Commit graph

347 commits

Author SHA1 Message Date
Lior David
ba307f8528 P2P: Add a separate pointer to the P2P Device instance
In many places in the code there was a reference to wpa_s->parent to get
from group interface to p2p_dev interface. These places can break if
P2P_DEVICE interface would need to be used with the primary interface as
the group interface, since the parent of the primary interface points to
itself and not the p2p_dev interface.

Fix this by adding a separate "p2pdev" pointer to wpa_supplicant,
it will be the same as parent pointer in most cases but whenever
the primary interface is used as a group interface, change it to
point to the correct p2p_dev interface.

Signed-off-by: Lior David <qca_liord@qca.qualcomm.com>
2016-02-27 19:37:19 +02:00
Jouni Malinen
0645492e7c WNM: Optimize a single BSS transition management candidate scan
If the BSS Transition Management Request frame includes only a single
candidate and we need to scan for the BSS to get up-to-date information,
use a scan for the known BSSID instead of wildcard BSSID. In addition,
set the SSID in the scan if it is known based on old scan results in the
BSS table. This removes unnecessary Probe Response frames when we are
interested in results from only a single BSS.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2016-02-26 17:19:20 +02:00
Avraham Stern
016082e9e6 MBO: Send WNM-Notification when cellular capabilities change
Send a WNM-Notification to the associated AP to indicate changes in
cellular data capabilities.

Signed-off-by: Avraham Stern <avraham.stern@intel.com>
2016-02-22 19:53:04 +02:00
Avraham Stern
84d1c0fd5a WNM: Add candidate list to BSS transition response
Add the transition candidate list to BSS Transition Management Response
frame. The candidates preference is set using the regular wpa_supplicant
BSS selection logic. If the BSS transition request is rejected and
updated scan results are not available, the list is not added.

Signed-off-by: Avraham Stern <avraham.stern@intel.com>
2016-02-22 19:53:04 +02:00
Avraham Stern
c8082d2b6a MBO: Add MBO IE to BSS Transition Management Response frame
When rejecting a BSS Transition Management Request frame, add MBO IE to
the BSS Transition Management Response frame to specify the transition
rejection reason.

Signed-off-by: David Spinadel <david.spinadel@intel.com>
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
2016-02-22 19:53:04 +02:00
Avraham Stern
dd5999084e MBO: Parse MBO IE in BSS Transition Management Request frames
Add parsing of MBO IE in BSS Transition Management Request frames. If
the MBO IE includes the association retry delay attribute, do not try to
reconnect to the current BSS until the delay time is over.

If the MBO IE includes the cellular data connection preference attribute
or the transition rejection reason attribute, send a message to upper
layers with the data.

Signed-off-by: David Spinadel <david.spinadel@intel.com>
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
2016-02-22 19:53:04 +02:00
Avraham Stern
5e57ba2505 MBO: Add Supported Operating Classes element to Association Request
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
2016-02-22 19:53:04 +02:00
David Spinadel
cb06cf3456 MBO: Prevent association to APs that explicitly disallow this
Prevent association to MBO APs that have association disallowed
attribute in MBO IE in Beacon or Probe Response frames.

Signed-off-by: David Spinadel <david.spinadel@intel.com>
2016-02-22 19:53:04 +02:00
David Spinadel
c5d193d7b3 MBO: Add cellular capability to MBO IE
Add cellular capability attribute to MBO IE and add MBO IE with cellular
capabilities to Probe Request frames. By default, cellular capability
value is set to Not Cellular capable (3).

Signed-off-by: David Spinadel <david.spinadel@intel.com>
2016-02-22 19:53:04 +02:00
David Spinadel
2d5b8614b7 MBO: Send MBO WNM-Notification Request frames to notify changes
Send a WNM-Notification Request frame with Non-preferred Channel Report
subelement if the non-preferred channels list changes during an
association.

Signed-off-by: David Spinadel <david.spinadel@intel.com>
2016-02-22 19:53:04 +02:00
David Spinadel
92c6e2e3a9 MBO: Implement MBO non-preferred channel report in Association Request
Add MBO IE with non-preferred channels to (Re)Association Request
frames.

Signed-off-by: David Spinadel <david.spinadel@intel.com>
2016-02-22 19:53:04 +02:00
Avraham Stern
ea69d9737c wpa_supplicant: Share a single get_mode() implementation
There is no need to duplicate this helper function in multiple files.

Signed-off-by: Avraham Stern <avraham.stern@intel.com>
2016-02-21 17:14:51 +02:00
Jouni Malinen
ca9968a012 HS 2.0: Convert icon storage to use dl_list
This simplifies the list operations quite a bit.

Signed-off-by: Jouni Malinen <j@w1.fi>
2015-12-19 18:49:57 +02:00
Jan Nordqvist
8dd5c1b4e9 HS 2.0: Add a command to retrieve icon with in-memory storage
This adds a new command based Hotspot 2.0 icon retrieval option.

In short, here is the new command sequence:
1. REQ_HS20_ICON <bssid> <file-name>
2. event: RX-HS20-ICON <bssid> <file-name> <size>
3. GET_HS20_ICON <bssid> <file-name> <offset> <size>
   (if needed, repeat with larger offset values until full icon is
   fetched)
5. DEL_HS20_ICON <bssid> <file-name>

REQ_HS20_ICON is a new command that is analogous to HS20_ICON_REQUEST
with the slight difference that an entry to store the icon in memory is
prepared. The RX-HS20-ICON event has been augmented with BSSID,
file-name and size, and GET_HS20_ICON is used to retrieve a chunk of up
to <size> bytes of icon data at offset <offset>. Each chunk is returned
as a base64 encoded fragment, preceded by "HS20-ICON-DATA", BSSID, and
file-name as well as the starting offset of the data.

If there is no entry prepared for the icon when the ANQP result comes
back, hs20_process_icon_binary_file falls back to legacy behavior.

Finally the DEL_HS20_ICON command deletes (all) icons associated with
BSSID and file-name (there could be several if retries are used and they
have different dialog tokens).

Signed-off-by: Jan Nordqvist <jannq@google.com>
2015-12-19 18:34:01 +02:00
Avichal Agarwal
af041f997d dbus: Add support for vendor specific elements
The new methods are
1. VendorElemAdd "i" "ay" i=integer ay=array of bytes
2. VendorElemGet "i" i=integer (output array of bytes)
3. VendorElemRem "i" "ay" i=integer ay=array of bytes

These provide functionality similar to the control interface commands
VENDOR_ELEM_ADD, VENDOR_ELEM_GET, and VENDOR_ELEM_REMOVE.

Signed-off-by: Avichal Agarwal <avichal.a@samsung.com>
Signed-off-by: Purushottam Kushwaha <p.kushwaha@samsung.com>
Signed-off-by: Kyeong-Chae Lim <kcya.lim@samsung.com>
Signed-off-by: Mayank Haarit <mayank.h@samsung.com>
Signed-off-by: Dilshad Ahmad <dilshad.a@samsung.com>
[VendorElemGet to return array of bytes instead of string; cleanup]
Signed-off-by: Jouni Malinen <j@w1.fi>
2015-12-06 12:50:13 +02:00
Avraham Stern
32c02261dd Add support for configuring scheduled scan plans
Add the option to configure scheduled scan plans in the config file.
Each scan plan specifies the interval between scans and the number
of scan iterations. The last plan will run infinitely and thus
specifies only the interval between scan iterations.

usage:
sched_scan_plans=<interval:iterations> <interval2:iterations2> ... <interval>

Signed-off-by: Avraham Stern <avraham.stern@intel.com>
2015-11-30 14:03:28 +02:00
Ahmad Kholaif
c27f4c9006 P2P: Add support for VHT 80+80 MHz and 160 MHz
The new max_oper_chwidth and freq2 arguments to P2P_CONNECT, P2P_INVITE,
and P2P_GROUP_ADD control interface commands can be used to request
larger VHT operating channel bandwidth to be used than the previously
used maximum 80 MHz.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2015-11-25 19:01:20 +02:00
Ilan Peer
ed7820b484 P2P: Add a testing option to force P2P GO CSA
Add a testing option to force a P2P GO CSA on successful
invitation to join an active P2P GO.

Signed-off-by: Ilan Peer <ilan.peer@intel.com>
2015-11-22 21:49:19 +02:00
Peter Oh
a65efbfb24 Add VHT support for Mesh
Mesh Points themselves have capability to support VHT as long as
hardware supports it. However, supporting VHT in mesh mode was disabled
because no one had clearly tested and confirmed its functionality. Since
VHT80 has now been verified to work with ath10k QCA988X driver and
mac80211_hwsim, enable VHT support in mesh mode.

Signed-off-by: Peter Oh <poh@qca.qualcomm.com>
2015-11-19 11:37:41 +02:00
Jouni Malinen
03ed0a5239 WNM: Ignore WNM-Sleep Mode Response if WNM-Sleep Mode has not been used
The AP is not expected to send out a WNM-Sleep Mode Response frame
without the STA trying to use WNM-Sleep Mode. Drop such unexpected
responses to reduce unnecessary processing of the frame.

Signed-off-by: Jouni Malinen <j@w1.fi>
2015-11-10 18:40:54 +02:00
Ilan Peer
8bb8e6edb8 P2PS: Indicate the chosen operating frequency
On successful P2P PD, report the chosen frequency in case the local
device is going to be the P2P GO, so in can later be used to instantiate
the new P2P GO, etc.

Signed-off-by: Ilan Peer <ilan.peer@intel.com>
2015-10-11 21:42:03 +03:00
Kanchanapally, Vidyullatha
e903d32d41 Parallelize distinct radio work operations
This commit contains the necessary changes to parallelize
distinct radio work operations which are different in type and
the band used, only when the underlying driver is capable of
supporting such simultaneous offchannel operations.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2015-10-01 01:41:46 +03:00
Jouni Malinen
dfaf11d648 P2P: Require fresh scan results for persistent group re-invocation
The P2P group is not yet operating when going through invitation
exchange for re-invocation. Previously, an old cached scan result could
be used to skip the scan immediately after the invitation exchange.
While this may result in the fastest possible connection, it does have
some issues with cases where the GO takes some time to start up. It
would also be at least theoretically possible for some of the BSS
parameters to be different, so having a fresh scan result from the new
GO instance may be desired in any case.

Add a mechanism to skip scan results that have been last updated before
a specific point in time and as the first user for this mechanism,
require chan results to be more recent than the invitation message
exchange for the P2P Client role in persistent group re-invocation case.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2015-08-22 00:22:12 +03:00
Andrei Otcheretianski
b9da88d6c1 P2PS: Authorize any peer for P2PS method if interface address not known
When P2PS PD with default P2PS method is done, the peer that becomes GO
should authorize the client. However, P2PS specification doesn't require
the client to include its intended interface address in PD
Request/Response. As a result, the P2P Client's interface address may not
be known and any address may need to be authorized.

Previously, client's P2P Device Address was used for authorization,
which is not correct when a dedicated interface is used for P2P Client.
This is not resulting in a connection failure, however it causes a
significant delay (until WPS_PIN_TIME_IGNORE_SEL_REG elapses). Fix this
by authorizing the intended interface address, if known; or any address,
if not known.

Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
2015-08-06 20:45:15 +03:00
Jouni Malinen
84bcb4e7a9 FST: Mark fst_ies buffer const
This buffer is owned by the FST module, so mark it const in the
set_ies() callback to make it clearer which component is responsible for
modifying and freeing this.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2015-08-03 17:40:30 +03:00
Gautam
d4e597959c P2P: Fix P2P configuration file name
The P2P configuration file is wrongly set as STA configuration file,
even though a separate configuration file is mentioned with '-m' option.
Add initialization and deallocation of global.params->conf_p2p_dev to
fix this.

Signed-off-by: Gautam <gautams@broadcom.com>
2015-08-02 21:37:09 +03:00
Srinivas Dasari
844dfeb804 QCA vendor command support to set band to driver
Add vendor command to pass SET setband command to the driver and read
the updated channel list from driver when this notification succeeds.
This allows the driver to update its internal channel lists based on
setband configuration.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2015-07-28 21:00:18 +03:00
Anton Nayshtut
b36a3a65aa FST: Integration into wpa_supplicant
This commit integrates the FST into the wpa_supplicant.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2015-07-16 18:26:15 +03:00
Ilan Peer
f43c1ae798 P2P: Handle P2P Device dedicated interface parent removal
In case of a network interface removal, check if the interface
was also the parent interface of the P2P Device dedicated interface.
If this is the case, then stop the P2P Device functionality, and
remove the P2P Device dedicated interface.

In case that the interface is added again and P2P Device
functionality can be enabled again, add a new P2P Device dedicated
interface and allow further P2P Device functionality.

In case that the P2P Device dedicated interface is re-created, the
original P2P Device configuration file is needed, so store it in
the global params (instead in the wpa_interface configuration).

Signed-off-by: Ilan Peer <ilan.peer@intel.com>
2015-06-19 16:22:26 +03:00
Avraham Stern
e1dffa3b2c P2P: Fix PBC overlap detection
PBC overlap detection searches for another BSS with active PBC in the
BSS table. However, when a separate P2P interface is used, scan results
without P2P IE are not saved in the BSS table, so non-P2P BSS's with
active PBC will not be detected.

Fix this by iterating only the WPS AP array instead of the BSS table.
This is also more efficient since only WPS APs may have active PBC. This
also fixes hwsim test "grpform_pbc_overlap" when a dedicated P2P Device
is used.

Signed-off-by: Avraham Stern <avraham.stern@intel.com>
2015-06-19 11:25:21 +03:00
Max Stepanov
07c1e987d5 P2PS: Enable Probe Request frame processing by P2P Client
1. Add global p2p_cli_probe property to enable/disable Probe Request
frame RX reporting for connected P2P Clients. The property can be set to
0 - disable or 1 - enable. The default value is 0.

2. Enable Probe Request frame RX reporting for P2P Client on
WPA_COMPLETED state if p2p_cli_probe property is set to 1. Disable it
when an interface state is changing to any other state.

3. Don't cancel Probe Request frame RX reporting on wpa_stop_listen for
a connected P2P Client handling Probe Request frames.

Signed-off-by: Max Stepanov <Max.Stepanov@intel.com>
Reviewed-by: Ilan Peer <ilan.peer@intel.com>
2015-06-14 23:16:55 +03:00
Krishna Vamsi
a80651d067 Add support to request a scan with specific SSIDs
Support a request to scan specific SSIDs given by user with the SCAN
command. The SSID list can be suffixed to the scan command as follows.
For example, if SSIDs "ABC" and "abc123" need to be specifically
scanned, the command should be "SCAN ssid 414243 ssid 616263313233". The
value of the SSID is passed in hexadecimal representation.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2015-06-05 15:55:26 +03:00
Ilan Peer
b4342ca4d8 P2P: Use p2p_init_wpa_s for P2P command redirection over D-Bus
D-Bus used the p2p_dev member in struct wpa_supplicant to track the
interface used for P2P Device operations. However, this is not needed as
the interface used for P2P Device operations is stored in struct
wpa_global->p2p_init_wpa_s.

Replace all the redirections to wpa_s->p2p_dev with redirections to
wpa_s->global->p2p_init_wpa_s and removed this member as it is no
longer needed.

Signed-off-by: Ilan Peer <ilan.peer@intel.com>
2015-05-25 18:31:09 +03:00
Jouni Malinen
5aeebc48e8 D-Bus Fix network_is_persistent_group() for P2P operations
Commit c2762e410f ('P2P: Update D-Bus
network object semantics during group formation') added this helper
function to determine whether a network block is used for storing a
persistent group information. However, it implemented this in a way that
matches both persistent group storage and an operating persist group
instance. This does not seem to match the expected behavior for the
D-Bus objects, so fix this to match only the persistent group storage
case to avoid registering/unregistered incorrect D-Bus objects for
groups.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2015-04-29 20:52:22 +03:00
Mikael Kanstrup
8b423edbd3 Declare all read only data structures as const
By analysing objdump output some read only structures were found in
.data section. To help compiler further optimize code declare these
as const.

Signed-off-by: Mikael Kanstrup <mikael.kanstrup@sonymobile.com>
2015-04-25 17:33:06 +03:00
Hu Wang
e7d20342b5 WPS: Enforce five second minimum time before AP iteration
Previously, wpa_supplicant was using number of scan iterations
(WPS_PIN_SCAN_IGNORE_SEL_REG = 3) to give some time for finding a WPS AP
with Selected Registrar TRUE before starting to iterate through all WPS
APs. While this works fine in most cases, some drivers may return the
initial three scan results so quickly that the total amount of time is
only couple of seconds in case none of the APs are initially advertising
Selected Registrar TRUE. To give some more time for APs (WPS Registrars)
to become ready, add an additional constraint on the iteration based on
time (WPS_PIN_TIME_IGNORE_SEL_REG = 5 seconds).

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2015-04-24 17:55:32 +03:00
Jouni Malinen
d9d1b9527a Use SSID_MAX_LEN define instead of value 32 when comparing SSID length
This makes the implementation easier to understand.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2015-04-22 11:44:18 +03:00
Jithu Jance
efa232f915 Add support for virtual interface creation/deletion
Extend interface_add and interface_remove commands via an optional
argument to allow wpa_supplicant to create/delete a new virtual
interface.

Signed-off-by: Jithu Jance <jithu@broadcom.com>
2015-03-26 22:20:35 +02:00
Avraham Stern
9bd566a33a Delay AP selection if all networks are temporarily disabled
If all networks are temporarily disabled, delay AP selection until at
least one network is enabled. Running AP selection when all networks are
disabled is useless as wpa_supplicant will not try to connect. In
addition, it will result in needless scan iterations that may delay the
connection when it is needed.

Signed-off-by: Avraham Stern <avraham.stern@intel.com>
2015-03-22 20:53:58 +02:00
Jouni Malinen
1772d348ea P2P: Fix interface deinit for failed group interface initialization
wpa_supplicant_deinit_iface() ends up removing all P2P groups if the
removed interface is the parent interface. This is correct behavior in
general, but this resulted in issues in the new group interface
initialization error path since wpa_s->parent was not assigned before
hitting this check. Fix this by assigning wpa_s->parent as part of
wpa_supplicant_add_iface().

Signed-off-by: Jouni Malinen <j@w1.fi>
2015-03-01 22:36:53 +02:00
Jouni Malinen
c28059091a Do not add blacklist entries based on normal disconnect request cases
There are number of cases where wpa_supplicant requests the current
connection to be disconnected before starting a new operation. Such
cases do not really indicate that there was an error in connecting or a
disconnection initiated by the AP, so do not add a temporary blacklist
entry in such sequences.

Signed-off-by: Jouni Malinen <j@w1.fi>
2015-03-01 15:54:24 +02:00
Jouni Malinen
a1b790eb9d Select AP based on estimated maximum throughput
This modifies the BSS selection routines to calculate SNR and estimated
throughput for each scan result and then use the estimated throughput as
a criteria for sorting the results. This extends the earlier design by
taking into account higher throughput rates if both the AP and local
device supports HT20, HT40, or VHT80. In addition, the maximum rate is
restricted based on SNR.

In practice, this gives significantly higher probability of selecting
HT/VHT APs when there are multiple BSSes in the same ESS and SNR is not
low enough to prevent higher MCS use.

Signed-off-by: Jouni Malinen <j@w1.fi>
2015-02-22 11:09:54 +02:00
Masashi Honma
bf51f4f82b mesh: Fix remaining BLOCKED state after SAE auth failure
When SAE authentication fails, wpa_supplicant retries four times. If all
the retries result in failure, SAE state machine enters BLOCKED state.
Once it enters this state, wpa_supplicant doesn't retry connection. This
commit allow connection retries even if the state machine entered
BLOCKED state.

There could be an opinion "Is this patch needed? User could know the SAE
state machine is in the BLOCKED mode by MESH-SAE-AUTH-BLOCKED event.
Then user can retry connection. By user action, SAE state machine can
change the state from BLOCKED to another.". Yes, this is a true at the
joining mesh STA. However, a STA that is already a member of existing
mesh BSS should not retry connection because if the joining mesh STA
used wrong password, all the existing STA should do something from UI to
retry connection.

Signed-off-by: Masashi Honma <masashi.honma@gmail.com>
2015-02-08 12:43:24 +02:00
Krishna Vamsi
93eca6155b P2PS: Do not remove pending interface on p2p_stop_find
The pending interface created during provision discovery should
not be removed on stopping p2p_find. This pending interface has
to be used after completing GO negotiation. Earlier the pending
interface is created just before GO negotiation so there was no
problem.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2015-02-03 01:35:07 +02:00
Krishna Vamsi
306aaf49f8 P2PS: Start WPS registrar upon GO formation
If P2PS config method is used for provisioning, upon forming a new GO,
start WPS registrar for the provisioned peer automatically.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2015-02-03 01:35:07 +02:00
Krishna Vamsi
9a58e521ac P2PS: Callback to create pending group after sending PD Response
This introduces a P2P module callback function that will be used to
create the pending P2PS group after sending PD Response and receiving
ACK status for it.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2015-02-03 01:35:07 +02:00
Krishna Vamsi
6d9085145c P2PS: Process P2PS provisioning commands
This extends wpas_p2p_prov_disc() implementation to accept P2PS
parameters. None of the callers are yet using this functionality; the
following commit introduces a user.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2015-02-03 01:35:07 +02:00
Jouni Malinen
3f56a2b746 Ignore pmf=1 default if driver does not support PMF
Connection with a PMF enabled AP will fail if we try to negotiate PMF
while the local driver does not support this. Since pmf=1 does not
require PMF for a successful connection, it can be ignored in such a
case to avoid connectivity issues with invalid configuration. This makes
it somewhat easier to allow upper layer programs to use pmf=1 default
regardless of driver capabilities.

Signed-off-by: Jouni Malinen <j@w1.fi>
2015-01-27 12:38:52 +02:00
Ben Rosenfeld
d90bfa97f4 Move external_scan_running to wpa_radio
external_scan_running should be common to all interfaces that share a
radio. This fixes a case where external_scan_running was set on a single
interface, but did not block scan on other interfaces.

Signed-off-by: Ben Rosenfeld <ben.rosenfeld@intel.com>
2015-01-20 01:57:59 +02:00
Jouni Malinen
2d9c99e37b Retry scan-for-connect if driver trigger fails
This restores some of the pre-radio work behavior for scanning by
retrying scan trigger if the driver rejects it (most likely returning
EBUSY in case of nl80211-drivers). Retry is indicated in the
CTRL-EVENT-SCAN-FAILED event with "retry=1".

For manual scans (e.g., triggered through "SCAN" control interface
command), no additional retries are performed. In other words, if upper
layers want to retry, they can do so based on the CTRL-EVENT-SCAN-FAILED
event.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2015-01-19 20:25:20 +02:00