This extends hostapd global control interface command "ADD" to use a
configuration file instead of requiring configuration to be built using
SET command.
The command format is now following:
ADD <ifname> <control path|config=<path to config>>
For example:
ADD wlan0 /var/run/hostapd
ADD wlan0 config=/tmp/hostapd.conf
When using the configuration file option, ctrl_interface parameter in
the file needs to be set to allow ENABLE command to be issued on the new
interface.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
There was a comment about the the cleanup steps being from
hostapd_cleanup_iface(). However, the operations that cleared some
security parameters do not seem to exist elsewhere and do not make sense
here. Remove them to avoid changing configuration with DISABLE followed
by ENABLE.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
This fixes some issues where dynamic interface enable/disable cycles
could end up trying to free resources twice and crash the process while
doing so.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
This can be useful in figuring out how drv->last_mgmt_freq gets set
to debug issues with P2P frames being sent on incorrect channel.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
This avoids some issues with the global control interface socket
getting stuck with send buffer limit reached if test cases did not
use wait_global_event().
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
If wpa_supplicant ctrl_iface clients are misbehaving and refusing to
read replies or event messages from wpa_supplicant, the single socket
used in wpa_supplicant to send messages can reach the maximum send
buffer limit. When that happens, no more responses to any client can be
sent. Work around this by closed and reopening the socket in case such a
failure state is detected. This is obviously not desirable since it
breaks existing connected sockets, but is needed to avoid leaving
wpa_supplicant completely unable to respond to any client. Cleaner fix
for this may require more considerable changes in the ctrl_iface design
to move to connection oriented design to allow each client to be handled
separately and unreachability to be detected more reliably.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
This allows Hotspot 2.0 and Interworking strings that use language:name
string (e.g., venue_name) to be encoded using printf format to enter
special characters like newline.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
printf_decode() fills in a binary buffer and returns the length of
the written data. This did not use null termination since initial
use cases used the output as a binary value. However, Hotspot 2.0
cred block values are also using this for parsing strings. Those
cases could end up without proper null termination depending on what
os_malloc() ends up getting as the memory buffer. Fix these and make
printf_decode() more convenient by forcing the output buffer to be
null terminated.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
The language string length needs to be validated to hit into the
three-octet lang field in struct hostapd_lang_string before copying
this. Invalid configuration entries in hostapd.conf could have resulted
in buffer overflow.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
Prepare reply buffer first for all cases and then use a single sendto()
call instead of three calls depending on reply type. This allows simpler
error handling for control interface send operations.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
When no other user preference is specified, opt to use an operating
channel that allows 5 GHz band to be used rather than 2.4 GHz.
Previously, this was already done in practice for HT40 channels since no
such channel is enabled for P2P on 2.4 GHz. This commit extends this to
apply 5 GHz preference for 20 MHz channels as well.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
H3C WA2620i-AGN AP may send an EAP packet with an undefined EAP code
10 after successful EAP authentication which restarts the EAPOL
state machine. Drop such frames with this unrecognized code without
advancing the EAPOL supplicant or EAP peer state machines to avoid
interoperability issues with the AP.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
The interval for the PNO scan did not use the configured sched_scan
interval. This commit addresses the same by using the configured value
or the default of 10 seconds if configuration parameter is not used.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
There is no point in updating the RNonce for every obtained TPK M1 frame
(e.g., retransmission due to timeout) with the same INonce (SNonce in
FTIE). Update RNonce only if a TPK M1 is received with a different
INonce (new TDLS session) to avoid issues with two setup exchanges
getting mixed and exchange failing due to mismatching nonces ("TDLS:
FTIE ANonce in TPK M3 does not match with FTIE ANonce used in TPK M2").
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
Clear the peer information and disable the created link on a
failed TDLS setup negotiation. This is needed to avoid leaving
TDLS setup pending and to return to the AP path in case anything
goes wrong during the setup attempt.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
Some APs may incorrectly change Device Password ID from PBC in M1 to
Default PIN in M2 even when they are ready to continue with PBC. This
behavior used to work with earlier implementation in wpa_supplicant, but
commit b4a17a6ea7 started validating this
as part of a change that is needed to support NFC configuration method.
While this kind of AP behavior is against the WSC specification and
there could be potential use cases for moving from PBC to PIN, e.g., in
case of PBC session overlap, it is justifiable to work around this issue
to avoid interoperability issues with deployed APs. There are no known
implementations of PBC-to-PIN change from M1 to M2, so this should not
reduce available functionality in practice.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
It was possiblle for the group formation timeout to be left running even
after the P2P Client connected to the group if the WPS provisioning step
was not completed cleanly (e.g., due to WSC_Done not getting received
from the client). There is no need to remove the group in such case due
to the initial group formation timeout, so work around this by removing
that timeout on data connection.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
There was already a CFG_CHANGED_P2P_OPER_CHANNEL handler function, but
this flag was not set when the p2p_oper_reg_class or p2p_oper_channel
parameters were changed.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
wpa_supplicant crashes if driver configuration for AP mode interface
configuration fails after group negotiation. This is because of a
regression from commit 1075b29571 that
ends up freeing the wpa_s instance from within
wpa_supplicant_create_ap() without the caller knowing.
Fix this by using an eloop timeout to free remove the P2P group so that
wpa_supplicant_create_ap() and especially wpa_supplicant_associate()
callers do not need to know about interface getting possibly removed. In
addition, move the P2P specific code into p2p_supplicant.c where it
really belongs. This allows the already existing group formation timeout
to be used by reducing the timeout to zero.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
Some test runs have resulted in wpa_supplicant being unresponsive or
very slow on the control interface. Check for that type of issues as
part of the reset sequence that is done between each test case.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
Avoid potential issues with removing a P2P group on PSK failure directly
from the wpa_supplicant_event() call since the caller (in driver_*.c)
may not be prepared for the interface disappearing at that point in
time.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
test_persistent_group_invite_removed_client verifies that a client
that is removed from a group can rejoin based on new invitation.
Signed-hostap: Jouni Malinen <j@w1.fi>
It is possible for the GO of a persistent group to change the PSK or
remove a client when per-client PSKs are used and this can happen
without the SSID changing (i.e., the group is still valid, but just not
for a specific client). If the client side of such persistent group ends
up trying to use an invalidated persistent group information, the
connection will fail in 4-way handshake. A new WPS provisioning step is
needed to recover from this.
Detect this type of case based on two 4-way handshake failures when
acting as a P2P client in a persistent group. A new
"P2P-PERSISTENT-PSK-FAIL id=<persistent group id>" event is used to
indicate when this happens. This makes it easier for upper layers to
remove the persistent group information with "REMOVE_NETWORK <persistent
group id>" if desired (e.g., based on user confirmation).
In addition to indicating the error cases for persistent groups, all
this type of PSK failures end up in the client removing the group with
the new reason=PSK_FAILURE information in the P2P-GROUP-REMOVED event.
Signed-hostap: Jouni Malinen <j@w1.fi>
If a client joins a P2P group multiple times, replace the previous
per-client PSK entry instead of adding a new entry each time.
Signed-hostap: Jouni Malinen <j@w1.fi>
The new control interface command P2P_REMOVE_CLIENT <P2P Device
Address|iface=Address> can now be used to remove the specified client
from all groups (ongoing and persistent) in which the local device is a
GO. This will remove any per-client PSK entries and deauthenticate the
device.
Signed-hostap: Jouni Malinen <j@w1.fi>
Record all generated per-client PSKs in the persistent group network
block and configure these for the GO Authenticator whenever re-starting
the persistent group. This completes per-client PSK support for
persistent groups.
Signed-hostap: Jouni Malinen <j@w1.fi>
When using per-device PSKs, select the PSK based on the P2P Device
Address of the connecting client if that client is a P2P Device. This
allows the P2P Interface Address to be changed between P2P group
connections which may happen especially when using persistent groups.
Signed-hostap: Jouni Malinen <j@w1.fi>
This can be used to implement per-device PSK selection based on the
peer's P2P Device Address instead of P2P Interface Address.
Signed-hostap: Jouni Malinen <j@w1.fi>
This makes the P2P Device Address of the Enrollee available with the PSK
records to allow P2P Device Address instead of P2P Interface Address to
be used for finding the correct PSK.
Signed-hostap: Jouni Malinen <j@w1.fi>
"wpa_cli p2p_set per_sta_psk <0/1>" can now be used to disable/enable
use of per-device PSKs in P2P groups. This is disabled by default.
When enabled, a default passphrase is still generated by the GO for
legacy stations, but all P2P and non-P2P devices using WPS will get
a unique PSK.
This gives more protection for the P2P group by preventing clients from
being able to derive the unicast keys used by other clients. This is
also a step towards allowing specific clients to be removed from a group
reliably without having to tear down the full group to do so.
Signed-hostap: Jouni Malinen <j@w1.fi>
Even after listen duration is over, P2P module remained in
P2P_LISTEN_ONLY state, which is blocking station mode scans. Fix this by
stopping P2P listen explicitly to update p2p_state to IDLE when listen
duration expires.
Signed-hostap: Syed Asifful Dayyan <syedd@broadcom.com>
Use test_autogo to verify that P2P client is able to notice explicit
group session termination message from the GO. This would have caught
the regression in processing P2P deauthentication notifications.
Signed-hostap: Jouni Malinen <j@w1.fi>
wpa_cli filters out extra DISCONNECTED events from action scripts. This
ended up filtering out the first real DISCONNECT event in case wpa_cli
was started when wpa_supplicant was in connected state. Change wpa_cli
to allow the first disconnection event to be reported to the action
script in such case.
Signed-hostap: Jouni Malinen <j@w1.fi>
Some drivers fail to work if WEP keys are configured in a WPA network.
To avoid potentially confusing error cases, reject hostapd configuration
that enables WPA and includes parameters that would imply that WEP keys
would be set.
Signed-hostap: Jouni Malinen <j@w1.fi>
Previously, network added event was skipping during group formation.
However, this did not necessarily catch all cases of temporary P2P
network blocks. Check ssid->p2p_group to make this behavior more
consistent by avoiding all P2P groups.
Signed-hostap: Jouni Malinen <j@w1.fi>
