hostapd (and wpa_supplicant in AP mode) was internally updating the STA
flags on disconnection cases to remove authorization and association.
However, some cases did not result in immediate update of the driver STA
entry. Update all such cases to send out the update to the driver as
well to reduce risk of race conditions where new frames might be
accepted for TX or RX after the port authorization or association has
been lost and configured keys are removed.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
The new hostapd configuration parameter transition_disable can now be
used to configure the AP to advertise that use of a transition mode is
disabled. This allows stations to automatically disable transition mode
by disabling less secure network profile parameters.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
hostapd will trigger EDMG auto channel selection by setting
QCA_WLAN_VENDOR_ATTR_ACS_EDMG_ENABLED. The 60 GHz driver will be
called to start an auto channel selection and will return the
primary channel and the EDMG channel.
Signed-off-by: Noam Shaked <nshaked@codeaurora.org>
Support Extended Key ID in hostapd according to IEEE Std 802.11-2016.
Extended Key ID allows to rekey pairwise keys without the otherwise
unavoidable MPDU losses on a busy link. The standard is fully backward
compatible, allowing an AP to serve STAs with and without Extended Key
ID support in the same BSS.
Signed-off-by: Alexander Wetzel <alexander@wetzel-home.de>
There is no point in starting a huge number of pending SA Queries, so
limit the number of pending queries to 1000 to have an explicit limit
for how large sa_query_count can grow.
Signed-off-by: Jouni Malinen <j@w1.fi>
The new hostapd configuration parameter no_beacon_rsnxe=1 can be used to
remove RSNXE from Beacon frames. This can be used to test protection
mechanisms for downgrade attacks.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
The previous design for adding RSNXE into FT was not backwards
compatible. Move to a new design based on 20/332r3 to avoid that issue
by not include RSNXE in the FT protocol Reassociation Response frame so
that a STA not supporting RSNXE can still validate the FTE MIC
correctly.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Verify that the STA includes RSNXE if it indicated in FTE that RSNXE is
used and the AP is also using RSNXE. This is needed to protect against
downgrade attacks based on the design proposed in 20/332r3.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
This is a workaround needed to keep FT protocol backwards compatible for
the cases where either the AP or the STA uses RSNXE, but the other one
does not. This commit adds setting of the new field to 1 in
Reassociation Request/Response frame during FT protocol when the STA/AP
uses RSNXE in other frames. This mechanism is described in 20/332r3.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Commit 5f9b4afd ("Use frequency in HT/VHT validation steps done before
starting AP") modified hostapd_is_usable_edmg() to use freq instead of
channel numbers. Unfortunately, it did not convert the frequency
calculation correctly and this broke EDMG functionality.
Fix the frequency calculation so that EDMG channel 9 works again.
Fixes: 5f9b4afdfa ("Use frequency in HT/VHT validation steps done before starting AP")
Signed-off-by: Hrishikesh Vidwans <hvidwans@codeaurora.org>
Check whether an error is reported from any of the functions that could
in theory fail and if so, do not proceed with the partially filled SAE
commit buffer.
Signed-off-by: Jouni Malinen <j@w1.fi>
In theory, hmac_sha256() might fail, so check for that possibility
instead of continuing with undetermined index value that could point to
an arbitrary token entry.
Signed-off-by: Jouni Malinen <j@w1.fi>
send_auth_reply() could be called with sta == NULL in certain error
conditions. While that is not applicable for this special test
functionality for SAE, the inconsistent checks for the sta pointer could
result in warnings from static analyzers. Address this by explicitly
checking the sta pointer here.
Signed-off-by: Jouni Malinen <j@w1.fi>
mode->he_capab is an array and as such, there is no point in checking
whether it is NULL since that cannot be the case. Check for the
he_supported flag instead. In addition, convert the TWT responder
capability bit into a fixed value 1 to avoid any surprising to the
callers. In practice, neither of these changes results in different
behavior in the current implementation, but this is more robust.
Signed-off-by: Jouni Malinen <j@w1.fi>
The new hostapd configuration parameter rsne_override_eapol can now be
used similarly to the previously added rsnxe_override_eapol to override
(replace contents or remove) RSNE in EAPOL-Key msg 3/4. This can be used
for station protocol testing to verify sufficient checks for RSNE
modification between the Beacon/Probe Response frames and EAPOL-Key msg
3/4.
Signed-off-by: Jouni Malinen <j@w1.fi>
Previous implementation was determining whether the override value was
set based on its length being larger than zero. Replace this with an
explicit indication of whether the parameter is set to allow zero length
replacement, i.e., remove of RSNXE from EAPOL-Key msg 3/4.
In addition, move IE replacement into a more generic helper function to
allow this to be used with other IEs as well.
Signed-off-by: Jouni Malinen <j@w1.fi>
The 4-address frames WDS design in mac80211 uses VLAN interfaces
similarly to the way VLAN interfaces based on VLAN IDs are used. The EAP
authentication case ended up overriding the WDS specific assignment even
when the RADIUS server did not assign any specific VLAN for the STA.
This broke WDS traffic.
Fix this by skipping VLAN assignment to VLAN ID 0 for STAs that have
been detected to use 4-address frames.
Signed-off-by: Jouni Malinen <j@w1.fi>
After a radar signal is detected, the AP should switch to another
channel, but in the case of 80+80 MHz, channel switch failed because
hostapd did not select the secondary channel in the process. Fix this by
selecting a secondary channel in the case of 80+80 MHz.
Signed-off-by: Xin Wang <xwangw@codeaurora.org>
Signed-off-by: Pravas Kumar Panda <kumarpan@codeaurora.org>
The initial implementation of the PTK derivation workaround for
interoperability with older OWE implementations forced
WPA_KEY_MGMT_PSK_SHA256 to be used for all of PTK derivation. While that
is needed for selecting which hash algorithm to use, this was also
changing the length of the PTK components and by doing so, did not
actually address the backwards compatibility issue.
Fix this by forcing SHA256 as the hash algorithm in PTK derivation
without changing the PTK length calculation for OWE when
owe_ptk_workaround is enabled.
Fixes: 65a44e849a ("OWE: PTK derivation workaround in AP mode")
Fixes: 8b138d2826 ("OWE: PTK derivation workaround in STA mode")
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
hostapd_broadcast_wep_set() can be called without a WEP key set.
Don't try to install a default key in that case.
This patch is not critical for the new API. With key_flag we just would
report an (ignored) error and do nothing. With the patch we simply do
nothing.
Signed-off-by: Alexander Wetzel <alexander@wetzel-home.de>
This makes it easier to understand what is happening when a new channel
needs to be selected based on a radar detection event.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Upon radar detection we used to search channels with the same bandwidth.
This way we might not find any other channels. If there are no channels
available with that bandwidth the AP service will be stopped. To avoid
this problem, also search a suitable channel by downgrading the
bandwidth. This scenario is applicable during CAC as well.
Signed-off-by: Seevalamuthu Mariappan <seevalam@codeaurora.org>
In the normal case hostapd_disable_iface() and hostapd_enable_iface()
will be done while switching to another DFS channel upon radar
detection. In certain scenarios radar detected event can come while
hostapd_disable_iface() is in progress and iface->current_mode will be
NULL in that scenario. Previously, we did not check for this scenario
and proceeded with the radar detection logic which can trigger a
segmentation fault. To fix this, avoid proceeding the radar detection
event if iface->current_mode is NULL.
Signed-off-by: Seevalamuthu Mariappan <seevalam@codeaurora.org>
IEEE P802.11az/D2.0 renamed the FILS Wrapped Data element,
removing the FILS prefix. Change the code accordingly.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
PASN authentication can be performed while a station interface is
connected to an AP. To allow sending PASN frames while connected, extend
the send_mlme() driver callback to also allow a wait option. Update the
relevant drivers and wpa_supplicant accordingly.
hostapd calls for send_mlme() are left unchanged, since the wait option
is not required there.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
WEP should not be used for anything anymore. As a step towards removing
it completely, move all WEP related functionality to be within
CONFIG_WEP blocks. This will be included in builds only if CONFIG_WEP=y
is explicitly set in build configuration.
Signed-off-by: Jouni Malinen <j@w1.fi>
WEP provisioning was removed from WPS v2, so this workaround
functionality has not been applicable. Remove it completely.
Signed-off-by: Jouni Malinen <j@w1.fi>
This was already supported in the offload ACS case and this commit
completes support for this with the internal ACS algorithm.
Signed-off-by: Neo Jou <neojou@gmail.com>
Set iface->current_mode and iface->conf->hw_mode when completing ACS
based on the selected channel in the hw_mode=any case.
Signed-off-by: Neo Jou <neojou@gmail.com>
This is preparation for being able to support hw_mode=any to select the
best channel from any supported mode.
Signed-off-by: Neo Jou <neojou@gmail.com>
Add suitable channel frequencies from all modes into the scan parameters
when a single mode is not specified for ACS. This is preparation for
being able to support hw_mode=any to select the best channel from any
supported mode.
Signed-off-by: Neo Jou <neojou@gmail.com>
This is preparation for being able to support hw_mode=any to select the
best channel from any supported mode.
Signed-off-by: Neo Jou <neojou@gmail.com>
This is preparation for being able to support hw_mode=any to select the
best channel from any supported mode.
Signed-off-by: Neo Jou <neojou@gmail.com>
This is preparation for being able to support hw_mode=any to select the
best channel from any supported mode.
Signed-off-by: Neo Jou <neojou@gmail.com>
This is preparation for being able to support hw_mode=any to select the
best channel from any supported mode.
Signed-off-by: Neo Jou <neojou@gmail.com>
This is preparation for being able to support hw_mode=any to select the
best channel from any supported mode.
Signed-off-by: Neo Jou <neojou@gmail.com>
SAE authentication derives PMKID differently from the EAP cases. The
value comes from information exchanged during SAE authentication and
does not bind in the MAC addresses of the STAs. As such, the same PMKID
is used with different BSSIDs. Fix both the hostapd and wpa_supplicant
to use the previous PMKID as is for OKC instead of deriving a new PMKID
using an incorrect derivation method when using an SAE AKM.
This fixes use of opportunistic key caching with SAE.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
The cookie values for UDP control interface commands was defined as a
static global array. This did not allow multi-BSS test cases to be
executed with UDP control interface. For example, after
hapd1 = hostapd.add_bss(apdev[0], ifname1, 'bss-1.conf')
hapd2 = hostapd.add_bss(apdev[0], ifname2, 'bss-2.conf')
hapd1->ping() did not work.
Move those cookie values to per-instance location in struct
hapd_interfaces and struct hostapd_data to fix this.
Signed-off-by: Janusz Dziedzic <janusz.dziedzic@gmail.com>
Rekeying a pairwise key using only keyid 0 (PTK0 rekey) has many broken
implementations and should be avoided when using or interacting with
one. The effects can be triggered by either end of the connection and
range from hardly noticeable disconnects over long connection freezes up
to leaking clear text MPDUs.
To allow affected users to mitigate the issues, add a new hostapd
configuration option "wpa_deny_ptk0_rekey" to replace all PTK0 rekeys
with disconnection. This requires the station to reassociate to get
connected again and as such, can result in connectivity issues as well.
Signed-off-by: Alexander Wetzel <alexander@wetzel-home.de>
The MBO PMF check for AP SME in the driver case was added into a
location that is skipped for WPS processing. That was not really the
correct place for this since the skip_wpa_check label was supposed to
remain immediately following the WPA checks. While this does not really
have much of a practical impact, move the check around so that the
skip_wpa_check label remains where it is supposed to be.
Fixes: 4c572281ed ("MBO: Mandate use of PMF for WPA2+MBO association (AP)")
Signed-off-by: Jouni Malinen <j@w1.fi>
Save RM enabled capability element of an associating station when
hostapd use the device AP SME similarly to how this information is saved
with SME-on-hostapd cases. This allows radio measurement operations
(e.g., REQ_BEACON) to be used.
Signed-off-by: Ouden <Ouden.Biz@gmail.com>
This element is not used in Beacon or Probe Response frames (which is
the reason why the standard does not indicate where exactly it would be
in those frames..); HT Operation element has this information and so
does Extended CSA element.
In practice, this reverts the functionality added in commit 76aab0305c
("Add secondary channel IE for CSA").
Signed-off-by: Jouni Malinen <j@w1.fi>
Hardcoded CONFIG_IEEE80211N to be included to clean up implementation.
More or less all new devices support IEEE 802.11n (HT) and there is not
much need for being able to remove that functionality from the build.
Included this unconditionally to get rid of one more build options and
to keep things simpler.
Signed-off-by: Jouni Malinen <j@w1.fi>
Split the IEs from WPA authenticator state machine into separately added
IEs so that the exact location between these and other elements can be
controlled. This fixes the location of MDE and RSNXE in Beacon and Probe
Response frames. In addition, this swaps the order of BSS Load and RM
Enabled Capabilities elements in Beacon frames to get them into the
correct order (which was already used for Probe Response frames).
Furthermore, this fixes the buffer end checks for couple of elements to
make the implementation more consistent (though, in practice, there is
no impact from this since the old size limit was smaller than needed,
but still sufficiently large to have room for these).
Signed-off-by: Jouni Malinen <j@w1.fi>
Add a new hostapd configuration parameter beacon_prot=<0/1> to allow
Beacon protection to be enabled.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
SM Power Save was described in somewhat unclear manner in IEEE Std
802.11n-2009 as far the use of it locally in an AP to save power. That
was clarified in IEEE Std 802.11-2016 to allow only a non-AP STA to use
SMPS while the AP is required to support an associated STA doing so. The
AP itself cannot use SMPS locally and the HT Capability advertisement
for this is not appropriate.
Remove the parts of SMPS support that involve the AP using it locally.
In practice, this reverts the following commits:
04ee647d58 ("HT: Let the driver advertise its supported SMPS modes for AP mode")
8f461b50cf ("HT: Pass the smps_mode in AP parameters")
da1080d721 ("nl80211: Advertise and configure SMPS modes")
Signed-off-by: Jouni Malinen <j@w1.fi>
Set the proper bits inside the extended capabilities field to indicate
support for TWT responder.
Tested-by: John Crispin <john@phrozen.org>
Signed-off-by: Mikhail Karpenko <karpenko@fastmail.com>
The HE Operation field for BSS color consists of a disabled, a partial,
and 6 color bits. The original commit adding support for BSS color
considered this to be a u8. This commit changes this to the actual
bits/values.
This adds an explicit config parameter for the partial bit. The disabled
is set to 0 implicitly if a bss_color is defined.
Interoperability testing showed that stations will require a BSS color
to be set even if the feature is disabled. Hence the default color is 1
when none is defined inside the config file.
Signed-off-by: John Crispin <john@phrozen.org>
Commit 2bab073dfe ("WPS: Add new PSK entries with wps=1 tag") added
this when writing the new entry into a file, but the in-memory update
did not get the tag. Add it there as well.
Signed-off-by: Jouni Malinen <j@w1.fi>
Now that hostapd wpa_psk_file has a new tag for identifying PSKs that
can be used with WPS, add that tag to new entries for PSKs from WPS.
This makes it clearer where the PSK came from and in addition, this
allows the same PSK to be assigned if the same Enrollee goes through WPS
provisioning again.
Signed-off-by: Jouni Malinen <j@w1.fi>
By default, when configuration file set wpa_psk_file, hostapd generated
a random PSK for each Enrollee provisioned using WPS and appended that
PSK to wpa_psk_file.
Changes that behavior by adding a new step. WPS will first try to use a
PSK from wpa_psk_file. It will only try PSKs with wps=1 tag.
Additionally it'll try to match enrollee's MAC address (if provided). If
it fails to find an appropriate PSK, it falls back to generating a new
PSK.
Signed-off-by: Tomasz Jankowski <tomasz.jankowski@plume.com>
In the function owe_assoc_req_process(), values assigned to the reason
argument imply that it should be renamed to status. Rename 'reason' to
'status' and modify the uses of owe_assoc_req_process() accordingly.
Signed-off-by: Sergey Matyukevich <sergey.matyukevich.os@quantenna.com>
(Re)Association Response frames should include radio measurement
capabilities in order to let stations know if they can, e.g., use
neighbor requests.
I tested this commit with a Samsung S8, which does not send neighbor
requests without this commit and sends them afterwards.
Signed-off-by: Markus Theil <markus.theil@tu-ilmenau.de>
The new sae_pwe=3 mode can be used to test non-compliant behavior with
SAE Password Identifiers. This can be used to force use of
hunting-and-pecking loop for PWE derivation when Password Identifier is
used. This is not allowed by the standard and as such, this
functionality is aimed at compliance testing.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Only one peer-commit-scalar value was stored for a specific STA (i.e.,
one per MAC address) and that value got replaced when the next SAE
Authentication exchange was started. This ended up breaking the check
against re-use of peer-commit-scalar from an Accepted instance when
anti-clogging token was requested. The first SAE commit message (the one
without anti-clogging token) ended up overwriting the cached
peer-commit-scalar value while leaving that instance in Accepted state.
The second SAE commit message (with anti-clogging token) added ended up
getting rejected if it used the same value again (and re-use is expected
in this particular case where the value was not used in Accepted
instance).
Fix this by using a separate pointer for storing the peer-commit-scalar
value that was used in an Accepted instance. There is no need to
allocate memory for two values, i.e., it is sufficient to maintain
separate pointers to the value and move the stored value to the special
Accepted state pointer when moving to the Accepted state.
This fixes issues where a peer STA ends up running back-to-back SAE
authentication within couple of seconds, i.e., without hostapd timing
out the STA entry for a case where anti-clogging token is required.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Previously, hostapd ignored the secondary channel provided by ACS if
both HT40+ and HT40- are set in hostapd.conf. This change selects such
channel for HT40 if it's valid, which is more reasonable.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Add new control interface commands "DPP_NFC_HANDOVER_REQ own=<id>
uri=<URI>" and "DPP_NFC_HANDOVER_SEL own=<id> uri=<URI>" to support NFC
negotiated connection handover. These commands are used to report a DPP
URI received from a peer NFC Device in Handover Request and Handover
Select messages. The commands return peer bootstrapping information ID
or FAIL on failure. The returned ID is used similarly to any other
bootstrapping information to initiate DPP authentication.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Initial OWE implementation used SHA256 when deriving the PTK for all OWE
groups. This was supposed to change to SHA384 for group 20 and SHA512
for group 21. The new owe_ptk_workaround parameter can be used to enable
workaround for interoperability with stations that use SHA256 with
groups 20 and 21. By default, only the appropriate hash function is
accepted. When workaround is enabled (owe_ptk_workaround=1), the
appropriate hash function is tried first and if that fails, SHA256-based
PTK derivation is attempted. This workaround can result in reduced
security for groups 20 and 21, but is required for interoperability with
older implementations. There is no impact to group 19 behavior.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
IEEE P802.11-REVmd was modified to use a container IE for anti-clogging
token whenver H2E is used so that parsing of the SAE Authentication
frames can be simplified.
See this document for more details of the approved changes:
https://mentor.ieee.org/802.11/dcn/19/11-19-2154-02-000m-sae-anti-clogging-token.docx
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Based on the now documented seg0/seg1 values from offloaded ACS, there
is a mismatch between the driver interface and internal hostapd use.
The value of segment0 field in ACS results is the index of the channel
center frequency for 20 MHz, 40 MHz, and 80M Hz channels. The value is
the center frequency index of the primary 80 MHz segment for 160 MHz and
80+80 MHz channels.
The value of segment1 field in ACS results is zero for 20 MHz, 40 MHz,
and 80 MHz channels. The value is the index of the channel center
frequency for 160 MHz channels and the center frequency index of the
secondary 80 MHz segment for 80+80 MHz channels.
However, in struct hostapd_config, for 160 MHz channels, the value of
the segment0 field is the index of the channel center frequency of 160
MHz channel and the value of the segment1 field is zero. Map the values
from ACS event into hostapd_config fields accordingly.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
The Channel Width field value is 0 for 20 MHz, 1 for 40 MHz, 2 for 80
MHz, and 3 for both 160 MHz and 80+80 MHz channels. The 80+80 MHz case
was not addressed previously correctly since it cannot be derived from
seg0 only.
The Channel Center Frequency Segment 0 field value is the index of
channel center frequency for 20 MHz, 40 MHz, and 80 MHz channels. The
value is the center frequency index of the primary 80 MHz segment for
160 MHz and 80+80 MHz channels.
The Channel Center Frequency Segment 1 field value is zero for 20 MHz,
40 MHz, and 80 MHz channels. The value is the index of the channel
center frequency for 160 MHz channel and the center frequency index of
the secondary 80 MHz segment for 80+80 MHz channels.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Make the dummy hostapd_hw_mode_txt() wrapper return "UNKNOWN" instead of
NULL to avoid a warning from a debug printf using %s with NULL.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Add the new set_key() parameter "key_flag" to provide more specific
description of what type of a key is being configured. This is needed to
be able to add support for "Extended Key ID for Individually Addressed
Frames" from IEEE Std 802.11-2016. In addition, this may be used to
replace the set_tx boolean eventually once all the driver wrappers have
moved to using the new key_flag.
The following flag are defined:
KEY_FLAG_MODIFY
Set when an already installed key must be updated.
So far the only use-case is changing RX/TX status of installed
keys. Must not be set when deleting a key.
KEY_FLAG_DEFAULT
Set when the key is also a default key. Must not be set when
deleting a key. (This is the replacement for set_tx.)
KEY_FLAG_RX
The key is valid for RX. Must not be set when deleting a key.
KEY_FLAG_TX
The key is valid for TX. Must not be set when deleting a key.
KEY_FLAG_GROUP
The key is a broadcast or group key.
KEY_FLAG_PAIRWISE
The key is a pairwise key.
KEY_FLAG_PMK
The key is a Pairwise Master Key (PMK).
Predefined and needed flag combinations so far are:
KEY_FLAG_GROUP_RX_TX
WEP key not used as default key (yet).
KEY_FLAG_GROUP_RX_TX_DEFAULT
Default WEP or WPA-NONE key.
KEY_FLAG_GROUP_RX
GTK key valid for RX only.
KEY_FLAG_GROUP_TX_DEFAULT
GTK key valid for TX only, immediately taking over TX.
KEY_FLAG_PAIRWISE_RX_TX
Pairwise key immediately becoming the active pairwise key.
KEY_FLAG_PAIRWISE_RX
Pairwise key not yet valid for TX. (Only usable with Extended Key ID
support.)
KEY_FLAG_PAIRWISE_RX_TX_MODIFY
Enable TX for a pairwise key installed with KEY_FLAG_PAIRWISE_RX.
KEY_FLAG_RX_TX
Not a valid standalone key type and can only used in combination
with other flags to mark a key for RX/TX.
This commit is not changing any functionality. It just adds the new
key_flag to all hostapd/wpa_supplicant set_key() functions without using
it, yet.
Signed-off-by: Alexander Wetzel <alexander@wetzel-home.de>
If the driver supports VLAN offload mechanism with a single netdev, use
that instead of separate per-VLAN netdevs.
Signed-off-by: Gurumoorthi Gnanasambandhan <gguru@codeaurora.org>
This is in preparation for adding support to use a single WLAN netdev
with VLAN operations offloaded to the driver. No functional changes are
included in this commit.
Signed-off-by: Gurumoorthi Gnanasambandhan <gguru@codeaurora.org>
This makes it more convenient to add, remove, and modify the parameters
without always having to update every single driver_*.c implementation
of this callback function.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
sae_confirm_immediate=2 can now be used in CONFIG_TESTING_OPTIONS=y
builds to minimize the latency between SAE Commit and SAE Confirm by
postponing transmission of SAE Commit until the SAE Confirm frame is
generated. This does not have significant impact, but can get the frames
tiny bit closer to each other over the air to increase testing coverage.
The only difference between sae_confirm_immediate 1 and 2 is in the
former deriving KCK, PMK, PMKID, and CN between transmission of the
frames (i.e., a small number of hash operations).
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
This was used only for FT RRB sending with driver_test.c and
driver_test.c was removed more than five years ago, so there is no point
in continuing to maintain this driver op.
Signed-off-by: Jouni Malinen <j@w1.fi>
Application Extension attribute is defined in WSC tech spec v2.07 page
104. Allow hostapd to be configured to add this extension into WPS IE in
Beacon and Probe Response frames. The implementation is very similar to
vendor extension.
A new optional entry called "wps_application_ext" is added to hostapd
config file to configure this. It enodes the payload of the Application
Extension attribute in hexdump format.
Signed-off-by: Veli Demirel <veli.demirel@airties.com>
Signed-off-by: Bilal Hatipoglu <bilal.hatipoglu@airties.com>
The new hostapd gtk_rsc_override and igtk_rsc_override configuration
parameters can be used to set an override value for the RSC that the AP
advertises for STAs for GTK/IGTK. The contents of those parameters is a
hexdump of the RSC in little endian byte order.
This functionality is available only in CONFIG_TESTING_OPTIONS=y builds.
This can be used to verify that stations implement initial RSC
configuration correctly for GTK/ and IGTK.
Signed-off-by: Jouni Malinen <j@w1.fi>
Since send_mlme() now has support for the no_encrypt argument it is
possible to get rid of the remaining send_frame() uses.
Signed-off-by: Jouni Malinen <j@w1.fi>
Merge hostapd_drv_send_mlme_csa() functionality into
hostapd_drv_send_mlme() to get a single driver ops handler function for
hostapd. In addition, add a new no_encrypt parameter in preparation for
functionality that is needed to get rid of the separate send_frame()
driver op.
Signed-off-by: Jouni Malinen <j@w1.fi>
send_frame() is documented to be used for "testing use only" and as
such, it should not have used here for a normal production
functionality. Replace this with use of send_mlme() which is already
used for sending Deauthentication frames in other cases.
Signed-off-by: Jouni Malinen <j@w1.fi>
These are certainly not error conditions, but normal cases for starting
up. Drop the message from ERROR to DEBUG.
Signed-off-by: Jouni Malinen <j@w1.fi>
ieee802_11_allowed_address() did not really do anything useful for the
call from handle_probe_req(), so replace that with a direct call to
hostapd_allowed_address() and make ieee802_11_allowed_address() a static
function.
Signed-off-by: Jouni Malinen <j@w1.fi>
When returning from handle_auth() after ieee802_11_allowed_address()
returned HOSTAPD_ACL_ACCEPT, but before ieee802_11_set_radius_info() has
been called, identity, radius_cui, and psk might not have been consumed.
Fix this by avoiding the need to free these variables at all.
Signed-off-by: Michael Braun <michael-dev@fami-braun.de>
For FT protocol to work, the BSSs need to be operating an FT AKM with
the same SSID and mobility domain. The previous commit covered the
mobility domain, this covers the other prerequisites. This reduces
unnecessary load from having to allocate queued messages for interfaces
that cannot have valid data.
Signed-off-by: Jouni Malinen <j@w1.fi>
Fast BSS Transition requires related APs operating in the same mobility
domain. Therefore, we can check whether the local managed BSS is
operating the same mobility domain before sending multicast/unicast
messages to it. This reduces unnecessary load from having to allocate
queued messages for interfaces that cannot have valid data.
Signed-off-by: Jinglin Wang <bryanwang@synology.com>
Signed-off-by: MinHong Wang <minhongw@synology.com>
This makes it easier to figure out how frames are delivered directly
between BSSs operated within a single hostapd process.
Signed-off-by: Jouni Malinen <j@w1.fi>
Add new messages to the end of the l2_oui_queue instead of inserting
them at the beginning so that the dl_list_for_each_safe() iteration in
hostapd_oui_deliver_later() goes through the messages in the same order
they were originally queued.
Signed-off-by: Jouni Malinen <j@w1.fi>
