This extends ap_wps_pbc_timeout to cover another long WPS timeout:
ER-initiated SetSelectedRegistrar timeout on AP. Using the same test
case for this avoids the need for another 120 second test case.
Signed-off-by: Jouni Malinen <j@w1.fi>
Pass absolute path to the daemonized wpa_cli process and add read
privileges for everyone on the action script to make this test case work
better when run without a VM.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
It looks like the previous timeout of 0.1 seconds could be hit under
parallel VM load, so double this to 0.2 second to avoid hitting
unnecessary test failures.
Signed-off-by: Jouni Malinen <j@w1.fi>
The test sequence "scan_and_bss_entry_removed ap_wps_ap_scan_2" resulted
in failure due to an old BSS entry remaining from the first test case to
the second and the WPS_PBC operation on a forced BSSID ending up picking
the incorrect BSS entry. Make this more robust by clearing the scan
results from cfg80211.
Signed-off-by: Jouni Malinen <j@w1.fi>
Both of these test cases were leaving out BSS entries with active PBC
mode at the end of the test. This could result in the next text case
failing, e.g., in "ap_wps_pbc_overlap_2ap grpform_ext_listen" and
"ap_wps_pbc_overlap_2sta grpform_ext_listen" sequences. Fix this by
flushing the scan results more carefully at the end of the PBC overlap
test cases.
Signed-off-by: Jouni Malinen <j@w1.fi>
run-tests.py is running as root, so sudo does not need to be used
anymore from within each test case.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
There is no need to use sudo and external rm to remove files now that
run-tests.py is required to run as root.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
The test used p2p_dev_addr() that can be different from own_addr()
if a dedicated P2P Device interface is used.
Signed-off-by: Ben Rosenfeld <ben.rosenfeld@intel.com>
Reorder scanning in a way that allows the ER behavior to be more
predictable. The first Probe Request report is for a previously received
frame on the AP and this new sequence avoids leaving either of the PBC
test STAs to be that one.
Signed-off-by: Jouni Malinen <j@w1.fi>
Instead of returning "skip" from the test function, raise the new
HwsimSkip exception to indicate a test case was skipped.
Signed-off-by: Jouni Malinen <j@w1.fi>
It was possible for regulatory domain changes to "leak" into following
test cases in number of cases where the cfg80211 BSS table remained
after regulatory domain had been restored to world roaming. Try to make
this less likely to occur by explicitly clearing BSS table at the end of
test cases that use different regulatory domain. This makes P2P test
cases that verify channel selection based on world roaming rules more
robust.
Signed-off-by: Jouni Malinen <j@w1.fi>
This avoids one more cleanup step between most test cases by stopping ER
only in case it was actually used during a test.
Signed-off-by: Jouni Malinen <j@w1.fi>
A single channel scan just before WPS_REG, WPS_PBC, and WPS_PIN commands
can be used to avoid having to run a full scan. This saves significant
amount of time in the WPS test cases.
Signed-off-by: Jouni Malinen <j@w1.fi>
This makes it more convenient and consistent to clear the cached scan
results from cfg80211 and wpa_supplicant.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
The "Not fully connected" report did not clearly identify what went
wrong, so make this more verbose in hope of being able to determine what
happened should this test case fail again.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
It was possible to hit the 10 second timeout in some test cases under
heavy load (e.g., with large number of VMs running tests in parallel).
These timeouts are not really indicating any real error, so make them
less likely to show up in reports by increasing the connection timeout
to 30 seconds.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This is needed in preparation for WPS AES being mapped to enabling both
CCMP and GCMP if the driver supports both ciphers.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
The scan for WPS-AUTH validation may miss a Probe Response frame if the
hostapd process gets blocked under load, e.g., when testing with
parallel-vm.sh.
Signed-off-by: Jouni Malinen <j@w1.fi>
