Commit graph

480 commits

Author SHA1 Message Date
Jouni Malinen
61a56c1480 Add group_mgmt network parameter for PMF cipher selection
The new wpa_supplicant network parameter group_mgmt can be used to
specify which group management ciphers (AES-128-CMAC, BIP-GMAC-128,
BIP-GMAC-256, BIP-CMAC-256) are allowed for the network. If not
specified, the current behavior is maintained (i.e., follow what the AP
advertises). The parameter can list multiple space separate ciphers.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2017-09-26 17:40:02 +03:00
Avraham Stern
b3c148e9f8 RRM: Send reject/refuse response only to unicast measurement request
IEEE Std 802.11-2016, 11.11.6 specifies that a station that is unable to
make a requested measurement or refuses to make a measurement shall
respond only if the measurement request was received within an
individually addressed radio measurement request frame, but shall not
respond if such a request was received in a group addressed frame.

Signed-off-by: Avraham Stern <avraham.stern@intel.com>
2017-07-17 17:43:32 +03:00
Andrei Otcheretianski
bfbc41eace DPP: Fix compilation without openssl
dpp.h file requires openssl in order to compile, which breaks
compilation on systems without it.
Move DPP_OUI_TYPE to ieee802_11_defs.h and don't include dpp.h when
not really needed.

Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
2017-07-07 23:37:45 +03:00
Jouni Malinen
da143f7fb9 FILS: Fix EVENT_ASSOC processing checks for driver-SME
Commit 5538fc9309 ('FILS: Track completion
with FILS shared key authentication offload') added an additional case
for calling wpa_supplicant_event_assoc_auth() from EVENT_ASSOC handling
in case of FILS-completion with driver-based-SME. However, that checked
what placed outside the data != NULL case while data != NULL needs to
apply for this case as well due to wpa_supplicant_event_assoc_auth()
behavior. Move the data != NULL check to apply to both cases to avoid
potentially issues if a driver interface were to return EVENT_ASSOC
without the associate data. (CID 164708)

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2017-06-19 23:36:13 +03:00
Jouni Malinen
a0d5c56f8b DPP: Network Introduction protocol for wpa_supplicant
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2017-06-19 21:13:59 +03:00
Jouni Malinen
567da5bbd0 DPP: Add new AKM
This new AKM is used with DPP when using the signed Connector to derive
a PMK. Since the KCK, KEK, and MIC lengths are variable within a single
AKM, this needs number of additional changes to get the PMK length
delivered to places that need to figure out the lengths of the PTK
components.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2017-06-19 21:13:17 +03:00
Jouni Malinen
461d39af40 DPP: Configuration exchange
This adds support for DPP Configuration Protocol using GAS. Full
generation and processing of the configuration object is not included in
this commit.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2017-06-19 21:13:15 +03:00
Jouni Malinen
30d27b048e DPP: Authentication exchange
Add wpa_supplicant control interface commands for managing DPP
Authentication exchange.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2017-06-19 21:12:30 +03:00
Vasanthakumar Thiagarajan
aa56e36d66 driver: Make DFS domain information available to core
Current DFS domain information of the driver can be used in ap/dfs
to comply with DFS domain specific requirements like uniform spreading
for ETSI domain.

Signed-off-by: Vasanthakumar Thiagarajan <vthiagar@qti.qualcomm.com>
2017-05-13 20:01:44 +03:00
Vidyullatha Kanchanapally
bbe7969d63 FILS: Update cache identifier on association
This is needed when offloading FILS shared key to the drivers.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2017-04-07 18:59:12 +03:00
Vidyullatha Kanchanapally
f705f41b7f FILS: Update PMKSA cache with FILS shared key offload
Add a new PMKSA cache entry within wpa_supplicant if a driver event from
offloaded FILS shared key authentication indicates a new PMKSA entry was
created.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2017-04-07 18:46:13 +03:00
Vidyullatha Kanchanapally
01ef320f19 FILS: Update ERP next sequence number with driver offload
This keeps the internal ERP information within wpa_supplicant in sync
with the driver when offloading FILS shared key authentication.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2017-04-07 18:46:13 +03:00
Vidyullatha Kanchanapally
5538fc9309 FILS: Track completion with FILS shared key authentication offload
Update the internal fils_completed state when offloading FILS shared key
authentication to the driver.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2017-04-07 18:46:13 +03:00
Shaul Triebitz
3d5f0e916d wpa_supplicant: Avoid associating to temp disabled SSID in ap_scan=2
In ap_scan=2 mode, wpa_supplicant_assoc_try() did not check whether the
SSID is temporarily disabled before trying to associate and this may
result in an infinite connect/disconnect loop. If the association
succeeds while the SSID is temporarily disabled, wpa_supplicant will
request to deauthenticate and that in turn will cause the SSID to be
temporarily disabled again. Fix that by postponing the association until
the SSID is no longer temporarily disabled.

Signed-off-by: Shaul Triebitz <shaul.triebitz@intel.com>
2017-03-29 15:03:16 +03:00
Jouni Malinen
76e20f4fa7 FILS: Add FILS SK auth PFS support in STA mode
This adds an option to configure wpa_supplicant to use the perfect
forward secrecy option in FILS shared key authentication. A new build
option CONFIG_FILS_SK_PFS=y can be used to include this functionality. A
new runtime network profile parameter fils_dh_group is used to enable
this by specifying which DH group to use. For example, fils_dh_group=19
would use FILS SK PFS with a 256-bit random ECP group.

Signed-off-by: Jouni Malinen <j@w1.fi>
2017-03-12 23:20:32 +02:00
Jouni Malinen
0a6147991e OWE: Process Diffie-Hellman Parameter element in STA mode
This adds STA side addition of OWE Diffie-Hellman Parameter element into
(Re)Association Request frame and processing it in (Re)Association
Response frame.

Signed-off-by: Jouni Malinen <j@w1.fi>
2017-03-12 19:24:11 +02:00
Jouni Malinen
a1ea1b4522 OWE: Define and parse OWE AKM selector
This adds a new RSN AKM "OWE".

Signed-off-by: Jouni Malinen <j@w1.fi>
2017-03-12 19:24:11 +02:00
Johannes Berg
15e5ee0b75 wpa_supplicant: events: Don't bounce timeout reason through a buffer
There's no point in making the code use a stack buffer and first copying
the string there, only to copy it again to the output. Make the output
directly use the reason string.

Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2017-03-11 10:52:43 +02:00
Jouni Malinen
869af30728 FILS: Use FILS Cache Identifier to extend PMKSA applicability
This allows PMKSA cache entries for FILS-enabled BSSs to be shared
within an ESS when the BSSs advertise the same FILS Cache Identifier
value.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2017-02-26 12:05:40 +02:00
Purushottam Kushwaha
3f23260da8 nl80211: Notify reason for connection timeout failure
This adds reason for timeout in event CTRL-EVENT-ASSOC-REJECT whenever
connection failure happens because of timeout. This extends the
"timeout" parameter in the event to include the reason, if available:
timeout=scan, timeout=auth, timeout=assoc.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2017-02-20 10:47:08 +02:00
Jouni Malinen
bcf66493cf Fix estimated throughput based skip-roam case
Commit 8d1e693186 ('Use estimated
throughput to avoid signal based roaming decision') added a check for
the current BSS estimated throughput being significantly higher than the
selected BSS estimated throughput. However, this case for skipping a
roam used "return 1" which actually allows the roam. Fix this by
returning 0 in this case.

Signed-off-by: Jouni Malinen <j@w1.fi>
2017-02-05 21:52:26 +02:00
Andrejs Cainikovs
6a5425fd60 Increase delayed EAPOL RX frame timeout
Increase the EAPOL RX frame timeout from 100 to 200 ms. This fixes lack
of optimization (i.e., first EAPOL frame dropped) in occasional roaming
and authentication cases on EAP networks if the kernel events can be
reordered and delayed a bit longer.

Signed-off-by: Tomoharu Hatano <tomoharu.hatano@sonymobile.com>
2017-01-29 18:41:29 +02:00
Jouni Malinen
34e8bfd7a9 Skip EVENT_ACS_CHANNEL_SELECTED also without CONFIG_AP
CONFIG_ACS alone should not refer to wpa_s->ap_iface to avoid potential
compilation issues.

Signed-off-by: Jouni Malinen <j@w1.fi>
2017-01-28 11:57:23 +02:00
Jouni Malinen
0f9b4a0f1d bgscan: Deliver beacon loss event to bgscan modules
This adds a call to the notify_beacon_loss() callback functions when
beacon loss is detected. In addition, a new CTRL-EVENT-BEACON-LOSS event
is made available through the wpa_supplicant control interface.

Signed-off-by: Jouni Malinen <j@w1.fi>
2017-01-08 12:17:58 +02:00
Avraham Stern
76196ddb2b wpa_supplicant: Add support for Beacon Report Radio Measurement
Beacon Report Radio Measurement is defined in IEEE Std 802.11-2016,
11.11.9.1. Beacon Report is implemented by triggering a scan on the
requested channels with the requested parameters.

Signed-off-by: Avraham Stern <avraham.stern@intel.com>
2017-01-03 15:18:30 +02:00
Jouni Malinen
6e374bd44d Ignore scan results from ongoing scan when FLUSH command is issued
This makes wpa_supplicant behavior more consistent with FLUSH command to
clear all state. Previously, it was possible for an ongoing scan to be
aborted when the FLUSH command is issued and the scan results from that
aborted scan would still be processed and that would update the BSS
table which was supposed to cleared by the FLUSH command.

This could result in hwsim test case failures due to unexpected BSS
table entries being present after the FLUSH command.

Signed-off-by: Jouni Malinen <j@w1.fi>
2016-12-11 12:45:08 +02:00
Jouni Malinen
e65a87b399 Debug print scan results matching the currently selected network
This provides more details on BSS selection process in the debug log.
Previously, the BSSs that were not either the current or the selected
one were not necessarily printed at all. Now all BSSs that match the
currently selected network are listed with their frequency and signal
strength details.

Signed-off-by: Jouni Malinen <j@w1.fi>
2016-11-13 18:22:38 +02:00
Jouni Malinen
8d1e693186 Use estimated throughput to avoid signal based roaming decision
Previously, the estimated throughput was used to enable roaming to a
better AP. However, this information was not used when considering a
roam to an AP that has better signal strength, but smaller estimated
throughput. This could result in allowing roaming from 5 GHz band to 2.4
GHz band in cases where 2.4 GHz band has significantly higher signal
strength, but still a lower throughput estimate.

Make this less likely to happen by increasing/reducing the minimum
required signal strength difference based on the estimated throughputs
of the current and selected AP. In addition, add more details about the
selection process to the debug log to make it easier to determine whaty
happened and why.

Signed-off-by: Jouni Malinen <j@w1.fi>
2016-11-13 17:52:32 +02:00
Jouni Malinen
81a10a9442 Do not try to start/join RSN IBSS without CONFIG_IBSS_RSN=y
Previously, a build without IBSS RSN support tried to start/join an IBSS
even if the profile was configured with RSN parameters. This does not
work and resulted in quite confusing debug log. Make this clearer by
explicitly checking for this case and reject the connection attempt with
a clearer debug log entry instead of trying something that is known to
fail.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2016-10-28 19:33:20 +03:00
Jouni Malinen
706df4291b FILS: Association Response processing (STA)
Decrypt the AES-SIV protected elements and verify Key-Auth. Parse and
configure keys to the driver.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2016-10-26 00:20:04 +03:00
Avraham Stern
e3e2fe3a42 Always propagate scan results to all interfaces
Scan results were not propagated to all interfaces if scan results
started a new operation, in order to prevent concurrent operations. But
this can cause other interfaces to trigger a new scan when scan results
are already available. Instead, always notify other interfaces of the
scan results, but note that new operations are not allowed.

Signed-off-by: Avraham Stern <avraham.stern@intel.com>
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
2016-10-15 19:13:30 +03:00
Avraham Stern
14f34a7303 Continue scanning if sched_scan stops unexpectedly
When scheduled scan stops without the interface request (for example,
driver stopped it unexpectedly), start a regular scan to continue
scanning for networks and avoid being left with no scan at all.

Signed-off-by: Avraham Stern <avraham.stern@intel.com>
2016-10-02 19:38:57 +03:00
David Spinadel
1ac388633a Remove disconnected APs from BSS table if likely out-of-range
In some cases, after a sudden AP disappearing and reconnection to
another AP in the same ESS, if another scan occurs, wpa_supplicant might
try to roam to the old AP (if it was better ranked than the new one)
because it is still saved in BSS list and the blacklist entry was
cleared in previous reconnect. This attempt is going to fail if the AP
is not present anymore and it'll cause long disconnections.

Remove an AP that is probably out of range from the BSS list to avoid
such disconnections. In particular mac80211-based drivers use the
WLAN_REASON_DISASSOC_DUE_TO_INACTIVITY reason code in locally generated
disconnection events for cases where the AP does not reply anymore.

Signed-off-by: David Spinadel <david.spinadel@intel.com>
2016-10-01 11:14:02 +03:00
Arik Nemtsov
ebf59eb549 Restart PNO/sched_scan on channel list update
As the scan channels might need to change when the channel list has been
updated by the kernel. Use the simulated sched_scan timeout
(wpas_scan_restart_sched_scan()) to handle a possible race where an
ongoing sched_scan has stopped asynchronously while trying to restart a
new sched_scan.

Signed-off-by: Arik Nemtsov <arikx.nemtsov@intel.com>
2016-09-30 22:45:03 +03:00
vamsi krishna
6ad37d73ca MBO: Add support to ignore association disallowed set by AP
Add a testing mechanism to allow association disallowed set by AP to be
ignored. This can be used to verify AP behavior for disallowing a
specific association.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2016-09-25 17:31:26 +03:00
Mikael Kanstrup
02adead53e Add ignore_auth_resp control interface debug parameter
Implement "SET ignore_auth_resp <0/1>" command to simulate auth/assoc
response loss and EAPOL RX packet loss by ignoring corresponding
incoming events.

Signed-off-by: Mikael Kanstrup <mikael.kanstrup@sonymobile.com>
2016-09-23 17:36:55 +03:00
Moshe Benji
14220fe64c Flush the BSS (scan) entries when an interface becomes disabled
When an interface becomes disabled (e.g., when RF-kill becomes blocked)
we should clear the stored scan results to avoid maintaining stale
information.

Fix this by flushing the BSS entries when an interface becomes
disabled.

Signed-off-by: Moshe Benji <moshe.benji@intel.com>
2016-09-22 23:31:19 +03:00
Jouni Malinen
6c33ca9f95 Add group_rekey parameter for IBSS
The new network profile parameter group_rekey can now be used to specify
the group rekeying internal in seconds for IBSS.

Signed-off-by: Jouni Malinen <j@w1.fi>
2016-08-13 16:29:01 +03:00
Jouni Malinen
e07adb7faa Fix EAP state machine reset with offloaded roaming and authorization
If the driver indicates a roamed event with already completed
authorization, altAccept = TRUE could have resulted in the EAP state
machine ending up in the FAILURE state from the INITIALIZE state. This
is not correct behavior and similar cases were already addressed for FT
and WPA-PSK. Fix the offloaded roamed+authorized (EAP/PMKSA caching)
case by doing similar changes to EAPOL/EAP state variable updates during
association event handling.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2016-08-11 16:05:45 +03:00
Masashi Honma
fac72f93dd mesh: Stop joining to different frequency network
Signed-off-by: Masashi Honma <masashi.honma@gmail.com>
2016-07-23 21:57:15 +03:00
Masashi Honma
7035162311 mesh: Join an existing MBSS instead of creating a new one
If scan results show a matching existing MBSS, join it instead of
creating a new MBSS.

Signed-off-by: Masashi Honma <masashi.honma@gmail.com>
2016-07-23 21:57:11 +03:00
Peng Xu
a6f5b1937a P2P: Allow P2P listen being offloaded to the driver/firmware
This allows P2P Listen to be offloaded to device to enhance power
saving.

To start P2P listen offload, from wpa_cli interface, issue the command:
	p2p_lo_start <freq> <period> <interval> <count>

To stop P2P listen offload, issue the command:
	p2p_lo_stop

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2016-07-03 22:36:58 +03:00
Jouni Malinen
37fd0be2d3 Add CTRL-EVENT-CHANNEL-SWITCH event to indicate channel changes
This provides information of the channel switch to wpa_supplicant
control interface monitors.

Signed-off-by: Jouni Malinen <j@w1.fi>
2016-06-27 21:10:35 +03:00
Jouni Malinen
9a5160f5fb Report connection timeouts in CTRL-EVENT-ASSOC-REJECT
Add a new "timeout" argument to the event message if the nl80211 message
indicates that the connection failure is not due to an explicit AP
rejection message. This makes it easier for external programs to figure
out why the connection failed.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2016-05-31 00:11:42 +03:00
Lior David
a26c9c2e71 Fix sending non-Public Action frames over P2P Device interface
The P2P Device interface can only send Public Action frames. Non-Public
Action frames must be sent over a group interface. The previous
implementation sometimes tried to send non-Public Action frames such as
GO Discoverability over the P2P Device interface, however, the source
address of the frame was set to the group interface address so the code
in offchannel.c knew to select the correct interface for the TX.

The check breaks when the P2P Device and group interfaces have the same
MAC address. In this case the frame will be sent over the P2P Device
interface and the send will fail.

Fix this problem in two places:
1. In offchannel, route non-Public Action frames to the GO
   interface when the above conditions are met.
2. When a TX_STATUS event arrives on such routed frame, it will
   arrive on the GO interface but it must be handled by the P2P Device
   interface since it has the relevant state logic.

Signed-off-by: Lior David <qca_liord@qca.qualcomm.com>
2016-05-21 00:17:45 +03:00
Ilan Peer
3b11ad34eb Send CTRL-EVENT-REGDOM-CHANGE event on the parent interface
The NL80211_CMD_WIPHY_REG_CHANGE can be handled by any of the
interfaces that are currently controlled by the wpa_supplicant.
However, some applications expect the REGDOM_CHANGE event to be
sent on the control interface of the initially added interface
(and do not expect the event on any of child interfaces).

To resolve this, when processing NL80211_CMD_WIPHY_REG_CHANGE,
find the highest parent in the chain, and use its control interface
to emit the CTRL-EVENT-REGDOM-CHANGE event.

Signed-off-by: Ilan Peer <ilan.peer@intel.com>
2016-05-14 17:19:02 +03:00
Sunil Dutt
03626e9157 Skip connection attempt for non-RSN networks if PMF is set to required
Since ieee80211w=2 is an explicit configuration to wpa_supplicant, the
connection attempt for such non-PMF (non-RSN) capable networks should be
skipped.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2016-05-05 21:09:08 +03:00
David Spinadel
4a742011ab wpa_supplicant: Handle LCI request
Handle radio measurement request that contains LCI request. Send
measurement report based on a configurable LCI report element. The LCI
report element is configured over the control interface with

SET lci <hexdump of the element>

and cleared with

SET lci ""

Signed-off-by: David Spinadel <david.spinadel@intel.com>
2016-04-17 12:29:12 +03:00
Matti Gottlieb
ece4ac5f4e HS 2.0: Add support for configuring frame filters
When a station starts an association to a Hotspot 2.0 network, request
the driver to do the following, based on the BSS capabilities:

1. Enable gratuitous ARP filtering
2. Enable unsolicited Neighbor Advertisement filtering
3. Enable unicast IP packet encrypted with GTK filtering if
   DGAF disabled bit is zero

Clear the filter configuration when the station interface is
disassociated.

Signed-off-by: Matti Gottlieb <matti.gottlieb@intel.com>
2016-04-08 15:21:18 +03:00
Lior David
90f14962ec wpa_supplicant: "don't care" value for pbss in ssid structure
Add a new value 2 to the pbss parameter of wpa_ssid structure, which
means "don't care". This value is used in infrastructure mode to request
connection to either AP or PCP, whichever is available in the scan
results. The value is also used in regular WPS (not P2P group formation)
to make WPS work with devices running as either AP or PCP.

Signed-off-by: Lior David <qca_liord@qca.qualcomm.com>
2016-04-08 12:56:34 +03:00