Commit graph

4439 commits

Author SHA1 Message Date
Bhagavathi Perumal S
d57e06170b wpa_supplicant: Make channel switch event available for non-AP builds
This allows user to get channel switch indication in station mode even
if wpa_supplicant is built without CONFIG_AP=y.

Signed-off-by: Bhagavathi Perumal S <bperumal@codeaurora.org>
2018-05-04 20:31:23 +03:00
Bhagavathi Perumal S
d7f038ded2 wpa_supplicant: Add ieee80211ac information in STATUS
This allows user to get current operating mode of station.

Signed-off-by: Bhagavathi Perumal S <bperumal@codeaurora.org>
2018-05-04 20:18:55 +03:00
Sean Parkinson
ab35793ec1 wolfSSL: Fix EAP-FAST key derivation
Implement tls_connection_get_eap_fast_key() using cryptographic
primitives as wolfSSL implements different spec.

Signed-off-by: Sean Parkinson <sean@wolfssl.com>
2018-05-02 13:32:51 +03:00
Jouni Malinen
bbbc7e8016 EAP-TLS: Extend TLS version config to allow TLS v1.3 to be disabled
This may be needed to avoid interoperability issues with the new
protocol version and significant changes for EAP use cases in both key
derivation and handshake termination.

Signed-off-by: Jouni Malinen <j@w1.fi>
2018-05-01 22:13:38 +03:00
Jouni Malinen
625a8c86ba wpa_cli: Indicate HS20-T-C-ACCEPTANCE to action scripts
This can be used to start a web browser to go through Terms and
Conditions acknowledgment.

Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
2018-04-29 20:02:13 +03:00
mazumdar
d239ab3962 DFS: Mark channels required DFS based on reg-domain info from the driver
Mark a channel as required DFS based on regulatory information received
from the driver/kernel rather than deciding based on hardcoded
boundaries on the frequency. Previously few channels were being marked
as requiring DFS even though they were non-DFS in a particular country.

If the driver does not provide channel list information, fall back to
the previously used frequency-based determination.

Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
2018-04-24 00:35:47 +03:00
Jouni Malinen
7fc6a024f9 HS 2.0: Process received Terms and Conditions Acceptance notification
Extend wpa_supplicant WNM-Notification RX handling to parse and process
received Terms and Conditions Acceptance notifications. If PMF is
enabled for the association, this frame results in control interface
indication (HS20-T-C-ACCEPTANCE <URL>) to get upper layers to guide the
user through the required acceptance steps.

Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
2018-04-24 00:35:47 +03:00
Jouni Malinen
72b6e5d1e2 Do not remove CCMP group cipher if any CCMP/GCMP cipher is enabled
CCMP group cipher was removed if CCMP was not allowed as a pairwise
cipher when loading a configuration file (but not actually when changing
configuration during runtime). This is needed to avoid issues with
configurations that use the default group cipher (TKIP CCMP) while
modifying pairwise cipher from the default CCMP TKIP) to TKIP. However,
there is not really a need to remove the CCMP group cipher if any GCMP
or CCMP cipher is enabled as a pairwise cipher.

Change the network profile validation routine to not remove CCMP as
group cipher if CCMP-256, GCMP, or GCMP-256 is enabled as a pairwise
cipher even if CCMP is not.

Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
2018-04-24 00:35:43 +03:00
Tova Mussai
c4315e6620 AP: Handle AP initalization failure in async flow
When AP initialization is completed in a callback (e.g., OBSS scan),
wpa_supplicant_deinit_ap() is not called in case of failure. Fix this by
calling setup_complete_cb in case of failure, too, which in turn calls
wpa_supplicant_deinit_ap() if needed.

Signed-off-by: Tova Mussai <tova.mussai@intel.com>
2018-04-20 00:48:49 +03:00
Ahmad Masri
86c998d37a FT: Add FT auth algorithm to connect params when roaming
Add WPA FT auth to connect params in case of a re-connection to ESS
supporting FT when FT was used in the first connect.

Signed-off-by: Ahmad Masri <amasri@codeaurora.org>
2018-04-20 00:35:41 +03:00
Ahmad Masri
3dc3afe298 FT: Add MDE to assoc request IEs in connect params
Add MDE (mobility domain element) to Association Request frame IEs in
the driver assoc params. wpa_supplicant will add MDE only if the network
profile allows FT, the selected AP supports FT, and the mobility domain
ID matches.

Signed-off-by: Ahmad Masri <amasri@codeaurora.org>
2018-04-20 00:32:49 +03:00
Bhagavathi Perumal S
b55c623e4c Make CENTER_FRQ1 available independently in SIGNAL_POLL
This allows user to get center frequency and find secondary channel
offset.

Signed-off-by: Bhagavathi Perumal S <bperumal@codeaurora.org>
2018-04-20 00:10:45 +03:00
Jouni Malinen
4204669c69 HS 2.0: Add Roaming Consortium Selection element into AssocReq
This makes wpa_supplicant add Hotspot 2.0 Roaming Consortium Selection
element into (Re)Association Request frames if the network profile
includes roaming_consortium_selection parameter.

Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
2018-04-18 01:12:25 +03:00
Jouni Malinen
6311547e7b HS 2.0: Add Roaming Consortium Selection network profile parameter
This adds new roaming_consortium_selection network profile parameter
into wpa_supplicant. This is used to store the OI that was used for
network selection (INTERWORKING_SELECT) based on matching against the
Roaming Consortium OIs advertised by the AP. This can also be used when
using an external component to perform selection.

This commit adds the network profile parameter, but does not yet include
it in (Re)Association Request frames.

Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
2018-04-17 17:26:56 +03:00
Jouni Malinen
5b7695275c HS 2.0: Use roaming_consortiums list to match OIs for access
This extends Hotspot 2.0 credential matching to consider the
roaming_consortiums parameter when determining whether the cred block
matches the information advertised by an AP.

Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
2018-04-17 17:26:53 +03:00
Jouni Malinen
909a948b0f HS 2.0: Add a new cred block parameter roaming_consortiums
This new string parameter contains a comma delimited list of OIs
(hexdump) in a string. This is used to store Hotspot 2.0
PerProviderSubscription/<X+>/HomeSP/RoamingConsortiumOI. This commit
includes the configuration changes to parse and write the parameter. The
actual values are not yet used in Interworking network selection.

Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
2018-04-17 16:40:47 +03:00
Jouni Malinen
9b6f93e4d6 HS 2.0: Document credential parameter required_roaming_consortium
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
2018-04-17 16:40:47 +03:00
Jouni Malinen
6a8a04d742 HS 2.0: Add fetching of Operator Icon Metadata ANQP-element
This extends wpa_supplicant Hotspot 2.0 ANQP routines to allow the
Operator Icon Metadata ANQP-element to be fetched with "ANQP_GET <bssid>
hs20:12". The result is available in the new hs20_operator_icon_metadata
entry in the "BSS <bssid>" output.

Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
2018-04-17 16:40:42 +03:00
Dmitry Lebed
37547ad63c wpa_supplicant: Increase authentication timeout if CAC is started
Timeout is increased by dfs_cac_ms from channel data, or by max CAC time
(10 minutes) if dfs_cac_ms is not defined. This is needed for some more
complex cases, e.g., when STA is acting as an active slave with DFS
offload enabled and decided to start CAC after receiving CONNECT
command, in such a case the 10 second timeout is too small and
wpa_supplicant need to wait for CAC completion or CAC timeout (up to 10
minutes).

Without such timeout modification wpa_supplicant will be unable to
connect to an AP on DFS channel, since the default authentication
timeout (10 s) is smaller than the minimum CAC time (60 s).

Tested with nl80211 DFS offload implementation.

Signed-off-by: Dmitry Lebed <dlebed@quantenna.com>
2018-04-15 22:20:49 +03:00
Dmitry Lebed
2dd5fbbff8 wpa_supplicant: Rename wpas_event_*() to wpas_ap_event_*()
Rename DFS event handling functions, since they are located in ap.c and
refer to AP-mode only. Needed to add some STA-mode DFS event handling.

Signed-off-by: Dmitry Lebed <dlebed@quantenna.com>
2018-04-15 22:07:09 +03:00
Jouni Malinen
a2ab37308a Fix sae_password documentation in wpa_supplicant to refer correct field
sae_password replaces psk, not passphrase, parameter in wpa_supplicant.

Signed-off-by: Jouni Malinen <j@w1.fi>
2018-04-13 12:09:33 +03:00
Daniel Golle
d5906fbb72 mesh: Properly handle sae_password
The recently introduced sae_password parameter was only handled properly
in wpa_supplicant/sme.c while wpa_supplicant/mesh.c assumed that
ssid->passphrase exclusively holds the secret.

Import the logic from sme.c to mesh.c to allow having only sae_password
set which otherwise throws this error:
AP-ENABLED
mesh: Passphrase for SAE not configured

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2018-04-13 12:09:33 +03:00
Jouni Malinen
852b2f2738 SAE: Only allow SAE AKMP for PMKSA caching attempts
Explicitly check the PMKSA cache entry to have matching SAE AKMP for the
case where determining whether to use PMKSA caching instead of new SAE
authentication. Previously, only the network context was checked, but a
single network configuration profile could be used with both WPA2-PSK
and SAE, so should check the AKMP as well.

Signed-off-by: Jouni Malinen <j@w1.fi>
2018-04-09 19:34:44 +03:00
Jouni Malinen
06b1a10434 SAE: Fix default PMK configuration for PMKSA caching case
The RSN supplicant state machine PMK was set based on WPA PSK even for
the cases where SAE would be used. If the AP allows PMKSA caching to be
used with SAE, but does not indicate the selected PMKID explicitly in
EAPOL-Key msg 1/4, this could result in trying to use the PSK instead of
SAE PMK. Fix this by not setting the WPA-PSK as default PMK for SAE
network profiles and instead, configuring the PMK explicitly from the
found PMKSA cache entry.

Signed-off-by: Jouni Malinen <j@w1.fi>
2018-04-09 13:10:08 +03:00
Jouni Malinen
66dbc8d9c3 Add more debug prints for wpa_sm_set_pmk() calls
Couple of these were not preceded by wpa_hexdump_key(PSK) which made it
more difficult to interpret the debug log.

Signed-off-by: Jouni Malinen <j@w1.fi>
2018-04-08 19:11:07 +03:00
Jouni Malinen
ee2c6bb5e5 Remove CONFIG_IEEE80211R_AP=y build option from wpa_supplicant
There is no existing mechanism for setting up AP mode functionality with
FT enabled, so there is not really much point in having a build option
for trying to include the AP-to-AP FT functionality into wpa_supplicant
either. Since this build option results in failures to complete the
build, simply remove it completely. This can be restored if there is
ever desire to enable FT functionality in wpa_supplicant controlled AP
mode.

Signed-off-by: Jouni Malinen <j@w1.fi>
2018-04-02 17:00:45 +03:00
Davide Caratti
d89edb6112 wpa_supplicant: Don't reply to EAPOL if pkt_type is PACKET_OTHERHOST
When wpa_supplicant is running on a Linux interface that is configured in
promiscuous mode, and it is not a member of a bridge, incoming EAPOL
packets are processed regardless of the Destination Address in the frame.
As a consequence, there are situations where wpa_supplicant replies to
EAPOL packets that are not destined for it.

This behavior seems undesired (see IEEE Std 802.1X-2010, 11.4.a), and can
be avoided by attaching a BPF filter that lets the kernel discard packets
having pkt_type equal to PACKET_OTHERHOST.

Signed-off-by: Davide Caratti <davide.caratti@gmail.com>
2018-04-02 12:21:27 +03:00
Vasyl Vavrychuk
8fb2b35735 Clean up setting of iface->p2p_mgmt flag
Previously we set this flag to one in wpa_supplicant_init_iface() if
Wi-Fi controller does not have a dedicated P2P-interface.

This setting had effect only in scope of wpa_supplicant_init_iface() and
it contradicts with comment to struct wpa_interface::p2p_mgmt field.
This comment says that this flag is used only if Wi-Fi controller has
dedicated P2P-device interface.

Also it contradicts with usage of similiar p2p_mgmt field in struct
wpa_supplicant. Again struct wpa_supplicant::p2p_mgmt is set only for
dedicated P2P-device interface.

After this change wpa_interface become input argument to
wpa_supplicant_init_iface() that we are not modifying.

Signed-off-by: Vasyl Vavrychuk <vvavrychuk@gmail.com>
2018-04-02 12:13:59 +03:00
Vasyl Vavrychuk
d53401c54b dbus: Redirect signal processing to the management device if present
This fixes sending of FindStopped, GroupFormationFailure, and
InvitationReceived signals in the case of separate P2P-Device interface.
This extends the coverage of the earlier commit
745d62322b ("dbus: Redirect P2P request to
the managment device if present") to these three functions that were
missing the redirection.

Some wireless controllers might have separate P2P-Device interface, see
as example result of 'iw dev':

phy#0
        Unnamed/non-netdev interface
                ...
                type P2P-device
                ...
        Interface wlp2s0
                type managed
                ...

In this case there is separate 'struct wpa_supplicant' created for this
p2p-dev-* device as result of 'wpa_supplicant_add_iface >
wpas_p2p_add_p2pdev_interface > wpa_supplicant_add_iface'.

This instance of wpa_supplicant is not registered in D-Bus
(wpas_dbus_register_*) since for corresponding P2P device interface flag
'struct wpa_interface > p2p_mgmt' is set.

But this instance is saved in p2p_init_wpa_s and is used for handling
P2P related D-Bus commands. Therefore we should look for D-Bus path in
the parent of p2p_init_wpa_s instance.

Without this change test dbus_p2p_discovery starts failing if we set
support_p2p_device in vm-run.sh.

Signed-off-by: Vasyl Vavrychuk <vvavrychuk@gmail.com>
2018-04-02 12:02:13 +03:00
Masashi Honma
e480212765 dbus: Add FILS to global capabilities
If any of the interfaces supports FILS (and similarly for FILS-SK-PFS),
include the "fils" (and "fils_sk_pfs") capability in D-Bus information.

Signed-off-by: Masashi Honma <masashi.honma@gmail.com>
2018-04-02 11:56:06 +03:00
Jaap Keuter
208263c014 Add config information related to MACsec
Add examples of relevant top level CONFIG clauses for wpa_supplicant
MACsec support to defconfig.

Extend the example of MACsec related network configuration. Also bring
them in line with the format of the other example network configurations.

Signed-off-by: Jaap Keuter <jaap.keuter@xs4all.nl>
2018-04-01 21:58:57 +03:00
Saurav Babu
e360010c3a dbus: Add mesh to global capabilities
Signed-off-by: Saurav Babu <saurav.babu@samsung.com>
2018-04-01 21:52:56 +03:00
Ahmed ElArabawy
45f7574d31 Propagate the EAP method error code
In the current implementation, upon an EAP method failure, followed by
an EAP failure, the EAP Status is propagated up in wpa_supplicant with a
general failure parameter string "failure". This parameter is used for a
notification on the dbus.

This commit reports the EAP method failure error code in a separate
callback.

The solution in this commit is generic to all EAP methods, and can be
used by any method that need to pass its error code. However, this
commit only implements the reporting for EAP-SIM and EAP-AKA methods
where the Notification Code (in AT_NOTIFICATION) is used as the method
specific error code value.

Signed-off-by: Ahmed ElArabawy <arabawy@google.com>
2018-03-31 11:57:33 +03:00
Beniamino Galvani
77a020a118 wpa_supplicant: Fix auth failure when the MAC is updated externally
When connecting to a WPA-EAP network and the MAC address is changed
just before the association (for example by NetworkManager, which sets
a random MAC during scans), the authentication sometimes fails in the
following way ('####' logs added by me):

wpa_supplicant logs:
 wlan0: WPA: RX message 1 of 4-Way Handshake from 02:00:00:00:01:00 (ver=1)
 RSN: msg 1/4 key data - hexdump(len=22): dd 14 00 0f ac 04 d8 21 9d a5 73 98 88 26 ef 03 d2 ce f7 04 7d 23
 WPA: PMKID in EAPOL-Key - hexdump(len=22): dd 14 00 0f ac 04 d8 21 9d a5 73 98 88 26 ef 03 d2 ce f7 04 7d 23
 RSN: PMKID from Authenticator - hexdump(len=16): d8 21 9d a5 73 98 88 26 ef 03 d2 ce f7 04 7d 23
 wlan0: RSN: no matching PMKID found
 EAPOL: Successfully fetched key (len=32)
 WPA: PMK from EAPOL state machines - hexdump(len=32): [REMOVED]
 #### WPA: rsn_pmkid():
 #### WPA: aa              - hexdump(len=6): 02 00 00 00 01 00
 #### WPA: spa             - hexdump(len=6): 66 20 cf ab 8c dc
 #### WPA: PMK             - hexdump(len=32): b5 24 76 4f 6f 50 8c f6 a1 2e 24 b8 07 4e 9a 13 1b 94 c4 a8 1f 7e 22 d6 ed fc 7d 43 c7 77 b6 f7
 #### WPA: computed PMKID  - hexdump(len=16): ea 73 67 b1 8e 5f 18 43 58 24 e8 1c 47 23 87 71
 RSN: Replace PMKSA entry for the current AP and any PMKSA cache entry that was based on the old PMK
 nl80211: Delete PMKID for 02:00:00:00:01:00
 wlan0: RSN: PMKSA cache entry free_cb: 02:00:00:00:01:00 reason=1
 RSN: Added PMKSA cache entry for 02:00:00:00:01:00 network_ctx=0x5630bf85a270
 nl80211: Add PMKID for 02:00:00:00:01:00
 wlan0: RSN: PMKID mismatch - authentication server may have derived different MSK?!

hostapd logs:
 WPA: PMK from EAPOL state machine (MSK len=64 PMK len=32)
 WPA: 02:00:00:00:00:00 WPA_PTK entering state PTKSTART
 wlan1: STA 02:00:00:00:00:00 WPA: sending 1/4 msg of 4-Way Handshake
 #### WPA: rsn_pmkid():
 #### WPA: aa              - hexdump(len=6): 02 00 00 00 01 00
 #### WPA: spa             - hexdump(len=6): 02 00 00 00 00 00
 #### WPA: PMK             - hexdump(len=32): b5 24 76 4f 6f 50 8c f6 a1 2e 24 b8 07 4e 9a 13 1b 94 c4 a8 1f 7e 22 d6 ed fc 7d 43 c7 77 b6 f7
 #### WPA: computed PMKID  - hexdump(len=16): d8 21 9d a5 73 98 88 26 ef 03 d2 ce f7 04 7d 23
 WPA: Send EAPOL(version=1 secure=0 mic=0 ack=1 install=0 pairwise=1 kde_len=22 keyidx=0 encr=0)

That's because wpa_supplicant computed the PMKID using the wrong (old)
MAC address used during the scan. wpa_supplicant updates own_addr when
the interface goes up, as the MAC can only change while the interface
is down. However, drivers don't report all interface state changes:
for example the nl80211 driver may ignore a down-up cycle if the down
message is processed later, when the interface is already up. In such
cases, wpa_supplicant (and in particular, the EAP state machine) would
continue to use the old MAC.

Add a new driver event that notifies of MAC address changes while the
interface is active.

Signed-off-by: Beniamino Galvani <bgalvani@redhat.com>
2018-03-30 12:16:42 +03:00
Jouni Malinen
64624f31cf OWE: Fix CONFIG_OWE=y build without CONFIG_IEEE80211R=y
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
2018-03-26 12:34:36 +03:00
Tamizh chelvam
ec2b5173ce Make STA opmode change event available to upper layers
Add an event callback for EVENT_STATION_OPMODE_CHANGED to allow
user/application to get the notification whenever there is a change in a
station's HT/VHT op mode.

The new events:
STA-OPMODE-MAX-BW-CHANGED <addr> <20(no-HT)|20|40|80|80+80|160>
STA-OPMODE-SMPS-MODE-CHANGED <addr> <automatic|off|dynamic|static>
STA-OPMODE-N_SS-CHANGED <addr> <N_SS>

Signed-off-by: Tamizh chelvam <tamizhr@codeaurora.org>
2018-03-19 20:07:22 +02:00
Purushottam Kushwaha
8179ae3a2a DPP: Support retrieving of configurator's private key
To retain configurator information across hostapd/wpa_supplicant
restart, private key need to be maintained to generate a valid pair of
authentication keys (connector, netaccess_key, csign) for new enrollees
in the network.

Add a DPP_CONFIGURATOR_GET_KEY control interface API through which the
private key of an existing configurator can be fetched.

Command format:
DPP_CONFIGURATOR_GET_KEY <configurator_id>

The output from this command can then be used with
"DPP_CONFIGURATOR_ADD key=<hexdump>" to create the same key again.

Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
2018-03-16 20:55:32 +02:00
Srinivas Dasari
d74963d411 DPP: Extend dpp_test 89 functionality to transmit side
This extends dpp_test functionality to allow DPP exchanges to be stopped
after authentication is completed on the Initiator, i.e., after sending
out the Authentication Confirm message. Previously, dpp_test=89 was used
only on the Responder side to stop after receiving the Authentication
Confirm message. The main use case for this extended functionality is to
be able to stop the protocol exchange on a device that acts as
authentication Initiator and Enrollee.

Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
2018-03-13 01:03:37 +02:00
Davide Caratti
22151b111b wpa_supplicant: Fix memory leaks in ieee802_1x_create_preshared_mka()
In case MKA is initialized successfully, local copies of CAK and CKN
were allocated, but never freed. Ensure that such memory is released
also when ieee802_1x_kay_create_mka() returns a valid pointer.

Fixes: ad51731abf ("wpa_supplicant: Allow pre-shared (CAK,CKN) pair for MKA")
Signed-off-by: Davide Caratti <davide.caratti@gmail.com>
2018-03-11 17:01:14 +02:00
Sean Parkinson
fec03f9838 Add support for wolfSSL cryptographic library
Allow hostapd/wpa_supplicant to be compiled with the wolfSSL
cryptography and TLS library.

Signed-off-by: Sean Parkinson <sean@wolfssl.com>
2018-03-03 11:52:40 +02:00
Avraham Stern
b8e88d357a wpa_supplicant: Handle port authorized event
When the driver indicates that the connection is authorized (i.e., the
4-way handshake was completed by the driver), cancel the EAP
authentication timeout and set the EAP state machine to success state.

Signed-off-by: Avraham Stern <avraham.stern@intel.com>
2018-02-17 18:45:26 +02:00
Arkadiusz Drabczyk
14dcb22a5b wpa_passphrase: Include $(LIBS) for linking
wpa_passphrase requires libcrypto from OpenSSL (or another selected
library). User can set an alternative path to OpenSSL libraries by
defining LIBS at the top of .config but if $(LIBS) is not actually used
wrong libcrypto is used or compilation fails if there is no libcrypto in
the default locations cc is looking for it. It's especially bad for
cross-compilers that fail with 'cannot find -lcrypto' message.

Signed-off-by: Arkadiusz Drabczyk <arkadiusz@drabczyk.org>
2018-02-17 18:11:40 +02:00
Jouni Malinen
4b07484c3d DPP: Do not include common/dpp.h without CONFIG_DPP=y
This header file pulls in an OpenSSL header file and as such, should not
be included without CONFIG_DPP=y to avoid bringing in an unnecessary
build dependency on OpenSSL header files.

Signed-off-by: Jouni Malinen <j@w1.fi>
2018-02-17 18:07:43 +02:00
Jouni Malinen
6e3726c09e Fix a typo in disassoc_low_ack documentation
Signed-off-by: Jouni Malinen <j@w1.fi>
2018-02-17 17:59:27 +02:00
Danilo Ravotto
19e20c14fb Add ap_isolate configuration option for wpa_supplicant AP mode
Allow client isolation to be configured with ap_isolate inside
wpa_supplicant configuration file.

Signed-off-by: Danilo Ravotto <danilo.ravotto@zirak.it>
2018-02-17 17:48:31 +02:00
Jouni Malinen
aca4d84e3d DPP: Use wildcard BSSID in GAS query frames
Force use of the wildcard BSSID address in GAS query frames with DPP
regardless of how the gas_address3 configuration parameter is set. DPP
specification mandates this and the use of GAS here is really outside
the context of a BSS, so using the wildcard BSSID makes sense even for
the corner case of Configurator running on a known AP (where IEEE 802.11
standard would allow the BSSID of the AP to be used).

Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
2018-02-10 12:42:00 +02:00
Jouni Malinen
6a252ece24 DPP: Fix GAS query removal race condition on DPP_STOP_LISTEN
If a DPP_STOP_LISTEN call happens to be received when there is a pending
gas-query radio work that has not yet been started, it was possible for
gas_query_stop() to go through gas_query_done() processing with
gas->work == NULL and that ended up with the pending GAS query getting
freed without removing the pending radio work that hold a reference to
the now freed memory. Fix this by removing the pending non-started radio
work for the GAS query in this specific corner case.

Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
2018-02-07 18:03:58 +02:00
Jouni Malinen
3b50f8a460 DPP: PKEX initiation on other bands
Add support for wpa_supplicant to try to initiate PKEX on 5 GHz and 60
GHz bands in addition to the previously available 2.4 GHz case. If no
response from a peer device is seen on the 2.4 GHz band (channel 6) for
the five attempts, try the other PKEX channels (5 GHz channels 44 and
149; and 60 GHz channel 2) if they are supported and allowed for
initiating radiation.

Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
2018-02-07 16:56:43 +02:00
Jouni Malinen
70e1901371 DPP: Require use of PMF for DPP AKM
Previously, wpa_supplicant set PMF as optional for the DPP AKM since
there was no clear statement about this requirement in the tech spec.
Now that this requirement has been added, update the implementation to
match. In addition, set ssid->ieee80211w using the actual enum
mfp_options values instead of magic constants to make this a bit more
readable.

Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
2018-02-06 22:08:21 +02:00
Jouni Malinen
3bd35b6816 wpa_supplicant: Fix parsing errors on additional config file
If the -I<config> argument is used and the referenced configuration file
cannot be parsed, wpa_config_read() ended up freeing the main
configuration data structure and that resulted in use of freed memory in
such an error case. Fix this by not freeing the main config data and
handling the error case in the caller.

Signed-off-by: Jouni Malinen <j@w1.fi>
2018-02-04 12:20:13 +02:00