Commit graph

4399 commits

Author SHA1 Message Date
Jouni Malinen
675112df1b OWE: Set PMK length properly on supplicant side
sm->pmk_len was not set when deriving the PMK as part of OWE key
generation. This depending on wpa_sm_set_pmk_from_pmksa() call resetting
the value to the default. While this worked for many cases, this is not
correct and can have issues with network profile selection based on
association information. For example, the OWE transition mode cases
would hit an issue here.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2017-10-08 17:12:35 +03:00
Sunil Dutt
63bc0ab0ed P2P: Allow GO to advertise Interworking element
This adds new wpa_supplicant configuration parameters (go_interworking,
go_access_network_type, go_internet, go_venue_group, go_venue_type) to
add a possibility of configuring the P2P GO to advertise Interworking
element.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2017-10-05 14:42:16 +03:00
vamsi krishna
e37cea308e OCE: Update default scan IEs when OCE is enabled/disabled
Update the default scan IEs when OCE is enabled/disabled to the
driver/firmware, so that the correct IEs will be sent out by the
driver/firmware in Probe Request frames.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2017-10-01 18:47:02 +03:00
Jouni Malinen
61a56c1480 Add group_mgmt network parameter for PMF cipher selection
The new wpa_supplicant network parameter group_mgmt can be used to
specify which group management ciphers (AES-128-CMAC, BIP-GMAC-128,
BIP-GMAC-256, BIP-CMAC-256) are allowed for the network. If not
specified, the current behavior is maintained (i.e., follow what the AP
advertises). The parameter can list multiple space separate ciphers.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2017-09-26 17:40:02 +03:00
Jouni Malinen
60ed2f24eb Suite B: Add tls_suiteb=1 parameter for RSA 3k key case
This adds phase1 parameter tls_suiteb=1 into wpa_supplicant
configuration to allow TLS library (only OpenSSL supported for now) to
use Suite B 192-bit level rules with RSA when using >= 3k (3072) keys.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2017-09-17 00:09:47 +03:00
Jouni Malinen
5030d7d9fd DPP: Allow raw hex PSK to be used for legacy configuration
The new psk=<hexdump> can be used as an alternative to pass=<passphrase>
when configuring the DPP Configurator with a legacy network parameters.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2017-09-15 17:54:31 +03:00
Lior David
3c7863f812 wpa_supplicant: Support dynamic update of wowlan_triggers
Previously, wowlan_triggers were updated in kernel only during startup.
Also update it whenever it is set from the control interface.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2017-09-13 22:17:58 +03:00
Lior David
3031133983 mesh: Move writing of mesh_rssi_threshold inside CONFIG_MESH
Previously, the code that writes mesh_rssi_threshold to a network block
always executes, but the code that reads it from network block and the
code that initializes it to a default value in a new network block are
inside #ifdef CONFIG_MESH. As a result when writing a config file it
will write mesh_rssi_threshold (since it has a non-default value) and
later fail to read the network block.

Fix this by moving the write code under #ifdef CONFIG_MESH as well.
Note, network blocks which already have mesh_rssi_threshold because of
the bug will still fail to read after the fix.

Signed-off-by: Lior David <qca_liord@qca.qualcomm.com>
2017-09-12 17:17:21 +03:00
Jouni Malinen
2efc672075 Fix RSN pre-authentication regression with pre-connection scan results
The introduction of radio works and a delayed callback to complete
association/connection requests ended up breaking RSN pre-authentication
candidate list generation for the case of pre-connection scan results.
Previously, wpa_supplicant_associate() set the RSN state machine
configuration before returning and the calls to
wpa_supplicant_rsn_preauth_scan_results() immediately after this
function call were working fine. However, with the radio work callback,
the RSN state machine configuration started to happen only in that
callback which would be called soon after this code path has completed.
This resulted in the RSN state machine not knowing the selected SSID and
as such, rejecting all pre-authentication candidates.

Fix this by setting the RSN state machine configuration from
wpa_supplicant_associate() so that the existing callers of
wpa_supplicant_rsn_preauth_scan_results() can be used as-is to add
candidates for pre-authentication.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2017-09-12 16:47:02 +03:00
Sabrina Dubroca
7612e65b9b mka: Add error handling for secy_init_macsec() calls
secy_init_macsec() can fail (if ->macsec_init fails), and
ieee802_1x_kay_init() should handle this and not let MKA run any
further, because nothing is going to work anyway.

On failure, ieee802_1x_kay_init() must deinit its kay, which will free
kay->ctx, so ieee802_1x_kay_init callers (only ieee802_1x_alloc_kay_sm)
must not do it. Before this patch there is a double-free of the ctx
argument when ieee802_1x_kay_deinit() was called.

Signed-off-by: Sabrina Dubroca <sd@queasysnail.net>
2017-09-10 22:23:25 +03:00
Adiel Aloni
2c66c7d115 wpa_supplicant: Check length when building ext_capability in assoc_cb
When building wpa_ie in wpas_start_assoc_cb() with ext_capab,
make sure that assignment does not exceed max_wpa_ie_len.

Signed-off-by: Adiel Aloni <adiel.aloni@intel.com>
2017-09-10 22:16:06 +03:00
Saurav Babu
cdf2501494 dbus: Add new interface property to get mesh group
Signed-off-by: Saurav Babu <saurav.babu@samsung.com>
2017-09-10 01:39:37 +03:00
Saurav Babu
190f6f1176 dbus: Add new interface property to get connected mesh peers
Signed-off-by: Saurav Babu <saurav.babu@samsung.com>
2017-09-10 01:39:37 +03:00
Saurav Babu
a9de99b1c5 dbus: Add MeshPeerDisconnected signal
This is similar to the control interface event MESH-PEER-DISCONNECTED.

Signed-off-by: Saurav Babu <saurav.babu@samsung.com>
2017-09-10 01:39:37 +03:00
Saurav Babu
9b0701fbf5 dbus: Add MeshPeerConnected signal
This is similar to the control interface event MESH-PEER-CONNECTED.

Signed-off-by: Saurav Babu <saurav.babu@samsung.com>
2017-09-10 01:39:35 +03:00
Saurav Babu
a39b040b4c dbus: Add MeshGroupRemoved signal
This is similar to the control interface event MESH-GROUP-REMOVED.

Signed-off-by: Saurav Babu <saurav.babu@samsung.com>
2017-09-09 14:12:33 +03:00
Saurav Babu
89e9cd25d2 dbus: Add MeshGroupStarted signal
This introduces a new interface for mesh and adds a signal that
is similar to the control interface event MESH-GROUP-STARTED.

Signed-off-by: Saurav Babu <saurav.babu@samsung.com>
2017-09-09 14:01:14 +03:00
Jouni Malinen
a0f19e9c74 SAE: Allow commit fields to be overridden for testing purposes (STA)
The new "SET sae_commit_override <hexdump>" control interface command
can be used to force wpa_supplicant to override SAE commit message
fields for testing purposes. This is included only in
CONFIG_TESTING_OPTIONS=y builds.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2017-09-04 13:32:03 +03:00
Jouni Malinen
a6f238f217 DPP: Add base64 dependency in makefiles
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2017-09-04 13:31:21 +03:00
Jouni Malinen
85fd8263a5 DPP: Use Transaction ID in Peer Discovery Request/Response frames
DPP tech spec changed the contents of these frames by replacing the
public key hash attributes with a Transaction ID attribute that gets
copied from the request to the response to identify the transaction in a
simpler manner.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2017-08-23 12:51:41 +03:00
Jouni Malinen
a4bf007877 DPP: Remove devices object from the connector
This was removed from the draft DPP tech spec, so remove it from the
implementation as well.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2017-08-22 23:46:27 +03:00
Avraham Stern
b5bf84ba39 WNM: Differentiate between WNM for station and for AP in build
Previously, CONFIG_WNM enabled build that supports WNM for both
station mode and AP mode. However, in most wpa_supplicant cases only
station mode WNM is required and there is no need for AP mode WNM.

Add support to differentiate between station mode WNM and AP mode
WNM in wpa_supplicant builds by adding CONFIG_WNM_AP that should be
used when AP mode WNM support is required in addition to station mode
WNM. This allows binary size to be reduced for builds that require
only the station side WNM functionality.

Signed-off-by: Avraham Stern <avraham.stern@intel.com>
2017-07-18 13:28:09 +03:00
Avraham Stern
922dcf1b45 RRM: Remove duplicate frequencies from beacon report scan request
When setting the frequencies for beacon report request scan, it is
possible that a frequency is added twice (e.g., when the same channel
appears both in the channel field and in the AP channel report
subelement). This may cause the scan request to fail.
Make sure the frequencies array contains no duplications before
requesting the scan.

Signed-off-by: Avraham Stern <avraham.stern@intel.com>
2017-07-17 18:04:34 +03:00
Avraham Stern
705e2909c6 RRM: Send response when Beacon report request is not supported/refused
Send Radio Measurement response with measurement mode set to reject
in the following cases:
 1. Reporting conditions is not supported.
 2. No valid channels found for the measurement

Sending a response with an incapable indication will stop the AP from
sending other measurement requests of the same type as specified
in IEEE Std 802.11-2016, 11.11.6.

Signed-off-by: Avraham Stern <avraham.stern@intel.com>
2017-07-17 18:00:56 +03:00
Avraham Stern
3756acfd48 RRM: Send Radio Measurement response when beacon report scan fails
When failing to trigger scan for beacon report (e.g., when the
requested duration is not supported by the driver), send a
Radio Measurement response with the mode set to refused and don't
retry the scan.

Signed-off-by: Avraham Stern <avraham.stern@intel.com>
2017-07-17 17:57:41 +03:00
Avraham Stern
b3c148e9f8 RRM: Send reject/refuse response only to unicast measurement request
IEEE Std 802.11-2016, 11.11.6 specifies that a station that is unable to
make a requested measurement or refuses to make a measurement shall
respond only if the measurement request was received within an
individually addressed radio measurement request frame, but shall not
respond if such a request was received in a group addressed frame.

Signed-off-by: Avraham Stern <avraham.stern@intel.com>
2017-07-17 17:43:32 +03:00
Dmitry Shmidt
51143af7e7 wpa_cli: Fix global control interface for STA-FIRST/STA-NEXT
If global control interface is used and wlan doesn't support P2P,
   wpa_s->global->p2p == NULL, and log shows:
wpa_supplicant: Failed to create interface p2p-dev-wlan0: -5 (I/O error)
wpa_supplicant: nl80211: Failed to create a P2P Device interface p2p-dev-wlan0
wpa_supplicant: P2P: Failed to enable P2P Device interface

Then STA-FIRST/STA-NEXT is not going to redirect to any interface,
making update_stations(ctrl_conn) is stuck in never-ending loop:

sendto(3, "STA-FIRST", 9, 0, NULL, 0)   = 9
pselect6(4, [3], NULL, NULL, {10, 0}, NULL) = 1 (in [3], left {9, 999995000})
recvfrom(3, "UNKNOWN COMMAND\n", 4095, 0, NULL, NULL) = 16
sendto(3, "STA-NEXT UNKNOWN COMMAND", 24, 0, NULL, 0) = 24
pselect6(4, [3], NULL, NULL, {10, 0}, NULL) = 1 (in [3], left {9, 999995833})
recvfrom(3, "UNKNOWN COMMAND\n", 4095, 0, NULL, NULL) = 16
sendto(3, "STA-NEXT UNKNOWN COMMAND", 24, 0, NULL, 0) = 24
pselect6(4, [3], NULL, NULL, {10, 0}, NULL) = 1 (in [3], left {9, 999995000})
recvfrom(3, "UNKNOWN COMMAND\n", 4095, 0, NULL, NULL) = 16
sendto(3, "STA-NEXT UNKNOWN COMMAND", 24, 0, NULL, 0) = 24

Signed-off-by: Dmitry Shmidt <dimitrysh@google.com>
2017-07-17 14:54:42 +03:00
Beniamino Galvani
2b9891bd6e OpenSSL: Add build option to select default ciphers
Add a build option to select different default ciphers for OpenSSL
instead of the hardcoded default "DEFAULT:!EXP:!LOW".

This new option is useful on distributions where the security level
should be consistent for all applications, as in Fedora [1]. In such
cases the new configuration option would be set to "" or
"PROFILE=SYSTEM" to select the global crypto policy by default.

[1] https://fedoraproject.org/wiki/Changes/CryptoPolicy

Signed-off-by: Beniamino Galvani <bgalvani@redhat.com>
2017-07-17 11:55:22 +03:00
Ashwini Patil
332aadb8a2 STA: Add OCE capability indication attribute
Add OCE capability indication attribute in Probe Request and
(Re)Association Request frames.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2017-07-14 21:19:53 +03:00
Vidyullatha Kanchanapally
b377ec2585 FILS: Fix issuing FILS connect to a non-FILS AP in driver-FILS case
If an AP is not FILS capable and wpa_supplicant has a saved network
block for the network with FILS key management and a saved erp info,
wpa_supplicant might end up issuing a FILS connection to a non-FILS AP.
Fix this by looking for the presence of FILS AKMs in wpa_s->key_mgmt,
i.e., after deciding on the AKM suites to use for the current
connection.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2017-07-14 21:11:35 +03:00
Ilan Peer
422570eec8 MBO: Fix possible memory leak in anqp_send_req()
In case that an mbo object is allocated, but there is a failure
to resize the wpabuf, need to free the mbo object.

Signed-off-by: Ilan Peer <ilan.peer@intel.com>
2017-07-08 16:14:03 +03:00
Avraham Stern
23eead4d74 RRM: Filter scan results by parent TSF only if driver supports it
Scan results with parent TSF older than the scan start TSF are not added
to the beacon report since they are considered as scan results from
previous scans. However, for drivers that report the scan start TSF but
not the parent TSF of each scan result, the parent TSF will be zero so
valid scan results will be dropped.

Fix this by filtering scan results by the parent TSF only if the
driver supports reporting the parent TSF for each scan result.

Signed-off-by: Avraham Stern <avraham.stern@intel.com>
2017-07-08 16:06:38 +03:00
Andrei Otcheretianski
d02e4c8ac8 P2P: Clear get_pref_freq_list_override on P2P Device
Clear the get_pref_freq_list_override in p2p_ctrl_flush(). This fixes
the case when a dedicated P2P device interface is used.

Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
2017-07-08 16:06:28 +03:00
Andrei Otcheretianski
bfbc41eace DPP: Fix compilation without openssl
dpp.h file requires openssl in order to compile, which breaks
compilation on systems without it.
Move DPP_OUI_TYPE to ieee802_11_defs.h and don't include dpp.h when
not really needed.

Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
2017-07-07 23:37:45 +03:00
Sunil Dutt
cc6088463a P2P: Allow auto GO on DFS channels if driver supports this
If a DFS forced frequency is provided in 'p2p_group_add' and the driver
supports DFS offload, the frequency was rejected in
wpas_p2p_init_go_params(). However, it was accepted in
wpas_p2p_select_go_freq() and wpas_p2p_group_add(). To make the behavior
consistent, the DFS frequency is now accepted in
wpas_p2p_init_go_params() similar to the way done in
wpas_p2p_select_go_freq().

Redundant check in wpas_p2p_group_add() for DFS forced frequency is
removed.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2017-07-07 13:49:01 +03:00
Vidyullatha Kanchanapally
fe3e0bac1f FILS: Advertize FILS capability based on driver capability
Add changes to control interface command get_capability to advertize
FILS capability, FILS AKMs suites, and FILS Authentication algorithms
based on the driver capabilities.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2017-07-07 13:39:05 +03:00
Jouni Malinen
6d49aeb762 MBO: Whitespace cleanup
Fix couple of previously missed whitespace issues.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2017-07-05 02:02:35 +03:00
Ashwini Patil
267fc0dd33 Add wpa_supplicant ctrl iface support to scan for a specific BSSID
Add support to scan for a specific BSSID through the wpa_supplicant
control interface.

Usage: wpa_cli scan bssid=ab:bc:cd🇩🇪ef:12

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2017-07-05 02:02:32 +03:00
Jouni Malinen
f522bb2377 DPP: Add DPP_CONFIGURATOR_SIGN to generate own connector
The DPP Configurator can use this new command to generate its own signed
connector for the network that it manages.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2017-07-04 17:48:44 +03:00
Jouni Malinen
484788b875 DPP: Share bootstrap type to string helper function
This can be used in hostapd as well.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2017-07-04 15:45:03 +03:00
Jouni Malinen
623f95685d DPP: Allow wpa_cli DPP_CONFIGURATOR_ADD without arguments
All the arguments to this command are optional, so do not mandate at
least one to be included in wpa_cli.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2017-07-04 15:38:52 +03:00
Jouni Malinen
787615b381 DPP: Set PMKSA expiration based on peer connector
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2017-07-03 13:29:59 +03:00
Jouni Malinen
b65b22d60a DPP: Configurator parameters in responder role
This allows wpa_supplicant to be configured to act as the configurator
in the case where a peer device initiates DPP Authentication.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2017-07-03 13:03:34 +03:00
Jouni Malinen
500ed7f006 DPP: PKEX bootstrapping
This implements genric PKEX functionality in src/common/dpp.c and glue
code to use this in wpa_supplicant (i.e, hostapd DPP implementation does
not yet support PKEX).

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2017-07-02 09:35:00 +03:00
Jouni Malinen
44d6b272cf DPP: Fix configuration item list
This was supposed to use semicolons, not commas..

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2017-07-02 09:35:00 +03:00
Ashwini Patil
b04854ceff nl80211/MBO: Set temporary disallowed BSSID list to driver
Set temporary disallowed BSSID list to the driver so that the driver
doesn't try to connect to any of the blacklisted BSSIDs during
driver-based roaming operation. This commit includes support only for
the nl80211 driver interface using a QCA vendor command for this.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2017-06-30 17:27:44 +03:00
Jouni Malinen
35f064212c DPP: Allow passphrase to be set for Configurator
The new pass=<hexdump> parameter to DPP_AUTH_INIT can now be used to
specify the passphrase to use in config object.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2017-06-23 12:46:14 +03:00
Jouni Malinen
68cb6dcec1 DPP: Allow SSID to be set for Configurator
The new ssid=<hexdump> parameter to DPP_AUTH_INIT can now be used to
specify the SSID to use in config object.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2017-06-23 12:45:25 +03:00
Jouni Malinen
a82349347d DPP: Add an example python script for QR Code operations
This script can be used to process Android logcat information for
scanned QR Codes (e.g., from Barcode Scanner app) and also to display QR
Codes for locally generated bootstrap keys.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2017-06-22 14:52:28 +03:00
Jouni Malinen
6a7182a9c3 DPP: Add DPP_BOOTSTRAP_INFO command
This can be used to fetch parsed details on bootstrapping information.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2017-06-22 14:51:21 +03:00
Jouni Malinen
8528994e21 DPP: Automatic network profile creation
wpa_supplicant can now be configured to generate a network profile
automatically based on DPP configuration. The following
dpp_config_processing values can be used to specify the behavior:
0 = report received configuration to an external program for
    processing; do not generate any network profile internally (default)
1 = report received configuration to an external program and generate
    a network profile internally, but do not automatically connect
    to the created (disabled) profile; the network profile id is
    reported to external programs
2 = report received configuration to an external program, generate
    a network profile internally, try to connect to the created
    profile automatically

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2017-06-21 18:03:34 +03:00
Jouni Malinen
da143f7fb9 FILS: Fix EVENT_ASSOC processing checks for driver-SME
Commit 5538fc9309 ('FILS: Track completion
with FILS shared key authentication offload') added an additional case
for calling wpa_supplicant_event_assoc_auth() from EVENT_ASSOC handling
in case of FILS-completion with driver-based-SME. However, that checked
what placed outside the data != NULL case while data != NULL needs to
apply for this case as well due to wpa_supplicant_event_assoc_auth()
behavior. Move the data != NULL check to apply to both cases to avoid
potentially issues if a driver interface were to return EVENT_ASSOC
without the associate data. (CID 164708)

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2017-06-19 23:36:13 +03:00
Jouni Malinen
3c0daa13d5 Make wpa_config_read_blob() easier for static analyzers
While encoded == NULL could happen in the case of an empty blob, that
will result in encoded_len == 0 and base64_decode() not derefencing the
src argument. That seems to be too difficult for some static analyzers,
so to avoid false warnings, explicitly reject the encoded == NULL case
without even trying to base64 decode it. (CID 164709)

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2017-06-19 21:30:45 +03:00
Jouni Malinen
a0d5c56f8b DPP: Network Introduction protocol for wpa_supplicant
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2017-06-19 21:13:59 +03:00
Jouni Malinen
b979caae57 DPP: Network profile parameters for DPP AKM
Extend wpa_supplicant network profile to include parameters needed for
the DPP AKM: dpp_connector, dpp_netaccesskey, dpp_netaccesskey_expiry,
dpp_csign, dpp_csign_expiry.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2017-06-19 21:13:17 +03:00
Jouni Malinen
567da5bbd0 DPP: Add new AKM
This new AKM is used with DPP when using the signed Connector to derive
a PMK. Since the KCK, KEK, and MIC lengths are variable within a single
AKM, this needs number of additional changes to get the PMK length
delivered to places that need to figure out the lengths of the PTK
components.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2017-06-19 21:13:17 +03:00
Jouni Malinen
9c2b8204e6 DPP: Integration for hostapd
This adds DPP bootstrapping, authentication, and configuration into
hostapd similarly to how the design was integrated in wpa_supplicant.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2017-06-19 21:13:17 +03:00
Jouni Malinen
9beb2892de DPP: Add wpa_cli commands for DPP operations
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2017-06-19 21:13:17 +03:00
Jouni Malinen
461d39af40 DPP: Configuration exchange
This adds support for DPP Configuration Protocol using GAS. Full
generation and processing of the configuration object is not included in
this commit.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2017-06-19 21:13:15 +03:00
Jouni Malinen
30d27b048e DPP: Authentication exchange
Add wpa_supplicant control interface commands for managing DPP
Authentication exchange.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2017-06-19 21:12:30 +03:00
Jouni Malinen
be27e185b7 DPP: Bootstrap information management
Add wpa_supplicant control interface commands for parsing the bootstrap
info URI from a QR Code (get peer public key) and to generate a new
bootstrap info with private key for local use. The optional
key=<hexdump> argument to the DPP_BOOTSTRAP_GEN command can be used to
specify the bootstrapping private key in OpenSSL ECPrivateKey DER
encoding format. This results in the local bootstrapping information
entry being created with the specified key instead of generating a new
random one.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2017-06-19 12:03:30 +03:00
Jouni Malinen
d4d76d9835 Fix offchannel TX done handling for sequence of TX frames
There could be multiple pending TX operations and if the earlier ones
have used wait_time, but the last one did not, the driver call for
canceling pending wait was not done. This could result in the driver
getting stuck waiting for the previously scheduled wait time and not
being able to do new operations until that. Fix this by canceling the
wait if any of the past offchannel_send_action() calls since the last
offchannel_send_action_done() used non-zero wait_time.

This was showing up as issues in certain DPP Public Action frame
sequences when the same offchannel operation is used with multiple
frames and the last frame in the sequence does not need wait_time.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2017-06-17 18:04:54 +03:00
Jouni Malinen
005be3daa9 Add JavaScript Object Notation (JSON) parser (RFC7159)
This is needed for DPP configuration attributes/objects.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2017-06-17 18:04:51 +03:00
Jouni Malinen
77f273c82c Extend SHA-384 and SHA-512 support to match SHA-256
The additional SHA-384 and SHA-512 functionality is needed to support
DPP with various ECC curves.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2017-06-17 18:04:12 +03:00
Jouni Malinen
2c9d924975 P2P: Debug print P2P_FIND rejection reason
This can be helpful in figuring out what happened if P2P_FIND operation
is unexpectedly rejected.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2017-06-13 14:50:51 +03:00
Wu Gao
618aa22900 P2P: Fix p2p_in_provisioning clearing in failure case
wpa_s->p2p_in_provisioning needs to be cleared when group formation
fully completes. The change to postpone GO side handling to the first
data connection in commit 41f853235f
('P2P: Extend group formation timeout on GO to first data connection')
resulted in making this not happen in one P2P Client side case: EAP-WSC
timeout in PBC case. While that is quite special case since it requires
30 second timeout without receiving new EAPOL frames and not getting
disassociation, it can apparently happen in some cases in practice. This
would result in new P2P operations (e.g., P2P_FIND) getting rejected
until wpa_supplicant is restarted.

Fix this by clearing wpa_s->p2p_in_provisioning whenever processing a
group formation failure case. For group formation success,
wpa_s->p2p_in_provisioning is left set to non-zero value to avoid
breaking the earlier limits on the GO side.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2017-06-13 14:49:36 +03:00
Vidyullatha Kanchanapally
b5db6e5dc4 eap_proxy: Support multiple SIMs in get_imsi()
This allows the eap_proxy mechanism to be used with multiple SIMs by
following the configured sim_num to index which SIM to use for when
fetching the IMSI through eap_proxy.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2017-06-06 03:42:32 +03:00
Sunil Dutt
3c2bd55f03 P2P: wpas_p2p_select_go_freq() to check for supported pref_freq
This commit is similar to the commit
783c2920cc ('P2P: Check if the pref_freq
reported by the driver supports P2P') but extends the check for
supported pref_freq to wpas_p2p_select_go_freq().

This avoids issues with P2P_GROUP_ADD ending up selecting an unexpected
channel when get_pref_freq_list() (i.e.,
QCA_NL80211_VENDOR_SUBCMD_GET_PREFERRED_FREQ_LIST) is used. Filter the
list by removing channels that do not allow P2P operation at all.
Previously, only the explicitly disallowed channels were removed and
that could have resulted in selecting an operating channel that is not
allowed for P2P and failing to complete the operation to start the
group.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2017-05-27 11:41:02 +03:00
Peng Xu
8d968351a0 Interworking: Add NULL checking for EAP name in phase2/autheap parameter
Add NULL checking for EAP name. If it is NULL, do not add the phase2
parameter autheap. This should not happen in practice due to earlier
checks for credential matching, but if there is a code path that would
allow this to be set, it is better to skip setting of the invalid value
and allow automatic selection of the Phase 2 parameters.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2017-05-26 13:20:52 +03:00
Purushottam Kushwaha
34ee12c559 Do not flush PMKSA on bssid_hint change
Change in any network configuration at runtime will cause flush to
PMKSA cache. For most of the network parameters if there is no change
in value, PMKSA flush is not performed except 'bssid' and 'priority'.

Add 'bssid_hint' to exemption list of avoiding PMKSA flush on change.
This is needed to complete change in commit
43a356b268 ('Provide option to configure
BSSID hint for a network').

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2017-05-22 13:25:49 +03:00
Vasanthakumar Thiagarajan
aa56e36d66 driver: Make DFS domain information available to core
Current DFS domain information of the driver can be used in ap/dfs
to comply with DFS domain specific requirements like uniform spreading
for ETSI domain.

Signed-off-by: Vasanthakumar Thiagarajan <vthiagar@qti.qualcomm.com>
2017-05-13 20:01:44 +03:00
Purushottam Kushwaha
43a356b268 Provide option to configure BSSID hint for a network
This exposes user configurable option to set bssid_hint for a network.
bssid_hint indicates which BSS has been found a suitable candidate for
initial association for drivers that use driver/firmware-based BSS
selection. Unlike the bssid parameter, bssid_hint does not limit the
driver from selecting other BSSs in the ESS.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2017-05-12 00:20:59 +03:00
Jouni Malinen
95818ec174 Fix compiler warning with CONFIG_IEEE80211R no-CONFIG_FILS build
Addition of remove_ies() handled the CONFIG_IEEE80211R dependency, but
missed the caller being within CONFIG_FILS as well.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2017-05-09 23:36:36 +03:00
Jaap Keuter
6136394545 Make CONFIG_MACSEC depend on IEEE8021X_EAPOL
When reducing the configuration for MACsec/MKA to the bare minimum, so
no EAP authentication, just MACsec/MKA SA use with preshared key/name,
the EAPOL engine is still needed to run the protocol for MKA. Without
any EAP authentication options the IEEE8021X_EAPOL option is not set,
resulting in a non-working Key Agreement Entity.

Therefore the CONFIG_MACSEC block needs to move up and set the
IEEE8021X_EAPOL option.

Signed-off-by: Jaap Keuter <jaap.keuter@xs4all.nl>
2017-05-08 16:28:27 +03:00
Masashi Honma
31a856a127 mesh: Make NL80211_MESHCONF_RSSI_THRESHOLD configurable
In some practical cases, it is useful to suppress joining to node in the
distance. The new field mesh_rssi_threshold could be used as RSSI
threshold for joining.

Signed-off-by: Masashi Honma <masashi.honma@gmail.com>
2017-05-08 16:23:02 +03:00
Nishant Chaprana
9f49474669 dbus: Add method to disable channel switching with a TDLS peer
This patch adds "TDLSCancelChannelSwitch" dbus method on
"fi.w1.wpa_supplicant1.Interface" interface to disable channel switching
with a TDLS peer.

Signed-off-by: Nishant Chaprana <n.chaprana@samsung.com>
2017-05-07 22:08:43 +03:00
Nishant Chaprana
2a57b4b821 dbus: Add method to enable channel switching with a TDLS peer
This patch adds "TDLSChannelSwitch" dbus method on
"fi.w1.wpa_supplicant1.Interface" interface to enable channel switching
with a TDLS peer.

Signed-off-by: Nishant Chaprana <n.chaprana@samsung.com>
2017-05-07 22:08:43 +03:00
Saurav Babu
1939505419 dbus: Add AbortScan method to abort ongoing scan
Signed-off-by: Saurav Babu <saurav.babu@samsung.com>
2017-05-07 22:08:43 +03:00
Jouni Malinen
7d440a3bc4 FILS: Derive FT key hierarchy on supplicant side for FILS+FT
Derive PMK-R0 and the relevant key names when using FILS authentication
for initial FT mobility domain association. Fill in the FT IEs in
(Re)Association Request frame for this.

Signed-off-by: Jouni Malinen <j@w1.fi>
2017-05-07 22:08:41 +03:00
Dmitry Shmidt
be1ece46f5 wpa_supplicant: Add GET_CAPABILITY for P2P redirection
It will give capability to check channel list before P2P group is
created.

Signed-off-by: Dmitry Shmidt <dimitrysh@google.com>
2017-05-05 00:43:23 +03:00
Vamsi Krishna
35bb8a9a57 Android: Define CONFIG_TESTING_OPTIONS if enabled in config
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2017-05-05 00:26:06 +03:00
Vamsi Krishna
178553b709 MBO: Add support to set ignore assoc disallow to driver
Add support to set ignore assoc disallow to the driver so that the
driver ignores assoc disallowed bit set by APs while connecting. This is
used by drivers that handle BSS selection and roaming internally.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2017-05-05 00:26:05 +03:00
Pradeep Reddy Potteti
f2a04874cf MBO: Fix possible NULL pointer dereference on candidate handling
If the driver provides input on MBO transition candidate handling, the
target value in get_mbo_transition_candidate() can be NULL if the driver
provided BSSID is not found in the wpa_supplicant BSS table. And later
it would be dereferenced. Fix this by adding an explicit check before
dereferencing the pointer.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2017-05-03 18:30:31 +03:00
Jouni Malinen
470f08b4f6 Enable CONFIG_WNM=y automatically for CONFIG_MBO=y builds
wpa_supplicant build with MBO enabled failed in CONFIG_WNM=y was not
specified explicitly. Add the WNM dependency automatically to avoid
needing explicit addition in build configuration.

Signed-off-by: Jouni Malinen <j@w1.fi>
2017-05-01 17:39:14 +03:00
Jouni Malinen
8b49b530b3 Fix CONFIG_INTERWORKING=y build without CONFIG_HS20=y
Commit 34f2851902 ('MBO: Parse MBO
ANQP-element on STA') started using the type variable outside
CONFIG_HS20 block, but forgot to remove the ifdef from the variable
declaration.

Signed-off-by: Jouni Malinen <j@w1.fi>
2017-05-01 17:39:14 +03:00
Sunil Dutt
0661163eff Do not blacklist the current AP on DISABLE_NETWORK
Disconnection due to DISABLE_NETWORK while being connected was resulting
in the AP getting blacklisted. Avoid this by setting own_disconnect_req
on a disconnect request due to DISABLE_NETWORK similarly to the
SELECT_NETWORK disconnection case.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2017-04-29 17:46:36 +03:00
Vidyullatha Kanchanapally
da6a28ba60 FILS: Specify if FILS HLP was sent in connect
This adds a string "FILS_HLP_SENT" to connect event when HLP is sent
as part of ASSOC/CONNECT request.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2017-04-29 16:35:23 +03:00
Vidyullatha Kanchanapally
a38090b16d FILS: Add HLP to Connect IEs
Add FILS HLP elements to Connect IEs and fragment them if necessary.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2017-04-29 16:35:21 +03:00
Vidyullatha Kanchanapally
1e6780bda9 Allocate dynamic memory for connect IEs
This is needed to allow new elements (e.g., FILS HLP request) to be
added.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2017-04-29 16:34:48 +03:00
Ashwini Patil
9a72bfe9a4 Add control interface command to enable/disable roaming
The new "SET roaming <0/1>" command can now be used to control
driver-based roaming.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2017-04-24 11:10:44 +03:00
Jouni Malinen
183d3924cf WPS: Add option for using random UUID
If the uuid configuration parameter is not set, wpa_supplicant generates
an UUID automatically to allow WPS operations to proceed. This was
previously always using an UUID generated from the MAC address. This
commit adds an option to use a random UUID instead. The type of the
automatically generated UUID is set with the auto_uuid parameter: 0 =
based on MAC address (default; old behavior), 1 = random UUID.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2017-04-13 17:38:55 +03:00
Vidyullatha Kanchanapally
bbe7969d63 FILS: Update cache identifier on association
This is needed when offloading FILS shared key to the drivers.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2017-04-07 18:59:12 +03:00
Vidyullatha Kanchanapally
f705f41b7f FILS: Update PMKSA cache with FILS shared key offload
Add a new PMKSA cache entry within wpa_supplicant if a driver event from
offloaded FILS shared key authentication indicates a new PMKSA entry was
created.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2017-04-07 18:46:13 +03:00
Vidyullatha Kanchanapally
01ef320f19 FILS: Update ERP next sequence number with driver offload
This keeps the internal ERP information within wpa_supplicant in sync
with the driver when offloading FILS shared key authentication.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2017-04-07 18:46:13 +03:00
Vidyullatha Kanchanapally
5538fc9309 FILS: Track completion with FILS shared key authentication offload
Update the internal fils_completed state when offloading FILS shared key
authentication to the driver.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2017-04-07 18:46:13 +03:00
Vidyullatha Kanchanapally
8b0a6dba87 FILS: Connect request for offloaded FILS shared key authentication
Add FILS/ERP parameters into the driver connect command to support FILS
shared key authentication offload.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2017-04-07 18:46:13 +03:00
Vidyullatha Kanchanapally
79f3121bb4 FILS: Set cache identifier in current PMKSA entry for driver-SME case
This was already done in sme_send_authentication() for the case where
wpa_supplicant SME is used. Similar change is needed for driver-SME to
allow FILS authentication to be offloaded to the driver.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2017-04-07 18:46:13 +03:00
Vidyullatha Kanchanapally
42e69bda2a FILS: Add support for Cache Identifier in add/remove PMKSA
Add support for setting and deleting PMKSA cache entries based on FILS Cache
Identifer. Also additionally add support for sending PMK as part of
SET_PMKSA to enable driver to derive keys in case of FILS shared key
offload using PMKSA caching.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2017-04-07 18:46:13 +03:00
Vidyullatha Kanchanapally
6fbb54140b driver: Move add_pmkid() and remove_pmkid() arguments into a struct
This makes it easier to add more arguments to these wpa_driver_ops
functions.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2017-04-07 17:03:35 +03:00
vamsi krishna
199eb3a4e6 FILS: Add support to write FILS key_mgmt values in network blocks
Add support to write FILS related key_mgmt values also while saving a
network block.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2017-04-07 16:12:41 +03:00
Jouni Malinen
af3e362fa7 FILS: Add MDE into Authentication frame for FILS+FT
When using FILS for FT initial mobility domain association, add MDE to
the Authentication frame from the STA to indicate this special case for
FILS authentication.

Signed-off-by: Jouni Malinen <j@w1.fi>
2017-04-02 13:23:34 +03:00
Jouni Malinen
c10e0ccc9e Hide *PMKSA_ADD parameters from debug log
PMKSA_ADD and MESH_PMKSA_ADD command arguments include keying material,
so show it in debug log only if requested to do with the command line -K
argument.

Signed-off-by: Jouni Malinen <j@w1.fi>
2017-04-02 12:37:33 +03:00
Shaul Triebitz
3d5f0e916d wpa_supplicant: Avoid associating to temp disabled SSID in ap_scan=2
In ap_scan=2 mode, wpa_supplicant_assoc_try() did not check whether the
SSID is temporarily disabled before trying to associate and this may
result in an infinite connect/disconnect loop. If the association
succeeds while the SSID is temporarily disabled, wpa_supplicant will
request to deauthenticate and that in turn will cause the SSID to be
temporarily disabled again. Fix that by postponing the association until
the SSID is no longer temporarily disabled.

Signed-off-by: Shaul Triebitz <shaul.triebitz@intel.com>
2017-03-29 15:03:16 +03:00
Masashi Honma
fbba28f8c5 P2P: Suppress warning on non-P2P config
Without CONFIG_P2P config, the following warning occurs if CONFIG_AP is
enabled for the build:

ap.c: In function ‘wpas_conf_ap_vht’:
ap.c:54:5: warning: unused variable ‘channel’ [-Wunused-variable]
  u8 channel = conf->channel;
     ^
ap.c:53:5: warning: unused variable ‘center_chan’ [-Wunused-variable]
  u8 center_chan = 0;
     ^

Signed-off-by: Masashi Honma <masashi.honma@gmail.com>
2017-03-27 17:21:02 +03:00
Vidyullatha Kanchanapally
6a4363f5f5 MBO: Fix reject reason codes
This change fixes the following compilation warnings:

wnm_sta.c:1007:4: warning: implicit conversion from enumeration type
 'enum mbo_transition_reason' to different enumeration type
 'enum mbo_transition_reject_reason' [-Wenum-conversion]

The actual value of both MBO_TRANSITION_REASON_UNSPECIFIED and
MBO_TRANSITION_REJECT_REASON_UNSPECIFIED is 0, so this does not result
in any change in the contents of the frames.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2017-03-26 21:13:21 +03:00
Jouni Malinen
a34317b526 GAS: Handle no-ACK TX status for GAS request frames
Previously, only the success and failure (to TX) cases were handled. It
is also possible for the driver to transmit the frame, but not receive
an ACK from the recipient. Address that by waiting for a short period of
time for a response. This fixes cases where OSU provider icon fetching
could get stuck if no ACK frame is received.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2017-03-26 21:13:21 +03:00
Jouni Malinen
31e130f82c FILS: Add FILS-SK-PFS capability into "GET_CAPABILITY fils" command
Signed-off-by: Jouni Malinen <j@w1.fi>
2017-03-13 11:46:30 +02:00
Jouni Malinen
6498351670 FILS: Check FILS Indication element against local network profile
Do not try to use FILS authentication unless the AP indicates support
for the type the local network profile enforces.

Signed-off-by: Jouni Malinen <j@w1.fi>
2017-03-12 23:23:09 +02:00
Jouni Malinen
76e20f4fa7 FILS: Add FILS SK auth PFS support in STA mode
This adds an option to configure wpa_supplicant to use the perfect
forward secrecy option in FILS shared key authentication. A new build
option CONFIG_FILS_SK_PFS=y can be used to include this functionality. A
new runtime network profile parameter fils_dh_group is used to enable
this by specifying which DH group to use. For example, fils_dh_group=19
would use FILS SK PFS with a 256-bit random ECP group.

Signed-off-by: Jouni Malinen <j@w1.fi>
2017-03-12 23:20:32 +02:00
Jouni Malinen
6115238492 OWE: Add CONFIG_OWE=y build option
This can be used to enable OWE support in hostapd and wpa_supplicant
builds.

Signed-off-by: Jouni Malinen <j@w1.fi>
2017-03-12 20:43:06 +02:00
Jouni Malinen
0a6147991e OWE: Process Diffie-Hellman Parameter element in STA mode
This adds STA side addition of OWE Diffie-Hellman Parameter element into
(Re)Association Request frame and processing it in (Re)Association
Response frame.

Signed-off-by: Jouni Malinen <j@w1.fi>
2017-03-12 19:24:11 +02:00
Jouni Malinen
09368515d1 OWE: Process Diffie-Hellman Parameter element in AP mode
This adds AP side processing for OWE Diffie-Hellman Parameter element in
(Re)Association Request frame and adding it in (Re)Association Response
frame.

Signed-off-by: Jouni Malinen <j@w1.fi>
2017-03-12 19:24:11 +02:00
Jouni Malinen
f9561868ec OWE: Add driver capability flag for OWE AKM
Signed-off-by: Jouni Malinen <j@w1.fi>
2017-03-12 19:24:11 +02:00
Jouni Malinen
a1ea1b4522 OWE: Define and parse OWE AKM selector
This adds a new RSN AKM "OWE".

Signed-off-by: Jouni Malinen <j@w1.fi>
2017-03-12 19:24:11 +02:00
Johannes Berg
b07ff9cb04 wpa_supplicant: Allow disabling HT in AP mode without HT overrides
Since VHT can be toggled explicitly, also expose being able to disable
HT explicitly, without requiring HT overrides. Continue making it
default to enabled though.

Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2017-03-11 11:11:55 +02:00
Johannes Berg
2124a615e3 wpa_supplicant: Allow explicit wide channel configuration for AP mode
Instead of deducing the wide (HT, VHT) channel configuration only
automatically in P2P mode, allow it to be configured in the network
in non-P2P mode.

Also allow all of these parameters to be configured through the control
interface or the configuration file.

Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2017-03-11 10:59:51 +02:00
Jörg Krause
57ee04dc7d wpa_cli: Execute action file in case of WPS_EVENT_TIMEOUT
Signed-off-by: Jörg Krause <joerg.krause@embedded.rocks>
2017-03-11 10:58:28 +02:00
Jörg Krause
6252b981d9 wpa_cli: Execute action file in case of WPS_EVENT_ACTIVE
Signed-off-by: Jörg Krause <joerg.krause@embedded.rocks>
2017-03-11 10:58:10 +02:00
Jörg Krause
acdf502197 WPS: Notify about WPS PBC event in Enrollee mode
Previously, the event "WPS-PBC-ACTIVE" was only generated when
wpa_supplicant is operating as WPS Registrar whereas "WPS-SUCCESS" or
"WPS-TIMEOUT" are generated for both, the Registrar and the Enrollee
roles.

Also generate the event when wpa_supplicant is operating as WPS Enrollee
to allow monitoring the begin and the end of a WPS PBC process.

Signed-off-by: Jörg Krause <joerg.krause@embedded.rocks>
2017-03-11 10:56:58 +02:00
Johannes Berg
15e5ee0b75 wpa_supplicant: events: Don't bounce timeout reason through a buffer
There's no point in making the code use a stack buffer and first copying
the string there, only to copy it again to the output. Make the output
directly use the reason string.

Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2017-03-11 10:52:43 +02:00
Avraham Stern
e97d15b733 wpa_cli: Update wnm_bss_query auto complete message
It is now possible to add neighbor configuration to wnm_bss_query.
Update the auto complete message to reflect that.

Signed-off-by: Avraham Stern <avraham.stern@intel.com>
2017-03-11 10:49:08 +02:00
Avraham Stern
15ab61eda0 WNM: Add option to configure candidates for BTM query candidate list
Add a mechanism to configure the candidates for BTM query candidate list
manually. This can be used to verify AP behavior for various candidates
preferences.

usage:
wnm_bss_query <reason> [neighbor=<BSSID>,<BSSID information>,
	                <operating class>,<channel number>,
			<PHY type>[,<hexdump of optional subelements>]]

Signed-off-by: Avraham Stern <avraham.stern@intel.com>
2017-03-11 10:47:28 +02:00
Avraham Stern
13bf18eda5 WNM: Use a dynamically allocated buffer for BTM query and response
BSS transition management query and response use a large static buffer
for the frame because the candidate list may require a lot of space.
However, in most cases the actually used space will be much less than
the buffer (since the candidate list is short or completely missing).

Use a dynamically allocated buffer instead and allocate it according
to the actual space needed.

While at it, remove unneeded filling of the MAC header in the Action
frames, since this gets ignored and wpa_drv_send_action() adds the MAC
header anyway.

Signed-off-by: Avraham Stern <avraham.stern@intel.com>
2017-03-10 23:52:44 +02:00
Jouni Malinen
34f2851902 MBO: Parse MBO ANQP-element on STA
This extends the GAS/ANQP parser in wpa_supplicant to process MBO
ANQP-elements and indicate received Cellular Data Connection Preference
values over the control interface.

When a valid MBO ANQP-element is received, the following control
interface message is sent:

RX-MBO-ANQP <BSSID> cell_conn_pref=<value>

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2017-03-10 18:57:12 +02:00
Jouni Malinen
8ecf2231fd ANQP: Extend ANQP_GET command to request without IEEE 802.11 elements
Previously, ANQP_GET required at least one IEEE 802.11 ANQP-element to
be requested. This is not really necessary, so allow a case where
num_ids == 0 as long as the request includes at least one Hotspot 2.0 or
MBO ANQP-element.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2017-03-10 17:02:22 +02:00
Avraham Stern
2316cb358c MBO: Add option to add MBO query list to ANQP query
MBO techspec v0.0_r27 changed the MBO ANQP-element format. The MBO
element in ANQP query should now include an MBO Query List element that
contains a list of MBO elements to query.

Add API to add the MBO Query List to an ANQP query.

Format:
ANQP_GET <addr> <info_id>[,<info_id>]...[,mbo:<subtype>...]

Example for querying neighbor report with MBO cellular data
connection preference:
ANQP_GET <bssid> 272,mbo:2

Signed-off-by: Avraham Stern <avraham.stern@intel.com>
2017-03-10 16:53:10 +02:00
Purushottam Kushwaha
d0330d57f3 nl80211: Add option to delay start of schedule scan plans
The userspace may want to delay the the first scheduled scan.
This enhances sched_scan to add initial delay (in seconds) before
starting first scan cycle. The driver may optionally choose to
ignore this parameter and start immediately (or at any other time).

This uses NL80211_ATTR_SCHED_SCAN_DELAY to add this via user
global configurable option: sched_scan_start_delay.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2017-03-09 15:44:26 +02:00
Jouni Malinen
b696f791ac RRM: Fix wpas_rrm_send_msr_report() loop handling
The while (len) loop was updating the next pointer at the end even when
len == 0, i.e., when the new next value won't be used. This could result
in reading one octet beyond the end of the allocated response wpabuf.
While the read value is not really used in practice, this is not correct
behavior, so fix this by skipping the unnecessary next pointer update in
len == 0 case.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2017-03-08 16:16:37 +02:00
Avraham Stern
891aa65b88 RRM: Use dynamically allocated buffer for beacon report
The maximum required size for each Beacon Report element is known in
advance: it is the size of the Beacon Report element fixed fields + the
size of the Reported Frame Body subelement.

Allocate the buffer used for constructing the Beacon Report element
dynamically with the maximum needed size, instead of using a very
large static buffer.

Signed-off-by: Avraham Stern <avraham.stern@intel.com>
2017-03-08 16:05:52 +02:00
Johannes Berg
a1f11e34c4 Use os_memdup()
This leads to cleaner code overall, and also reduces the size
of the hostapd and wpa_supplicant binaries (in hwsim test build
on x86_64) by about 2.5 and 3.5KiB respectively.

The mechanical conversions all over the code were done with
the following spatch:

    @@
    expression SIZE, SRC;
    expression a;
    @@
    -a = os_malloc(SIZE);
    +a = os_memdup(SRC, SIZE);
    <...
    if (!a) {...}
    ...>
    -os_memcpy(a, SRC, SIZE);

Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2017-03-07 13:19:10 +02:00
Kanchanapally, Vidyullatha
af8bc24da3 MBO: Add support for transition reject reason code
Add support for rejecting a BSS transition request using MBO reject
reason codes. A candidate is selected or rejected based on whether it is
found acceptable by both wpa_supplicant and the driver. Also accept any
candidate meeting a certain threshold if disassoc imminent is set in BTM
Request frame.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2017-03-07 00:34:14 +02:00
Kanchanapally, Vidyullatha
3ab484928a nl80211: Driver command for checking BTM accept/reject
Add driver interface command using the QCA vendor extensions to check
the driverr whether to accept or reject a BSS transition candidate. For
the reject case, report an MBO reject reason code.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2017-03-07 00:20:29 +02:00
Avraham Stern
23cddd7519 wpa_supplicant: Fix non_pref_chan example
The parsing code expects non_pref_chan to be non-quoted.
Fix the example in wpa_supplicant.conf not to include
quotes.

Signed-off-by: Avraham Stern <avraham.stern@intel.com>
2017-03-06 23:41:26 +02:00
Hu Wang
57d3c5913a Clear scan_res_handler on no-retry failure
Previously it was possible for wpa_s->scan_res_handler to remain set to
its old value in case wpa_drv_scan() failed and no retry for the scan
trigger was scheduled (i.e., when last_scan_req == MANUAL_SCAN_REQ).
This could result in getting stuck with the next connection attempt
after a failed "SCAN TYPE=ONLY" operation when wpa_s->scan_res_handler
was set to scan_only_handler().

Fix this by clearing wpa_s->scan_res_handler if wpa_drv_scan() fails and
no retry is scheduled.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2017-03-01 16:39:30 +02:00
Amarnath Hullur Subramanyam
e9518ae749 WFD: Add WFD R2 Subelements
Define and add support for WFD R2 Subelements.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2017-03-01 11:59:57 +02:00
Jouni Malinen
206516e8c2 af_alg: Crypto wrappers for Linux kernel crypto (AF_ALG)
CONFIG_TLS=linux can now be used to select the crypto implementation
that uses the user space socket interface (AF_ALG) for the Linux kernel
crypto implementation. This commit includes some of the cipher, hash,
and HMAC functions. The functions that are not available through AF_ALG
(e.g., the actual TLS implementation) use the internal implementation
(CONFIG_TLS=internal).

Signed-off-by: Jouni Malinen <j@w1.fi>
2017-02-28 11:24:15 +02:00
Ashwini Patil
dca4b503f1 MBO: Fix minimum length check on non_pref_chan configuration
The reason detail field in non_pref_chan attribute was removed
from MBO draft v0.0_r25. Also oper_class can be 1 character for
few country codes (e.g., country code-UK, channel number-1). So the
shortest channel configuration is 7 characters.

This was missed in the earlier commit
4a83d4b686 ('MBO: Do not add reason_detail
in non_pref_chan attr (STA)') that took care of other changes related to
removal of the reason detail.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2017-02-26 12:26:22 +02:00
Jouni Malinen
c4bb39707f Fix AES-SIV build dependencies
aes-siv.c needs functions from aes-ctr.c and aes-omac1.c, so set
NEED_AES_CTR=y and NEED_AES_OMAC1=y if NEED_AES_SIV is defined. This
fixes some build configuration combinations where either of those
dependencies were not pulled in through other parameters. For example,
some CONFIG_FILS=y cases were impacted.

Signed-off-by: Jouni Malinen <j@w1.fi>
2017-02-26 12:05:40 +02:00
Jouni Malinen
694a3a0d64 mesh: Fix CONFIG_MESH=y build without CONFIG_IEEE80211W=y
Signed-off-by: Jouni Malinen <j@w1.fi>
2017-02-26 12:05:40 +02:00
Jouni Malinen
88a447556e Fix SELECT_NETWORK freq parameter
This functionality was originally added in commit
204c9ac4ee ('Extend select_network command
with freq= to reduce scan time') re-using wpa_s->manual_scan_freqs and
MANUAL_SCAN_REQ. That got broken when commit
35d403096e ('Set NORMAL_SCAN_REQ on
SELECT_NETWORK/ENABLE_NETWORK') started overriding wpa_s->scan_req for
SELECT_NETWORK.

Fix this by adding a new scan frequency list specifically for
SELECT_NETWORK so that this does not need to depend on any specific
wpa_s->scan_req value.

Signed-off-by: Jouni Malinen <j@w1.fi>
2017-02-26 12:05:40 +02:00
Saurav Babu
d02989f2e4 D-Bus: Notify mesh capability if driver supports it
Signed-off-by: Saurav Babu <saurav.babu@samsung.com>
2017-02-26 12:05:40 +02:00
Jouni Malinen
b7286c1b5d FILS: External management of PMKSA cache entry with Cache Identifier
The PMKSA_GET and PMKSA_ADD commands can now use an optional extra
parameter to fetch and add PMKSA cache entries with the FILS Cache
Identifier.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2017-02-26 12:05:40 +02:00
Jouni Malinen
869af30728 FILS: Use FILS Cache Identifier to extend PMKSA applicability
This allows PMKSA cache entries for FILS-enabled BSSs to be shared
within an ESS when the BSSs advertise the same FILS Cache Identifier
value.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2017-02-26 12:05:40 +02:00
Jouni Malinen
6aea02e579 SME: Clear portValid on starting authentication to fix FILS
The ft_completed for FILS authentication case in
wpa_supplicant_event_assoc() depends on something having cleared
portValid so that setting it TRUE ends up authorizing the port. This
clearing part did not happen when using FILS authentication during a
reassociation within an ESS. Fix this by clearing portValid in
sme_send_authentication() just before the keys are cleared (i.e., the
old connection would not be usable anyway).

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2017-02-21 12:51:48 +02:00
Jouni Malinen
ba9774bd76 FILS: Fix BSSID in reassociation case
The RSN supplicant implementation needs to be updated to use the new
BSSID whenever doing FILS authentication. Previously, this was only done
when notifying association and that was too late for the case of
reassociation. Fix this by providing the new BSSID when calling
fils_process_auth(). This makes PTK derivation use the correct BSSID.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2017-02-21 12:26:57 +02:00
Saurav Babu
213eb18851 dbus: Set mode to mesh in bss properties when mesh is supported
Signed-off-by: Saurav Babu <saurav.babu@samsung.com>
2017-02-20 22:14:19 +02:00
Purushottam Kushwaha
3f23260da8 nl80211: Notify reason for connection timeout failure
This adds reason for timeout in event CTRL-EVENT-ASSOC-REJECT whenever
connection failure happens because of timeout. This extends the
"timeout" parameter in the event to include the reason, if available:
timeout=scan, timeout=auth, timeout=assoc.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2017-02-20 10:47:08 +02:00
Peng Xu
d512f406fc hostapd: Add IEEE 802.11ax HE IEs into Beacon/Probe Response frames
IEEE 802.11ax HE changes to include HE IEs in Beacon and Probe Response
frames. These elements are using vendor specific forms for now since the
IEEE 802.11ax draft is not yet finalized and the element contents is
subject to change.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2017-02-19 17:37:55 +02:00
Peng Xu
94380cb40a hostapd: Initial IEEE 802.11ax (HE) definitions
Add IEEE 802.11ax definitions for config, IEEE structures, and
constants. These are still subject to change in the IEEE process.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2017-02-19 17:37:52 +02:00
Masashi Honma
84ea61cffe mesh: Use correct rate in HT and legacy mixed environment
Let mesh STA A be a STA which has config disable_ht=1.
Let mesh STA B be a STA which has config disable_ht=0.
The mesh STA A and B was connected.

Previously, the mesh STA A sent frame with HT rate even though its HT
was disabled. This commit fixes the issue by checking the local BSS HT
configuration.

Signed-off-by: Masashi Honma <masashi.honma@gmail.com>
2017-02-19 16:01:17 +02:00