While this is not strictly speaking required based on dynamic
configuration (i.e., dot11ShortPreambleOptionImplemented is static
value based on implementation, not runtime configuration), it is better
to follow local configuration parameter for short preamble in addition
to the associated station capabilities.
This function is not really needed in case of drivers that build the
HT IEs internally. However, since this can get called if ieee80211n=1
is set in hostapd.conf, we better not segfault even if the driver
does not provide hw info (hapd->iface->current_mode == NULL).
Commit 5a1cc30f1a added code that was
assuming CONFIG_WPS_UPNP is enabled whenever CONFIG_WPS is. Fix this
by making the UPnP calls conditional on CONFIG_WPS_UPNP define.
Verify that the driver wrapper is using a valid deauth/disassoc
event before dereferencing the addr pointer. The address is required
to be set in AP mode, but it is safer to verify this here than to
trust on all driver wrappers doing the correct thing.
Prior to commit 6195adda9b the sm->user
dereference did not exist here. While this is in practice non-NULL,
better use more defensive construction here to avoid NULL pointer
dereference should this ever change.
Some NDIS drivers require a workaround to allow them to associate
with a WPS AP that is already using protection (Privacy field = 1).
Let driver_ndis.c know if the AP is already using Privacy and if so,
configure a dummy WEP key to force the driver to associate.
When using overlapped write, we must have the provided memory
areas available during the operation and cannot just use stack
unless we wait for the completion within the function. In the case
of TX here, we can easily wait for the completion since it is likely
to happen immediately. In addition, this provides more reliable
success/failure return value for l2_packet_send(). [Bug 328]
hostapd simply used its own STBC configuration in the STA's HT caps. This
resulted in TX STBC being used for STAs not supporting RX STBC, which in
turn resulted in the STA not receiving anything.
Fix this by handling the STBC flags in the same way mac80211 does. Mask
out RX STBC if we don't support TX STBC and vice versa.
Tested only with the nl80211 driver and a STBC incapable STA.
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Commit d8d940b746 broke the logic on
iterating through all configured network blocks. This was supposed
to continue the loop on mismatch to allow other than the first
configured network to be found.
This patch adds support for wired IEEE 802.1X client on the Solaris.
I have tested with these:
OS : OpenSolaris 2009.06
EAP : EAP-MD5
Switch : Cisco Catalyst 2950
The driver is likely to indicate an immediate signal event when the
threshold value is configured. Since we do this immediately after
association, there is not much point in requesting a new scan to be
started based on this event.
The driver is likely to indicate an immediate signal event when the
threshold value is configured. Since we do this immediately after
association, there is not much point in requesting a new scan to be
started based on this event.
This removes quite a bit of duplicated code and allows network block
priority configuration to be used to prefer unprotected networks and
also allows use on open network with good signal strength even if
scan results show a protected network with marginal signal strength
that does not allow it to be used.
The arithmetic on void pointer exists in trace routine. On GNU C, it
works because void pointer size is 1, but not all compilers behave like
this. So this patch specifies the size of the pointer.
There is no need to process the public key and generate keys if
the AP is going to reject this M2 anyway. This limits effect of
potential CPU DoS attacks in cases where AP PIN is disabled.
A new hostapd_cli command, wps_ap_pin, can now be used to manage
AP PIN at runtime. This can be used to generate a random AP PIN and
to only enable the AP PIN for short period (e.g., based on user
action on the AP device). Use of random AP PIN that is only enabled
for short duration is highly recommended to avoid security issues
with a static AP PIN.
As a compromise between usability and security, do not disable
AP PIN permanently based on failed PIN validations. Instead, go to
AP Setup Locked state for increasing amount of time between each
failure to slow down brute force attacks against the AP PIN.
This avoids problems with some external Registrars that may try
to use the same PIN multiple times without user input. Now, the
user will still be able to fix the PIN and try again later while
a real attack is delayed enough to make it impractical.
This can happen on the AP if the AP PIN is not configured and
the client tries to go through the protocol instead of just using
Registrar mode to receive M1 from the AP. It is cleaner to send
out the WSC_NACK instead of just stopping the protocol.
The wpa_supplicant compilation without CONFIG_WPS option results in
messages below.
scan.c: In function 'wpa_supplicant_scan':
scan.c:246: warning: unused variable 'wps'
This trivial patch erases this warning.
This indicates that the peer identity is associated with the
credential and will be required to match with the identity used
during authentication when the PAC is used (RFC 5422, 4.2.4).
This clears up authentication state in the driver and in case of
cfg80211, unlocks the BSS entry for the previously used AP. The
previous commit cf4783e35f changed
only the ctrl_iface DISCONNECT command behavior; this new commit
does the same for D-Bus commands.
wpa_s->bssid is already cleared by mark_disassoc() when we're getting the
disassociation event for the case where wpa_supplicant requested
disassociation. wpa_s->sme.prev_bssid holds the BSSID we need to check
for, so use that instead.
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
When passing several authentication algorithms through auth_alg, we
should try all of them when the first one fails. The wext driver goes
through the connect nl80211 command and the retries are then handled by
the kernel. The nl80211 doesn't and we have to handle that from
userspace.
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
DEAUTH messages can come from a number of different sources. The one
that's hurting us currently is DEAUTH netlink messages coming to us
from compat-wireless in response to local_state_change DEAUTH messages
we sent as a part of cleaning up state in driver_nl80211's
clear_state_mismatch() function. However, DEAUTH messages can come
from a variety of unwanted sources, including directed denial-of-service
attacks (although MAC verification doesn't place that high a barrier),
so this validation is actually generically useful, I think.
The downside to this method is that without a kernel based approach
"iw dev wlan0 link" no longer works correctly after clear_state_mismatch()
is done. This will be pursued with the kernel folks.
cfg80211/mac80211 seems to be unwilling to change interface mode in
some cases. Make these less likely to cause problems by trying the
changes up to 10 times with 100 msec intervals.
In theory, this should not really be needed, but Windows 7 uses
Registrar mode to probe AP's WPS capabilities before trying to use
Enrollee and fails if the AP does not allow that probing to happen.
This allows the AP to start as an Enrollee and send M1, but refuse
to continue beyond that (M3 will not be sent if AP PIN is not known).
This makes it easier (and a bit faster) to handle multiple local
radios with FT. There is no need to depend on l2_packet in that
case since the frame can be delivered as a direct function call.
