The nl80211 driver can report low ACK condition (in fact it reports
complete loss right now only). Use that, along with a config option, to
disconnect stations when the data connection is not working properly,
e.g., due to the STA having went outside the range of the AP. This is
disabled by default and can be enabled with disassoc_low_ack=1 in
hostapd or wpa_supplicant configuration file.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
If a station received unprotected Deauthentication or Disassociation
frame with reason code 6 or 7 from the current AP, there may be a
mismatch in association state between the AP and STA. Verify whether
this is the case by using SA Query procedure. If not response is
received from the AP, deauthenticate.
This implementation is only for user space SME with
driver_nl80211.c.
Previously, pairwise and group cipher suites were configured only
when kernel SME (nl80211 connect API) was used. However, mac80211
needs this information even in the user space SME case for one
thing: to disable HT when TKIP/WEP is used. Add
NL80211_ATTR_CIPHER_SUITES_PAIRWISE to fix this special case with
user space SME. This allows mac80211 to disable HT properly when
the AP is configured with configuration that is not allowed.
This add preliminary code for setting the per-STA RX GTK for
RSN IBSS when nl80211 drivers. For some reason, this does not
seem to fully work, but at least driver_nl80211.c is now aware of
what kind of key is being set and the whatever is missing from
making this key configuration go through should be specific to
nl80211/cfg80211.
When controlling multiple virtual interfaces on the same physical
radio, share the scan results events with sibling interfaces. This
decreases the time it takes to connect many virtual interfaces.
This is currently only supported on Linux with cfg80211-based
drivers when using nl80211 or wext driver interface.
Signed-off-by: Ben Greear <greearb@candelatech.com>
Some drivers are not providing exactly reliable error codes (e.g.,
with WEXT), but others may actually indicate reliable information.
Allow driver wrappers to indicate if that is the case and use
optimizations if so. For now, this improves nl80211 with
NL80211_CMD_CONNECT for a case where connection request fails.
driver_param=use_p2p_group_interface=1 can now be used to test
nl80211-drivers with separate P2P group interface. In other words,
the main interface (e.g., wlan0) is reserved for P2P management
operations and non-P2P connections and a new group interface (e.g.,
p2p-wlan0-0) is created for the P2P group.
This implementation is very minimal, i.e., it only support address
allocation for a single P2P group interface (if the driver does not
handle this internally). In addition, not all functionality has yet
been tested, so for now, this is disabled by default and needs that
special driver_param to enable.
WPA_DRIVER_FLAGS_P2P_MGMT_AND_NON_P2P flag can now be used to
indicate that the initial interface (e.g., wlan0) is used for
P2P management operations and potentially non-P2P connections.
This is otherwise identical to
WPA_DRIVER_FLAGS_P2P_DEDICATED_INTERFACE, but the possibility of
non-P2P connections makes some operations differ.
driver.h defines these functions to return 0 on success, not
number of bytes transmitted. Most callers are checking "< 0" for
error condition, but not all. Address this by following the driver
API specification on 0 meaning success.
The driver wrapper may now indicate the preferred channel (e.g., based
on scan results) on both 2.4 GHz and 5 GHz bands (and an overall best
frequency). When setting up a GO, this preference information is used
to select the operating channel if configuration does not include
hardcoded channel. Similarly, this information can be used during
GO Negotiation to indicate preference for a specific channel based
on current channel conditions.
p2p_group_add command can now use special values (freq=2 and freq=5)
to indicate that the GO is to be started on the specified band.
These are not used by any driver wrapper, i.e., only the four
data queues (BK, BE, VI, VO) are configurable. Better remove these
so that there is no confusion about being able to configure
something additional.
Pass data frames from unknown STAs to hostapd in order to reply with
a Deauthentication or Disassociation frame. This fixes compliance
with IEEE Std 802.11-2007, 11.3.
Furthermore, this does not cause a lot of overhead (at least with
mac80211 drivers) since mac80211 does not pass all data frames (but
at least from unauthenticated and unassociated STAs) to cooked monitor
interfaces.
Tested with rt2800pci on a MIPS board.
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
drivers.mak is shared between hostapd and wpa_supplicant and
compiling them together may create "wrong" flags.
Signed-off-by: Dmitry Shmidt <dimitrysh@google.com>
Add a new driver event, EVENT_INTERFACE_UNAVAILABLE, for indicating
that the driver is not able to continue operating the virtual
interface in its current mode anymore, e.g., due to operating
channel for GO interface forced to a DFS channel by another virtual
interface.
When this happens for a P2P group interface, the P2P group will
be terminated and P2P-GROUP-REMOVED event shows the reason for
this as follows:
P2P-GROUP-REMOVED wlan0 GO reason=UNAVAILABLE
If CONFIG_DRIVER_WEXT=y is not used in .config, but driver_wext.c
gets pull in to help another driver wrapper, rfkill code needs to
included to fix the build.
Listen to regulatory event messages from kernel and convert them to
internal driver event notifications indicated that the channel list
may have changed.
The driver wrapper can now indicate whether the driver supports
concurrent operations on multiple channels (e.g., infra STA connection
on 5 GHz channel 36 and P2P group on 2.4 GHz channel 1). If not,
P2P_CONNECT commands will be rejected if they would require
multi-channel concurrency.
The new failure codes for P2P_CONNECT:
FAIL-CHANNEL-UNAVAILABLE:
The requested/needed channel is not currently available (i.e., user has
an option of disconnecting another interface to make the channel
available).
FAIL-CHANNEL-UNSUPPORTED:
The request channel is not available for P2P.
The new nl80211 API means we don't need to use monitor interfaces. This
means that the P2P implementation now requires a kernel that has support
for generic management frame (not just Action frame) transmission.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This is backward compatible since older kernels will ignore the extra
attribute and only allow registration for Action frames.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
libnl has a bug, when binding more than two sockets and releasing one,
it will release the wrong address and then try to reuse it, which fails.
Therefore, we need to reimplement the socket address assignment logic
locally for libnl 1.1.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
wpa_supplicant showed signal levels incorrectly with some drivers:
Jun 6 16:29:36 rupert wpa_supplicant[18945]: Current BSS: 00:0d:97:11:40:d6
level=190
Jun 6 16:29:36 rupert wpa_supplicant[18945]: Selected BSS: 00:0d:97:11:50:09
level=192
Judging from output from other tools (iwlist) and the min_diff block
at the end of wpa_supplicant_need_to_roam, it seems these values
should actually be negative. Specifically, if one treats that number
as a signed char instead of unsigned, everything matches up.
To be honest, I've little to no understanding of wireless, but looking
at the source code for wireless-tools (iw_print_stats in iwlib.c), it
seems that the fields of the iw_quality struct need to be decoded
differently depending on various flags. I guess
src/drivers/driver_wext.c should have similar logic in
wext_get_scan_qual.
I wrote a patch that attempts to replicate some of that logic,
although it may be more complicated than is necessary; I think some of
the complexity is for backwards-compatibility, which might not be
necessary depending on wpa_supplicant's dependencies? In any case, it
is attached. Again, I don't know how any of this works, so it's likely
the patch is a bit off. But I think at least the logic to determine
min_diff in wpa_supplicant_need_to_roam would be more accurate if
level were determined correctly.
WPS 2.0 mandates the AP to include WPS IE in (Re)Association Response
if the matching (Re)Association Request included WPS IE. Provide the
needed WPS IE information to the driver_ops API for drivers that
process association frames internally.
Note: This modifies the driver_ops API by adding a new argument to
set_ap_wps_ie().
This is needed to be able to change parameters for dynamically
created interfaces between the creation of the interface and
association/start AP commands.
Following ctrl_interface commands can now be used:
P2P_SET client_apsd disable
- disable configuration (i.e., use driver default) in client mode
P2P_SET client_apsd <BE>,<BK>,<VI>,<VO>;<max SP Length>
- enable UASPD with specific trigger configuration (0/1) per AC
(max SP Length is currently ignored)
P2P_SET go_apsd disable
- disable configuration (i.e., use driver default) in AP mode
P2P_SET go_apsd <0/1>
- disable/enable APSD in AP mode
Some NDIS drivers require a workaround to allow them to associate
with a WPS AP that is already using protection (Privacy field = 1).
Let driver_ndis.c know if the AP is already using Privacy and if so,
configure a dummy WEP key to force the driver to associate.
This patch adds support for wired IEEE 802.1X client on the Solaris.
I have tested with these:
OS : OpenSolaris 2009.06
EAP : EAP-MD5
Switch : Cisco Catalyst 2950
When passing several authentication algorithms through auth_alg, we
should try all of them when the first one fails. The wext driver goes
through the connect nl80211 command and the retries are then handled by
the kernel. The nl80211 doesn't and we have to handle that from
userspace.
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
DEAUTH messages can come from a number of different sources. The one
that's hurting us currently is DEAUTH netlink messages coming to us
from compat-wireless in response to local_state_change DEAUTH messages
we sent as a part of cleaning up state in driver_nl80211's
clear_state_mismatch() function. However, DEAUTH messages can come
from a variety of unwanted sources, including directed denial-of-service
attacks (although MAC verification doesn't place that high a barrier),
so this validation is actually generically useful, I think.
The downside to this method is that without a kernel based approach
"iw dev wlan0 link" no longer works correctly after clear_state_mismatch()
is done. This will be pursued with the kernel folks.
cfg80211/mac80211 seems to be unwilling to change interface mode in
some cases. Make these less likely to cause problems by trying the
changes up to 10 times with 100 msec intervals.
Replace use of rfkill block event with rtnetlink ifdown. This makes
the design more robust since the rfkill event could have been for
another interface while the rtnetlink events are already filtered
based of ifindex. In addition, the new design handles other than
rfkill-triggered ifdown/ifup events, too. rfkill unblocked event
is still needed to try to set the interface back up. If the unblock
was for another interface, ifup will fail and the driver state is
not changed.
Setting IEEE80211_PARAM_AUTHMODE to IEEE80211_AUTH_AUTO ends up enabling
Privacy mode in the driver. We need to clear that to allow hostapd to be
reconfigured into open mode.
Previous version driver_bsd.c switches the channel in
wpa_driver_bsd_associate(). This patch changes it to use set_freq().
I have tested this patch on FreeBSD 8.0/NetBSD 5.0.2 with hostapd,
wpa_supplicant(AP) and wpa_supplicant(STA).
Add a new wpa_supplicant state: interface disabled. This can be used
to allow wpa_supplicant to be running with the network interface even
when the driver does not actually allow any radio operations (e.g.,
due to rfkill).
Allow driver_nl80211.c and driver_wext.c to start while rfkill is in
blocked state (i.e., when ifconfig up fails) and process rfkill
events to block/unblock WLAN.
There are no subdirectories in any of these directories or plans
for adding ones. As such, there is no point in running the loop
that does not do anything and can cause problems with some shells.
This adds more details into the CTRL-EVENT-DISCONNECTED event to
make it easier to figure out which network was disconnected in some
race conditions and to what could have been the reason for
disconnection. The reason code is currently only available with
the nl80211 driver wrapper.
There is no absolute requirement for separating address allocation
into separate functions, so simplify the driver wrapper interface
to use just if_add and if_remove instead of adding the new
alloc_interface_addr() and release_interface_addr() functions.
if_add() can now indicate if the driver forced a different interface
name or address on the virtual interface.
This removes transmission of some unnecessary Deauthentication
frames in cases where we only need to clear the local state. In
addition, this resolves issues for 802.11r FT-over-DS by allowing
authentication state to be set locally even when no actual
Authentication frame is to be transmitted.
This can be used to test 802.11w by sending a protected or unprotected
deauth/disassoc frame.
hostapd_cli deauth <dst addr> test=<0/1>
hostapd_cli disassoc <dst addr> test=<0/1>
test=0: unprotected
test=1: protected