Commit graph

12 commits

Author SHA1 Message Date
Masashi Honma
449d63d6b7 mesh: Fix memory leak on error path
Signed-off-by: Masashi Honma <masashi.honma@gmail.com>
2015-09-05 21:31:25 +03:00
Masashi Honma
a5d2bf2473 mesh: Fix segfault on error path
When wpa_init() in __mesh_rsn_auth_init() failed, empty rsn->auth caused
segmentation fault due to NULL pointer dereference when wpa_deinit() was
called. Fix this by checking the pointer before executing deinit steps.

Signed-off-by: Masashi Honma <masashi.honma@gmail.com>
2015-09-05 21:31:25 +03:00
Masashi Honma
8a51dcbc2f mesh: Rename IE field to clarify its use
This is used only for RSNE.

Signed-off-by: Masashi Honma <masashi.honma@gmail.com>
2015-09-05 21:15:53 +03:00
Masashi Honma
bf51f4f82b mesh: Fix remaining BLOCKED state after SAE auth failure
When SAE authentication fails, wpa_supplicant retries four times. If all
the retries result in failure, SAE state machine enters BLOCKED state.
Once it enters this state, wpa_supplicant doesn't retry connection. This
commit allow connection retries even if the state machine entered
BLOCKED state.

There could be an opinion "Is this patch needed? User could know the SAE
state machine is in the BLOCKED mode by MESH-SAE-AUTH-BLOCKED event.
Then user can retry connection. By user action, SAE state machine can
change the state from BLOCKED to another.". Yes, this is a true at the
joining mesh STA. However, a STA that is already a member of existing
mesh BSS should not retry connection because if the joining mesh STA
used wrong password, all the existing STA should do something from UI to
retry connection.

Signed-off-by: Masashi Honma <masashi.honma@gmail.com>
2015-02-08 12:43:24 +02:00
Masashi Honma
79ddb2062e mesh: Add a monitor event on SAE authentication getting blocked
Send MESH-SAE-AUTH-BLOCKED event if SAE authentication is blocked. The
BLOCK state will finish when a new peer notification event is sent for
the same MAC address.

Signed-off-by: Masashi Honma <masashi.honma@gmail.com>
2015-02-07 22:33:23 +02:00
Masashi Honma
dd2cbafc89 mesh: Add a monitor event for SAE authentication failure
SAE authentication fails likely with wrong password. This commit adds a
notification of the failure to the upper application (UI) so that the
application can notify suspection of a wrong password to the user. The
control interface monitor even for this is "MESH-SAE-AUTH-FAILURE
addr=<peer>".

Signed-off-by: Masashi Honma <masashi.honma@gmail.com>
2015-02-07 22:23:34 +02:00
Masashi Honma
871ff0b746 mesh: Sync plink state with kernel
The plink_state exists both wpa_supplicant and kernel. Synchronize them
with wpa_mesh_set_plink_state().

Signed-off-by: Kenzoh Nishikawa <Kenzoh.Nishikawa@jp.sony.com>
Signed-off-by: Masashi Honma <masashi.honma@gmail.com>
2015-01-28 13:09:31 +02:00
Bob Copeland
a206e2a175 SAE: Centralize function for sending initial COMMIT
When performing SAE authentication in mesh, one station may
initiate authentication by sending a COMMIT as soon as a peer
candidate is discovered. Previously we did this in mesh_rsn.c,
but this left some of the state initialization in a different
part of the code from the rest of the state machine, and we may
need to add other initializations here in the future, so move
that to a more central function.

Signed-off-by: Bob Copeland <me@bobcopeland.com>
2015-01-10 11:43:29 +02:00
Jouni Malinen
a193231dfb Clean up debug prints to use wpa_printf()
This converts most of the remaining perror() and printf() calls from
hostapd and wpa_supplicant to use wpa_printf().

Signed-off-by: Jouni Malinen <j@w1.fi>
2014-12-26 13:20:57 +02:00
Jouni Malinen
608b0ff52a mesh: Check for initialization failures
It is possible that these location ended up getting called before mesh
startup operations had been completed and that could result in
dereferencing NULL pointers. Address those error cases by verifying that
the needed parameters are available before using them.

Signed-off-by: Jouni Malinen <j@w1.fi>
2014-11-30 15:53:11 +02:00
Chun-Yeow Yeoh
c596f3f083 mesh: Add timer for SAE authentication in RSN mesh
Add timer to do SAE re-authentication with number of tries defined
by MESH_AUTH_RETRY and timeout defined by MESH_AUTH_TIMEOUT.

Ignoring the sending of reply message on "SAE confirm before commit"
to avoid "ping-pong" issues with other mesh nodes. This is obvious when
number of mesh nodes in MBSS reaching 6.

Signed-off-by: Chun-Yeow Yeoh <yeohchunyeow@gmail.com>
Signed-off-by: Bob Copeland <me@bobcopeland.com>
2014-11-16 19:43:11 +02:00
Thomas Pedersen
0f950df029 mesh: Add mesh robust security network
This implementation provides:

- Mesh SAE authentication mechanism
- Key management (set/get PSK)
- Cryptographic key establishment
- Enhanced protection mechanisms for robust management frames

Signed-off-by: Javier Lopez <jlopex@gmail.com>
Signed-off-by: Javier Cardona <javier@cozybit.com>
Signed-off-by: Jason Mobarak <x@jason.mobarak.name>
Signed-off-by: Thomas Pedersen <thomas@noack.us>
2014-11-16 19:43:06 +02:00