TEST_CONFIG <1/0>". The "DATA_TEST_TX <dst> <src> <tos>"
command can be used to request a test frame to be transmitted.
"DATA-TEST-RX <dst> <src>" event is generated when the test frame is
received.
Signed-off-by: Jouni Malinen <j@w1.fi>
This makes hostapd create PMKSA cache entries from SAE authentication
and allow PMKSA caching to be used with the SAE AKM.
Signed-off-by: Jouni Malinen <j@w1.fi>
This allows multiple sessions using the same PMKSA cache entry to be
combined more easily at the server side. Acct-Session-Id is still a
unique identifier for each association, while Acct-Multi-Session-Id will
maintain its value for all associations that use the same PMKSA.
Signed-off-by: Jouni Malinen <j@w1.fi>
Commit 8b24861154 ('Add Acct-Session-Id
into Access-Request messages') added Acct-Session-Id building into the
helper function shared between authentication and accounting messages.
However, it forgot to remove the same code from the generation of
accounting messages and as such, ended up with Accounting-Request
messages containing two copies of this attribute. Fix this by removing
the addition of this attribute from the accounting specific function.
Signed-off-by: Jouni Malinen <j@w1.fi>
The new openssl_cipher configuration parameter can be used to select
which TLS cipher suites are enabled when hostapd is used as an EAP
server with OpenSSL as the TLS library.
Signed-off-by: Jouni Malinen <j@w1.fi>
This use does not really need a strong random number, so fall back to
os_random() if a theoretical error case occurs. (CID 72682)
Signed-off-by: Jouni Malinen <j@w1.fi>
While this specific case does not really care what value is used, the
the theoretical error case can be handled more consistently. (CID 72684)
Signed-off-by: Jouni Malinen <j@w1.fi>
The hlen and len variables are identical here, but only the hlen was
used in the end. Change this to use the len variable to avoid
unnecessary static analyzer warnings about unused writes.
Signed-off-by: Jouni Malinen <j@w1.fi>
It looks like the use of sm->wpa == WPA_VERSION_WPA2 in two locations
within the function was a bit too much for clang static analyzer to
understand. Use a separate variable for storing the allocated memory so
that it can be freed unconditionally. The kde variable can point to
either stack memory or temporary allocation, but that is now const
pointer to make the design clearer.
Signed-off-by: Jouni Malinen <j@w1.fi>
The new ext_eapol_frame_io parameter can be used to configure hostapd
and wpa_supplicant to use control interface for receiving and
transmitting EAPOL frames. This makes it easier to implement automated
test cases for protocol testing. This functionality is included only in
CONFIG_TESTING_OPTIONS=y builds.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
A P2P Client may be able to connect to the GO even if the WPS
provisioning step has not terminated cleanly (e.g., P2P Client does not
send WSC_Done). Such group formation attempt missed the event
notification about started group on the GO and also did not set the
internal state corresponding to the successful group formation.
This commit addresses the missing part by completing GO side group
formation on a successful first data connection if WPS does not complete
cleanly. Also, this commit reorders the STA authorization indications to
ensure that the group formation success notification is given prior to
the first STA connection to handle such scenarios.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This allows cases where neither 80 MHz segment requires DFS to be
configured. DFS CAC operation itself does not yet support 80+80, though,
so if either segment requires DFS, the AP cannot be brought up.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This adds kek_len argument to aes_wrap() and aes_unwrap() functions and
allows AES to be initialized with 192 and 256 bit KEK in addition to
the previously supported 128 bit KEK.
The test vectors in test-aes.c are extended to cover all the test
vectors from RFC 3394.
Signed-off-by: Jouni Malinen <j@w1.fi>
_pmksa_cache_free_entry() is a static function that is never called with
entry == NULL, so there is no need to check for that.
Signed-off-by: Jouni Malinen <j@w1.fi>
If the first entry in the PMKSA cache did not match the station's MAC
address, an infinite loop could be reached in pmksa_cache_get_okc() when
trying to find a PMKSA cache entry for opportunistic key caching cases.
This would only happen if OKC is enabled (okc=1 included in the
configuration file).
Signed-off-by: Jouni Malinen <j@w1.fi>
Previously, WPA/WPA2 case ended up using the hardcoded
dot11RSNAConfigPMKLifetime (43200 seconds) for PMKSA cache entries
instead of using the Session-Timeout value from the RADIUS server (if
included in Access-Accept). Store a copy of the Session-Timeout value
and use it instead of the default value so that WPA/WPA2 cases get the
proper timeout similarly to non-WPA/WPA2 cases.
Signed-off-by: Jouni Malinen <j@w1.fi>
In case P2P is not enabled the if (dev_addr) is always ignored as
dev_addr will be NULL. As this code is relevant only to P2P, it can be
moved to be the ifdef to avoid static analyzer warnings. (CID 72907)
Signed-off-by: Philippe De Swert <philippe.deswert@jollamobile.com>
This fixes couple of code paths where the WPA_DRIVER_FLAGS_DFS_OFFLOAD
flag was not checked properly and unexpected DFS operations were
initiated (and failed) in case the driver handles all these steps.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
The driver-based SME case did not set STA flags properly to the kernel
in the way that hostapd-SME did in ieee802_11.c. This resulted in the FT
protocol case not marking the STA entry authorized. Fix that by handling
the special WLAN_AUTH_FT case in hostapd_notif_assoc() and also add the
forgotten hostapd_set_sta_flags() call to synchronize these flag to the
driver.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
While hostapd should not really receive the EVENT_ASSOC message for
IBSS, driver_nl80211.c could potentially generate that if something
external forces the interface into IBSS mode and the IBSS case does not
provide the struct assoc_info data. Avoid the potential NULL pointer
dereference by explicitly verifying for the event data to be present.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This adds hostapd support for the new WLAN-Pairwise-Cipher,
WLAN-Group-Cipher, WLAN-AKM-Suite, and WLAN-Group-Mgmt-Pairwise-Cipher
attributes defined in RFC 7268. These attributes are added to RADIUS
messages when the station negotiates use of WPA/RSN.
Signed-off-by: Jouni Malinen <j@w1.fi>
This adds hostapd support for the new WLAN-HESSID attribute defined in
RFC 7268. This attribute contains the HESSID and it is added whenever
Interworking is enabled and HESSID is configured.
Signed-off-by: Jouni Malinen <j@w1.fi>
This adds hostapd support for the new Mobility-Domain-Id attribute
defined in RFC 7268. This attribute contains the mobility domain id and
it is added whenever the station negotiates use of FT.
Signed-off-by: Jouni Malinen <j@w1.fi>
set_dfs_state() return value is not currently checked anywhere, so
remove the dead assignment to avoid static analyzer complaints.
Signed-off-by: Jouni Malinen <j@w1.fi>
