Commit graph

4258 commits

Author SHA1 Message Date
Kyeyoon Park
47261405d7 AP: Add support for multicast-to-unicast conversion for DGAF Disable
When DGAF Disable is on, perform multicast-to-unicast for DHCP packets
and Router Advertisement packets. This is a requirement for Hotspot 2.0.

Signed-off-by: Kyeyoon Park <kyeyoonp@qca.qualcomm.com>
2014-11-19 16:47:06 +02:00
Kyeyoon Park
bd00c4311c AP: Add Neighbor Discovery snooping mechanism for Proxy ARP
This commit establishes the infrastructure, and handles the Neighbor
Solicitation and Neighbor Advertisement frames. This will be extended
in the future to handle other frames.

Signed-off-by: Kyeyoon Park <kyeyoonp@qca.qualcomm.com>
2014-11-19 16:47:06 +02:00
Kyeyoon Park
5c58944d08 AP: Add multicast-to-unicast conversion send for "x_snoop"
Multicast-to-unicast conversion send will be needed in various part of
Proxy ARP and DGAF Disable.

Signed-off-by: Kyeyoon Park <kyeyoonp@qca.qualcomm.com>
2014-11-19 16:25:13 +02:00
Kyeyoon Park
ed4ddb6d77 AP: Extend the BSS bridge neighbor entry management to support IPv6
This allows adding/deleting an IPv6 neighbor entry to/from the bridge,
to which the BSS belongs. This commit adds the needed functionality in
driver_nl80211.c for the Linux bridge implementation. In theory, this
could be shared with multiple Linux driver interfaces, but for now, only
the main nl80211 interface is supported.

Signed-off-by: Kyeyoon Park <kyeyoonp@qca.qualcomm.com>
2014-11-19 16:23:38 +02:00
Kyeyoon Park
7e4d893978 l2_packet: Add support for NDISC packet filter in l2_packet_linux
Signed-off-by: Kyeyoon Park <kyeyoonp@qca.qualcomm.com>
2014-11-19 16:15:26 +02:00
Kyeyoon Park
1d783762cf AP: Convert "dhcp_snoop" to use the generic "x_snoop"
Signed-off-by: Kyeyoon Park <kyeyoonp@qca.qualcomm.com>
2014-11-19 16:14:15 +02:00
Kyeyoon Park
c127355cb8 AP: Add a generic "x_snoop" infrastructure for Proxy ARP
Signed-off-by: Kyeyoon Park <kyeyoonp@qca.qualcomm.com>
2014-11-19 16:14:02 +02:00
Ilan Peer
38cb0a2db6 AP: Drop retransmitted auth/assoc/action frames
It is possible that a station device might miss an ACK for an
authentication, association, or action frame, and thus retransmit the
same frame although the frame is already being processed in the stack.
While the duplicated frame should really be dropped in the kernel or
firmware code where duplicate detection is implemented for data frames,
it is possible that pre-association cases are not fully addressed (which
is the case at least with mac80211 today) and the frame may be delivered
to upper layer stack.

In such a case, the local AP will process the retransmitted frame although
it has already handled the request, which might cause the station to get
confused and as a result disconnect from the AP, blacklist it, etc.

To avoid such a case, save the sequence control of the last processed
management frame and in case of retransmissions drop them.

Signed-off-by: Ilan Peer <ilan.peer@intel.com>
2014-11-19 15:20:47 +02:00
Jouni Malinen
453553698c EAP-pwd: Remove unnecessary OpenSSL EVP_sha256() registration
This gets registered in tls_openssl.c from tls_init(), so there is no
need for EAP-pwd implementation to register explicitly. This avoids some
corner cases where OpenSSL resources do not get fully freed on exit.

Signed-off-by: Jouni Malinen <j@w1.fi>
2014-11-17 01:20:10 +02:00
Jouni Malinen
afbe57d981 DFS: Fix hostapd operation without hw_mode driver data
If DFS implementation was built in, some configurations with drivers
that do not provide mode information could end up dereferencing a NULL
pointer. Fix this by skipping DFS operations in such cases since not
having information about modes and channels means that hostapd could not
perform DFS anyway (i.e., either this is not a wireless driver or the
driver takes care of DFS internally).

Signed-off-by: Jouni Malinen <j@w1.fi>
2014-11-17 01:14:35 +02:00
Jouni Malinen
e9b783d58c Fix hostapd operation without hw_mode driver data
Commit 7f0303d5b0 ('hostapd: Verify VHT
160/80+80 MHz driver support') added couple of hapd->iface->current_mode
dereferences of which the one in hostapd_set_freq() can be hit with some
configuration files when using driver wrappers that do not have hw_mode
data, i.e., when current_mode is NULL. This could result in segmentation
fault when trying to use driver=wired. Fix this by checking that
current_mode is not NULL before dereferencing it to get vht_capab.

Signed-off-by: Jouni Malinen <j@w1.fi>
2014-11-17 01:08:04 +02:00
Jouni Malinen
01b24c52df wired: Fix deinit path to unregister eloop read_sock
The previous version was leaving behind registered eloop socket
instances.

Signed-off-by: Jouni Malinen <j@w1.fi>
2014-11-17 00:57:15 +02:00
Moshe Benji
71d263ea70 Add wpa_scnprintf() helper function
This provides a simpler version of snprintf that doesn't require further
error checks.

Signed-off-by: Moshe Benji <moshe.benji@intel.com>
Signed-off-by: Eliad Peller <eliad@wizery.com>
2014-11-16 21:40:42 +02:00
Moshe Benji
dfa8787833 nl80211: Implement add_ts/del_ts ops
Add ops to notify about TSPECs to add/remove. Additionally, subscribe to
ADDTS/DELTS Action frames to be able to process WMM AC Action frames.

Signed-off-by: Moshe Benji <moshe.benji@intel.com>
Signed-off-by: Eliad Peller <eliad@wizery.com>
2014-11-16 21:21:22 +02:00
Eliad Peller
1b640fd27c Add str_token() function
Add helper function to get the next token from a string.

Signed-off-by: Eliad Peller <eliadx.peller@intel.com>
2014-11-16 21:11:23 +02:00
Moshe Benji
d1f880013a WMM AC: Handle TSPEC action frames
Add the TSPEC to the driver on successful TSPEC ADDTS response. Delete
the TSPEC when receiving DELTS action.

Signed-off-by: Moshe Benji <moshe.benji@intel.com>
Signed-off-by: Eliad Peller <eliad@wizery.com>
2014-11-16 21:07:08 +02:00
Moshe Benji
471cd6e10c WMM AC: Add add_tx_ts and del_tx_ts driver ops
Add add_tx_ts() and del_tx_ts() ops to notify the driver about
TSPEC add / delete.

Additionally, add wmm_ac_supported flag to indicate
whether the driver supports WMM AC.

Signed-off-by: Moshe Benji <moshe.benji@intel.com>
Signed-off-by: Eliad Peller <eliad@wizery.com>
2014-11-16 20:47:36 +02:00
Moshe Benji
a0413b1734 WMM AC: Parse WMM IE on association
Initialize WMM AC data structures upon successful association
with an AP that publishes WMM support, and deinitialize the data
structure when the association is no longer valid.

Signed-off-by: Moshe Benji <moshe.benji@intel.com>
Signed-off-by: Eliad Peller <eliadx.peller@intel.com>
2014-11-16 20:47:34 +02:00
Eliad Peller
7e0e10693a nl80211: Parse WMM parameters on association
Set the relevant WMM parameters in the assoc_data event.

Signed-off-by: Eliad Peller <eliadx.peller@intel.com>
2014-11-16 20:19:04 +02:00
Eliad Peller
0f14a44e6b drivers: Add WMM parameters to association event data
The WMM parameters will be used later for setting default tspec values.

Signed-off-by: Eliad Peller <eliadx.peller@intel.com>
2014-11-16 20:16:58 +02:00
Jouni Malinen
d308d1a899 Sync with wireless-testing.git include/uapi/linux/nl80211.h
This brings in nl80211 definitions as of 2014-11-11.

Signed-off-by: Jouni Malinen <j@w1.fi>
2014-11-16 20:08:00 +02:00
Masashi Honma
e609679984 mesh: Make plink params configurable
This patch makes four MIB variables for plink configurable and sets the
correct default values based on IEEE Std 802.11s-2011.

Signed-off-by: Masashi Honma <masashi.honma@gmail.com>
2014-11-16 19:43:11 +02:00
Masashi Honma
790709060d mesh: Add scan result for mesh network
Android 4.4 uses "BSS" command instead of "SCAN_RESULT" command.
So this patch add the mesh scan result for BSS command.

Signed-off-by: Masashi Honma <masashi.honma@gmail.com>
2014-11-16 19:43:11 +02:00
Javier Lopez
603a3f34c4 Add mesh_group_{add,remove} control interface commands
Parse MESH_GROUP_ADD/REMOVE commands on ctrl interface and call
wpa_supplicant routines. These commands are used to start or
join and leave a mesh network.

The mesh id is given in the configuration file, therefore there is
no need to scan before joining a mesh network. We reuse the
connect_without_scan construct used by P2P for that same purpose.

Signed-off-by: Javier Cardona <javier@cozybit.com>
Signed-off-by: Javier Lopez <jlopex@gmail.com>
2014-11-16 19:43:11 +02:00
Jason Mobarak
5cfb672dde mesh: Enable mesh HT mode
Add a new option "mesh_ht_mode" that specifies the HT mode for the
mesh, with this option on, mesh beacons, actions frames, and probe
responses with include the appropriate HT information elements.

[original implementation by Chun-Yeow Yeoh <yeohchunyeow@gmail.com>]
[some fixes by Masashi Honma <masashi.honma@gmail.com>]
Signed-off-by: Ashok Nagarajan <ashok.dragon@gmail.com>
Signed-off-by: Javier Cardona <javier@cozybit.com>
Signed-off-by: Jason Mobarak <x@jason.mobarak.name>
2014-11-16 19:43:11 +02:00
Chun-Yeow Yeoh
c596f3f083 mesh: Add timer for SAE authentication in RSN mesh
Add timer to do SAE re-authentication with number of tries defined
by MESH_AUTH_RETRY and timeout defined by MESH_AUTH_TIMEOUT.

Ignoring the sending of reply message on "SAE confirm before commit"
to avoid "ping-pong" issues with other mesh nodes. This is obvious when
number of mesh nodes in MBSS reaching 6.

Signed-off-by: Chun-Yeow Yeoh <yeohchunyeow@gmail.com>
Signed-off-by: Bob Copeland <me@bobcopeland.com>
2014-11-16 19:43:11 +02:00
Bob Copeland
c50d94f1f8 mesh: Start mesh peering after successful authentication
[original patch by: Thomas Pedersen <thomas@noack.us>]
Signed-off-by: Bob Copeland <me@bobcopeland.com>
2014-11-16 19:43:11 +02:00
Bob Copeland
e96da42b0e SAE: Enhance AP implementation to handle auth for mesh interfaces
Add state transition logic to the SAE frame handling in order to more
fully implement the state machine from the IEEE 802.11 standard. Special
cases are needed for infrastructure BSS case to avoid unexpected
Authentication frame sequence by postponing transmission of the second
Authentication frame untile the STA sends its Confirm.

[original patch by: Thomas Pedersen <thomas@noack.us>]
Signed-off-by: Bob Copeland <me@bobcopeland.com>
2014-11-16 19:43:11 +02:00
Thomas Pedersen
0f950df029 mesh: Add mesh robust security network
This implementation provides:

- Mesh SAE authentication mechanism
- Key management (set/get PSK)
- Cryptographic key establishment
- Enhanced protection mechanisms for robust management frames

Signed-off-by: Javier Lopez <jlopex@gmail.com>
Signed-off-by: Javier Cardona <javier@cozybit.com>
Signed-off-by: Jason Mobarak <x@jason.mobarak.name>
Signed-off-by: Thomas Pedersen <thomas@noack.us>
2014-11-16 19:43:06 +02:00
Dmitry Shmidt
88cb27c7a5 hostapd: Add wowlan_triggers config param
New kernels in wiphy_suspend() will call cfg80211_leave_all() that will
eventually end up in cfg80211_stop_ap() unless wowlan_triggers were set.
For now, use the parameters from the station mode as-is. It may be
desirable to extend (or constraint) this in the future for specific AP
mode needs.

Signed-off-by: Dmitry Shmidt <dimitrysh@google.com>
2014-11-16 17:09:11 +02:00
Ilan Peer
f03996565a nl80211: Fix Android compilation by adding include for fcntl.h
This is needed for fcntl() at least with Android KK.

Signed-off-by: Ilan Peer <ilan.peer@intel.com>
2014-11-16 17:09:11 +02:00
Jouni Malinen
929a2ea5df Suite B: Select EAPOL-Key integrity and key-wrap algorithms based on AKM
This adds support for AKM 00-0F-AC:11 to specify the integrity and
key-wrap algorithms for EAPOL-Key frames using the new design where
descriptor version is set to 0 and algorithms are determined based on
AKM.

Signed-off-by: Jouni Malinen <j@w1.fi>
2014-11-16 17:09:11 +02:00
Jouni Malinen
087a1f4efd Suite B: PMKID derivation for AKM 00-0F-AC:11
The new AKM uses a different mechanism of deriving the PMKID based on
KCK instead of PMK. hostapd was already doing this after the KCK had
been derived, but wpa_supplicant functionality needs to be moved from
processing of EAPOL-Key frame 1/4 to 3/4 to have the KCK available.

Signed-off-by: Jouni Malinen <j@w1.fi>
2014-11-16 17:09:11 +02:00
Jouni Malinen
666497c8e6 Suite B: Add AKM 00-0F-AC:11
This adds definitions for the 128-bit level Suite B AKM 00-0F-AC:11. The
functionality itself is not yet complete, i.e., this commit only
includes parts to negotiate the new AKM.

Signed-off-by: Jouni Malinen <j@w1.fi>
2014-11-16 13:20:51 +02:00
Jouni Malinen
35efa2479f OpenSSL: Allow TLS v1.1 and v1.2 to be negotiated by default
Use SSLv23_method() to enable TLS version negotiation for any version
equal to or newer than 1.0. If the old behavior is needed as a
workaround for some broken authentication servers, it can be configured
with phase1="tls_disable_tlsv1_1=1 tls_disable_tlsv1_2=1".

Signed-off-by: Jouni Malinen <j@w1.fi>
2014-11-15 12:35:10 +02:00
Andrei Otcheretianski
281ff42a01 EAP-IKEv2: Fix compilation warning
Fix signed/unsigned comparison compilation warning introduced in
08ef442 "EAP-IKEv2: Fix the payload parser".

Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
2014-11-15 11:41:09 +02:00
Dmitry Shmidt
d10792199e Add CTRL-EVENT-SCAN-FAILED notification in case of scan failure
This is needed since the SCAN command with radio work returns before the
actual driver operation to trigger a scan has been executed and as such,
cannot return result of that operation.

Signed-off-by: Dmitry Shmidt <dimitrysh@google.com>
2014-11-15 11:03:52 +02:00
Jouni Malinen
9f6a7cddc4 Work around AP misbehavior on EAPOL-Key descriptor version
It looks like some APs are incorrectly selecting descriptor version 3
(AES-128-CMAC) for EAPOL-Key frames when version 2 (HMAC-SHA1) was
expected to be used. This is likely triggered by an attempt to negotiate
PMF with SHA1-based AKM.

Since AES-128-CMAC is considered stronger than HMAC-SHA1, allow the
incorrect, but stronger, option to be used in these cases to avoid
interoperability issues with deployed APs.

This issue shows up with "WPA: CCMP is used, but EAPOL-Key descriptor
version (3) is not 2" in debug log. With the new workaround, this issue
is ignored and "WPA: Interoperability workaround: allow incorrect
(should have been HMAC-SHA1), but stronger (is AES-128-CMAC), descriptor
version to be used" is written to the log.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2014-11-14 21:01:13 +02:00
Yanbo Li
e3a8ad4405 hostapd: Change drv_flags from unsigned int to u64
Some flag already using a bit larger than 32, so extend the hostapd
drv_flags type similarly to the earlier wpa_supplicant change to get the
full flag content.

Signed-off-by: Yanbo Li <yanbol@qti.qualcomm.com>
2014-11-14 12:55:53 +02:00
Jouni Malinen
41a233572e Assign QCA vendor specific nl80211 command id 52 for APFIND
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2014-11-13 16:27:23 +02:00
Jouni Malinen
68ee1cdca0 Remove unused EVENT_MLME_RX
This was used in driver_test.c, but that driver wrapper has been removed
and there are no remaining or expected users for EVENT_MLME_RX.

Signed-off-by: Jouni Malinen <j@w1.fi>
2014-11-01 19:31:23 +02:00
Jouni Malinen
0f812c993b Remove unused EVENT_FT_RRB_RX
This was used in hostapd driver_test.c, but that driver wrapper has been
removed and there are no remaining or expected users for
EVENT_FT_RRB_RX.

Signed-off-by: Jouni Malinen <j@w1.fi>
2014-11-01 19:27:48 +02:00
Jouni Malinen
f21495ad38 madwifi: Remove obsolete madwifi driver interface
The MadWifi project is not active anymore and the last release happened
in early 2008. As such, there is no remaining justification for
maintaining the madwifi-specific driver interface for hostapd either.

Signed-off-by: Jouni Malinen <j@w1.fi>
2014-11-01 16:15:29 +02:00
Jouni Malinen
b5ea99377f P2P: Document p2p_in_progress() return value 2
Function documentation was not in sync with the implementation.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2014-10-31 00:50:01 +02:00
Sunil Dutt
b951a97454 P2P: Set p2p_scan_running based on driver scan request result
With the radio work interface, the actual request to start p2p_scan
operation is scheduled from a radio work and hence the initial return
value cannot provide the real result of the driver operation to trigger
a scan. Introduce a new notification API to indicate the scan trigger
status based on which the p2p_scan_running instance can be set using the
real return value from the driver operation.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2014-10-31 00:05:25 +02:00
Jouni Malinen
43d8592718 MACsec: Fix policy configuration
macsec_validate variable was set incorrectly to FALSE(0) or TRUE(1)
instead of the enum validate_frames values (Disabled(0), Checked(1),
Strict(2). This ended up policy == SHOULD_SECURE to be mapped to
macsec_validate == Checked instead of Strict. This could have resulted
in unintended SecY forwarding of invalid packets rather than dropping
them.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2014-10-30 11:43:47 +02:00
Jouni Malinen
8c00fd00cd P2P: Clean up p2p_go_neg_failed() calls
This function is always called with the peer argument equal to
p2p->go_neg_peer, so there is no need for that argument to be there. In
addition, p2p->go_neg_peer is not NULL in cases where there is an
ongoing GO Negotiation, so the function can be simplified to just check
once whether the peer pointer is set and if not, skip all processing.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2014-10-29 13:04:09 +02:00
Rashmi Ramanna
0c6eee8b75 P2P: Use timer to fail GO Negotation while waiting for peer
The timeout check while waiting for the peer to accept the GO
Negotiation depended on the WAIT_PEER_IDLE or WAIT_PEER_CONNECT states
being in use. Any P2P command to alter such states would have resulted
in the failure to time out GO Negotiation and thus ended up in not
indicating GO Negotiation failure or left the selected peer available
for new GO negotiation after the expected two minute timeout.

Fix this by using a separate timer to time out GO Negotiation
irrespective of the P2P state.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2014-10-29 12:50:32 +02:00
Jouni Malinen
10bbe8b8ed nl80211: Fix a copy-paste error in key offload management
Commit b41f26845a ('Add support for
offloading key management operations to the driver') used incorrect
variable for determining the KCK length. This does not get triggered in
normal use cases since KCK and KEK are always included and of the same
length (in currently supported key management cases). Anyway, this needs
to be fixed to check the correct attribute. (CID 74491)

Signed-off-by: Jouni Malinen <j@w1.fi>
2014-10-28 01:41:57 +02:00
Kyeyoon Park
7d597d4617 AP: Add support for Proxy ARP, DHCP snooping mechanism
Proxy ARP allows the AP devices to keep track of the hardware address to
IP address mapping of the STA devices within the BSS. When a request for
such information is made (i.e., ARP request, Neighbor Solicitation), the
AP will respond on behalf of the STA device within the BSS. Such
requests could originate from a device within the BSS or also from the
bridge. In the process of the AP replying to the request (i.e., ARP
reply, Neighbor Advertisement), the AP will drop the original request
frame. The relevant STA will not even know that such information was
ever requested.

This feature is a requirement for Hotspot 2.0, and is defined in IEEE
Std 802.11-2012, 10.23.13. While the Proxy ARP support code mainly
resides in the kernel bridge code, in order to optimize the performance
and simplify kernel implementation, the DHCP snooping code was added to
the hostapd.

Signed-off-by: Kyeyoon Park <kyeyoonp@qca.qualcomm.com>
2014-10-28 01:08:29 +02:00
Kyeyoon Park
6897556455 common: Add definition for ETH_HLEN
Signed-off-by: Kyeyoon Park <kyeyoonp@qca.qualcomm.com>
2014-10-28 01:08:29 +02:00
Kyeyoon Park
7565752d47 AP: Add support for setting bridge network parameter
This allows setting a network parameter on the bridge that the BSS
belongs to.

This commit adds the needed functionality in driver_nl80211.c for the
Linux bridge implementation. In theory, this could be shared with
multiple Linux driver interfaces, but for now, only the main nl80211
interface is supported.

Signed-off-by: Kyeyoon Park <kyeyoonp@qca.qualcomm.com>
2014-10-28 01:08:29 +02:00
Kyeyoon Park
73d2294fbe AP: Add support for setting bridge port attributes
This allows setting a bridge port attribute. Specifically, the bridge
port in this context is the port to which the BSS belongs.

This commit adds the needed functionality in driver_nl80211.c for the
Linux bridge implementation. In theory, this could be shared with
multiple Linux driver interfaces, but for now, only the main nl80211
interface is supported.

Signed-off-by: Kyeyoon Park <kyeyoonp@qca.qualcomm.com>
2014-10-28 01:08:29 +02:00
Kyeyoon Park
71103bed42 AP: Add support for IPv4 neighbor entry management to the BSS bridge
This allows adding/deleting an IPv4 neighbor entry to/from the bridge,
to which the BSS belongs. This commit adds the needed functionality in
driver_nl80211.c for the Linux bridge implementation. In theory, this
could be shared with multiple Linux driver interfaces, but for now, only
the main nl80211 interface is supported.

Signed-off-by: Kyeyoon Park <kyeyoonp@qca.qualcomm.com>
2014-10-28 01:08:29 +02:00
Kyeyoon Park
6c6678e7a4 nl80211: Make br_ifindex available in i802_bss
Signed-off-by: Kyeyoon Park <kyeyoonp@qca.qualcomm.com>
2014-10-28 01:08:29 +02:00
Kyeyoon Park
7d20dd66f3 l2_packet: Add support for DHCP packet filter in l2_packet_linux
Signed-off-by: Kyeyoon Park <kyeyoonp@qca.qualcomm.com>
2014-10-28 01:08:29 +02:00
Ahmad Masri
d77419d234 P2P: Support GCMP as part of 60 GHz support
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2014-10-27 17:15:09 +02:00
Jouni Malinen
159a17916f nl80211: Move more event processing into driver_nl80211_event.c
Signed-off-by: Jouni Malinen <j@w1.fi>
2014-10-26 17:54:56 +02:00
Jouni Malinen
8a906d1251 nl80211: Move event handling into a separate file
Signed-off-by: Jouni Malinen <j@w1.fi>
2014-10-26 17:54:56 +02:00
Jouni Malinen
0fafeb5454 nl80211: Move capability determination into a separate file
This moves significant amount of code away from large driver_nl80211.c.

Signed-off-by: Jouni Malinen <j@w1.fi>
2014-10-26 17:54:56 +02:00
Jouni Malinen
906bc4c7d3 nl80211: Move QCA DFS offload capability determination to init time
There is no need to fetch this capability for each get_capa() call.

Signed-off-by: Jouni Malinen <j@w1.fi>
2014-10-26 17:54:56 +02:00
Jouni Malinen
981cf85a41 nl80211: Move AP monitor interface handling to a separate file
This moves the old monitor interface design to driver_nl80211_monitor.c.

Signed-off-by: Jouni Malinen <j@w1.fi>
2014-10-26 17:54:56 +02:00
Jouni Malinen
f3407c66c2 nl80211: Make some helper functions non-static
This allows more functionality to be moved to separate files.

Signed-off-by: Jouni Malinen <j@w1.fi>
2014-10-26 17:54:56 +02:00
Jouni Malinen
70a96c8116 nl80211: Move most of the Android code into a separate file
This moves most of the Android specific implementation from
driver_nl80211.c to driver_nl80211_android.c.

Signed-off-by: Jouni Malinen <j@w1.fi>
2014-10-26 17:54:56 +02:00
Jouni Malinen
1474e6e917 nl80211: Move definitions into separate header files
This is an initial step in starting to split the large driver_nl80211.c
implementation into somewhat smaller parts.

Signed-off-by: Jouni Malinen <j@w1.fi>
2014-10-26 17:03:24 +02:00
Jouni Malinen
2f06bcb361 Write human readable version of channel width to CSA event debug log
Signed-off-by: Jouni Malinen <j@w1.fi>
2014-10-26 11:36:14 +02:00
Jouni Malinen
392dfd37e8 nl80211: Store externally managed bridge name in driver status
This makes it easier to figure out from hostapd control interface
whether an interface had been added to a bridge externally at the time
hostapd interface was enabled or if the interface gets added during
hostapd operations.

Signed-off-by: Jouni Malinen <j@w1.fi>
2014-10-26 11:27:31 +02:00
Jouni Malinen
ab93fdebf1 hostapd: Add INTERFACE-ENABLED and INTERFACE-DISABLED events
These can be convenient for upper layer programs to determine if the
hostapd interface gets disabled/re-enabled, e.g., due to rfkill
block/unblock.

Signed-off-by: Jouni Malinen <j@w1.fi>
2014-10-26 10:52:54 +02:00
Ilan Peer
1170239efa P2P: Save group common frequencies in invitation result
Save the group common frequencies when starting a GO due to
an invitation signaling requesting to re-invoke a persistent GO.

To do so, move the code that handles the translation of p2p_channels to
frequency list into a public function so it can be re-used both when GO
Negotiation is done and invitation signaling is done.

Signed-off-by: Ilan Peer <ilan.peer@intel.com>
2014-10-26 01:24:28 +03:00
Ilan Peer
f64d3f0e15 WPS: Add missing device types
Add missing device category and device sub category definitions.

Signed-off-by: Ilan Peer <ilan.peer@intel.com>
2014-10-26 01:24:08 +03:00
Ilan Peer
9bc5cfa338 nl80211: Clear beacon_set when deleting a beacon from deinit_ap()
When a beacon was deleted from the kernel in
wpa_driver_nl80211_deinit_ap(), bss->beacon_set was not cleared so
restarting the AP again was not possible.

Fix this by clearing the variable once the beacon was deleted.

Signed-off-by: Ilan Peer <ilan.peer@intel.com>
2014-10-26 01:24:03 +03:00
Ilan Peer
ea6bf29ea3 nl80211: Add indoor only and GO concurrent flags
Add the following channel flags:

* INDOOR_ONLY: The channel can be used if and only if there is a clear
  assessment that the device is operating in an indoor environment, i.e.,
  it is AC power.

* CONCURRENT_GO: The channel can be used for instantiating a GO if and
  only if there is an additional station interface that is currently
  connected to an AP on the same channel or on the same U-NII band
  (assuming that the AP is an authorized master).

Signed-off-by: Ilan Peer <ilan.peer@intel.com>
2014-10-26 01:23:46 +03:00
Ilan Peer
0a44358055 wpa_supplicant: Use the 'no_ir' notation
Use the 'no_ir' notation instead of the 'passive scan' and
'no_ibss' notations to match the earlier change in nl80211.

Signed-off-by: Ilan Peer <ilan.peer@intel.com>
2014-10-26 01:23:43 +03:00
Constantin Musca
a902d5a64b P2P: Stop driver listen in p2p_state_timeout()
When a P2P timeout occurs and p2p_state_timeout is executed, the
stop_listen function can be called besides setting in_listen to zero in
cases where the driver is still in ROC. That should not really happen in
normal cases, but it is possible for some drivers to extend the ROC
duration. If that happens, the next start_listen request may get
rejected with "P2P: Reject start_listen since p2p_listen_work already
exists".

Signed-off-by: Constantin Musca <constantin.musca@intel.com>
2014-10-25 21:37:18 +03:00
Javier Lopez
01e2231fdc hostapd: Skip some configuration steps for mesh cases
Modify hostapd.c logic to add checks for valid mconf data structure:

- For hostapd_setup_bss we don't need to flush old stations in case
  we're rejoining a mesh network.

- In hostapd_setup_interface_complete, we don't need to setup the
  interface until we join the mesh (same reasoning for
  hostapd_tx_queue_params).

Signed-off-by: Javier Lopez <jlopex@gmail.com>
Signed-off-by: Jason Mobarak <x@jason.mobarak.name>
2014-10-25 17:45:36 +03:00
Bob Copeland
f3e9899e02 mesh: Accept Action frames without BSSID match
[original patch by: Thomas Pedersen <thomas@noack.us>]
Signed-off-by: Bob Copeland <me@bobcopeland.com>
2014-10-25 17:45:35 +03:00
Thomas Pedersen
476e6bb68d mesh: Add mesh mode config option
Modify network mode to support mode number 5 when CONFIG_MESH is
enabled.

Signed-off-by: Javier Lopez <jlopex@gmail.com>
Signed-off-by: Jason Mobarak <x@jason.mobarak.name>
Signed-off-by: Thomas Pedersen <thomas@noack.us>
2014-10-25 17:45:35 +03:00
Bob Copeland
5f92659d88 mesh: Add mesh peering manager
The mesh peering manager establishes and maintains links among
mesh peers, tracking each peer link via a finite state machine.

This implementation supports open mesh peerings.

[assorted fixes from Yu Niiro <yu.niiro@gmail.com>]
[more fixes from Masashi Honma <masashi.honma@gmail.com>]
Signed-off-by: Javier Lopez <jlopex@gmail.com>
Signed-off-by: Javier Cardona <javier@cozybit.com>
Signed-off-by: Ashok Nagarajan <ashok.dragon@gmail.com>
Signed-off-by: Jason Mobarak <x@jason.mobarak.name>
Signed-hostap: Bob Copeland <me@bobcopeland.com>
2014-10-25 17:45:31 +03:00
Thomas Pedersen
8319e3120d mesh: Add mesh mode routines
Add routines to (de)initialize mesh interface data structures and
join and leave mesh networks.

Signed-off-by: Javier Lopez <jlopex@gmail.com>
Signed-off-by: Javier Cardona <javier@cozybit.com>
Signed-off-by: Jason Mobarak <x@jason.mobarak.name>
Signed-off-by: Thomas Pedersen <thomas@noack.us>
2014-10-25 17:43:20 +03:00
Bob Copeland
5551bc9cb2 nl80211: Do not try to change supported rates
For mesh mode to work properly, set supported rates only once.

Signed-off-by: Javier Lopez <jlopex@gmail.com>
Signed-off-by: Javier Cardona <javier@cozybit.com>
Signed-off-by: Jason Mobarak <x@jason.mobarak.name>
Signed-off-by: Bob Copeland <me@bobcopeland.com>
2014-10-25 15:54:57 +03:00
Bob Copeland
7a228b5c3f nl80211: Add STA flag WPA_STA_AUTHENTICATED
This is needed for managing STA entries for mesh use cases.

Signed-off-by: Javier Lopez <jlopex@gmail.com>
Signed-off-by: Javier Cardona <javier@cozybit.com>
Signed-off-by: Jason Mobarak <x@jason.mobarak.name>
Signed-off-by: Bob Copeland <me@bobcopeland.com>
2014-10-25 15:54:47 +03:00
Bob Copeland
7c7e7877fc nl80211: Add plink_action_field to hostapd_sta_add_params
Signed-off-by: Javier Lopez <jlopex@gmail.com>
Signed-off-by: Javier Cardona <javier@cozybit.com>
Signed-off-by: Jason Mobarak <x@jason.mobarak.name>
Signed-off-by: Bob Copeland <me@bobcopeland.com>
2014-10-25 15:54:38 +03:00
Bob Copeland
0d391b03e7 nl80211: Reject deauth/disassoc for mesh interface
sta_info call these to send out the disassoc and deauth frame
which are both not relevent to mesh. So don't send them.

Signed-off-by: Chun-Yeow Yeoh <yeohchunyeow@gmail.com>
Signed-off-by: Javier Lopez <jlopex@gmail.com>
Signed-off-by: Javier Cardona <javier@cozybit.com>
Signed-off-by: Jason Mobarak <x@jason.mobarak.name>
Signed-off-by: Bob Copeland <me@bobcopeland.com>
2014-10-25 13:47:48 +03:00
Bob Copeland
afb0550a39 nl80211: Register to receive mesh frames
Signed-off-by: Javier Lopez <jlopex@gmail.com>
Signed-off-by: Javier Cardona <javier@cozybit.com>
Signed-off-by: Jason Mobarak <x@jason.mobarak.name>
Signed-off-by: Bob Copeland <me@bobcopeland.com>
2014-10-25 13:47:12 +03:00
Jouni Malinen
aed8d4d1ff nl80211: Write channel type in debug log on channel switch event
This makes it easier to understand what kind of channel switch was
indicated by the driver.

Signed-off-by: Jouni Malinen <j@w1.fi>
2014-10-25 11:28:56 +03:00
Jouni Malinen
5de748187e Fix channel switch to disable VHT with HT
If both HT and VHT was enabled on AP and channel switch event from the
driver indicated that HT was disabled, VHT was left enabled. This
resulted in the following channel configuration failing. Fix this by
disabling VHT if HT gets disabled.

Signed-off-by: Jouni Malinen <j@w1.fi>
2014-10-25 11:27:48 +03:00
Eliad Peller
da1080d721 nl80211: Advertise and configure SMPS modes
Advertise static/dynamic SMPS mode support (according to the wiphy
feature bits) and pass the configured smps_mode when starting the AP.

Signed-off-by: Eliad Peller <eliad@wizery.com>
2014-10-24 01:29:08 +03:00
Eliad Peller
8f461b50cf HT: Pass the smps_mode in AP parameters
The driver needs to know what SMPS mode it should use.

Signed-off-by: Eliad Peller <eliad@wizery.com>
2014-10-24 01:27:31 +03:00
Eliad Peller
04ee647d58 HT: Let the driver advertise its supported SMPS modes for AP mode
Add smps_modes field, and let the driver fill it with its supported SMPS
modes (static/dynamic). This will let us start an AP with specific SMPS
mode (e.g., dynamic) that will allow it to reduce its power usage.

Signed-off-by: Eliad Peller <eliad@wizery.com>
2014-10-24 01:25:29 +03:00
Jouni Malinen
4db207518d P2P: Stop TX wait on SD query TX status failure
The previous TX operation could be on another channel if there are
multiple peers with pending SD queries. To avoid failing to send the
following query, stop the last one to allow any Listen channel to be
used for the following query during p2p_find iteration.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2014-10-23 21:52:05 +03:00
Jouni Malinen
44abecbf02 P2P: Limit number of SD retries during find
Commit 7139cf4a4f ('P2P: Decrement
sd_pending_bcast_queries when sd returns success') added support for
retrying P2P SD queries. However, it did this without limiting how many
retries are allowed. This can result in excessive number of retries if a
peer device does not show up on its Listen channel and there is a
pending SD query to it. Limit the maximum number of SD retries to 100
per p2p_find operation for each peer to avoid unlimited retries.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2014-10-23 21:51:48 +03:00
Jouni Malinen
e706b8c8e5 P2P: Iterate through all peers in pending pre-find operation
Commit 7139cf4a4f ('P2P: Decrement
sd_pending_bcast_queries when sd returns success') changed P2P SD
behavior in a way that the P2P search loop ended up in continuing with
the first peer entry until it acknowledged receipt of a pending
broadcast SD request while the previous design went through all peers
once. While it is reasonable to retry SD, getting stuck with the first
peer is not really desirable. Change the p2p_continue_find() loop to
continue from the next peer in each iteration to allow progress through
all peers that have pending operations if any other peer is not
acknowledging frames (e.g., due to not being on Listen channel).

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2014-10-23 21:30:32 +03:00
Chet Lanctot
b41f26845a Add support for offloading key management operations to the driver
This commit introduces a QCA vendor command and event to provide an
option to use extended versions of the nl80211 connect/roam operations
in a way that allows drivers to offload key management operations to the
driver/firmware.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2014-10-23 18:38:50 +03:00
Jouni Malinen
a6b1215769 GAS: Do not reply to P2P SD query from generic GAS/ANQP server
This avoids an issue where a wpa_supplicant build with CONFIG_P2P=y and
CONFIG_HS20=y ended up processing a P2P SD query twice when operating as
a GO and sending out two replies. Only the P2P SD implementation should
reply to P2P SD query in such a case.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2014-10-22 19:21:42 +03:00
Johannes Berg
97752f7930 Revert "nl80211: Do not indicate P2P_DEVICE support by default"
This reverts commit 851b0c5581.

The kernel now has full support for this (and it is turned off
by default for hwsim) so wpa_supplicant should really go back
to autodetecting this so clients don't have to figure out what
to do.

Also add a debug message stating that P2P_DEVICE support is used.

Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2014-10-22 10:54:02 +03:00
Jouni Malinen
ccf79ab256 browser-android: Use execv() directly instead of os_exec()
This allows the URL to be passed as a single argument to the program
instead of getting split into multiple by os_exec(). This makes the
operation more robust for cases where the URL could have been received
from an external source and could potentially add extra arguments to the
command line.

In addition, fix the /system/bin/input execution by using system() for
it instead of execv() through os_exec(). /system/bin/input is a script
that execv() won't be able to run. Since the full command line is
specified, system() can be used for this. The keycode is also changed
from 3 to KEYCODE_HOME to make this work with current Android version.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2014-10-21 23:32:17 +03:00
Jouni Malinen
c94382259d browser-wpadebug: Use execv() directly instead of os_exec()
This allows the URL to be passed as a single argument to the program
instead of getting split into multiple by os_exec(). This makes the
operation more robust for cases where the URL could have been received
from an external source and could potentially add extra arguments to the
command line.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2014-10-21 23:32:17 +03:00
Jouni Malinen
22444bb246 browser-system: Use execv() directly instead of os_exec()
This allows the URL to be passed as a single argument to the program
instead of getting split into multiple by os_exec(). This makes the
operation more robust for cases where the URL could have been received
from an external source and could potentially add extra arguments to the
command line.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2014-10-21 23:32:17 +03:00
Kyeyoon Park
ec8f36afca AP: Add support for BSS load element (STA Count, Channel Utilization)
The new "bss_load_update_period" parameter can be used to configure
hostapd to advertise its BSS Load element in Beacon and Probe Response
frames. This parameter is in the units of BUs (Beacon Units).

When enabled, the STA Count and the Channel Utilization value will be
updated periodically in the BSS Load element. The AAC is set to 0 sinze
explicit admission control is not supported. Channel Utilization is
calculated based on the channel survey information from the driver and
as such, requires a driver that supports providing that information for
the current operating channel.

Signed-off-by: Kyeyoon Park <kyeyoonp@qca.qualcomm.com>
2014-10-21 23:25:48 +03:00
Jouni Malinen
4a6cc86272 Add data test functionality
It is now possible to run hwsim_test like data connectivity test through
wpa_supplicant/hostapd control interface if CONFIG_TESTING_OPTIONS=y is
used for the build. Test functionality is enabled/disabled at runtime
with "DATA_TEST_CONFIG <1/0>". The "DATA_TEST_TX <dst> <src> <tos>"
command can be used to request a test frame to be transmitted.
"DATA-TEST-RX <dst> <src>" event is generated when the test frame is
received.

Signed-off-by: Jouni Malinen <j@w1.fi>
2014-10-19 20:51:45 +03:00
Andrei Otcheretianski
d66873f5cf Do not start CSA flow when CSA is not supported by the driver
Signed-hostap: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
2014-10-19 15:39:59 +03:00
Bob Copeland
a52024c976 nl80211: Add new peer candidate event for mesh
Signed-off-by: Javier Lopez <jlopex@gmail.com>
Signed-off-by: Javier Cardona <javier@cozybit.com>
Signed-off-by: Jason Mobarak <x@jason.mobarak.name>
Signed-off-by: Bob Copeland <me@bobcopeland.com>
2014-10-19 12:58:13 +03:00
Bob Copeland
7e31703e4d nl80211: Add support for sta_add flags_mask
Signed-off-by: Javier Lopez <jlopex@gmail.com>
Signed-off-by: Javier Cardona <javier@cozybit.com>
Signed-off-by: Jason Mobarak <x@jason.mobarak.name>
Signed-off-by: Bob Copeland <me@bobcopeland.com>
2014-10-19 12:58:13 +03:00
Bob Copeland
6c1664f605 nl80211: Add new commands to support mesh interfaces
Create init_mesh, mesh_join, and mesh_leave actions to kernel.

Signed-off-by: Javier Lopez <jlopex@gmail.com>
Signed-off-by: Javier Cardona <javier@cozybit.com>
Signed-off-by: Jason Mobarak <x@jason.mobarak.name>
Signed-off-by: Bob Copeland <me@bobcopeland.com>
2014-10-19 12:58:13 +03:00
Bob Copeland
24bd4e0be5 nl80211: Add driver flag to indicate mesh support
Convert the driver flags variable to u64 since there was no room for
more flags.

Signed-off-by: Javier Lopez <jlopex@gmail.com>
Signed-off-by: Javier Cardona <javier@cozybit.com>
Signed-off-by: Jason Mobarak <x@jason.mobarak.name>
Signed-off-by: Bob Copeland <me@bobcopeland.com>
2014-10-19 12:58:13 +03:00
Bob Copeland
f7072600be Implement RFC 5297 AES-SIV
Add an implementation of Synthetic Initialization Vector (SIV)
Authenticated Encryption Using the Advanced Encryption Standard (AES).

This mode of AES is used to protect peering frames when using
the authenticated mesh peering exchange.

Signed-off-by: Javier Lopez <jlopex@gmail.com>
Signed-off-by: Jason Mobarak <x@jason.mobarak.name>
Signed-off-by: Bob Copeland <me@bobcopeland.com>
2014-10-19 12:43:38 +03:00
Bob Copeland
6293f9ed07 mesh: Parse mesh-related information elements
Add support for parsing mesh id, mesh config, mesh peering,
AMPE and MIC information elements.

Signed-off-by: Bob Copeland <me@bobcopeland.com>
2014-10-19 11:20:05 +03:00
Thomas Pedersen
3e7b032f83 mesh: Add mesh protocol definitions
Signed-off-by: Javier Lopez <jlopex@gmail.com>
Signed-off-by: Jason Mobarak <x@jason.mobarak.name>
Signed-hostap: Thomas Pedersen <thomas@noack.us>
2014-10-19 11:20:05 +03:00
Mikael Kanstrup
a0a5f73e62 P2P: Include passive channels in invitation response
Patch 51e9f22809 added the option
p2p_add_cli_chan to allow P2P GC to connect on passive channels
assuming the GO should know whether allowed to send on these channels.
This patch adds missing cli_channels to invitation response messages
to allow re-connecting to a persistent group as GC on passive
channels.

Signed-off-by: Mikael Kanstrup <mikael.kanstrup@sonymobile.com>
2014-10-18 17:00:57 +03:00
Jouni Malinen
bc26ac50dd SAE: Add support for PMKSA caching on the station side
This makes wpa_supplicant SME create PMKSA cache entries from SAE
authentication and try to use PMKSA caching if an entry is found for the
AP. If the AP rejects the attempt, fall back to SAE authentication is
used.

Signed-off-by: Jouni Malinen <j@w1.fi>
2014-10-18 13:02:02 +03:00
Jouni Malinen
f299117093 SAE: Add support for PMKSA caching on the AP side
This makes hostapd create PMKSA cache entries from SAE authentication
and allow PMKSA caching to be used with the SAE AKM.

Signed-off-by: Jouni Malinen <j@w1.fi>
2014-10-18 13:00:29 +03:00
Jouni Malinen
fcc306e3cc Add Acct-Multi-Session-Id into RADIUS Accounting messages
This allows multiple sessions using the same PMKSA cache entry to be
combined more easily at the server side. Acct-Session-Id is still a
unique identifier for each association, while Acct-Multi-Session-Id will
maintain its value for all associations that use the same PMKSA.

Signed-off-by: Jouni Malinen <j@w1.fi>
2014-10-18 10:38:17 +03:00
Jouni Malinen
aff039fada Remove duplicated Acct-Session-Id from Accounting-Request
Commit 8b24861154 ('Add Acct-Session-Id
into Access-Request messages') added Acct-Session-Id building into the
helper function shared between authentication and accounting messages.
However, it forgot to remove the same code from the generation of
accounting messages and as such, ended up with Accounting-Request
messages containing two copies of this attribute. Fix this by removing
the addition of this attribute from the accounting specific function.

Signed-off-by: Jouni Malinen <j@w1.fi>
2014-10-18 10:35:33 +03:00
Jouni Malinen
0ffe7a5481 RADIUS: Define new attributes from RFC 5580
This adds definition and names for the RADIUS attributes defined in RFC
5580 (Carrying Location Objects in RADIUS and Diameter).

Signed-off-by: Jouni Malinen <j@w1.fi>
2014-10-18 09:30:35 +03:00
Justin Shen
3f7ac05878 WPS: Extend startWhen to 2 if peer AP supports WPS 2.0
Increase EAPOL startWhen to 2 for the case where the AP/GO has
advertised it supports WPS 2.0. This is done to make it less likely for
the EAPOL-Start frame to be sent out since that is only required for WPS
1.0. Not sending it can remove one unnecessary round trip from the EAP
exchange when the AP is going to start with EAP-Request/Identity
immediately based on the Association Request frame.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2014-10-13 12:24:17 +03:00
Jouni Malinen
54a800dd51 netlink: Fix RTM_SETLINK padding at the end of the message
While the kernel seems to have accepted the message to set linkmode and
operstate without the final attribute getting padded to 32-bit length,
it is better to get this cleaned up to match expected format. The double
NLMSG_ALIGN() followed by RTA_LENGTH() did not make much sense here.

Signed-off-by: Jouni Malinen <j@w1.fi>
2014-10-12 19:27:16 +03:00
Jouni Malinen
3eafc494d8 Fix CONFIG_NO_SCAN_PROCESSING=y build
ht_supported() was used but not defined in such a case.

Signed-off-by: Jouni Malinen <j@w1.fi>
2014-10-12 17:02:23 +03:00
Toby Gray
3cea004d3c Make wpa_ctrl_get_remote_ifname declaration conditional.
The definition of wpa_ctrl_get_remote_ifname is conditional on
CONFIG_CTRL_IFACE_UDP. This change makes the header declaration of
this function also conditional on the same define.

Signed-off-by: Toby Gray <toby.gray@realvnc.com>
2014-10-12 16:51:02 +03:00
Toby Gray
f5c649b769 Fix warning about unused parameter if CONFIG_DEBUG_FILE is not defined.
This change adds a cast to void to indicate that the path parameter is
unused when CONFIG_DEBUG_FILE is not defined. This fixes a compiler
warning about unused parameters.

Signed-off-by: Toby Gray <toby.gray@realvnc.com>
2014-10-12 16:49:12 +03:00
Jean Trivelly
4b32f6a5ec P2P: Inform upper layer when WFD-IE field of a P2P device has changed
When WFD IE of a P2P device changes, the field is locally updated in P2P
supplicant but upper layer is not informed about this change.

Signed-off-by: Jean Trivelly <jean.trivelly@intel.com>
2014-10-12 16:34:24 +03:00
Jouni Malinen
07e2de3193 wpa_supplicant: Allow OpenSSL cipherlist string to be configured
The new openssl_cipher configuration parameter can be used to select
which TLS cipher suites are enabled for TLS-based EAP methods when
OpenSSL is used as the TLS library. This parameter can be used both as a
global parameter to set the default for all network blocks and as a
network block parameter to override the default for each network
profile.

Signed-off-by: Jouni Malinen <j@w1.fi>
2014-10-12 11:55:13 +03:00
Jouni Malinen
f8995f8f1c hostapd: Allow OpenSSL cipherlist string to be configured
The new openssl_cipher configuration parameter can be used to select
which TLS cipher suites are enabled when hostapd is used as an EAP
server with OpenSSL as the TLS library.

Signed-off-by: Jouni Malinen <j@w1.fi>
2014-10-12 11:52:05 +03:00
Jouni Malinen
b7328434f7 OpenSSL: Add a mechanism to configure cipher suites
This extends the TLS wrapper code to allow OpenSSL cipherlist string to
be configured. In addition, the default value is now set to
DEFAULT:!EXP:!LOW to ensure cipher suites with low and export encryption
algoriths (40-64 bit keys) do not get enabled in default configuration
regardless of how OpenSSL build was configured.

Signed-off-by: Jouni Malinen <j@w1.fi>
2014-10-12 11:45:21 +03:00
Jouni Malinen
7c0e5b58f9 DFS: Check os_get_random() result
This use does not really need a strong random number, so fall back to
os_random() if a theoretical error case occurs. (CID 72682)

Signed-off-by: Jouni Malinen <j@w1.fi>
2014-10-11 19:43:36 +03:00
Jouni Malinen
24661bbadc AP: Check os_get_random() return value more consistently
While this specific case does not really care what value is used, the
the theoretical error case can be handled more consistently. (CID 72684)

Signed-off-by: Jouni Malinen <j@w1.fi>
2014-10-11 19:43:36 +03:00
Jouni Malinen
8c5dfc79a5 EAP-MSCHAPv2 server: Check ms_funcs results more consistently
This makes the code more consistent by checking the somewhat theoretical
error cases more consistently (CID 72685).

Signed-off-by: Jouni Malinen <j@w1.fi>
2014-10-11 19:43:36 +03:00
Jouni Malinen
08ef4426a7 EAP-IKEv2: Fix the payload parser
The payload lengths were not properly verified and the first check on
there being enough buffer for the header was practically ignored. The
second check for the full payload would catch length issues, but this is
only after the potential read beyond the buffer. (CID 72687)

Signed-off-by: Jouni Malinen <j@w1.fi>
2014-10-11 19:22:30 +03:00
Jouni Malinen
683b408a9e WPS UPnP: Check os_get_random() result more consistently
While the value here would not matter much, make the implementation more
consistent (CID 72692).

Signed-off-by: Jouni Malinen <j@w1.fi>
2014-10-11 19:08:30 +03:00
Jouni Malinen
e7b96ecdb3 TLS client: Make DH parameter parsing easier for static analyzers
The dh_p_len, dh_g_len, and dh_ys_len parameters were validated against
the received message structure, but that did not seem to be done in a
way that some static analyzers would understand this (CID 72699).

Signed-off-by: Jouni Malinen <j@w1.fi>
2014-10-11 19:04:00 +03:00
Jouni Malinen
92b5b371b6 WPS UPnP: Check os_get_random() result
This makes the implementation more consistent (CID 72705).

Signed-off-by: Jouni Malinen <j@w1.fi>
2014-10-11 18:58:17 +03:00
Jouni Malinen
533d7fb7b7 MACsec: Check os_get_random() return value
This makes the MACsec implementation more consistent with rest of
wpa_supplicant. (CID 72677, CID 72695, CID 72701, CID 72709, CID 72711)

Signed-off-by: Jouni Malinen <j@w1.fi>
2014-10-11 18:54:43 +03:00
Jouni Malinen
93da049851 nl80211: Be more consistent with linux_set_iface_flags() result
Check the return value and write a debug message if this operation
failes (CID 74146).

Signed-off-by: Jouni Malinen <j@w1.fi>
2014-10-11 18:43:30 +03:00
Jouni Malinen
6c9f74deaf EAP-PAX server: Remove unused assignment
Signed-off-by: Jouni Malinen <j@w1.fi>
2014-10-11 18:14:42 +03:00
Jouni Malinen
918bd0fe78 EAP-SIM DB: Remove unused assignment
Signed-off-by: Jouni Malinen <j@w1.fi>
2014-10-11 18:13:32 +03:00
Jouni Malinen
6f577c5e45 EAP-FAST server: Remove unused assignment
Commit e8c08c9a36 ('EAP-FAST server: Fix
potential read-after-buffer (by one byte)') changed the while loop
design in a way that does not require the pos variable to be updated
anymore. Remove that unneeded code to clean up static analyzer warnings
about unused assignments.

Signed-off-by: Jouni Malinen <j@w1.fi>
2014-10-11 18:11:14 +03:00
Jouni Malinen
e9471493ef EAP-FAST server: Remove unused write
next_type is not used in case m->check() results in ignoring the packet.

Signed-off-by: Jouni Malinen <j@w1.fi>
2014-10-11 18:10:27 +03:00
Jouni Malinen
58b992489c RADIUS: Remove unused write
There is no need to update the left variable when breaking out from the
loop.

Signed-off-by: Jouni Malinen <j@w1.fi>
2014-10-11 18:06:52 +03:00
Jouni Malinen
4aa01d38f5 IAPP: Avoid warnings on unused write
The hlen and len variables are identical here, but only the hlen was
used in the end. Change this to use the len variable to avoid
unnecessary static analyzer warnings about unused writes.

Signed-off-by: Jouni Malinen <j@w1.fi>
2014-10-11 18:03:38 +03:00
Jouni Malinen
01b3bbfc66 test: Remove driver_test.c
The driver_test.c driver wrapper (-Dtest in wpa_supplicant and
driver=test in hostapd) was previously used for testing without real
Wi-Fi hardware. mac80211_hwsim-based tests have practically replaced all
these needs and there has been no improvements or use for driver_test.c
in a long while. Because of this, there has not really been any effort
to maintain this older test tool and no justification to change this
either. Remove the obsoleted test mechanism to clean up the repository.

Signed-off-by: Jouni Malinen <j@w1.fi>
2014-10-11 17:46:04 +03:00
Jouni Malinen
e41e4f9ee3 Simplify memory allocation/freeing for static analyzers
It looks like the use of sm->wpa == WPA_VERSION_WPA2 in two locations
within the function was a bit too much for clang static analyzer to
understand. Use a separate variable for storing the allocated memory so
that it can be freed unconditionally. The kde variable can point to
either stack memory or temporary allocation, but that is now const
pointer to make the design clearer.

Signed-off-by: Jouni Malinen <j@w1.fi>
2014-10-11 17:29:50 +03:00
Jouni Malinen
f4452cc2b1 Add a workaround to clanc static analyzer warning
dl_list_del() followed by dl_list_add() seemed to confuse clang static
analyzer somehow, so explicitly check for the prev pointer to be
non-NULL to avoid an incorrect warning.

Signed-off-by: Jouni Malinen <j@w1.fi>
2014-10-11 17:18:02 +03:00
Jouni Malinen
3e9fa3be62 WPS UPnP: Make dl_list_first() use easier for static analyzer
The preceding dl_list_len() check guarantees that dl_list_first()
returns an entry and not NULL. However, that seems to be a bit too
difficult path to follow for static analyzers, so add an explicit check
for the dl_list_first() return value to be non-NULL to avoid warnings.

Signed-off-by: Jouni Malinen <j@w1.fi>
2014-10-11 13:45:25 +03:00
Jouni Malinen
e635efb407 P2P: Clean up coding style and indentation level
The multi-line for loop body and incorrect indentation level on the
return statement looked pretty confusing.

Signed-off-by: Jouni Malinen <j@w1.fi>
2014-10-11 12:05:27 +03:00
Jouni Malinen
59d7148ad7 nl80211: Provide subtype and reason code for AP SME drivers
This allows drivers that implement AP SME internally to generate a
Deauthentication or Disassociation frame with the specified reason code.
This was already done with drivers that use hostapd/wpa_supplicant for
AP SME.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2014-10-10 20:05:37 +03:00
Jouni Malinen
9d4ff04af3 Add external EAPOL transmission option for testing purposes
The new ext_eapol_frame_io parameter can be used to configure hostapd
and wpa_supplicant to use control interface for receiving and
transmitting EAPOL frames. This makes it easier to implement automated
test cases for protocol testing. This functionality is included only in
CONFIG_TESTING_OPTIONS=y builds.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2014-10-10 18:40:57 +03:00
Sunil Dutt
61fc90483f P2P: Handle improper WPS termination on GO during group formation
A P2P Client may be able to connect to the GO even if the WPS
provisioning step has not terminated cleanly (e.g., P2P Client does not
send WSC_Done). Such group formation attempt missed the event
notification about started group on the GO and also did not set the
internal state corresponding to the successful group formation.

This commit addresses the missing part by completing GO side group
formation on a successful first data connection if WPS does not complete
cleanly. Also, this commit reorders the STA authorization indications to
ensure that the group formation success notification is given prior to
the first STA connection to handle such scenarios.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2014-10-10 18:40:57 +03:00
Jouni Malinen
51465a0b5c The master branch is now used for v2.4 development
Signed-off-by: Jouni Malinen <j@w1.fi>
2014-10-09 20:36:53 +03:00
Jouni Malinen
724fce8fff Change version information for the 2.3 release
Signed-off-by: Jouni Malinen <j@w1.fi>
2014-10-09 17:41:31 +03:00
Jouni Malinen
2b28ef6ca8 browser-wpadebug: Use more robust mechanism for starting browser
Use os_exec() to run the external browser to avoid undesired command
line processing for control interface event strings. Previously, it
could have been possible for some of the event strings to include
unsanitized data which is not suitable for system() use.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2014-10-09 17:38:25 +03:00
Jouni Malinen
3d8a3ffcf0 browser-android: Use more robust mechanism for starting browser
Use os_exec() to run the external browser to avoid undesired command
line processing for control interface event strings. Previously, it
could have been possible for some of the event strings to include
unsanitized data which is not suitable for system() use.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2014-10-09 17:38:25 +03:00
Jouni Malinen
17dc39a8bc browser-system: Use more robust mechanism for starting browser
Use os_exec() to run the external browser to avoid undesired command
line processing for control interface event strings. Previously, it
could have been possible for some of the event strings to include
unsanitized data which is not suitable for system() use.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2014-10-09 17:38:25 +03:00
Jouni Malinen
89de07a944 Add os_exec() helper to run external programs
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2014-10-09 17:38:25 +03:00
Jouni Malinen
4a274f487a DFS: Allow 80+80 MHz be configured for VHT
This allows cases where neither 80 MHz segment requires DFS to be
configured. DFS CAC operation itself does not yet support 80+80, though,
so if either segment requires DFS, the AP cannot be brought up.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2014-10-09 14:25:55 +03:00
Jouni Malinen
d5fe4e6c18 Reserve QCA vendor specific nl80211 commands 34..49
These are reserved for QCA use.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2014-10-07 20:08:47 +03:00
Jouni Malinen
a256506ddc AES: Extend key wrap implementation to support longer data
This extends the "XOR t" operation in aes_wrap() and aes_unwrap() to
handle up to four octets of the n*h+i value instead of just the least
significant octet. This allows the plaintext be longer than 336 octets
which was the previous limit.

Signed-off-by: Jouni Malinen <j@w1.fi>
2014-10-07 14:57:10 +03:00
Jouni Malinen
eefec1e40b AES: Extend key wrap design to support longer AES keys
This adds kek_len argument to aes_wrap() and aes_unwrap() functions and
allows AES to be initialized with 192 and 256 bit KEK in addition to
the previously supported 128 bit KEK.

The test vectors in test-aes.c are extended to cover all the test
vectors from RFC 3394.

Signed-off-by: Jouni Malinen <j@w1.fi>
2014-10-07 14:57:06 +03:00
Jouni Malinen
98a1571d88 OpenSSL: Clean up one part from the BoringSSL patch
The (int) typecast I used with sk_GENERAL_NAME_num() to complete the
BoringSSL compilation was not really the cleanest way of doing this.
Update that to use stack_index_t variable to avoid this just like the
other sk_*_num() calls.

Signed-off-by: Jouni Malinen <j@w1.fi>
2014-10-07 11:49:20 +03:00
Adam Langley
a8572960a9 Support building with BoringSSL
BoringSSL is Google's cleanup of OpenSSL and an attempt to unify
Chromium, Android and internal codebases around a single OpenSSL.

As part of moving Android to BoringSSL, the wpa_supplicant maintainers
in Android requested that I upstream the change. I've worked to reduce
the size of the patch a lot but I'm afraid that it still contains a
number of #ifdefs.

[1] https://www.imperialviolet.org/2014/06/20/boringssl.html

Signed-off-by: Adam Langley <agl@chromium.org>
2014-10-07 01:18:03 +03:00
Jouni Malinen
a61fcc131a Clean up authenticator PMKSA cache implementation
This makes the implementation somewhat easier to understand.

Signed-off-by: Jouni Malinen <j@w1.fi>
2014-10-04 23:01:08 +03:00
Jouni Malinen
cb129db34c Clear PMKSA cache entry data when freeing them
Avoid leaving the PMK information unnecessarily in memory.

Signed-off-by: Jouni Malinen <j@w1.fi>
2014-10-04 23:01:08 +03:00
Jouni Malinen
8c8d26aada Remove unnecessary PMKSA cache freeing step
_pmksa_cache_free_entry() is a static function that is never called with
entry == NULL, so there is no need to check for that.

Signed-off-by: Jouni Malinen <j@w1.fi>
2014-10-04 23:01:08 +03:00
Jouni Malinen
9c829900bb Fix authenticator OKC fetch from PMKSA cache to avoid infinite loop
If the first entry in the PMKSA cache did not match the station's MAC
address, an infinite loop could be reached in pmksa_cache_get_okc() when
trying to find a PMKSA cache entry for opportunistic key caching cases.
This would only happen if OKC is enabled (okc=1 included in the
configuration file).

Signed-off-by: Jouni Malinen <j@w1.fi>
2014-10-04 23:01:08 +03:00
Jouni Malinen
47ea24c13d Fix PMKSA cache timeout from Session-Timeout in WPA/WPA2 cases
Previously, WPA/WPA2 case ended up using the hardcoded
dot11RSNAConfigPMKLifetime (43200 seconds) for PMKSA cache entries
instead of using the Session-Timeout value from the RADIUS server (if
included in Access-Accept). Store a copy of the Session-Timeout value
and use it instead of the default value so that WPA/WPA2 cases get the
proper timeout similarly to non-WPA/WPA2 cases.

Signed-off-by: Jouni Malinen <j@w1.fi>
2014-10-04 23:01:08 +03:00
Janusz Dziedzic
4ec68377ef wpa_supplicant: Use hostapd_freq_params in assoc_params
Use hostapd_freq_params instead of simple frequency parameter for driver
commands. This is preparation for IBSS configuration to allow use of
HT/VHT in IBSS.

Signed-off-by: Janusz Dziedzic <janusz.dziedzic@tieto.com>
2014-10-04 18:43:42 +03:00
Jouni Malinen
43f02e6ad7 wpa_ctrl: Update wpa_ctrl_recv() documentation for non-block behavior
Commit 4fdc8def88 changed the wpa_ctrl
socket to be be non-blocking, so the comment about wpa_ctrl_recv()
blocking is not valid anymore.

Signed-off-by: Jouni Malinen <j@w1.fi>
2014-10-04 18:32:57 +03:00
Dan Williams
3e0272ca00 nl80211: Re-read MAC address on RTM_NEWLINK
Commit 97279d8d (after hostap-2.0) dropped frame events from foreign
addresses. Unfortunately this commit did not handle the case where the
interface's MAC address might be changed externally, which other
wpa_supplicant code already handled. This causes the driver to reject
any MLME event because the address from the event doesn't match the
stale address in the driver data.

Changing an interface's MAC address requires that the interface be
down, the change made, and then the interface brought back up. This
triggers an RTM_NEWLINK event which driver_nl80211.c can use to
re-read the MAC address of the interface.

Signed-hostap: Dan Williams <dcbw@redhat.com>
2014-10-04 16:41:20 +03:00
Jouni Malinen
5dfbd725a9 nl80211: Add get_bss_ifindex() helper
This can be used to fetch a BSS entry based on interface index.

Signed-off-by: Jouni Malinen <j@w1.fi>
2014-10-04 16:21:03 +03:00
Arik Nemtsov
08d7665c6b TDLS: Use WMM IE for propagating peer WMM capability
Relying on qos qosinfo is not enough, as it can be 0 for WMM enabled
peers that don't support U-APSD. Further, some peers don't even contain
this IE (Google Nexus 5), but do contain the WMM IE during setup.

Signed-off-by: Arik Nemtsov <arikx.nemtsov@intel.com>
2014-10-03 11:52:56 +03:00
Arik Nemtsov
17729b0985 TDLS: Fix concurrent setup test for mac80211 drivers
A recent mac80211 patch ("8f02e6b mac80211: make sure TDLS peer STA
exists during setup") forces the TDLS STA to exist before sending any
mgmt packets. Add the STA before sending a concurrent-setup test packet.

Signed-off-by: Arik Nemtsov <arikx.nemtsov@intel.com>
2014-10-03 11:52:27 +03:00
Arik Nemtsov
984dadc23a TDLS: Set the initiator during tdls_mgmt operations
Some drivers need to know the initiator of a TDLS connection in order
to generate a correct TDLS mgmt packet. It is used to determine
the link identifier IE. Pass this information to the driver.

Signed-off-by: Arik Nemtsov <arikx.nemtsov@intel.com>
2014-10-03 11:52:21 +03:00
Jouni Malinen
01cb5df20c Sync with wireless-testing.git include/uapi/linux/nl80211.h
This brings in nl80211 definitions as of 2014-10-02.

Signed-off-by: Jouni Malinen <j@w1.fi>
2014-10-03 11:39:27 +03:00
Ilan Peer
ca3c6b4da7 nl80211: Fix compatibility with older version of libnl
Commit 97ed9a06df ('nl80211: Remove bridge
FDB entry upon sta_remove()') used nl_sock and nl_socket_* functions
which are not compatible with older versions of libnl. Fix this.

Signed-off-by: Ilan Peer <ilan.peer@intel.com>
2014-10-03 11:34:51 +03:00
Jouni Malinen
d76426c3aa TDLS: Filter AID value properly for VHT peers
IEEE 802.11 standard sends AID in a field that is defined in a bit
strange way to set two MSBs to ones. That is not the real AID and those
extra bits need to be filtered from the value before passing this to the
driver.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2014-10-01 19:58:44 +03:00
Jouni Malinen
1cbdb9d137 Add helper function for generating random MAC addresses with same OUI
random_mac_addr_keep_oui() is similar to random_mac_addr(), but it
maintains the OUI part of the source address.

Signed-off-by: Jouni Malinen <j@w1.fi>
2014-09-30 00:40:23 +03:00
Kyeyoon Park
97ed9a06df nl80211: Remove bridge FDB entry upon sta_remove()
The FDB entry removal ensures that the traffic destined for a
disassociated station's MAC address is no longer forwarded from the
bridge to the BSS.

Signed-off-by: Kyeyoon Park <kyeyoonp@qca.qualcomm.com>
2014-09-29 13:10:13 +03:00
Kyeyoon Park
39323bc16a AP: hostapd_setup_bss() code clean-up
Signed-off-by: Kyeyoon Park <kyeyoonp@qca.qualcomm.com>
2014-09-29 13:10:13 +03:00
Ahmad Masri
1595eb93ae P2P: Add support for 60 GHz social channel
Support 60 GHz band in P2P module by selecting random social channel
from all supported social channels in 2.4 GHz and 60 GHz bands.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2014-09-29 12:01:46 +03:00
Philippe De Swert
375f4a3b5a hostapd: Avoid dead code with P2P not enabled
In case P2P is not enabled the if (dev_addr) is always ignored as
dev_addr will be NULL. As this code is relevant only to P2P, it can be
moved to be the ifdef to avoid static analyzer warnings. (CID 72907)

Signed-off-by: Philippe De Swert <philippe.deswert@jollamobile.com>
2014-09-28 20:47:06 +03:00
Bernhard Walle
a8833b84f4 util: Don't use "\e"
'\e' representing ESC (0x1b) is not C standard, it's an GNU extension.
https://gcc.gnu.org/onlinedocs/gcc/Character-Escapes.html#Character-Escapes

Since the code also compiles on Windows with Microsoft compiler, we
should use '\033' instead.

Note: I didn't try to build the whole wpa_supplicant on Windows, so I
don't know if it still builds (I have no Visual Studio 2005 for a quick
test). I just needed the string conversion routines for the P"" syntax
in both directions.

Signed-off-by: Bernhard Walle <bernhard@bwalle.de>
2014-09-28 19:16:32 +03:00
Stefan Lippers-Hollmann
8c6f4a5a50 ap_config.c: fix typo for "capabilities"
Signed-off-by: Stefan Lippers-Hollmann <s.l-h@gmx.de>
2014-09-28 11:03:48 +03:00
Constantin Musca
7139cf4a4f P2P: Decrement sd_pending_bcast_queries when sd returns success
The sd_pending_bcast_queries variable should be decremented only
in case of success. This way, the supplicant can retry if a service
discovery request fails.

Signed-off-by: Constantin Musca <constantin.musca@intel.com>
2014-09-28 11:03:48 +03:00
Janusz Dziedzic
dbdc9a1d48 nl80211: Fix memory leak on start radar detection error path
Free nlmsg if failing to start radar detection.

Signed-off-by: Janusz Dziedzic <janusz.dziedzic@tieto.com>
2014-09-28 11:03:48 +03:00
Janusz Dziedzic
ed8e005973 hostap: nl80211 use nl80211_put_freq_params
Use nl80211_put_freq_params when it possible. Remove
duplicated code.

Signed-off-by: Janusz Dziedzic <janusz.dziedzic@tieto.com>
2014-09-27 21:47:40 +03:00
Jouni Malinen
4d8fb63799 Add helper function for generating random MAC addresses
Signed-off-by: Jouni Malinen <j@w1.fi>
2014-09-27 19:12:02 +03:00
Jouni Malinen
fee354c74d nl80211: Add command for changing local MAC address
This can be used to allow wpa_supplicant to control local MAC address
for connections.

Signed-off-by: Jouni Malinen <j@w1.fi>
2014-09-27 19:11:24 +03:00
Jouni Malinen
e49cabcf87 P2P: Set timeout when starting GO Negotiation from Probe Req RX
It was possible for the p2p_go_neg_start timeout handler to get called
when there was a pending timeout from an earlier GO Negotiation start.
This could result in that old timeout expiring too early for the newly
started GO Negotiation to complete. Avoid such issues by setting a
sufficiently long timeout here just before triggering the new GO
Negotiation.

Signed-off-by: Jouni Malinen <j@w1.fi>
2014-09-27 16:12:41 +03:00
Jouni Malinen
7549c178ac P2P: Clear pending_listen_freq when starting GO Neg/Invite
Previously, it was possible for the p2p->pending_listen_freq to be left
at non-zero value if Probe Request frame was received from a peer with
which we were waiting to start GO Negotiation/Invite process. That could
result in the following Listen operation getting blocked in some
operation sequences if the peer did not acknowledge the following P2P
Public Action frame.

Signed-off-by: Jouni Malinen <j@w1.fi>
2014-09-27 16:12:41 +03:00
Jouni Malinen
b497a21267 nl80211: Ignore auth/assoc events when testing driver-SME
Previously, extra connect/roam events were ignored when user space SME
was used to avoid confusing double events for association. However,
there was no matching code for ignoring auth/assoc events when using
driver SME. Such events would not normally show up since the driver SME
case would not generated them. However, when testing forced connect
command with force_connect_cmd=1 driver param, these events are
indicated.

Ignore the extra events in testing cases to make the hwsim test cases
match more closely the real code path for driver SME. In addition, this
resolves some test case failures where double association event could
end up causing a failure, e.g., when doing PMKSA caching in
pmksa_cache_oppurtunistic_connect.

Signed-off-by: Jouni Malinen <j@w1.fi>
2014-09-27 16:12:41 +03:00
Sunil Dutt
c53a9bf818 Check for driver's DFS offload capability before handling DFS
This fixes couple of code paths where the WPA_DRIVER_FLAGS_DFS_OFFLOAD
flag was not checked properly and unexpected DFS operations were
initiated (and failed) in case the driver handles all these steps.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2014-09-22 16:50:28 +03:00
Dan Williams
7a4a93b959 dbus: Add SignalPoll() method to report current signal properties
Analogous to the control interface's SIGNAL_POLL request.

Signed-hostap: Dan Williams <dcbw@redhat.com>
2014-09-13 17:21:54 +03:00
Jouni Malinen
df2508d7a8 P2P: Check os_get_random() return value more consistently
In theory, this call could fail, so check the return value before using
the received data. These specific cases would not really care much about
the failures, but this keeps the code more consistent and keeps static
analyzer warnings more useful. (CID 72678, CID 72679, CID 72680,
CID 72683, CID 72689, CID 72698, CID 72703)

Signed-off-by: Jouni Malinen <j@w1.fi>
2014-09-13 16:27:52 +03:00
Jouni Malinen
54461f3e03 RADIUS server: Remove unreachable code
The previous break will already stop the loop, so this unnecessary check
can be removed (CID 72708).

Signed-off-by: Jouni Malinen <j@w1.fi>
2014-09-13 16:22:16 +03:00
Darshan Paranji Sri
e4474c1c20 FT: Fix hostapd with driver-based SME to authorize the STA
The driver-based SME case did not set STA flags properly to the kernel
in the way that hostapd-SME did in ieee802_11.c. This resulted in the FT
protocol case not marking the STA entry authorized. Fix that by handling
the special WLAN_AUTH_FT case in hostapd_notif_assoc() and also add the
forgotten hostapd_set_sta_flags() call to synchronize these flag to the
driver.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2014-09-12 18:46:56 +03:00
Jouni Malinen
0800f9ee6c nl80211: Add roaming policy update using QCA vendor command
This allows updating roaming policy for drivers that select the BSS
internally so that wpa_supplicant (based on bssid parameter
configuration) and the driver remain in sync.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2014-09-11 15:59:42 +03:00
Jouni Malinen
0ef023e478 Add support for driver command to update roaming policy
The network block bssid parameter can be used to force a specific BSS to
be used for a connection. It is also possible to modify this parameter
during an association. Previously, that did not result in any
notification to the driver which was somewhat problematic with drivers
that take care of BSS selection. Add a new mechanism to allow
wpa_supplicant to provide a driver update if the bssid parameter change
for the current connection modifies roaming policy (roaming
allowed/disallowed within ESS).

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2014-09-11 15:59:42 +03:00
Jouni Malinen
0cd9846c63 nl80211: Print debug info on STA flag changes
This makes it easier to follow how kernel STA flags are managed.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2014-09-11 11:25:04 +03:00
Jouni Malinen
17e2091279 P2P: Fix radio work issue with wait-for-peer GO Negotiation
If a TX status event and RX event for a GO Negotiation frame gets
delayed long enough to miss the initial wait, it was possible for
reception of a GO Negotiation Response frame with status 1 to try to
initiate a new p2p-listen work item to wait for the peer to become ready
while a previous p2p-listen was already in progress due to that earlier
timeout while waiting for peer. This would result in the new
start_listen request getting rejected ("P2P: Reject start_listen since
p2p_listen_work already exists") and the negotiation not proceeding.

Work around this by using P2P_WAIT_PEER_CONNECT state instead of
P2P_WAIT_PEER_IDLE if P2P_CONNECT_LISTEN state has already been entered
when processing this special GO Negotiation Response status=1 case. This
can avoid double-scheduling of p2p-listen and as such, completion of the
GO negotiation even if the driver event or peer response are not
received in time (the response is supposed to be there within 100 ms per
spec, but there are number of deployed devices that do not really meet
this requirement).

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2014-09-09 18:00:42 +03:00
Jouni Malinen
b08d5fa793 WPS: Set EAPOL workarounds dynamically based on association
Previously, the shorter startWhen value was used based on build
parameters (i.e., if WPS was enabled). This is not really ideal and the
knowledge of WPS use can be provided to the EAPOL state machine to allow
this (and similar WPS workarounds) to be done only when the association
is for the purpose of WPS.

Reduce the default startWhen value from 3 to 2 seconds for non-WPS case
since WPS builds have likely received most testing for the past years
with the 1 second value and there is no strong justification for forcing
the longer 3 second wait should a frame be lost or something else
require the EAPOL-Start to initiate operation after a connection.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2014-09-08 17:16:04 +03:00
Jouni Malinen
8511a0f67b WPS: Extend internal entropy pool help for key/snonce derivation
The internal entropy pool was previously used to prevent 4-way handshake
in AP mode from completing before sufficient entropy was available to
allow secure keys to be generated. This commit extends that workaround
for boards that do not provide secure OS level PRNG (e.g., /dev/urandom
does not get enough entropy) for the most critical WPS operations by
rejecting AP-as-enrollee case (use of AP PIN to learn/modify AP
configuration) and new PSK/passphrase generation. This does not have any
effect on devices that have an appropriately working OS level PRNG
(e.g., /dev/random and /dev/urandom on Linux).

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2014-09-08 12:54:18 +03:00
Eduardo Abinader
3ee18569f5 nl80211: Register eloop after hs20 action frame
Even when hs20 action frame is unable to be registered,
for whatever reason, it should be possible to register
event handle for received driver messages. This patch also
avoids a segmentation fault, when p2p and hs20 were enabled
and GO NEG was unable to create p2p iface, the destroy eloop
was crashing by reading an invalid handle.

Signed-off-by: Eduardo Abinader <eduardo.abinader@openbossa.org>
2014-09-07 19:22:49 +03:00
Masashi Honma
5c61d214ad openssl: Fix memory leak in openssl ec deinit
Signed-off-by: Masashi Honma <masashi.honma@gmail.com>
2014-09-07 19:14:18 +03:00
Jouni Malinen
3a413e0ed8 RADIUS client: Check getsockname() return value
In theory, this function could fail, so check the return value before
printing out the RADIUS local address debug message (CID 72700).

Signed-off-by: Jouni Malinen <j@w1.fi>
2014-09-07 18:35:46 +03:00
Jouni Malinen
9c196f7703 HTTP: Fix OCSP status check
Due to a missing curly brackets, the OCSP status checking was not
working in the expected way. Instead of allowing optional-OCSP
configuration to accept connection when OCSP response was ready, all
such cases were marked as hard failures. In addition, the debug prints
were not necessarily accurate for the mandatory-OCSP-but-no-response
case (CID 72694, CID 72704).

Signed-off-by: Jouni Malinen <j@w1.fi>
2014-09-07 18:30:58 +03:00
Jouni Malinen
c9cd78e5a1 RADIUS server: Fix IPv6 radiusAuthClientAddress mask
Incorrect buffer was used when writing the IPv6 mask for RADIUS server
MIB information (CID 72707).

Signed-off-by: Jouni Malinen <j@w1.fi>
2014-09-07 18:25:04 +03:00
Jouni Malinen
6473e80ea4 EAP-PAX server: Add explicit CID length limit
Instead of using implicit limit based on 16-bit unsigned integer having
a maximum value of 65535, limit the maximum length of a CID explicitly
to 1500 bytes. This will hopefully help in reducing false warnings from
static analyzers (CID 72712).

Signed-off-by: Jouni Malinen <j@w1.fi>
2014-09-07 17:10:33 +03:00
Jouni Malinen
6a6566c7af Remove unnecessarily shadowed local variable
The same local X509 *cert variable can be used for both the X509_dup()
calls.

Signed-off-by: Jouni Malinen <j@w1.fi>
2014-09-07 16:40:33 +03:00
Sunil Dutt
e47abdb9db TDLS: Decline Setup Request with status code 37 if BSSID does not match
TDLS Setup Request frame has to be rejected with status code 37 ("The
request has been declined"), if the BSSID in the received Link
Identifier does not match the current BSSID per IEEE Std 802.11-2012,
10.22.4 ('TDLS direct-link establishment') step (b). The previously used
status code 7 ('Not in same BSS') is described to used only when
processing TPK Handshake Message 2 in TDLS Setup Response frame.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2014-09-02 18:06:58 +03:00
Mahesh A Saptasagar
ce2002acca TDLS: Add RSN and Timeout interval IEs in TDLS Discovery Response frame
If RSN is enabled, add RSN and Timeout interval elements in TDLS
Discovery Response frames.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2014-09-02 17:11:42 +03:00
Jouni Malinen
f2e9083549 nl80211: Add more RTM_NEWLINK/DELLINK debug messages
This makes it easier to figure out what operations are generating each
RTM_DELLINK message.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2014-09-01 16:18:01 +03:00
Jouni Malinen
728ff2f469 nl80211: Fix RTM_DELLINK processing for bridge events
When a netdev is removed from a bridge, RTM_DELLINK message is received
with ifname (IFLA_IFNAME) pointing to the main netdev event though that
netdev is not deleted. This was causing issues with P2P GO interface
getting disabled when the netdev was removed from a bridge. Fix this by
filtering RTM_DELLINK events that are related to the bridge when
indicating interface status changes.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2014-09-01 16:14:07 +03:00
Jouni Malinen
04a258e7c5 hostapd: Check that EVENT_ASSOC data is present before using it
While hostapd should not really receive the EVENT_ASSOC message for
IBSS, driver_nl80211.c could potentially generate that if something
external forces the interface into IBSS mode and the IBSS case does not
provide the struct assoc_info data. Avoid the potential NULL pointer
dereference by explicitly verifying for the event data to be present.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2014-08-26 17:23:02 +03:00
Avinash Patil
b8d87ed296 nl80211: Disable Probe Request reporting for static AP during deinit
Disable Probe Request reporting for statically created AP interfaces
during de-initialization. We will enable it again while starting AP
operations.

Signed-off-by: Avinash Patil <avinashapatil@gmail.com>
2014-08-10 11:22:30 +03:00
Avinash Patil
bf144cf649 nl80211: Do not change iftype for static AP interface
Some devices have limitations which do not allow changing virtual
interface mode from AP to station or vice versa. To work around this,
check if such AP interface is not dynamic. If such an interface is
enumarated, just set ifmode to AP and avoid setting nlmode to default
station mode on deinit.

Signed-off-by: Avinash Patil <avinashapatil@gmail.com>
2014-08-10 11:19:11 +03:00
Jean-Marie Lemetayer
61157afb1c wext: Add signal_poll callback
Add a basic implementation of a signal_poll callback for wext drivers.

Signed-off-by: Jean-Marie Lemetayer <jeanmarie.lemetayer@gmail.com>
2014-08-10 11:07:05 +03:00
Jouni Malinen
6c460eaf7e Add RSN cipher/AKM suite attributes into RADIUS messages
This adds hostapd support for the new WLAN-Pairwise-Cipher,
WLAN-Group-Cipher, WLAN-AKM-Suite, and WLAN-Group-Mgmt-Pairwise-Cipher
attributes defined in RFC 7268. These attributes are added to RADIUS
messages when the station negotiates use of WPA/RSN.

Signed-off-by: Jouni Malinen <j@w1.fi>
2014-07-31 19:55:29 +03:00
Jouni Malinen
cdffd72173 Add WLAN-HESSID into RADIUS messages
This adds hostapd support for the new WLAN-HESSID attribute defined in
RFC 7268. This attribute contains the HESSID and it is added whenever
Interworking is enabled and HESSID is configured.

Signed-off-by: Jouni Malinen <j@w1.fi>
2014-07-31 19:55:29 +03:00
Jouni Malinen
69002fb0a8 Add Mobility-Domain-Id into RADIUS messages
This adds hostapd support for the new Mobility-Domain-Id attribute
defined in RFC 7268. This attribute contains the mobility domain id and
it is added whenever the station negotiates use of FT.

Signed-off-by: Jouni Malinen <j@w1.fi>
2014-07-31 19:55:29 +03:00
Elliott Hughes
ec5357323c Android: Always #include <sys/...>, not <linux/...>
Signed-off-by: Dmitry Shmidt <dimitrysh@google.com>
2014-07-31 16:59:23 +03:00
Jouni Malinen
e8c08c9a36 EAP-FAST server: Fix potential read-after-buffer (by one byte)
The special PAC_OPAQUE_TYPE_PAD case did not skip incrementing of the
pos pointer and could result in one octet read-after-buffer when parsing
the PAC-Opaque data.

Signed-off-by: Jouni Malinen <j@w1.fi>
2014-07-26 21:14:05 +03:00
Jouni Malinen
27a725cf74 EAP: Do not allow fast session resumption with different network block
This forces EAP peer implementation to drop any possible fast resumption
data if the network block for the current connection is not the same as
the one used for the previous one. This allows different network blocks
to be used with non-matching parameters to enforce different rules even
if the same authentication server is used. For example, this allows
different CA trust rules to be enforced with different ca_cert
parameters which can prevent EAP-TTLS Phase 2 from being used based on
TLS session resumption.

Signed-off-by: Jouni Malinen <j@w1.fi>
2014-07-26 19:39:13 +03:00
Jouni Malinen
905c7223b1 Add wpa_msg_global_ctrl()
This is similar to wpa_msg_global() in the same way as wpa_msg_ctrl() is
to wpa_msg(). In other words, wpa_msg_global_ctrl() is used to send
global control interface events without printing them into the debug
log.

Signed-off-by: Jouni Malinen <j@w1.fi>
2014-07-26 13:04:03 +03:00
Jouni Malinen
1f1fe195cd EAP-pwd: Clear identity string and temporary buffer explicitly
Use an explicit memset call to clear any configuration parameter and
dynamic data that contains private information like keys or identity.
This brings in an additional layer of protection by reducing the length
of time this type of private data is kept in memory.

Signed-off-by: Jouni Malinen <j@w1.fi>
2014-07-24 20:12:57 +03:00
Florent Daigniere
f119d66942 EAP-pwd: Verify BN_rand_range return code
This makes the EAP-pwd server and peer implementations more robust
should OpenSSL fail to derive random number for some reason. While this
is unlikely to happen in practice, the implementation better be prepared
for this should something unexpected ever happen. See
http://jbp.io/2014/01/16/openssl-rand-api/#review-of-randbytes-callers
for more details.

Signed-off-by: Florent Daigniere <nextgens@freenetproject.org>
2014-07-24 19:42:44 +03:00
Florent Daigniere
5197f0335c EAP-pwd: Use os_memcmp_const() for hash comparisons
This makes the implementation less likely to provide useful timing
information to potential attackers from comparisons of information
received from a remote device and private material known only by the
authorized devices.

Signed-off-by: Florent Daigniere <nextgens@freenetproject.org>
2014-07-24 19:39:44 +03:00
Florent Daigniere
26c10f797c OpenSSL: Use EC_POINT_clear_free instead of EC_POINT_free
This changes OpenSSL calls to explicitly clear the EC_POINT memory
allocations when freeing them. This adds an extra layer of security by
avoiding leaving potentially private keys into local memory after they
are not needed anymore. While some of these variables are not really
private (e.g., they are sent in clear anyway), the extra cost of
clearing them is not significant and it is simpler to just clear these
explicitly rather than review each possible code path to confirm where
this does not help.

Signed-off-by: Florent Daigniere <nextgens@freenetproject.org>
2014-07-24 19:35:07 +03:00
Florent Daigniere
3248071dc3 OpenSSL: Use BN_clear_free instead of BN_free
This changes OpenSSL calls to explicitly clear the bignum memory
allocations when freeing them. This adds an extra layer of security by
avoiding leaving potentially private keys into local memory after they
are not needed anymore. While some of these variables are not really
private (e.g., they are sent in clear anyway), the extra cost of
clearing them is not significant and it is simpler to just clear these
explicitly rather than review each possible code path to confirm where
this does not help.

Signed-off-by: Florent Daigniere <nextgens@freenetproject.org>
2014-07-24 19:28:39 +03:00
Dmitry Shmidt
870dfe9932 EAP-TTLS: Remove FreeRADIUS workaround for EAP-TTLS/MSCHAPv2
FreeRADIUS releases before 1.1.4 did not send MS-CHAP2-Success in
EAP-TTLS/MSCHAPv2. A wpa_supplicant workaround for that was added in
2005 and it has been enabled by default to avoid interoperability
issues. This could be disabled with all other EAP workarounds
(eap_workaround=0). However, that will disable some workarounds that are
still needed with number of authentication servers.

Old FreeRADIUS versions should not be in use anymore, so it makes sense
to remove this EAP-TTLS/MSCHAPv2 workaround completely to get more
complete validation of server behavior. This allows MSCHAPv2 to verify
that the server knows the password instead of relying only on the TLS
certificate validation.

Signed-off-by: Dmitry Shmidt <dimitrysh@google.com>
2014-07-20 10:20:24 +03:00
Cedric IZOARD
6d00ab0430 nl80211: Ensure nl_preq unregistration on driver deinit
When driver interface is destroyed (via wpa_driver_nl80211_deinit) the
"preq" nl socket isn't always deleted but the callback struct associated
is. After the interface is destroyed we may still get event on the
socket but as the callback has been freed this will cause wpa_supplicant
to crash.

This patch ensures that the "preq" socket is destroyed when destroying
the interface.

Signed-off-by: Cedric IZOARD <cedricx.izoard@intel.com>
2014-07-08 16:01:43 +03:00
Jouni Malinen
71a0e395b9 P2P: Make unrecognized vendor elements available in P2P_PEER
This allows external programs to use vendor specific information from
P2P peers without wpa_supplicant having to be able to parse and
understand all such vendor specific elements.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2014-07-08 15:57:30 +03:00
Jouni Malinen
86bd36f0d5 Add generic mechanism for adding vendor elements into frames
This adds following new control interface commands to allow arbitrary
vendor elements to be added into number of frames:

VENDOR_ELEM_ADD <frame id> <hexdump of elem(s)>
VENDOR_ELEM_GET <frame id>
VENDOR_ELEM_REMOVE <frame id> <hexdump of elem(s)>
VENDOR_ELEM_REMOVE <frame id> *

The following frames are supported in this commit (additional frames can
be added in the future):

0 = Probe Request frame in P2P device discovery
1 = Probe Response frame from P2P Device role
2 = Probe Response frame from P2P GO
3 = Beacon frame from P2P GO
4 = PD Req
5 = PD Resp
6 = GO Neg Req
7 = GO Neg Resp
8 = GO Neg Conf
9 = Invitation Request
10 = Invitation Response
11 = P2P Association Request
12 = P2P Association Response

One or more vendor element can be added/removed with the commands. The
hexdump of the element(s) needs to contain the full element (id, len,
payload) and the buffer needs to pass IE parsing requirements to be
accepted.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2014-07-07 12:25:09 +03:00
Jouni Malinen
c0e46bb7d4 DFS: Remove dead assignment
set_dfs_state() return value is not currently checked anywhere, so
remove the dead assignment to avoid static analyzer complaints.

Signed-off-by: Jouni Malinen <j@w1.fi>
2014-07-03 00:51:47 +03:00
Jouni Malinen
18389abcca WPS: Clear keys/PINs explicitly
Use an explicit memset call to clear any configuration parameter and
dynamic data that contains private information like keys or identity.
This brings in an additional layer of protection by reducing the length
of time this type of private data is kept in memory.

Signed-off-by: Jouni Malinen <j@w1.fi>
2014-07-02 12:52:08 +03:00
Jouni Malinen
b7175b4d02 Clear hostapd configuration keys explicitly
Use an explicit memset call to clear any hostapd configuration parameter
that contains private information like keys or identity. This brings in
an additional layer of protection by reducing the length of time this
type of private data is kept in memory.

Signed-off-by: Jouni Malinen <j@w1.fi>
2014-07-02 12:38:48 +03:00
Jouni Malinen
d1ecca6c15 HS 2.0 R2: Clear hs20-osu-client configuration keys explicitly
Use an explicit memset call to clear any hs20-osu-client configuration
parameter that contains private information like keys or identity. This
brings in an additional layer of protection by reducing the length of
time this type of private data is kept in memory.

Signed-off-by: Jouni Malinen <j@w1.fi>
2014-07-02 12:38:48 +03:00
Jouni Malinen
0a13e06bdb EAP server: Clear keying material on deinit
Reduce the amount of time keying material (MSK, EMSK, temporary private
data) remains in memory in EAP methods. This provides additional
protection should there be any issues that could expose process memory
to external observers.

Signed-off-by: Jouni Malinen <j@w1.fi>
2014-07-02 12:38:48 +03:00
Jouni Malinen
f534ee0804 EAP peer: Clear keying material on deinit
Reduce the amount of time keying material (MSK, EMSK, temporary private
data) remains in memory in EAP methods. This provides additional
protection should there be any issues that could expose process memory
to external observers.

Signed-off-by: Jouni Malinen <j@w1.fi>
2014-07-02 12:38:48 +03:00
Jouni Malinen
19c48da06b Clear wpa_supplicant configuration keys explicitly
Use an explicit memset call to clear any wpa_supplicant configuration
parameter that contains private information like keys or identity. This
brings in an additional layer of protection by reducing the length of
time this type of private data is kept in memory.

Signed-off-by: Jouni Malinen <j@w1.fi>
2014-07-02 12:38:48 +03:00
Jouni Malinen
28bfa29117 EAP-AKA: Remove unnecessary dead increment
The pos pointer is not used after this now nor in future plans, so no
need to increment the value. This remove a static analyzer warning about
dead increment.

Signed-off-by: Jouni Malinen <j@w1.fi>
2014-07-02 12:38:48 +03:00
Jouni Malinen
62493dff1b EAP-GPSK: Avoid dead increment by checking pos pointer
Instead of using the pre-calculated length of the buffer, determine the
length of used data based on the pos pointer. This avoids a static
analyzer warning about dead increment.

Signed-off-by: Jouni Malinen <j@w1.fi>
2014-07-02 12:38:48 +03:00
Jouni Malinen
164a453f9b FT: Debug print extra response data
This shows any extra data from FT response and also avoids a static
analyzer warning on dead increment.

Signed-off-by: Jouni Malinen <j@w1.fi>
2014-07-02 12:38:48 +03:00
Jouni Malinen
70bfc77161 PCSC: Debug print extra response data
This shows any extra data from USIM response and also avoids a static
analyzer warning on dead increment.

Signed-off-by: Jouni Malinen <j@w1.fi>
2014-07-02 12:38:48 +03:00
Jouni Malinen
0233dcac5b SAE: Use os_memcmp_const() for hash/password comparisons
This makes the implementation less likely to provide useful timing
information to potential attackers from comparisons of information
received from a remote device and private material known only by the
authorized devices.

Signed-off-by: Jouni Malinen <j@w1.fi>
2014-07-02 12:38:48 +03:00
Jouni Malinen
34ef46ce54 WEP shared key: Use os_memcmp_const() for hash/password comparisons
This makes the implementation less likely to provide useful timing
information to potential attackers from comparisons of information
received from a remote device and private material known only by the
authorized devices.

Signed-off-by: Jouni Malinen <j@w1.fi>
2014-07-02 12:38:48 +03:00
Jouni Malinen
3e4b77c9bd EAP-GTC: Use os_memcmp_const() for hash/password comparisons
This makes the implementation less likely to provide useful timing
information to potential attackers from comparisons of information
received from a remote device and private material known only by the
authorized devices.

Signed-off-by: Jouni Malinen <j@w1.fi>
2014-07-02 12:38:48 +03:00
Jouni Malinen
a6eae3f7a1 EAP-MSCHAPv2: Use os_memcmp_const() for hash/password comparisons
This makes the implementation less likely to provide useful timing
information to potential attackers from comparisons of information
received from a remote device and private material known only by the
authorized devices.

Signed-off-by: Jouni Malinen <j@w1.fi>
2014-07-02 12:38:48 +03:00
Jouni Malinen
30411b351c EAP-TTLS: Use os_memcmp_const() for hash/password comparisons
This makes the implementation less likely to provide useful timing
information to potential attackers from comparisons of information
received from a remote device and private material known only by the
authorized devices.

Signed-off-by: Jouni Malinen <j@w1.fi>
2014-07-02 12:38:47 +03:00
Jouni Malinen
a564d9ca36 EAP-MD5: Use os_memcmp_const() for hash/password comparisons
This makes the implementation less likely to provide useful timing
information to potential attackers from comparisons of information
received from a remote device and private material known only by the
authorized devices.

Signed-off-by: Jouni Malinen <j@w1.fi>
2014-07-02 12:38:47 +03:00
Jouni Malinen
4685482552 EAP-PSK: Use os_memcmp_const() for hash/password comparisons
This makes the implementation less likely to provide useful timing
information to potential attackers from comparisons of information
received from a remote device and private material known only by the
authorized devices.

Signed-off-by: Jouni Malinen <j@w1.fi>
2014-07-02 12:38:47 +03:00
Jouni Malinen
cba0f8698b EAP-PEAP: Use os_memcmp_const() for hash/password comparisons
This makes the implementation less likely to provide useful timing
information to potential attackers from comparisons of information
received from a remote device and private material known only by the
authorized devices.

Signed-off-by: Jouni Malinen <j@w1.fi>
2014-07-02 12:38:47 +03:00
Jouni Malinen
7b1e745870 EAP-LEAP: Use os_memcmp_const() for hash/password comparisons
This makes the implementation less likely to provide useful timing
information to potential attackers from comparisons of information
received from a remote device and private material known only by the
authorized devices.

Signed-off-by: Jouni Malinen <j@w1.fi>
2014-07-02 12:38:47 +03:00
Jouni Malinen
8f92826b15 EAP-GPSK: Use os_memcmp_const() for hash/password comparisons
This makes the implementation less likely to provide useful timing
information to potential attackers from comparisons of information
received from a remote device and private material known only by the
authorized devices.

Signed-off-by: Jouni Malinen <j@w1.fi>
2014-07-02 12:38:47 +03:00
Jouni Malinen
e1550d4be8 EAP-PAX: Use os_memcmp_const() for hash/password comparisons
This makes the implementation less likely to provide useful timing
information to potential attackers from comparisons of information
received from a remote device and private material known only by the
authorized devices.

Signed-off-by: Jouni Malinen <j@w1.fi>
2014-07-02 12:38:47 +03:00
Jouni Malinen
c434503f5e EAP-FAST: Use os_memcmp_const() for hash/password comparisons
This makes the implementation less likely to provide useful timing
information to potential attackers from comparisons of information
received from a remote device and private material known only by the
authorized devices.

Signed-off-by: Jouni Malinen <j@w1.fi>
2014-07-02 12:38:47 +03:00
Jouni Malinen
dddf7bbd4e EAP-EKE: Use os_memcmp_const() for hash/password comparisons
This makes the implementation less likely to provide useful timing
information to potential attackers from comparisons of information
received from a remote device and private material known only by the
authorized devices.

Signed-off-by: Jouni Malinen <j@w1.fi>
2014-07-02 12:38:47 +03:00
Jouni Malinen
dfb5608139 EAP-SAKE: Use os_memcmp_const() for hash/password comparisons
This makes the implementation less likely to provide useful timing
information to potential attackers from comparisons of information
received from a remote device and private material known only by the
authorized devices.

Signed-off-by: Jouni Malinen <j@w1.fi>
2014-07-02 12:38:47 +03:00
Jouni Malinen
05c79d6acd EAP-SIM/AKA: Use os_memcmp_const() for hash/password comparisons
This makes the implementation less likely to provide useful timing
information to potential attackers from comparisons of information
received from a remote device and private material known only by the
authorized devices.

Signed-off-by: Jouni Malinen <j@w1.fi>
2014-07-02 12:38:47 +03:00
Jouni Malinen
675ddad1c2 EAP-IKEv2: Use os_memcmp_const() for hash/password comparisons
This makes the implementation less likely to provide useful timing
information to potential attackers from comparisons of information
received from a remote device and private material known only by the
authorized devices.

Signed-off-by: Jouni Malinen <j@w1.fi>
2014-07-02 12:38:47 +03:00
Jouni Malinen
2049a3c874 TLS: Use os_memcmp_const() for hash/password comparisons
This makes the implementation less likely to provide useful timing
information to potential attackers from comparisons of information
received from a remote device and private material known only by the
authorized devices.

Signed-off-by: Jouni Malinen <j@w1.fi>
2014-07-02 12:38:47 +03:00
Jouni Malinen
a79aea531e Milenage: Use os_memcmp_const() for hash/password comparisons
This makes the implementation less likely to provide useful timing
information to potential attackers from comparisons of information
received from a remote device and private material known only by the
authorized devices.

Signed-off-by: Jouni Malinen <j@w1.fi>
2014-07-02 12:38:47 +03:00
Jouni Malinen
05f916eeed AES-GCM: Use os_memcmp_const() for hash/password comparisons
This makes the implementation less likely to provide useful timing
information to potential attackers from comparisons of information
received from a remote device and private material known only by the
authorized devices.

Signed-off-by: Jouni Malinen <j@w1.fi>
2014-07-02 12:38:47 +03:00
Jouni Malinen
87a5c93bec AES-CCM: Use os_memcmp_const() for hash/password comparisons
This makes the implementation less likely to provide useful timing
information to potential attackers from comparisons of information
received from a remote device and private material known only by the
authorized devices.

Signed-off-by: Jouni Malinen <j@w1.fi>
2014-07-02 12:38:47 +03:00
Jouni Malinen
7c24f53c88 EAPOL supplicant: Use os_memcmp_const() for hash/password comparisons
This makes the implementation less likely to provide useful timing
information to potential attackers from comparisons of information
received from a remote device and private material known only by the
authorized devices.

Signed-off-by: Jouni Malinen <j@w1.fi>
2014-07-02 12:38:47 +03:00
Jouni Malinen
870834a19b RSN authenticator: Use os_memcmp_const() for hash/password comparisons
This makes the implementation less likely to provide useful timing
information to potential attackers from comparisons of information
received from a remote device and private material known only by the
authorized devices.

Signed-off-by: Jouni Malinen <j@w1.fi>
2014-07-02 12:38:47 +03:00
Jouni Malinen
0d15b69f0a RSN supplicant: Use os_memcmp_const() for hash/password comparisons
This makes the implementation less likely to provide useful timing
information to potential attackers from comparisons of information
received from a remote device and private material known only by the
authorized devices.

Signed-off-by: Jouni Malinen <j@w1.fi>
2014-07-02 12:38:47 +03:00
Jouni Malinen
72619ce61b MACsec: Use os_memcmp_const() for hash/password comparisons
This makes the implementation less likely to provide useful timing
information to potential attackers from comparisons of information
received from a remote device and private material known only by the
authorized devices.

Signed-off-by: Jouni Malinen <j@w1.fi>
2014-07-02 12:38:47 +03:00
Jouni Malinen
c2371953f8 RADIUS: Use os_memcmp_const() for hash/password comparisons
This makes the implementation less likely to provide useful timing
information to potential attackers from comparisons of information
received from a remote device and private material known only by the
authorized devices.

Signed-off-by: Jouni Malinen <j@w1.fi>
2014-07-02 12:38:47 +03:00
Jouni Malinen
ce9c9bcc38 WPS: Use os_memcmp_const() for hash/password comparisons
This makes the implementation less likely to provide useful timing
information to potential attackers from comparisons of information
received from a remote device and private material known only by the
authorized devices.

Signed-off-by: Jouni Malinen <j@w1.fi>
2014-07-02 12:38:47 +03:00
Jouni Malinen
afc3c8b07f Add constant time memory comparison function os_memcmp_const
This function is meant for comparing passwords or hash values where
difference in execution time could provide external observer information
about the location of the difference in the memory buffers. The return
value does not behave like os_memcmp(), i.e., os_memcmp_const() cannot
be used to sort items into a defined order. Unlike os_memcmp(),
execution time of os_memcmp_const() does not depend on the contents of
the compared memory buffers, but only on the total compared length.

Signed-off-by: Jouni Malinen <j@w1.fi>
2014-07-02 12:38:47 +03:00
Jouni Malinen
ee352f1e5a EAP-pwd: Add explicit total length limit
Instead of using implicit limit based on 16-bit unsigned integer having
a maximum value of 65535, limit the maximum length of a fragmented
EAP-pwd message explicitly to 15000 bytes. None of the supported groups
use longer messages, so it is fine to reject any longer message without
even trying to reassemble it. This will hopefully also help in reducing
false warnings from static analyzers (CID 68124).

Signed-off-by: Jouni Malinen <j@w1.fi>
2014-07-02 12:38:47 +03:00
Jouni Malinen
b2b8a4cb10 EAP-SIM/AKA: Pass EAP type as argument to eap_sim_msg_finish()
This makes it easier for static analyzers to figure out which code paths
are possible within eap_sim_msg_finish() for EAP-SIM. This will
hopefully avoid some false warnings (CID 68110, CID 68113, CID 68114).

Signed-off-by: Jouni Malinen <j@w1.fi>
2014-07-02 12:38:47 +03:00
Jouni Malinen
f107d00cf6 PeerKey: Clean up EAPOL-Key Key Data processing
This extends the earlier commit e6270129f6
('Clean up EAPOL-Key Key Data processing') design to be used with
PeerKey EAPOL-key processing as well. This avoids false warnings from
static analyzer (CID 62860, CID 62861, CID 62862).

Signed-off-by: Jouni Malinen <j@w1.fi>
2014-07-02 12:38:46 +03:00
Tomasz Bursztyka
36716eef89 P2P: Add a utility function to run a method on every known peer
This will be useful in wpa_supplicant part to signal if a peer got its
group changed.

Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
2014-06-29 17:27:27 +03:00
Tomasz Bursztyka
bf035663c9 dbus: Remove GroupMember object type and use Peer instead
GroupMember is unusable in itself and all the necessary informations are
stored in Peer objects, thus replace the use of GroupMember by Peer.

Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
2014-06-29 17:19:12 +03:00
Tomasz Bursztyka
c6386e5c71 P2P Add a utility to run a callback on all available groups
This will be useful in wpa_supplicant to match group's SSIDs against a
specific one.

Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
2014-06-29 16:56:57 +03:00
Tomasz Bursztyka
8e76f48abd P2P: Add a utility function to get the group configuration
This will be useful for finding the interface related to this group
after formation based on the group SSID.

Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
2014-06-29 16:52:06 +03:00
Jouni Malinen
37d8a27401 TDLS: Clean up add/set peer operations
Use a helper function to avoid multiple copies of the same long list of
argument parameters to wpa_sm_tdls_peer_addset() from the peer entry.

Signed-off-by: Jouni Malinen <j@w1.fi>
2014-06-29 13:44:15 +03:00
Arik Nemtsov
bcd2baa0fa TDLS: Tear down connection on malformed Setup Confirm
Otherwise the peer will erroneously assume we have a working direct
link.

Signed-off-by: Arik Nemtsov <arikx.nemtsov@intel.com>
2014-06-29 13:44:14 +03:00
Arik Nemtsov
81905409b5 TDLS: Abort local setup when failing to add STA
The driver might not always be able to add the new station. Abort the
setup when this happens.

Signed-off-by: Arik Nemtsov <arikx.nemtsov@intel.com>
2014-06-29 13:44:14 +03:00
Arik Nemtsov
1dce7a216f TDLS: Update peer STA as soon as full peer info is available
Update the peer STA with full info sending TDLS Setup Response/Confirm
frames instead of after the full setup exchange. This makes it easier
for some drivers to properly negotiate QoS and HT information on the
direct link.

Signed-off-by: Arik Nemtsov <arikx.nemtsov@intel.com>
2014-06-29 13:44:14 +03:00
Arik Nemtsov
819c943a3b TDLS: Remove peer from global peer-list on free
There is no need to keep the peer entry in memory after the link has
been removed.

Signed-off-by: Arik Nemtsov <arikx.nemtsov@intel.com>
Tested-by: Ilan Peer <ilan.peer@intel.com>
2014-06-29 13:44:14 +03:00
Michal Kazior
5841958f26 hostapd: Use channel switch fallback on error
It's worth giving a try to fallback to re-starting BSSes at least once
hoping it works out instead of just leaving BSSes disabled.

Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
2014-06-28 11:13:11 +03:00
Michal Kazior
8974620e3e hostapd: Perform multi-BSS CSA for DFS properly
Currently hostapd data structures aren't ready for multi-channel BSSes,
so make DFS work now at least with single-channel multi-BSS channel
switching.

Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
2014-06-28 11:08:16 +03:00
Michal Kazior
6782b6846b hostapd: Move CSA parameters to hostapd_data
This prepares CSA structure and logic in hostapd for multi-BSS channel
switching.

Signed-hostap: Michal Kazior <michal.kazior@tieto.com>
2014-06-28 11:02:39 +03:00
Christopher Wiley
3c5d34e30b Change channel before IBSS associations
Fix a bug where changing the mode of the interface to IBSS
fails because the interface is sitting on a channel where IBSS is
disallowed because of a previous association.

Signed-off-by: Christopher Wiley <wiley@chromium.org>
2014-06-28 10:46:33 +03:00
Christopher Wiley
ebffdbc493 nl80211: Refactor mode switch logic
In preparation for another wrinkle around switching into IBSS mode,
refactor existing mode switch logic for simplicity at the expense
of some brevity.

Signed-off-by: Christopher Wiley <wiley@chromium.org>
2014-06-28 10:42:05 +03:00
Pontus Fuchs
f95a4524c2 nl80211: Improve debug output by printing SA and DA in frames
Signed-off-by: Pontus Fuchs <pontus.fuchs@gmail.com>
2014-06-22 00:54:06 +03:00
Pontus Fuchs
dedfa440ed Print frame type name in debug output
"stype=4" becomes "stype=4 (WLAN_FC_STYPE_PROBE_REQ)" etc.

Signed-off-by: Pontus Fuchs <pontus.fuchs@gmail.com>
2014-06-22 00:51:39 +03:00
Johannes Berg
57a8f8af38 nl80211: Use low-priority scan for OBSS scan
Some drivers may support low-priority scans, if they do then
use that for OBSS scanning.

Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2014-06-22 00:47:06 +03:00
Jouni Malinen
1b928f96b6 P2P: Allow passphrase length to be configured
Previously, eight character random passphrase was generated
automatically for P2P GO. The new p2p_passphrase_len parameter can be
used to increase this length to generate a stronger passphrase for cases
where practicality of manual configuration of legacy devices is not a
concern.

Signed-off-by: Jouni Malinen <j@w1.fi>
2014-06-22 00:15:53 +03:00
Jouni Malinen
f3c6b230dd EAP-SIM': Fix AT_KDF parser to avoid infinite loop
Hitting maximum number of AT_KDF attributes could result in an infinite
loop due to the attribute parser not incrementing the current position
properly when skipping the extra KDF.

Signed-off-by: Jouni Malinen <j@w1.fi>
2014-06-21 12:20:52 +03:00
Jouni Malinen
79122f9f9c EAP-SIM/AKA: Remove unused RESULT_FAILURE state
This was not set anywhere, so remove the unnecessary code trying to
handle the unused state.

Signed-off-by: Jouni Malinen <j@w1.fi>
2014-06-21 00:26:29 +03:00
Jouni Malinen
4075e2fe77 EAP-GPSK: Clean up CSuite_List length validation (CID 62854)
Use a local variable and size_t in length comparison to make this easier
for static analyzers to understand. In addition, set the return list and
list_len values at the end of the function, i.e., only in success case.
These do not change the actual behavior of the only caller for this
function, but clarifies what the helper function is doing.

Signed-off-by: Jouni Malinen <j@w1.fi>
2014-06-18 17:14:59 +03:00
Jouni Malinen
2dbc959699 EAP-FAST: Clean up TLV length validation (CID 62853)
Use size_t instead of int for storing and comparing the TLV length
against the remaining buffer length to make this easier for static
analyzers to understand.

Signed-off-by: Jouni Malinen <j@w1.fi>
2014-06-18 16:45:03 +03:00
Jouni Malinen
35cbadbb14 VHT: Remove useless validation code from Operating Mode Notification
This was added by commit 8a45811638
('hostapd: Add Operating Mode Notification support'), but the validation
steps cannot be true either for the channel width (which is a two-bit
subfield that cannot encode more than the list four values) or Rx NSS
(which cannot encode a value larger 7). Furthermore, the VHT_CHANWIDTH_*
defines do not match the definition of the Channel Width subfield
values.

Since this check cannot ever match, it is better to remove it to make
the code easier to understand and to avoid getting complaints about dead
code from static analyzers.

Signed-off-by: Jouni Malinen <j@w1.fi>
2014-06-18 00:45:48 +03:00
Arik Nemtsov
bed7eb6808 TDLS: Do not bail when failing to process IEs in Discovery Request
Some APs (Cisco) may tack on a weird IE to the end of a TDLS Discovery
Request packet. This needn't fail the response, since the required IEs
are verified separately.

Signed-off-by: Arik Nemtsov <arikx.nemtsov@intel.com>
2014-06-17 17:08:42 +03:00
Arik Nemtsov
7e0f4f470a TDLS: Do not reject TPK M3 when failing to process IEs
Some APs (Cisco) may tack on a weird IE to the end of the TDLS confirm
packet, which can fail negotiation. As an interoperability workaround,
ignore IE parser failures and reject the frame only if any of the
mandatory IEs are not included.

Signed-off-by: Arik Nemtsov <arikx.nemtsov@intel.com>
2014-06-17 17:05:23 +03:00
Jouni Malinen
7efc7f66b1 TDLS: Fix TPK M1 error case (CID 68214)
Commit 342bce63cd introduced a possibility
of a NULL pointer dereference on the error path if a new peer entry
fails to get added (i.e., memory allocation failure). Fix that by
skipping the wpa_tdls_peer_free() call if necessary.

Signed-off-by: Jouni Malinen <j@w1.fi>
2014-06-17 01:57:35 +03:00
Jithu Jance
d1bb7aeda4 nl80211: Fix non-hostapd interface addition to not call add_ifidx()
Commit b36935be1a ('nl80211: Fix EAPOL
frames not being delivered') and commit
147848ec4d ('nl80211: Do not add all
virtual interfaces to drv->if_indices') were not fully in sync and it
was possible for some non-hostapd use cases to end up adding undesired
ifindexes into the list of interfaces from which events and EAPOL frames
are processed on the parent interface. This could result, e.g., in P2P
Device management interface on getting unexpected events, including
RTM_NEWLINK event that could end up getting interpreted as an
indication of the interface being down and unavailable.

Make both add_ifidx() calls use the same criteria for adding interfaces
to the local list. This is not really a complete solution, but it is
good enough for now to fix the most visible side effects of this issue.

Signed-off-by: Jithu Jance <jithu@broadcom.com>
2014-06-17 01:35:07 +03:00
Arik Nemtsov
342bce63cd TDLS: Bail on STA add failure in tpk_m1 processing
The driver might not be able to add the TDLS STA. Fail if this happens.
Also fix the error path to always reset the TDLS peer data.

Signed-off-by: Arik Nemtsov <arikx.nemtsov@intel.com>
2014-06-16 23:36:42 +03:00
Arik Nemtsov
947f900fb8 TDLS: Handle unreachable link teardown for external setup
If a link is unreachable, the specification mandates we should send a
teardown packet via the AP with a specific teardown reason. Force this
by first disabling the link and only then sending the teardown packet
for the LOW_ACK event.

Rename the TDLS LOW_ACK event handler to better reflect its purpose.

Signed-off-by: Arik Nemtsov <arikx.nemtsov@intel.com>
2014-06-16 23:34:06 +03:00
Amarnath Hullur Subramanyam
cf1600ace4 hostapd: Configure driver ACL even if MAC address list is empty
Earlier commit related to MAC address based access control list
offloaded to the driver was not sending ACL configuration to the driver
if the MAC address list was empty. Remove this check as empty access
control list is a valid use case and sending ACL parameters should not
be dependent on whether the list is empty.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2014-06-16 16:22:36 +03:00
Ilan Peer
e3bd6e9dc0 P2P: Use another interface operating channel as listen channel
Performing a P2P Device flow such as p2p_listen or
p2p_find, can degrade the performance of an active interface
connection, if the listen frequency is different than the
frequency used by that interface.

To reduce the effect of P2P Device flows on other interfaces,
try changing the listen channel of the P2P Device to match the
operating channel of one of the other active interfaces. This change
will be possible only in case that the listen channel is not forced
externally, and will be delayed to a point where the P2P Device
state machine is idle.

The optimization can be configured in the configuration file and
is disabled by default.

Signed-off-by: Ilan Peer <ilan.peer@intel.com>
2014-06-15 00:46:11 +03:00
Ilan Peer
751b00ba28 P2P: Modify p2p_get_pref_freq
In p2p_get_pref_freq, if the channels argument is NULL, select a
preferred channel that is also one of the P2P Device configured
channels.

Signed-off-by: Ilan Peer <ilan.peer@intel.com>
2014-06-15 00:21:41 +03:00
Jouni Malinen
e6270129f6 Clean up EAPOL-Key Key Data processing
Use a single location in wpa_sm_rx_eapol() for preparing the pointer to
the Key Data field and to its validated length instead of fetching that
information in number of processing functions separately.

Signed-off-by: Jouni Malinen <j@w1.fi>
2014-06-14 19:02:46 +03:00
Jouni Malinen
d56d7e56e3 Clean up EAPOL-Key processing
Re-order wpa_sm_rx_eapol() to first go through all EAPOL (802.1X) header
validation steps using the original message buffer and re-allocate and
copy the frame only if this is a valid EAPOL frame that contains an
EAPOL-Key. This makes the implementation easier to understand and saves
unnecessary memory allocations and copying should other types of EAPOL
frames get here.

Signed-off-by: Jouni Malinen <j@w1.fi>
2014-06-14 18:31:14 +03:00
Jouni Malinen
8605eabd54 EAP-EKE: Fix typos in debug message
These error messages had an incorrect frame name (likely copy-pasted
from the commit message handler) and couple of typos.

Signed-off-by: Jouni Malinen <j@w1.fi>
2014-06-14 17:26:52 +03:00
Jouni Malinen
ac79fcfa76 wext: Verify set_ssid results consistently (CID 62842)
Note in debug log if SSID clearing to stop pending cfg80211 association
attempts fail.

Signed-off-by: Jouni Malinen <j@w1.fi>
2014-06-14 12:32:53 +03:00
Jouni Malinen
305000e160 WPS: Check wps_build_wfa_ext() return value consistently (CID 68104)
While this call cannot really fail, check the return value to be more
consistent with all the other wps_build_wfa_ext() calls.

Signed-off-by: Jouni Malinen <j@w1.fi>
2014-06-14 12:32:52 +03:00
Jouni Malinen
2485835ba3 EAP-MSCHAPv2: Check hash function results more consistently (CID 68105)
While the hash functions would be very unlikely to fail in practice,
they do have option of returning an error. Check that return value more
consistently.

Signed-off-by: Jouni Malinen <j@w1.fi>
2014-06-14 12:32:45 +03:00
Jouni Malinen
b7c61c9d4e Fix validation of EAPOL-Key length with AES key wrap (CID 62859)
The additional eight octet field was removed from keydatalen without
proper validation of the Key Data Length field. It would have been
possible for an invalid EAPOL-Key frame to be processed in a way that
ends up reading beyond the buffer. In theory, this could have also
resulted in writing beyond the EAPOL-Key frame buffer, but that is
unlikely to be feasible due to the AES key wrap validation step on
arbitrary memory contents.

Signed-off-by: Jouni Malinen <j@w1.fi>
2014-06-14 00:20:04 +03:00
Jouni Malinen
6590b6400f EAP-TNC: Limit maximum message buffer to 75000 bytes (CID 62873)
Since there is a limit on the EAP exchange due to maximum number of
roundtrips, there is no point in allowing excessively large buffers to
be allocated based on what the peer device claims the total message to
be. Instead, reject the message if it would not be possible to receive
it in full anyway.

Signed-off-by: Jouni Malinen <j@w1.fi>
2014-06-13 16:03:45 +03:00
Jouni Malinen
da995b2e11 WNM: Use cleaner way of generating pointer to a field (CID 68099)
The Action code field is in a fixed location, so the IEEE80211_HDRLEN
can be used here to clean up bounds checking to avoid false reports from
static analyzer.

Signed-off-by: Jouni Malinen <j@w1.fi>
2014-06-13 00:27:15 +03:00
Jouni Malinen
062833c67c GAS server: Fix request frame length validation (CID 68098)
There seemed to be an off-by-one error in the validation of GAS request
frames. If a Public Action frame without the Action code field would
have reached this function, the length could have been passed as
(size_t) -1 which would likely have resulted in a crash due to reading
beyond the buffer. However, it looks like such frame would not be
delivered to hostapd at least with mac80211-based drivers. Anyway, this
function better be more careful with length validation should some other
driver end up reporting invalid Action frames.

In addition, the Action code field is in a fixed location, so the
IEEE80211_HDRLEN can be used here to clean up bounds checking to avoid
false reports from static analyzer.

Signed-off-by: Jouni Malinen <j@w1.fi>
2014-06-13 00:27:15 +03:00
Jouni Malinen
5ce3ae4c8f HT: Use cleaner way of generating pointer to a field (CID 68097)
The Action code field is in a fixed location, so the IEEE80211_HDRLEN
can be used here to clean up bounds checking to avoid false reports from
static analyzer.

Signed-off-by: Jouni Malinen <j@w1.fi>
2014-06-13 00:27:15 +03:00
Jouni Malinen
c02f35fb59 WPS: Clean up indentation level (CID 68109)
The implementation here was doing what it was supposed to, but the code
was indented in a way that made it quite confusing in the context of a
single line if statement body.

Signed-off-by: Jouni Malinen <j@w1.fi>
2014-06-12 19:45:31 +03:00
Philippe De Swert
68e2b8882a TNC: Fix minor memory leak (CID 62848)
In tncc_read_config(), the memory allocted for the config
did not get freed if an error occured.

Signed-off-by: Philippe De Swert <philippe.deswert@jollamobile.com>
2014-06-12 19:44:58 +03:00
Jouni Malinen
a0ab408d3b P2P: Fix SD and DevDisc to limit maximum wait time per driver support
The driver may reject offchannel TX operation if the requested wait time
is longer than what the driver indicates as the maximum
remain-on-channel time. Two of the P2P action frame cases used long
enough wait times (1000 ms for DevDisc and 5000 ms for SD) that could go
beyond the limit with some drivers. Fix these to limit the maximum wait
to what the driver indicates as supported.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2014-06-12 10:49:19 +03:00
Ashok Kumar Ponnaiah
3dacd3ece7 atheros: Add support for new GCMP/CCMP/CMAC/GMAC cipher suites
Extend the set of supported cipher suites to include CCMP-256, GCMP,
GCMP-256, CMAC-256, GMAC, and GMAC-256 when ATH_GCM_SUPPORT=y is set in
the build configuration.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2014-06-09 19:21:48 +03:00
Jouni Malinen
737754dc2b EAP-IKEv2: Remove obsolete ccns.pl project workarounds
It does not look like there is going to be any additional use for this
old build option that could be used to build the EAP-IKEv2 peer
implementation in a way that interoperates with the eap-ikev2.ccns.pl
project. Remove the workarounds that matches incorrect implementation in
that project to clean up implementation.

Signed-off-by: Jouni Malinen <j@w1.fi>
2014-06-08 12:28:36 +03:00
Jouni Malinen
aa6bf6dabc eap_proxy: Check sm != NULL more consistently
While it does not look like that eapol_sm_get_key() would ever be called
with sm == NULL, the current implementation is inconsistent on whether
that is allowed or not. Check sm != NULL consistently to avoid warnings
from static analyzers.

Signed-off-by: Jouni Malinen <j@w1.fi>
2014-06-07 19:26:41 +03:00
Jouni Malinen
4f4d51e059 TDLS: Add extra validation step for responder RSN IE length
The following kde.rsn_ie_len != peer->rsnie_i_len was already taking
care of enforcing the length to be within the target buffer length.
Anyway, this explicit check makes this clearer and matches the design in
TPK M1 processing.

Signed-off-by: Jouni Malinen <j@w1.fi>
2014-06-07 19:21:48 +03:00
Jouni Malinen
1fde15a20a GAS server: Explicitly check that home realm is available
This makes the code easier to understand for static analyzers to avoid
false reports.

Signed-off-by: Jouni Malinen <j@w1.fi>
2014-06-07 19:05:33 +03:00
Jouni Malinen
aff0bee78a GAS server: Remove unused function parameter
This parameter was not used at all, so just remove the argument instead
of passing NULL.

Signed-off-by: Jouni Malinen <j@w1.fi>
2014-06-07 19:04:17 +03:00
Jouni Malinen
86388afa56 WPS: Check for theoretical gmtime() failure
In theory, gmtime() could return NULL if the year value would not fit
into an integer. However, that cannot really happen with the current
time() value in practice. Anyway, clean up static analyzer reports by
checking for this corner case.

Signed-off-by: Jouni Malinen <j@w1.fi>
2014-06-07 17:39:51 +03:00
Jouni Malinen
d75a5ae018 WPS ER: Fix UDN parser to handle missing field
Must check that UDN was present before trying to parse it. Avoid a NULL
pointer dereference by checking the result before using os_strstr() when
parsing device description from an AP.

Signed-off-by: Jouni Malinen <j@w1.fi>
2014-06-07 17:35:22 +03:00
Jouni Malinen
bc32bb70d7 Make a code path easier for static analyzers to understand
prev cannot be NULL here in the hostapd_eid_country_add() call since
prev is set whenever start becomes non-NULL. That seems to be a bit too
difficult for some static analyzers, so check the prev pointer
explicitly to avoid false warnings.

Signed-off-by: Jouni Malinen <j@w1.fi>
2014-06-07 15:37:31 +03:00
Jouni Malinen
2a57c33e25 Reserve QCA vendor specific nl80211 commands 20..33
These are reserved for QCA use.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2014-06-05 17:03:17 +03:00
Amar Singhal
84df167554 nl80211: Add vendor attribute for interface index
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2014-06-05 16:57:52 +03:00
Jouni Malinen
9949483c2f The master branch is now used for v2.3 development
Signed-off-by: Jouni Malinen <j@w1.fi>
2014-06-05 00:51:02 +03:00
Jouni Malinen
b63b9a7bc9 Change version information for the 2.2 release
Signed-off-by: Jouni Malinen <j@w1.fi>
2014-06-04 16:09:59 +03:00
Darshan Paranji Sri
95b6bca66d Add rsn_pairwise bits to set_ieee8021x() driver_ops
This fixes an issue where a driver using the deprecated set_ieee8021x()
callback did not include rsn_pairwise bits in the driver configuration
even if mixed WPA+WPA2 configuration was used. This could result, e.g.,
in CCMP not being enabled properly when wpa_pairwise=TKIP and
rsn_pairwise=CCMP was used in the configuration. Fix this by using
bitwise OR of the wpa_pairwise and rsn_pairwise values to allow the
driver to enable all pairwise ciphers.

In addition, make the newer set_ap() driver_ops use the same bitwise OR
design instead of picking between rsn_pairwise and wpa_pairwise. This
makes the code paths consistent and can also fix issues with mixed mode
configuration with set_ap().

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2014-06-03 13:59:22 +03:00
Jouni Malinen
95f6f6a49d RADIUS/EAP server: Use longer username buffer to avoid truncation
If the peer provides a username with large part of it being non-ASCII
characters, the previously used buffers may not have been long enough to
include the full string in debug logs and database search due to forced
truncation of the string by printf_encode(). Avoid this by increasing
the buffer sizes to fit in the maximum result.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2014-06-02 17:36:51 +03:00
Jouni Malinen
ee54e4010e tests: printf_encode unit test for bounds checking
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2014-06-02 17:36:51 +03:00
Stuart Henderson
5dff6dff63 Fix off-by-one bounds checking in printf_encode()
The off-by-one error in printf_encode() bounds checking could have
allowed buffer overflow with 0x00 being written to the memory position
following the last octet of the target buffer. Since this output is used
as \0-terminated string, the following operation would likely read past
the buffer as well. Either of these operations can result in the process
dying either due to buffer overflow protection or by a read from
unallowed address.

This has been seen to cause wpa_supplicant crash on OpenBSD when control
interface client attaches (debug print shows the client socket address).
Similarly, it may be possible to trigger the issue in RADIUS/EAP server
implementation within hostapd with a suitable constructed user name.

Signed-off-by: Stuart Henderson <sthen@openbsd.org>
2014-06-02 17:36:18 +03:00
Ashok Kumar Ponnaiah
801e117376 Fix validation of RSN EAPOL-Key version for GCMP with PMF
If PMF was enabled, the validation step for EAPOL-Key descriptor version
ended up rejecting the message if GCMP had been negotiated as the
pairwise cipher. Fix this by making the GCMP check skipped similarly to
the CCMP case if a SHA256-based AKM is used.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2014-06-02 17:03:33 +03:00
Jouni Malinen
3d4d2348c0 FT: Fix GTK rekeying after FT protocol
Move to PTKINITDONE state and mark PTK valid after successful completion
of FT protocol. This allows the AP/Authenticator to start GTK rekeying
when FT protocol is used. Previously, the station using FT protocol did
not get the new GTK which would break delivery of group addressed
frames.

Signed-off-by: Jouni Malinen <j@w1.fi>
2014-06-01 13:21:40 +03:00
Jithu Jance
d3d048310c nl80211: Work around error case prints for nl_recvmsgs on Android
I got the below prints on a particular Android platform:

I/wpa_supplicant( 2637): nl80211: send_and_recv->nl_recvmsgs failed: 20
I/wpa_supplicant( 2637): nl80211: send_and_recv->nl_recvmsgs failed: 20

In JellyBean libnl_2 code, I see that the nl_recvmsgs returns postive values
too. In some cases, nl_recvmgs return the output of nl_recv function. nl_recv
function can return Number of bytes read, 0 or a negative error code.

Looks like this positive return value for nl_recvmsgs may be specific to
Android. While this is not how the API is supposed to work, this does no
harm with upstream libnl which returns only 0 or -1 from the function.

Signed-off-by: Jithu Jance <jithu@broadcom.com>
2014-06-01 11:25:02 +03:00
Jouni Malinen
8a387a269d P2P NFC: Fix use of freed memory
The dev_found() callback from NFC connection handover message processing
ended up using the p2p_dev_addr pointer that points to the parsed
message. However, that parsed data was freed just before the call. Fix
this by reordering the calls.

Signed-off-by: Jouni Malinen <j@w1.fi>
2014-05-31 23:10:33 +03:00
Jouni Malinen
13c330385a SAE: Fix memory leak in random number generation
If the randomly generated bignum does not meet the validation steps, the
iteration loop in sae_get_rand() did not free the data properly. Fix the
memory leak by freeing the temporary bignum before starting the next
attempt at generating the value.

Signed-off-by: Jouni Malinen <j@w1.fi>
2014-05-31 22:24:31 +03:00
Jouni Malinen
d92bdf9602 hostapd: Make sure hapd->drv_priv gets cleared on driver deinit
Couple of code paths in hostapd.c could have left hapd->drv_priv
pointing to memory that was freed in driver_nl80211.c when a secondary
BSS interface is removed. This could result in use of freed memory and
segfault when the next driver operation (likely during interface
deinit/removal). Fix this by clearing hapd->drv_priv when there is
reason to believe that the old value is not valid within the driver
wrapper anymore.

Signed-off-by: Jouni Malinen <j@w1.fi>
2014-05-31 17:11:04 +03:00
Jouni Malinen
438e13339d hostapd: Use helper function to avoid duplicate deinit calls
These three calls were used already in three different paths. Use a
helper function to avoid adding even more copies of this.

Signed-off-by: Jouni Malinen <j@w1.fi>
2014-05-31 15:57:36 +03:00
Michal Kazior
ac1a224092 hostapd: Clean up if interface setup fails
If for some reason interface setup fails mid-way when setting up
multi-BSS AP it was possible to get segmentation fault because driver
was not properly cleaned up.

One possible trigger, when using nl80211 driver, was udev renaming an
interface created by hostapd causing, e.g., linux_set_iface_flags() to
fail.

Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
2014-05-31 15:53:56 +03:00
Michal Kazior
81c4fca100 hostapd: Reset hapd->interface_add properly
This variable is updated when calling hostapd_if_add(), so it makes
sense to do the same thing when calling hostapd_if_remove().

Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
2014-05-31 15:49:38 +03:00
Michal Kazior
3fbd036ea9 hostapd: Prevent double interface disabling from segfaulting
Performing, e.g. `wpa_cli -p /var/run/hostapd raw DISABLE` twice led to
hostapd segmentation fault if multiple BSSes were configured. Fix this
by checking if there is anything to disable at all before trying.

Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
2014-05-31 15:46:45 +03:00
Michal Kazior
ea39367c1b nl80211: Fix wpa_driver_nl80211_if_add() failure paths
Make sure to not remove interfaces that were not created by
hostapd/wpa_supplicant. This was already done on number of the error
paths, but not all.

Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
2014-05-31 13:43:27 +03:00
Jouni Malinen
b523973611 RADIUS client: Trigger failover more quickly if socket is not valid
It is possible for the connect() call to fail (e.g., due to unreachable
network based on local routing table), so the current auth/acct_sock may
be left to -1. Use that as an addition trigger to allow server failover
operation to be performed more quickly if it is known that the
retransmission attempt will not succeed anyway.

Signed-off-by: Jouni Malinen <j@w1.fi>
2014-05-30 20:52:08 +03:00
Jouni Malinen
09844c0984 RADIUS client: Do not flush pending messages if server did not change
The re-open socket to the current RADIUS server code path did not work
in the expected way here. The pending authentication messages do not
need to be flushed in that case and neither should the retransmission
parameters be cleared. Fix this by performing these operations only if
the server did actually change as a part of a failover operation.

Signed-off-by: Jouni Malinen <j@w1.fi>
2014-05-30 20:46:20 +03:00
Jouni Malinen
5d67bf1566 hostapd: Fix configuration of multiple RADIUS servers with SET
The current RADIUS server pointer was updated after each SET command
which broke parsing of multiple RADIUS servers over the control
interface. Fix this by doing the final RADIUS server pointer updates
only once the full configuration is available.

Signed-off-by: Jouni Malinen <j@w1.fi>
2014-05-30 20:40:11 +03:00
Jouni Malinen
70d4084885 RADIUS client: Fix socket close/re-open on server change
Both IPv4 and IPv6 sockets were not closed consistently in the paths
that tried to change RADIUS servers. This could result in leaking
sockets and leaving behind registered eloop events to freed memory on
interface removal.

Signed-off-by: Jouni Malinen <j@w1.fi>
2014-05-30 18:09:42 +03:00
Jerry Yang
d045cc8e4c RADIUS client: Fix crash issue in radius_client_timer()
While iterating through RADIUS messages in radius_client_timer(), one
message entry may get flushed by "radius_client_retransmit -->
radius_client_handle_send_error --> radius_client_init_auth -->
radius_change_server --> radius_client_flush". This could result in
freed memory being accessed afterwards.

Signed-off-by: Jerry Yang <xyang@sonicwall.com>
2014-05-30 18:08:59 +03:00