Replace direct wpa_msg() calls with p2p_dbg(), p2p_info(), and p2p_err()
calls that use a new debug_print() callback to handle actual debug
printing outside the P2P module.
Signed-hostap: Jouni Malinen <j@w1.fi>
As per P2P specification v1.2: "The P2P Group Info attribute shall be
omitted if there are zero connected P2P Clients."
Do not add the attribute if there are not connected peers.
Signed-hostap: Chaitanya T K <chaitanya.mgit@gmail.com>
It is possible for a P2P client to connect to an operating group without
exchanging any Probe Request/Response frames that would allow the GO to
discover the peer. To make sure there is a P2P peer entry at the GO, try
to add the peer information based on P2P IE in (Re)Association Request
frame.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
Commit 1a9f6509b3 added support for
fragmenting the P2P IE in Probe Response frames from a GO. However, it
did not take into account the possibility of Wi-Fi Display IE being
included in the same buffer and caused a regression for the cases where
Wi-Fi Display is enabled. Fix this by building the possibly fragmented
P2P IE first and then concatenating the separate IEs together.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
This commit increases the maximum buffer size for P2P Client Info
advertized by the Group Owner in the Probe Response frames.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
This commit adds control interface commands and internal storage of
Wi-Fi Display related configuration. In addition, WFD IE is now added
to various P2P frames, Probe Request/Response, and (Re)Association
Request/Response frames. WFD subelements from peers are stored in the
P2P peer table.
Following control interface commands are now available:
SET wifi_display <0/1>
GET wifi_display
WFD_SUBELEM_SET <subelem> [hexdump of length+body]
WFD_SUBELEM_GET <subelem>
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
Concurrent Operation bit was not set for GO even if the device
supports concurrent operations. Make sure the Device Capability
value is consistent with other P2P use cases by using the value
determined in p2p_init().
Signed-hostap: Masashi Honma <masashi.honma@gmail.com>
This can be used with P2P management operations that need to verify
whether the local device is operating a specific group based on
P2P Group ID attribute from a peer.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
Remove the GPL notification text from files that were initially
contributed by Atheros Communications or Qualcomm Atheros.
Signed-hostap: Jouni Malinen <j@w1.fi>
Even though we may not receive a Probe Response from the peer during
the connection, we should not be expiring a P2P peer entry while that
peer is connected to a group where we are the GO.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
The Device ID attribute was already used in Listen state, but it was
ignored in GO role. Verify that there is a match with Device ID in
GO rule, too, before replying to the Probe Request frame.
Signed-hostap: Jouni Malinen <j@w1.fi>
It is safer to assume that the driver could be using NoA and reject
any Presence Request unless we are sure that noa NoA is in use.
Signed-hostap: Jouni Malinen <j@w1.fi>
If a P2P client associates with the group while it is
already associated, two member entries may be added to
the group which also confuses num_members counting.
Deal with this by removing the existing entry first
before adding a new one.
I think the way Reinette ran into this was due to our
tx_sync implementation in iwlagn, mac80211 might have
queued two association frames thinking the first one
just failed, but both only went out after the sync was
really successful (which tx_sync doesn't wait for).
Reported-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-hostap: Johannes Berg <johannes.berg@intel.com>
For P2P, the p2p_connect takes in device address argument to make a
connection. However the connected event AP-STA-CONNECTED comes with
interface address. The application listening on events would find it
difficult to map interface address to the p2p device address which is
provided for connection.
Append P2P Device Address to AP-STA-CONNECTED event for P2P Client
connection. This will help applications to easily map the P2P Interface
Address to P2P Device Address on CONNECTED event. For non-P2P case, it
will just print the usual STA MAC address alone.
Signed-off-by: Jithu Jance <jithu@broadcom.com>
The persistent_reconnect configuration parameter was used to decide
whether to accept invitation to re-establish a persistent group.
However, this was not being advertised in the Group Capability bitmap.
Add the Persistent Reconnect bit based on this configuration to GO
Negotiation frames and Beacon/Probe Response frames from the GO.
This currently unused function would have triggered wpabuf overflows
due to incorrect variable being reset to zero in the case the old
NoA wpabuf was large enough for the new data.
Some new code will require access to P2P group members, so add API to
retrieve the number of members and iterate the members themselves.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
A new configuration parameter, p2p_group_idle, can now be used to set
idle timeout value for P2P groups in seconds (0 = no timeout). If set,
this values is used to remove P2P group (both GO and P2P client)
interfaces after the group has been idle (no clients/GO seen) for the
configuration duration.
The P2P-GROUP-REMOVED event is now indicating the reason for group
removal when known. For example:
P2P-GROUP-REMOVED wlan0 GO reason=REQUESTED
P2P-GROUP-REMOVED wlan1 client reason=IDLE
The P2P group component is now tracking of associated stations
in the group and the Group Limit bit in the Group Capabilities
is updated based on whether there is room for new clients in
the group.
This can happen, e.g., when a P2P client connects to a P2P group
using the infrastructure WLAN interface instead of P2P group
interface. In that case, the P2P client may behave as if the GO
would be a P2P Manager WLAN AP.
If enabled, cross connection allows GO to forward IPv4 packets
using masquerading NAT from the P2P clients in the group to an
uplink WLAN connection. This is disabled by default and can be
enabled with "wpa_cli p2p_set cross_connect 1" on the P2P device
interface.
While there is no real value in this, the spec seems to mark this
attribute as mandatory from GO, so better included it regardless
of whether we have clients or not (the attribute is empty in case
no clients are connected).
