Use the global control interface to remove P2P networks in
persistent_group_peer_dropped3 to support configurations that use a
dedicated P2P Device interface.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
After successfully passing the 525 tests on a remote setup mark the
tests as remote compatible.
Signed-off-by: Jonathan Afek <jonathanx.afek@intel.com>
Use the global control interface to remove P2P network blocks, to
support cases when a dedicated P2P Device interface is used.
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
Modify the persistent_group_profile_add test to support configurations
that use a dedicated P2P Device interface by sending the ADD_NETWORK and
SET_NETWORK commands on the global control interface and specifying the
P2P Device interface name.
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
The new persistent_group_peer_dropped3 test case is similar to
persistent_group_peer_dropped with the difference being in the
responding device (the one from which the persistent group information
is dropped) is not issued a separate P2P_LISTEN command and instead, a
single P2P_FIND is used through the exchange to verify that this
operation does not get stopped unexpectedly. This is a regression test
case to verify that P2P_PENDING_INVITATION_RESPONSE case ends up calling
p2p_check_after_scan_tx_continuation() in non-success case. It should be
noted that this is dependent on timing: Action frame TX request needs to
occur during the P2P_FIND Search phase (scan). As such, not every
execution of this test case will hit the previous issue sequence, but
that should be hit every now and then.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This verifies that the persistent group information gets dropped based
on peer response (unknown group) and that a new group formation can be
completed after such invitation failure.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This parameter is used only in couple of test cases and there is no need
to maintain the code to reset it in WpaSupplicant::reset().
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Verify that P2P_CANCEL gets rejected on fully re-invoked persistent
group. This did not work properly before the last couple of commits and
before this week, the P2P_CANCEL on a separate group interface in P2p
Client role could result in use of freed memory and process termination.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This allows driver-based preference list to override default operating
channel selection mechanism by using a non-social P2P find if needed.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
The dev[1] <--> dev[2] data connectivity test was using incorrect
function. dev[2] is also using a P2P group and as such, can have a
different group interface.
Signed-off-by: Jouni Malinen <j@w1.fi>
The network operations need to use the global control interface to be
performed on the interface that stores the network profiles for
persistent groups.
Signed-off-by: Jouni Malinen <j@w1.fi>
After P2P-GROUP-STARTED event, use group_form_result in order to update
the group_ifname for the device. This is needed when using P2P Device
for managing P2P operations which results in a separate group interface
being used.
Signed-off-by: Ben Rosenfeld <ben.rosenfeld@intel.com>
list_networks() always used the wlanX control interface to query for the
current list of networks. However, when a dedicated P2P Device is used,
the global control interface should be used when checking persistent
group network profiles.
Fix this by adding an optional parameter indicating that the P2P
networks are requested, and in such a case use the global control
interface.
In addition update test_p2p_persistent to use the argument when needed.
Signed-off-by: Ben Rosenfeld <ben.rosenfeld@intel.com>
This is required for cases that a dedicated P2P Device interface
is used and then the event will happen on the global interface.
Signed-off-by: Ben Rosenfeld <ben.rosenfeld@intel.com>
Send request to set persistent_reconnect on the global control
interface so it would also work when using a dedicated P2P Device
interface.
Signed-off-by: Ben Rosenfeld <ben.rosenfeld@intel.com>
Remove and re-start the persistent group manually to increase test
coverage to include the case of re-configuring the PSK list entries from
a stored persistent group.
Signed-off-by: Jouni Malinen <j@w1.fi>
This verifies P2P Client scanning behavior during group re-invocation in
a case where old scan results are not available to allow the scan to be
skipped completely.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Only run-tests.py is actually executed, so there is no need to specify
the interpreter in all the helper files and test script files.
Signed-off-by: Jouni Malinen <j@w1.fi>
The run-tests.py -l argument does not take an argument value anymore.
Instead, debug output is directed to a separate file <test>.log for each
test case.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
test_persistent_group_invite_removed_client verifies that a client
that is removed from a group can rejoin based on new invitation.
Signed-hostap: Jouni Malinen <j@w1.fi>
Jouni Malinen