Commit graph

133 commits

Author SHA1 Message Date
Jouni Malinen
ec4387f9c9 Indicate CTRL-EVENT-AUTH-REJECT event on authentication rejection
This allows control interface monitors to get more detailed information
in cases where wpa_supplicant-based SME receives an Authentication frame
with non-zero status code.

Signed-off-by: Jouni Malinen <j@w1.fi>
2015-09-05 19:11:02 +03:00
Hu Wang
6108536d7d Drop connection attempt if network is disabled before radio work starts
With the radio work design, it is possible for a network entry to get
disabled (e.g., DISABLE_NETWORK <id>) during the time the connect or
sme-connect radio work waits to start. Previously, only the validity of
the BSS entry and BSSID/SSID was verified when starting the actual
connection step. Add call to wpas_network_disabled() to those checks to
catch the case where the network profile is disabled.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2015-08-10 22:16:19 +03:00
Anton Nayshtut
b36a3a65aa FST: Integration into wpa_supplicant
This commit integrates the FST into the wpa_supplicant.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2015-07-16 18:26:15 +03:00
Jouni Malinen
6a58444d27 SAE: Verify that own/peer commit-scalar and COMMIT-ELEMENT are different
This check explicitly for reflection attack and stops authentication
immediately if that is detected instead of continuing to the following
4-way handshake that would fail due to the attacker not knowing the key
from the SAE exchange.

Signed-off-by: Jouni Malinen <j@w1.fi>
2015-06-23 23:10:36 +03:00
Jouni Malinen
04e6c4cc50 Fix SAE group selection in an error case
The sae_groups parameter is zero terminated array, not -1 terminated, so
must check the value against <= 0 to break out from the loop.

Signed-off-by: Jouni Malinen <j@w1.fi>
2015-06-20 23:29:57 +03:00
Jouni Malinen
ee140ef98f FT: Stop association attempt if Auth response processing fails (SME)
Call the FT processing function directly instead of going through
wpa_supplicant_event() to process FT Authentication frame in SME case.
This allows parsing error to be used to trigger immediate failure for
the connection instead of trying to proceed to reassociation step that
cannot succeed.

Signed-off-by: Jouni Malinen <j@w1.fi>
2015-06-20 17:36:58 +03:00
Jouni Malinen
59b416c733 Add optional reassoc-to-same-BSS optimization
The new reassoc_same_bss_optim=1 configuration parameter can now be used
to request wpa_supplicant to bypass the unnecessary Authentication frame
exchange when reassociating back to the same BSS with which the device
is already associated. This functionality is disabled by default since
it may cause undesired interoperability issues with some APs.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2015-02-19 16:35:39 +02:00
Jouni Malinen
ba4226130e Simplify eapol_sm_notify_pmkid_attempt()
Drop the unneeded 'attempt' argument. This was originally used for
indicating an aborted PMKID caching attempt, but a fix in 2006 removed
the only such user and since that time, only attempt == 1 has been used.

Signed-off-by: Jouni Malinen <j@w1.fi>
2015-01-28 13:09:31 +02:00
Jouni Malinen
3f56a2b746 Ignore pmf=1 default if driver does not support PMF
Connection with a PMF enabled AP will fail if we try to negotiate PMF
while the local driver does not support this. Since pmf=1 does not
require PMF for a successful connection, it can be ignored in such a
case to avoid connectivity issues with invalid configuration. This makes
it somewhat easier to allow upper layer programs to use pmf=1 default
regardless of driver capabilities.

Signed-off-by: Jouni Malinen <j@w1.fi>
2015-01-27 12:38:52 +02:00
Jouni Malinen
d29fa3a767 Extend VENDOR_ELEM parameters to cover non-P2P Association Request
The new VENDOR_ELEM value 13 can now be used to add a vendor element
into all (Re)Association Request frames, not just for P2P use cases like
the previous item was for.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2015-01-14 01:12:56 +02:00
Jouni Malinen
4e70bbf1c6 SAE: Clear keys from memory on disassociation
There is no need to keep temporary keys in memory beyond the end of the
association, so explicitly clear any SAE buffers that can contain keys
as soon as such keys are not needed.

Signed-off-by: Jouni Malinen <j@w1.fi>
2014-12-29 20:00:02 +02:00
Jouni Malinen
d97a3c4885 SME: Optimize OBSS scanning
Include only the potentially affected channel range in OBSS scans to
reduce the amount of offchannel time needed for scanning when requested
by the AP.

Signed-off-by: Jouni Malinen <j@w1.fi>
2014-12-22 22:07:03 +02:00
Jouni Malinen
267ac3bcd6 Add more debug prints for WPA/RSN selection issues for connection
ap_ft_sae test case managed to hit a somewhat unclear error case which
resulted in "WPA: Failed to select WPA/RSN" print and not enough
information to figure out what exactly had went wrong.

Signed-off-by: Jouni Malinen <j@w1.fi>
2014-12-22 13:49:52 +02:00
Jouni Malinen
81648d0041 SAE: Report connection failure if SME cannot build auth frame
Instead of just stopping connection process and network discovery,
report SAE failures to build Authentication frames (e.g., due to missing
password) as a connection failure to get the normal retry mechanism into
use.

Signed-off-by: Jouni Malinen <j@w1.fi>
2014-12-14 16:48:38 +02:00
Masashi Honma
a959a3b69d SAE: Fix Anti-Clogging Token request frame format
This commit inserts Finite Cyclic Group to Anti-Clogging Token request
frame because IEEE Std 802.11-2012, Table 8-29 says "Finite Cyclic Group
is present if Status is zero or 76".

Signed-off-by: Masashi Honma <masashi.honma@gmail.com>
2014-11-25 16:08:53 +02:00
Jouni Malinen
849367afe9 SME: Fix a sign-compare warning
Signed-off-by: Jouni Malinen <j@w1.fi>
2014-11-25 01:07:16 +02:00
Andrei Otcheretianski
70d1e72849 wpa_supplicant: Handle link measurement requests
Send link measurement response when a request is received. Advertise
only RCPI, computing it from the RSSI of the request. The TX power field
is left to be filled by the driver. All other fields are not published.

Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
2014-11-22 21:45:07 +02:00
Assaf Krauss
b361d580ec SME: Add RRM support to association request
In case the AP we are associating with advertises support for RRM,
advertise our own RRM support in the (Re)Association Request frame. This
is done by adding an RRM Capabilities IE. The underlying driver is
expected to further add a Power Capabilities IE to the request, and set
the Radio Measurement flag in the Capability Info field. At this point
the RRM Capabilities IE advertises no measurement support.

Signed-off-by: Assaf Krauss <assaf.krauss@intel.com>
2014-11-22 21:13:45 +02:00
Jouni Malinen
a7f5271d52 Update pending connect radio work BSS pointer on scan update
It is possible for scan result processing or BSS entry removal to occur
while there is a pending connect or sme-connect radio work with a
previously selected BSS entry. The BSS pointer was previously verified
to be valid, i.e., still point to a BSS entry, at the time the actual
connection operation is started. However, that BSS entry could have
changed to point to another BSS if the old BSS entry was either removed
or reallocated and a new BSS entry was added at the same location in
memory. This could result in the connection attempt failing to configure
parameters properly due to different BSS information (e.g., different
BSSID).

Fix this by updated the pending connect radio work data on BSS entry
updates similarly to how the last_scan_res array was updated. If the
selected BSS entry is removed, this will still result in a failed
connection, but reallocated BSS entry is now followed properly and used
when the connection work starts.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2014-10-28 00:43:58 +02:00
Jouni Malinen
bc26ac50dd SAE: Add support for PMKSA caching on the station side
This makes wpa_supplicant SME create PMKSA cache entries from SAE
authentication and try to use PMKSA caching if an entry is found for the
AP. If the AP rejects the attempt, fall back to SAE authentication is
used.

Signed-off-by: Jouni Malinen <j@w1.fi>
2014-10-18 13:02:02 +03:00
Janusz Dziedzic
4ec68377ef wpa_supplicant: Use hostapd_freq_params in assoc_params
Use hostapd_freq_params instead of simple frequency parameter for driver
commands. This is preparation for IBSS configuration to allow use of
HT/VHT in IBSS.

Signed-off-by: Janusz Dziedzic <janusz.dziedzic@tieto.com>
2014-10-04 18:43:42 +03:00
Jouni Malinen
cb5ef952c8 SME: Verify that os_get_random() succeeds for SA Query
Be more consistent on checking os_get_random() return value (CID 72706).

Signed-off-by: Jouni Malinen <j@w1.fi>
2014-09-07 18:27:42 +03:00
Jouni Malinen
745ef18478 HS 2.0: Verify assoc_req_ie buffer size for indication elements
While the buffer is expected to be large enough for all the IEs, it is
better to check for this explicitly when adding the HS 2.0 Indication
element. (CID 68601)

Signed-off-by: Jouni Malinen <j@w1.fi>
2014-07-02 12:38:48 +03:00
Johannes Berg
57a8f8af38 nl80211: Use low-priority scan for OBSS scan
Some drivers may support low-priority scans, if they do then
use that for OBSS scanning.

Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2014-06-22 00:47:06 +03:00
Jouni Malinen
3302b7c29f Rate limit SA Query procedure initiation on unprotected disconnect
There is no need to trigger new SA Query procedure to check the state of
the connection immediately after having performed such a check. Limit
the impact of burst of unprotected Deauth/Disassoc frames by starting a
new SA Query procedure only once at least 10 seconds has passed from the
previous SA Query that was triggered by reception of an unprotected
disconnection. The first SA Query procedure for each association does
not follow this rule to avoid issues with test cases that expect to see
an SA Query every time.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2014-06-19 20:56:32 +03:00
Jouni Malinen
0bbaa9b93f Validate driver extended capabilities length against buffer length
Prepare for new extended capabilities bits by checking that the local
buffer is large enough to contain all the bits the driver requests. The
existing buffers are large enough to include anything defined until now,
but it would be possible to add more definitions in the future, so
increase them a bit as well to make this more future proof.

Signed-off-by: Jouni Malinen <j@w1.fi>
2014-06-07 16:35:30 +03:00
Ilan Peer
d0df643735 wpa_supplicant: Call frequency conflict handling during auth
Previously, the frequency conflict was handled only during the
association flow. However, some drivers, e.g., mac80211 based
drivers, will fail an authentication request in case that there
are no available channels for use (as they might be used by
other interfaces), and thus the frequency conflict resolution
is never called.

Fix this by calling frequency conflict resolution during
authentication (SME-in-wpa_supplicant) as well.

In addition, get the shared radio frequency from the wpa_s context in
both the SME-in-driver and SME-in-wpa_supplicant cases and not from the
driver.

Signed-off-by: Ilan Peer <ilan.peer@intel.com>
2014-04-24 12:15:32 +03:00
Ilan Peer
f1c4dbf5cd wpa_supplicant: Remove pending sme-connect radio work
If a new connection is attempted while there is a pending sme-connection
radio work, cancel the pending radio work and continue with the new
connection attempt. This is preferable over rejecting the new work and
continuing with the pending one, as it is possible that the previous
work is no longer valid.

Signed-off-by: Ilan Peer <ilan.peer@intel.com>
2014-03-27 16:45:25 +02:00
Jouni Malinen
163f801ef2 nl80211: Indicate HS 2.0 OSEN AKM in connect/associate command
This allows drivers that build the WPA/RSN IEs internally to use similar
design for building the OSEN IE.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2014-03-25 18:33:21 +02:00
Jouni Malinen
31ded52e70 SME: Add more debug prints for OBSS scans and 20/40 MHz co-ex report
This makes it easier to debug wpa_supplicant behavior when reporting
20/40 MHz co-ex information based on OBSS scans.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2014-03-23 23:56:50 +02:00
Jouni Malinen
7f8eb34dee SME: Fix OBSS scan result processing for 20/40 MHz co-ex report
The 40 MHz intolerant bit needs to be checked before skipping the BSS
based on the channel already being in the lost (which could have
happened due to another BSS that does not indicate 40 MHz intolerant).
This fixed the 20/40 MHz co-ex report to indicate 20 MHz request
properly if there are both 40 MHz tolerant and intolerant BSSes on the
same channel.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2014-03-23 23:54:50 +02:00
Jouni Malinen
df0f01d91f HS 2.0R2: Add OSEN client implementation
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
2014-02-26 01:24:23 +02:00
Jouni Malinen
f9cd147d6b HS 2.0R2: Update Indication element to Release 2
The HS 2.0 Indication element from wpa_supplicant now includes the
release number field and wpa_supplicant shows the release number of the
AP in STATUS command (hs20=1 replaced with hs20=<release>).

The new update_identifier field in the cred block can now be used to
configure the PPS MO ID so that wpa_supplicant adds it to the Indication
element in Association Request frames.

Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
2014-02-26 01:24:22 +02:00
Jouni Malinen
f0e30c8410 Do not start another connect work while one is pending
It was possible for the connect or sme-connect radio work to get
re-scheduled while an earlier request was still pending, e.g.,
select_network is issued at the moment a scan radio work is in progress
and the old scan results are recent enough for starting the connection.
This could result in unexpected attempt to re-associate immediately
after completing the first connection.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2014-02-24 15:22:35 +02:00
Andrei Otcheretianski
b3253ebb73 wpa_supplicant: Complete radio works on disable event
While testing rfkill blocking of a scanning interface, it
was seen that the ongoing scan never completes. This happens
since EVENT_SCAN_RESULTS is discarded on a disabled interface.

Fix this and also other possible radio work completion issues
by removing all the radio works (including started) of the
disabled interface.

To be able to remove already started radio works, make their
callbacks be reentrant with deinit flag (when the work
is started), so each radio work should be able to handle
its own termination.

Signed-hostap: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
2014-02-16 00:06:23 +02:00
Jouni Malinen
d950477913 Fix authentication algorithm negotiation in SME code
Commit 6ac4b15ef8 (wpa_radio work for
connection) caused a regression for cases where multiple auth_alg values
are set in a network block and wpa_supplicant-based SME is supposed to
iterate through them. The connection radio work was not terminated when
receiving authentication failure and this resulted in the following
authentication attempt failing.

Signed-hostap: Jouni Malinen <j@w1.fi>
2014-02-03 19:34:33 +02:00
Jouni Malinen
6ac4b15ef8 Use wpa_radio work for connection
This protects against conflicting offchannel operations during
connection (authentication, association, EAP exchanges, 4-way
handshake).

Signed-hostap: Jouni Malinen <j@w1.fi>
2014-01-07 10:45:09 +02:00
Jouni Malinen
4848a38d85 Get rid of duplicated cipher suite and AKM definitions
WPA_CIPHER_* and CIPHER_* are used for the exact same set of cipher
suites with the main difference being that the WPA_CIPHER_* version is
suitable to be used as a bitfield. Similarly, WPA_KEY_MGMT_* and
KEY_MGMT_* have similar design for AKMs. There is no need to maintain
two separate copies of the definitions since the bitfield compatible
version can be used for both needs. Get rid of the CIPHER_* and
KEY_MGMT_* versions to clean up the implementation by getting rid of
unnecessary mapping functions.

Signed-hostap: Jouni Malinen <j@w1.fi>
2013-12-31 09:16:27 +02:00
Johannes Berg
46b8d4c004 wpa_supplicant: Use monotonic time for SA query timeout
The SA query timeout is just a regular timeout (currently
hard-coded to 1000 TU), so use monotonic time for it.

Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2013-12-24 07:17:25 +02:00
Jouni Malinen
18ca733248 SAE: Fix group selection
Number of regressions had shown up in wpa_supplicant implementation of
SAE group selection due to different integer array termination (-1 in
hostapd, 0 in wpa_supplicant) being used for SAE groups. The
default_groups list did not seem to use any explicit termination value.
In addition, the sae_group_index was not cleared back to 0 properly
whenever a new SAE session was started.

Signed-hostap: Jouni Malinen <j@w1.fi>
2013-11-02 18:07:49 +02:00
Jouni Malinen
d7df0fa727 Clean up wpa_supplicant_event() with deauth/disassoc helper functions
wpa_supplicant_event() has grown overly large, so it is useful to split
it into smaller pieces.

Signed-hostap: Jouni Malinen <j@w1.fi>
2013-07-21 16:40:40 +03:00
Jouni Malinen
55a2df4389 HS 2.0: Include HS 2.0 Indication element only for HS 2.0 association
The Hotspot 2.0 specification seems to mandate this element to be
included in all (Re)Association Request frames if the station is Hotspot
2.0 capable. However, that results in conflicts with other requirements
like no TKIP use when this element is present. The design is really
supposed to include the indication element only for Hotspot 2.0
associations regardless of what the current specification implies.
Remove the HS 2.0 Indication element from (Re)Association Request frame
whenever the connection is not for Hotspot 2.0 purposes.

Signed-hostap: Jouni Malinen <j@w1.fi>
2013-05-05 16:29:21 +03:00
Jouni Malinen
e864c0aefe Use a common frequency to channel conversion function
Signed-hostap: Jouni Malinen <j@w1.fi>
2013-04-27 22:11:51 +03:00
Chet Lanctot
3ee9ade6cf Allow SME SA Query to be used by all drivers
The unprotected disconnection events were previously processed only for
drivers that used the wpa_supplicant SME implementation (separate
authentication and association commands). However, this can be useful
for drivers that use the connect API, so remove the limitation and allow
the same IEEE 802.11w SA Query mechanism to be used even without full
use of the wpa_supplicant SME.

Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
2013-03-11 13:49:40 +02:00
Johannes Berg
e9ee8dc394 wpa_supplicant: Support VHT capability overrides
Add support for VHT capability overrides to allow testing connections
with a subset of the VHT capabilities that are actually supported by
the device. The only thing that isn't currently supported (by mac80211
and this code) is the RX/TX highest rate field.

Signed-hostap: Johannes Berg <johannes.berg@intel.com>
2013-03-10 18:04:39 +02:00
Jouni Malinen
62769a88db Move cipher to enum wpa_cipher conversion into wpa_common.c
Signed-hostap: Jouni Malinen <j@w1.fi>
2013-01-13 18:02:20 +02:00
Jouni Malinen
b4fd3613d3 SAE: Free temporary buffers when moving to Accepted state
Most of the variables are not needed anymore once the SAE instance
has entered Accepted state. Free these to save memory.

Signed-hostap: Jouni Malinen <j@w1.fi>
2013-01-12 17:51:54 +02:00
Jouni Malinen
4ef34a9960 SAE: Remove duplicated SAE field debug dumps
Signed-hostap: Jouni Malinen <j@w1.fi>
2013-01-12 17:51:54 +02:00
Jouni Malinen
625f202a74 SAE: Allow enabled groups to be configured
hostapd.conf sae_groups parameter can now be used to limit the set of
groups that the AP allows for SAE. Similarly, sae_groups parameter is
wpa_supplicant.conf can be used to set the preferred order of groups. By
default, all implemented groups are enabled.

Signed-hostap: Jouni Malinen <j@w1.fi>
2013-01-12 17:51:53 +02:00
Jouni Malinen
a46d72d7d7 SAE: Maintain EC group context in struct sae_data
This can be used to share same EC group context through the SAE
exchange.

Signed-hostap: Jouni Malinen <j@w1.fi>
2013-01-12 17:51:52 +02:00