This is an initial step in allowing non-operating channel operations
with DPP when hostapd is the Responder. For now, this is only used for
specifying role=configurator/enrollee and qr=mutual cases similarly to
the wpa_supplicant configuration for in Responder role. Request to use a
non-operating channel will be rejected.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Add limit on number of failed attempts that could have used PKEX code.
If the limit (5) is reached, drop the PKEX state (including the code)
and report this on the control interface to indicate that a new code
needs to be entered due to possible attack.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Clean up the pending PKEX exchange if Commit-Reveal Request processing
indicates a mismatch in the PKEX code. Previously, the this case was
silently ignored and the session was left in pending state that
prevented new PKEX exchanges from getting initated. Now, a new attempt
is allowed to be initiated.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Report mismatching finite cyclic group with PKEX Exchange Response using
STATUS_BAD_GROUP and provide more detailed error report over the control
interface on the peer device when this happens.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
The previously used WLAN_REASON_MICHAEL_MIC_FAILURE (14) value as a
response to Authentication frame or (Re)Association Request frame is not
correct since the resp value is encoded in the Status Code (not Reason
Code) field. Status Code 14 is WLAN_STATUS_UNKNOWN_AUTH_TRANSACTION
which is really what this value would have meant in the response frames.
There is no Michael MIC failure status code, so have to use the generic
"Unspecified failure" (1) reason code for these cases.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Indicate to upper layers if PKEX Commit-Reveal Request frame AES-SIV
decryption fails. That is a likely sign of the PKEX code mismatch
between the devices.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Build breakage was introduced by commit
d8afdb210e ('Allow EAPOL-Key messages 1/4
and 3/4 to be retransmitted for testing') for some
CONFIG_TESTING_OPTIONS=y builds without CONFIG_IEEE80211W=y.
Signed-off-by: Lior David <qca_liord@qca.qualcomm.com>
This provides access to the Minimum/Maximum Transmit Power Capabilitie
fileds (the nominal minimum/maximum transmit power with which the STA
is capable of transmitting in the current channel; signed integer in
units of decibels relative to 1 mW).
Signed-off-by: bhagavathi perumal s <bperumal@qti.qualcomm.com>
Handle OWE DH exchange and key setup when processing the association
event from a driver that implements AP SME.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
While most places using this should be for cases where the hw_features
functionality is required, there seem to be some paths that are getting
exposed in new OWE related operations where that might not be the case.
Add explicit NULL pointer checks to avoid dereferencing the pointer if
it is not set when operating with driver wrappers that do not provide
sufficient information.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Normally, WNM-Sleep Mode exit with management frame protection
negotiated would result in the current GTK/IGTK getting added into the
WNM-Sleep Mode Response frame. Some station implementations may have a
vulnerability that results in GTK/IGTK reinstallation based on this
frame being replayed. Add a new hostapd configuration parameter that can
be used to disable that behavior and use EAPOL-Key frames for GTK/IGTK
update instead. This would likely be only used with
wpa_disable_eapol_key_retries=1 that enables a workaround for similar
issues with EAPOL-Key. This is related to station side vulnerabilities
CVE-2017-13087 and CVE-2017-13088. To enable this AP-side workaround,
set wnm_sleep_mode_no_keys=1.
Signed-off-by: Jouni Malinen <j@w1.fi>
When strict group rekeying is in effect, every station that leaves will
cause a rekeying to happen 0.5 s after leaving. However, if a lot of
stations join/leave, the previous code could postpone this rekeying
forever, since it always re-registers the handling with a 0.5 s timeout.
Use eloop_deplete_timeout() to address that, only registering the
timeout from scratch if it wasn't pending.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
In order to test the WoWLAN GTK rekeying KRACK mitigation, add a
REKEY_GTK hostapd control interface command that can be used at certain
points of the test.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Allow the Initiator to request a different channel to be used for DPP
Authentication and DPP Configuration exchanges. This commit adds support
for this in wpa_supplicant with the optional neg_freq=<freq in MHz>
parameter in DPP_AUTH_INIT.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This is useful for protocol testing purposes and UI needs to display
more detailed information about DPP exchanges.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This is helpful for testing purposes and also for upper layer components
that may want to show more detailed progress through a DPP exchange.
Both the DPP-TX and DPP-TX-STATUS events are provided.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This is helpful for testing purposes and also for upper layer components
that may want to show more detailed progress through a DPP exchange.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Now that dpp_check_attrs() takes care of verifying that no attributes
are after the Wrapped Data attribute, the duplicated checks in hostapd
and wpa_supplicant side of the implementation can be removed.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Build breakage was introduced by commit
16579769ff ('Add testing functionality for
resetting PN/IPN for configured keys') for some CONFIG_TESTING_OPTIONS=y
builds.
Signed-off-by: Ben Greear <greearb@candelatech.com>
The hostapd bss_transition parameter was previously used to control
advertisement of BSS Transition Management support, but it was not used
when processing BSS Transition Management Query/Response frames. Add an
explicit check during frame processing as well so that any misbehaving
station is ignored. In addition to bss_transition=1, allow mbo=1 to be
used to mark the functionality enabled.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
The hostapd wnm_sleep_mode parameter was previously used to control
advertisement of WNM-Sleep Mode support, but it was not used when
processing a request to use WNM-Sleep Mode. Add an explicit check during
request processing as well so that any misbehaving station is ignored.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This allows hostapd testing functionality to be forced to send out a
plaintext EAPOL-Key frame with the RESEND_* command. That can be useful
in seeing how the station behaves if an unencrypted EAPOL frame is
received when TK is already configured.
This is not really perfect since there is no convenient way of sending
out a single unencrypted frame in the current nl80211 design. The
monitor interface could likely still do this, but that's not really
supposed to be used anymore. For now, clear and restore TK during this
operation. The restore part is not really working correctly, though,
since it ends up clearing the TSC value on the AP side and that shows up
as replay protection issues on the station. Anyway, this is sufficient
to generate sniffer captures to analyze station behavior.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This adds a new hostapd configuration parameter
wpa_disable_eapol_key_retries=1 that can be used to disable
retransmission of EAPOL-Key frames that are used to install
keys (EAPOL-Key message 3/4 and group message 1/2). This is
similar to setting wpa_group_update_count=1 and
wpa_pairwise_update_count=1, but with no impact to message 1/4
retries and with extended timeout for messages 4/4 and group
message 2/2 to avoid causing issues with stations that may use
aggressive power saving have very long time in replying to the
EAPOL-Key messages.
This option can be used to work around key reinstallation attacks
on the station (supplicant) side in cases those station devices
cannot be updated for some reason. By removing the
retransmissions the attacker cannot cause key reinstallation with
a delayed frame transmission. This is related to the station side
vulnerabilities CVE-2017-13077, CVE-2017-13078, CVE-2017-13079,
CVE-2017-13080, and CVE-2017-13081.
This workaround might cause interoperability issues and reduced
robustness of key negotiation especially in environments with
heavy traffic load due to the number of attempts to perform the
key exchange is reduced significantly. As such, this workaround
is disabled by default (unless overridden in build
configuration). To enable this, set the parameter to 1.
It is also possible to enable this in the build by default by
adding the following to the build configuration:
CFLAGS += -DDEFAULT_WPA_DISABLE_EAPOL_KEY_RETRIES=1
Signed-off-by: Jouni Malinen <j@w1.fi>
The new hostapd control interface commands "RESEND_M1 <addr>" and
"RESEND_M3 <addr>" can be used to request a retransmission of the 4-Way
Handshake messages 1/4 and 3/4 witht he same or modified ANonce (in M1).
This functionality is for testing purposes and included only in builds
with CONFIG_TESTING_OPTIONS=y.
Signed-off-by: Jouni Malinen <j@w1.fi>
The new hostapd control interface command "RESEND_GROUP_M1 <addr>" can
be used to request a retransmission of the Group Key Handshake message
1/2 for the current GTK.
This functionality is for testing purposes and included only in builds
with CONFIG_TESTING_OPTIONS=y.
Signed-off-by: Jouni Malinen <j@w1.fi>
This can be used to test replay protection. The "RESET_PN" command in
wpa_supplicant and "RESET_PN <addr>" command in hostapd resets the local
counters to zero for the last configured key. For hostapd, the address
parameter specifies which STA this operation is for or selects GTK
("ff:ff:ff:ff:ff:ff") or IGTK ("ff:ff:ff:ff:ff:ff IGTK").
This functionality is for testing purposes and included only in builds
with CONFIG_TESTING_OPTIONS=y.
Signed-off-by: Jouni Malinen <j@w1.fi>
This was originally added to allow the IEEE 802.11 protocol to be
tested, but there are no known fully functional implementations based on
this nor any known deployments of PeerKey functionality. Furthermore,
PeerKey design in the IEEE Std 802.11-2016 standard has already been
marked as obsolete for DLS and it is being considered for complete
removal in REVmd.
This implementation did not really work, so it could not have been used
in practice. For example, key configuration was using incorrect
algorithm values (WPA_CIPHER_* instead of WPA_ALG_*) which resulted in
mapping to an invalid WPA_ALG_* value for the actual driver operation.
As such, the derived key could not have been successfully set for the
link.
Since there are bugs in this implementation and there does not seem to
be any future for the PeerKey design with DLS (TDLS being the future for
DLS), the best approach is to simply delete all this code to simplify
the EAPOL-Key handling design and to get rid of any potential issues if
these code paths were accidentially reachable.
Signed-off-by: Jouni Malinen <j@w1.fi>
The previous implementation ended up starting a new EAPOL-Key 4-way
handshake if the STA were to attempt to perform another association.
This resulted in immediate disconnection since the PTK was not ready for
configuring FILS TK at the point when EAPOL-Key msg 1/4 is sent out.
This is better than alloing the association to continue with the same TK
reconfigured, but not really ideal.
Address this potential sequence by not starting a new 4-way handshake on
the additional association attempt. Instead, allow the association to
complete, but do so without reconfiguring the TK to avoid potential
issues with PN reuse with the same TK.
Signed-off-by: Jouni Malinen <j@w1.fi>
This allows ext_mgmt_frame_handling=1 cases with hostapd to process TX
status events based on external processing. This is useful for increased
test coverage of management frame processing.
Signed-off-by: Jouni Malinen <j@w1.fi>
The Authenticator state machine path for PTK rekeying ended up bypassing
the AUTHENTICATION2 state where a new ANonce is generated when going
directly to the PTKSTART state since there is no need to try to
determine the PMK again in such a case. This is far from ideal since the
new PTK would depend on a new nonce only from the supplicant.
Fix this by generating a new ANonce when moving to the PTKSTART state
for the purpose of starting new 4-way handshake to rekey PTK.
Signed-off-by: Jouni Malinen <j@w1.fi>
Do not reinstall TK to the driver during Reassociation Response frame
processing if the first attempt of setting the TK succeeded. This avoids
issues related to clearing the TX/RX PN that could result in reusing
same PN values for transmitted frames (e.g., due to CCM nonce reuse and
also hitting replay protection on the receiver) and accepting replayed
frames on RX side.
This issue was introduced by the commit
0e84c25434 ('FT: Fix PTK configuration in
authenticator') which allowed wpa_ft_install_ptk() to be called multiple
times with the same PTK. While the second configuration attempt is
needed with some drivers, it must be done only if the first attempt
failed.
Signed-off-by: Mathy Vanhoef <Mathy.Vanhoef@cs.kuleuven.be>
The new sae_password hostapd configuration parameter can now be used to
set the SAE password instead of the previously used wpa_passphrase
parameter. This allows shorter than 8 characters and longer than 63
characters long passwords to be used. In addition, this makes it
possible to configure a BSS with both WPA-PSK and SAE enabled to use
different passphrase/password based on which AKM is selected.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
The new hostapd configuration parameter owe_groups can be used to
specify a subset of the allowed DH groups as a space separated list of
group identifiers.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This additional field was added to DPP Public Action frames in DPP tech
spec v0.2.3 to support cryptographic agility in the future.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
The owe_transition_bssid and owe_transition_ssid parameters can now be
replace with owe_transition_ifname to clone the BSSID/SSID information
automatically in case the same hostapd process manages both the OWE and
open BSS for transition mode.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This extends OWE support in hostapd to allow DH groups 20 and 21 to be
used in addition to the mandatory group 19 (NIST P-256).
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
