This increases wpa_supplicant_ie_txt(), print_bss_info(), and
wpa_supplicant_ctrl_iface_scan_result() testing coverage to include the
previously missing key management options.
Signed-off-by: Jouni Malinen <j@w1.fi>
This verifies that IBSS_RSN <peer> return OK for the case where a valid
and already connection peer address is given.
Signed-off-by: Jouni Malinen <j@w1.fi>
There is no need to pass the test case names to the VMs when using
parallel-vm.py. Removing those from the command line helps in avoiding
kernel panic if maximum number of kernel parameters limit is hit.
Signed-off-by: Jouni Malinen <j@w1.fi>
Use single channel scan instead of full scan to save time. In addition,
use EAP-GPSK which takes significantly less CPU that EAP-EKE with
default parameters.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This tests RP EAP-Initiate/Re-auth-Start transmission, ERP key
derivation, and EAP-Initiate/Re-auth + EAP-Finish/Re-auth exchange and
rMSK derivation.
Signed-off-by: Jouni Malinen <j@w1.fi>
It was apparently possible for this test case not to do what it was
supposed to do, i.e., get nl80211 Authenticate command failing due to
cfg80211 BS entry missing. With the external radio work blocking fixed,
this can be cleaned up by explicitly waiting for the scan event. In
addition, a less used channel can be selected to avoid finding other BSS
entries.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This makes it more convenient and consistent to clear the cached scan
results from cfg80211 and wpa_supplicant.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Do not leave the station trying to connect at the end of the test case
since that can have an effect to the following test case. Such sequences
should be tested in test cases that are specifically designed for that
rather than randomly between test cases.
Signed-off-by: Jouni Malinen <j@w1.fi>
Since run-tests.py is now required to run as root, there is no need to
use the somewhat awkward "sudo tee" construction; instead, just write
directly to the file.
Signed-off-by: Jouni Malinen <j@w1.fi>
Clear scan results to avoid PBC overlap issues caused by earlier test
cases. For example, go_neg_with_bss_connected followed by
go_neg_with_bss_on_disallowed_chan resulted in failure before this
change.
Signed-off-by: Jouni Malinen <j@w1.fi>
This test case was failing every now and then due to dev1
(no_auto_peer=1) not receiving the new-peer-candidate event in time
before dev0 has already stopped retries on mesh peering open message.
This sounds somewhat expected with the default 4 * 40 ms = 160 ms
retries and 1000 TU beacon interval. Use maximum timeout 16 * 255 ms =
4080 ms to make this test case less likely to fail.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Both the wpa_supplicant and kernel configuration need wext to
run the wext testcase, enable those in the default/example
configurations.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Keep full channel scans in autogo for test coverage, but use single
channel scan in all other autogo* test cases to remove unnecessary
waiting that does not add any test coverage. This removes more than one
minute from the total test execution time.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Replace fixed sleep with waiting for a disconnection event. In addition,
remove unnecessary use of sudo.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
It was possible for this test case to fail due to PBC overlap that was
detected based on previous test case having used PBC. Make that false
positive less likely to happen by explicitly clearing the scan cache on
the device.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
p2p_oper_reg_class and p2p_oper_channel need to be restored to 0, not an
arbitrary 2.4 GHz channel to avoid issues for following test cases. For
example, p2p_channel_random_social_with_op_class_change followed by
p2p_autogo_pref_chan_not_in_regulatory ended up with the latter test
case failing.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
hwsim_utils.test_connectivity() is already bidirectional test, so there
is no need to run it twice with the devices swapped for the second
iteration.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Clear wpa_supplicant and cfg80211 scan results at the end of hidden SSID
test cases to avoid potential issues for following test cases. For
example, ap_hs20_session_info could fail if executed immediately after
ssid_hidden due to the AP configuration change from open to RSN was not
noticed.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This is more robust and extensible than configuring IPv6 addresses on
the interfaces and trying to use ping6 or some other external tools to
generate suitable IPv6 frames.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
The 50 ms wait time for Action frame response was not sufficient when
the tests are run under heavy load (e.g., multiple VMs in parallel).
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Wait for GO to start before sending invitation frames in the protocol
test. Without this, it was possible to hit the 5 second timeout on
management frame RX under load.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
It was possible for this test case to fail due to PBC overlap that was
detected based on previous test case having used PBC. Make that false
positive less likely to happen by explicitly clearing the scan cache on
the devices.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
The "Not fully connected" report did not clearly identify what went
wrong, so make this more verbose in hope of being able to determine what
happened should this test case fail again.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
It was possible to hit the 10 second timeout in some test cases under
heavy load (e.g., with large number of VMs running tests in parallel).
These timeouts are not really indicating any real error, so make them
less likely to show up in reports by increasing the connection timeout
to 30 seconds.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
There are valid status (and possibly status-driver) responses
that don't have a name=value format, ignore those in the test
framework parser.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
