This is an initial step in allowing the ANQP responses to be shared
among multiple BSSes if the BSSes are determined to be operating under
identical configuration.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
If the REMOVE_NETWORK command is used to delete the currently connected
network, some operations were run between removing the network and
clearing of wpa_s->current_ssid. This left wpa_s->current_ssid pointing
to freed memory and should any operation end up using it before the
pointer gets cleared, freed memory could be references. Avoid this by
removing the network only after having completed the operations that
clear wpa_s->current_ssid.
Signed-hostap: Deepthi Gowri <deepthi@codeaurora.org>
intended-for: hostap-1
The freq and ht40 parameters can now be used with the p2p_invite
command when reinvoking a persistent group as the GO.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
wpa_cli p2p_serv_disc_req command can now be used to request WSD
request to be sent to specified or all peers who support WSD.
format: wifi-display <list of roles> <list of subelements>
examples:
p2p_serv_disc_req 00:00:00:00:00:00 wifi-display [source] 2,3,4,5
p2p_serv_disc_req 02:01:02:03:04:05 wifi-display [pri-sink] 3
p2p_serv_disc_req 00:00:00:00:00:00 wifi-display [sec-source] 2
p2p_serv_disc_req 00:00:00:00:00:00 wifi-display [source+sink] 2,3,4,5
p2p_serv_disc_req 00:00:00:00:00:00 wifi-display [source][pri-sink] 2,3,4,5
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
This commit adds control interface commands and internal storage of
Wi-Fi Display related configuration. In addition, WFD IE is now added
to various P2P frames, Probe Request/Response, and (Re)Association
Request/Response frames. WFD subelements from peers are stored in the
P2P peer table.
Following control interface commands are now available:
SET wifi_display <0/1>
GET wifi_display
WFD_SUBELEM_SET <subelem> [hexdump of length+body]
WFD_SUBELEM_GET <subelem>
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
This allows both hostapd and wpa_supplicant to be used to derive and
configure keys for GCMP. This is quite similar to CCMP key
configuration, but a different cipher suite and somewhat different rules
are used in cipher selection. It should be noted that GCMP is not
included in default parameters at least for now, so explicit
pairwise/group configuration is needed to enable it. This may change in
the future to allow GCMP to be selected automatically in cases where
CCMP could have been used.
This commit does not included changes to WPS or P2P to allow GCMP to be
used.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
The new gas_request and gas_response_get commands can be used to request
arbitary GAS queries to be performed. These can be used with ANQP or
with other (including vendor specific) advertisement protocols.
gas_request <BSSID> <AdvProtoID> [Query]
gas_response_get <addr> <dialog token> [offset,length]
For example, ANQP query for Capability list in interactive wpa_cli
session:
> gas_request 02:00:00:00:01:00 00 000102000101
<3>GAS-RESPONSE-INFO addr=02:00:00:00:01:00 dialog_token=0
status_code=0 resp_len=32
> gas_response_get 02:00:00:00:01:00 00
01011c00010102010501070108010c01dddd0c00506f9a110200020304050607
> gas_response_get 02:00:00:00:01:00 00 0,10
01011c00010102010501
> gas_response_get 02:00:00:00:01:00 00 10,10
070108010c01dddd0c00
> gas_response_get 02:00:00:00:01:00 00 20,10
506f9a11020002030405
> gas_response_get 02:00:00:00:01:00 00 30,2
0607
It should be noted that the maximum length of the response buffer is
currently 4096 bytes which allows about 2000 bytes of the response data
to be fetched with a single gas_response_get command. If the response is
longer, it can be fetched in pieces as shown in the example above.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
If 4-way handshake fails due to likely PSK failure or if EAP
authentication fails, disable the network block temporarily. Use longer
duration if multiple consecutive failures are seen.
Signed-hostap: Jouni Malinen <j@w1.fi>
If the p2p_find command is used without the delay parameter, a 500 ms
default search delay will now be used when any interface using the same
radio is in an concurrent operation. "p2p_find delay=0" can be used to
enforce the old behavior in such a case if needed.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
A new optional delay=<search delay in milliseconds> parameter can now be
used with p2p_find command to request an extra delay between search
iterations. This can be used, e.g., to make p2p_find friendlier to
concurrent operations by avoiding it from taking 100% of the radio
resources.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
Hotspot 2.0 allows only WPA2-Enterprise to be used, so other types of
networks must not be indicated as Hotspot 2.0 networks even if they
(incorrectly) advertise HS 2.0 support.
Signed-hostap: Jouni Malinen <j@w1.fi>
Add optional "ht40" argument for p2p_group_add command to enable 40 MHz
in 5GHz band. This configures the secondary channel, when HT support is
enabled and if the HW supports 40 MHz channel width.
Signed-hostap: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Allow the user to configure an RSSI threshold in dBm below which the
nl80211 driver won't report scan results. Currently only supported
during scheduled (PNO) scans.
Signed-off-by: Thomas Pedersen <c_tpeder@qca.qualcomm.com>
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
This functionality could be shared for other commands, too, so move
it to a common function. In addition, implement the validation in a
bit more strict way to avoid accepting values like '-123' as a valid
PIN.
Signed-hostap: Jouni Malinen <j@w1.fi>
Reject invalid PIN value in p2p_connect command. Before this, typos
like "pbd" as the third parameter could have resulted in OK return
value since this parameter was interpreted as the PIN.
Signed-hostap: Masashi Honma <masashi.honma@gmail.com>
WPS_ER_NFC_CONFIG_TOKEN command can now be used to build a NFC
configuration token based on AP Settings learnt with WPS_ER_LEARN
or set with WPS_ER_CONFIG.
Signed-hostap: Jouni Malinen <j@w1.fi>
The new wpa_supplicant ctrl_iface command WPS_NFC_TAG_READ can now be
used to process NFC tags read by external programs to initiate
wpa_supplicant to use NFC Configuration Token to create a new network.
Signed-hostap: Jouni Malinen <j@w1.fi>
Instead of requiring low-level access to an NFC device and synchronous
operations, the new WPS_NFC_TOKEN and WPS_NFC ctrl_iface commands can be
used to build a NFC password token and initiate WPS protocol run using
that token (or pre-configured values) as separate commands. The
WPS_NFC_TOKEN output can be written to a NFC tag using an external
program, i.e., wpa_supplicant does not need to have low-level code for
NFC operations for this.
Signed-hostap: Jouni Malinen <j@w1.fi>
Previously, a pending scan request could be left running when processing
DISCONNECT command from control interface. This can result in unexpected
scan, so cancel the request to avoid this.
Signed-hostap: Jouni Malinen <j@w1.fi>
Use wpa_supplicant_set_state() to initialize state to DISCONNECT so that
autoscan gets initialized properly. This needs a change in
autoscan_init() to avoid extra scan request that would postpone the
first scan request when an interface is added.
Signed-hostap: Jouni Malinen <j@w1.fi>
Add an additional parameter to prioritize either sta or p2p connection
to resolve conflicts arising during single channel concurrency.
Signed-hostap: Jithu Jance <jithu@broadcom.com>
This is a workaround for interoperability issues with some deployed P2P
implementations that require a Provision Discovery exchange to be used
before GO Negotiation. The new provdisc parameter for the p2p_connect
command can be used to request this behavior without having to run a
separate p2p_prov_disc command.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
The nl80211 driver interface does not allow 128-bit WEP to be used
without a vendor specific cipher suite and no such suite is defined for
this purpose. Do not accept WEP key length 16 for nl80211 driver
interface forn ow. wext-interface can still try to use these for
backwards compatibility.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
If the AP indicates support for Hotspot 2.0, show this in the
ctrl_iface commands for BSS table and status.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
Do not try to associate with a network that has an invalid or incomplete
configuration because the association or at least data connection would
fail anyway. This commits adds a common function for checking whether a
network block is disabled to make it easier to check network blocks
without having to reject them during configuration file parsing (which
would prevent wpa_supplicant from starting). The only additional check
added in this commit is to verify the WEP key length. Similar checks for
other parameters can be added in future commits.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
Commit 7de5688d68 started using
wpa_supplicant_ctrl_iface_ctrl_rsp_handle() from the D-Bus code, but
left this function in ctrl_iface.c that is included conditionally. Fix
this by moving the common function into wpa_supplicant.c so that it can
be included for builds that include only either ctrl_iface or D-Bus.
Signed-hostap: Jouni Malinen <j@w1.fi>
intended-for: hostap-1
An existing persistent group information can now be used to force GO
Negotiation to use the previously used SSID/passphrase from a persistent
group if we become a GO. This can be used as an alternative to inviting
a new P2P peer to join the group (i.e., use GO Negotiation with GO
intent 15 instead of starting an autonomous GO and using invitation),
e.g., in case a GO Negotiation Request is received from a peer while we
are not running as a GO. The persistent group to use for parameters is
indicated with persistent=<network id> parameter to p2p_connect.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
wpa_supplicant can now be requested to automatically figure out whether
the indicated peer is operating as a GO and if so, use join-a-group
style PD instead of pre-GO Negotiation PD.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
p2p_connect command can now be used with an optional "auto" parameter
to request wpa_supplicant to determine automatically whether to use
join-a-group operation (if the peer is operating as a GO) or group
formation. This makes it easier for external programs to handle
connection type selection by offloading this to wpa_supplicant. The
previously used p2p_connect join commands can be replaced with
p2p_connect auto to use this new mechanism.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
This optional parameter to the BSS command can be used to select which
fields are included in the output to avoid having to parse through
unneeded information and to reduce the buffer size.
Signed-off-by: Dmitry Shmidt <dimitrysh@google.com>
Enable control of wpa_s->scan_interval via D-Bus. This parameter
controls the delay between successive scans for a suitable AP.
Also, update dbus.doxygen with ScanInterval, and some other
parameters that were undocumented.
Signed-hostap: Mukesh Agrawal <quiche@chromium.org>
There is no need to use reassociation instead of association in a case
the previous connection was explicitly disconnected.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
This allows the ctrl_iface SCAN command to be used to run through a scan
to collect full scan results when sched_scan is in progress. sched_scan
will be re-started automatically after the full scan.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
