Commit graph

108 commits

Author SHA1 Message Date
Sabrina Dubroca
23c3528a84 mka: Add support for removing SAs
So that the core can notify drivers that need to perform some operations
when an SA is deleted.

Signed-off-by: Sabrina Dubroca <sd@queasysnail.net>
2016-10-29 11:35:38 +03:00
Sabrina Dubroca
6f551abdfc mka: Remove "channel" hacks from the stack and the macsec_qca driver
This is specific to the macsec_qca driver. The core implementation
shouldn't care about this, and only deal with the complete secure
channel, and pass this down to the driver.

Drivers that have such limitations should take care of these in their
->create functions and throw an error.

Since the core MKA no longer saves the channel number, the macsec_qca
driver must be able to recover it. Add a map (which is just an array
since it's quite short) to match SCIs to channel numbers, and lookup
functions that will be called in every place where functions would get
the channel from the core code. Getting an available channel should be
part of channel creation, instead of being a preparation step.

Signed-off-by: Sabrina Dubroca <sd@queasysnail.net>
2016-10-29 11:24:08 +03:00
Sunil Dutt
2e4e4fb71c nl80211: Allow TDLS trigger modes to be configured to the host driver
This commit adds a control interface command to configure the TDLS
trigger mode to the host driver. This TDLS mode is configured through
the "SET tdls_trigger_control" control interface command.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2016-10-27 23:22:33 +03:00
Sabrina Dubroca
a25e4efc9e mka: Add driver op to get macsec capabilities
This also implements the macsec_get_capability for the macsec_qca
driver to maintain the existing behavior.

Signed-off-by: Sabrina Dubroca <sd@queasysnail.net>
2016-10-09 11:30:48 +03:00
Sabrina Dubroca
5f5ca28414 mka: Pass full structures down to macsec drivers' receive SC ops
Clean up the driver interface by passing pointers to struct receive_sc
down the stack to the {create,delete}_recevie_sc() ops, instead of
passing the individual properties of the SC.

Signed-off-by: Sabrina Dubroca <sd@queasysnail.net>
2016-10-08 00:45:19 +03:00
Sabrina Dubroca
8ebfc7c2ba mka: Pass full structures down to macsec drivers' transmit SC ops
Clean up the driver interface by passing pointers to struct transmit_sc
down the stack to the {create,delete}_transmit_sc() ops, instead of
passing the individual arguments.

Signed-off-by: Sabrina Dubroca <sd@queasysnail.net>
2016-10-08 00:45:03 +03:00
Sabrina Dubroca
cecdecdbe8 mka: Pass full structures down to macsec drivers' receive SA ops
Clean up the driver interface by passing pointers to struct receive_sa
down the stack to the {create,enable,disable}_receive_sa() ops, instead
of passing the individual properties of the SA.

Signed-off-by: Sabrina Dubroca <sd@queasysnail.net>
2016-10-03 13:26:26 +03:00
Sabrina Dubroca
909c1b9835 mka: Pass full structures down to macsec drivers' transmit SA ops
Clean up the driver interface by passing pointers to struct transmit_sa
down the stack to the {create,enable,disable}_transmit_sa ops, instead
of passing the individual properties of the SA.

Signed-off-by: Sabrina Dubroca <sd@queasysnail.net>
2016-10-03 13:17:21 +03:00
Sabrina Dubroca
7fa5eff8ab mka: Pass full structures down to macsec drivers' packet number ops
Clean up the driver interface by passing pointers to structs transmit_sa
and receive_sa down the stack to get_receive_lowest_pn(),
get_transmit_next_pn(), and set_transmit_next_pn() ops, instead of
passing the individual arguments.

Signed-off-by: Sabrina Dubroca <sd@queasysnail.net>
2016-10-03 12:54:08 +03:00
Sabrina Dubroca
07a6bfe1d2 mka: Store cipher suite ID in a u64 instead of u8 pointer
Signed-off-by: Sabrina Dubroca <sd@queasysnail.net>
2016-08-28 21:55:54 +03:00
Sabrina Dubroca
ec958aee32 mka: Remove cs_len argument from the set_current_cipher_suite functions
This is a known constant value (CS_ID_LEN, i.e., the length of the EUI64
identifier) and does not need to be provided separately in these
function calls.

Signed-off-by: Sabrina Dubroca <sd@queasysnail.net>
2016-08-28 20:55:34 +03:00
vamsi krishna
cc9985d1b1 Set default scan IEs to the driver (QCA vendor extension)
This makes wpa_supplicant set default scan IEs to the driver (if the
vendor command is supported). The driver can use these IEs in the scan
requests initiated by the driver itself. Also the driver can merge these
IEs into further scan requests that it receives, in case if the scan
request doesn't carry any of the IEs sent in this command.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2016-08-02 21:21:52 +03:00
Peng Xu
a6f5b1937a P2P: Allow P2P listen being offloaded to the driver/firmware
This allows P2P Listen to be offloaded to device to enhance power
saving.

To start P2P listen offload, from wpa_cli interface, issue the command:
	p2p_lo_start <freq> <period> <interval> <count>

To stop P2P listen offload, issue the command:
	p2p_lo_stop

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2016-07-03 22:36:58 +03:00
Jouni Malinen
f868d5607d mesh: Clean up AMPE element encoding and parsing
The AMPE element includes number of optional and variable length fields
and those cannot really be represented by a fixed struct
ieee80211_ampe_ie. Remove the optional fields from the struct and
build/parse these fields separately.

This is also adding support for IGTKdata that was completely missing
from the previous implementation. In addition, Key RSC for MGTK is now
filled in and used when configuring the RX MGTK for a peer.

Signed-off-by: Jouni Malinen <j@w1.fi>
2016-06-19 20:18:09 +03:00
Kanchanapally, Vidyullatha
cc9a2575ca nl80211: Use extended capabilities per interface type
This adds the necessary changes to support extraction and use of the
extended capabilities specified per interface type (a recent
cfg80211/nl80211 extension). If that information is available,
per-interface values will be used to override the global per-radio
value.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2016-05-31 21:35:54 +03:00
Matti Gottlieb
e42adb9a75 driver: Add a packet filtering function declaration
Add a new function declaration that will allow wpa_supplicant to request
the driver to configure data frame filters for specific cases.

Add definitions that will allow frame filtering for stations as
required by Hotspot 2.0:

1. Gratuitous ARP
2. Unsolicited NA
3. Unicast IP packets encrypted with GTK

Signed-off-by: Matti Gottlieb <matti.gottlieb@intel.com>
2016-04-08 13:13:55 +03:00
Avraham Stern
09ea4309b6 nl80211: Add support for multiple scan plans for scheduled scan
Add 'scan plans' to driver scan parameters for scheduled scan.
Each 'scan plan' specifies the number of iterations to run the scan
request and the interval between iterations. When a scan plan
finishes (i.e., it was run for the specified number of iterations),
the next scan plan is executed. The last scan plan will run
infinitely.

The maximum number of supported scan plans, the maximum number of
iterations for a single scan plan and the maximum scan interval
are advertised by the driver.

Signed-off-by: Avraham Stern <avraham.stern@intel.com>
2015-11-30 14:03:28 +02:00
Kanchanapally, Vidyullatha
4f30addb38 nl80211: Add support for aborting an ongoing scan
This adds the driver interface commands for issuing a request to abort
an ongoing scan operation.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2015-11-26 19:44:14 +02:00
Avraham Stern
d8a3b66d7f driver: Make setting up AP optional when creating AP interface
When an AP interface it created, it is also setup and subscribes
for management frames etc. However, when the interface is added by
wpa_supplicant, setting up for AP operations is redundant because
it will be done by wpa_supplicant on wpa_drv_init() when setting
the interface mode to AP.

In addition, it may cause wpa_supplicant to fail initializing the
interface as it will try to subscribe for management frames on this
interface but the interface is already registered.

Change this, so when adding an AP interface, make setting up the AP
optional, and use it only when the interface is added by hostapd but not
when it is added by wpa_supplicant.

Signed-off-by: Avraham Stern <avraham.stern@intel.com>
2015-11-22 17:42:59 +02:00
Andrei Otcheretianski
2d3943ce5b nl80211: Specify CSA offsets in send_mlme() driver op
Some management frames contain CSA counters which should be updated by
kernel. Change driver op send_mlme() allowing to send a frame,
specifying an array of offsets to the CSA counters which should be
updated. For example, CSA offsets parameters should be specified when
sending Probe Response frames during CSA period.

Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
2015-10-03 21:07:35 +03:00
Jouni Malinen
34c5267bbc Return error from wpa_drv_get_pref_freq_list() if no driver support
Commit 983422088f ('nl80211: Add means to
query preferred channels') return success if no driver wrapper callback
was provided for fetching the preferred channel list. That is
problematic since the *num argument is not updated and uninitialized
freq_list could end up getting used with arbitrary frequency values. Fix
this by returning error in case the values were not available due to
driver wrapper not implementing the function. This matches the style
used in the driver_nl80211.c implementation for the case where the
driver does not support such fetch operation.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2015-07-30 22:13:47 +03:00
Ahmad Kholaif
983422088f nl80211: Add means to query preferred channels
Extend the QCA vendor specific nl80211 interface to query the preferred
frequency list from driver and add a new wpa_cli command to query this
information.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2015-07-29 19:46:31 +03:00
Ahmad Kholaif
7c813acf9c P2P: Inform driver of the operating channel following group formation
Upon GO Negotiation completion, if the remote peer becomes GO, send a
hint event over QCA vendor specific interface to inform the driver of
the likely operating channel of the P2P GO.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2015-07-29 19:10:16 +03:00
Srinivas Dasari
844dfeb804 QCA vendor command support to set band to driver
Add vendor command to pass SET setband command to the driver and read
the updated channel list from driver when this notification succeeds.
This allows the driver to update its internal channel lists based on
setband configuration.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2015-07-28 21:00:18 +03:00
Andrei Otcheretianski
0799b3f899 P2P: Specify frequency when sending Probe Response frame
If the RX frequency of the Probe Request frame is known, specify it when
sending the Probe Response frame. This is needed when the Probe Request
frame is received on another virtual interface, for example, when a GO
or P2PS client are discoverable on the group operating channel.

Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
Reviewed-by: Ilan Peer <ilan.peer@intel.com>
2015-06-14 23:16:55 +03:00
Andrei Otcheretianski
5d180a7739 drivers: Add freq parameter to send_mlme() function
Change send_mlme() API to allow sending management frames on a specific
channel, overriding the internal driver decision.

Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
Reviewed-by: Ilan Peer <ilan.peer@intel.com>
2015-06-14 23:16:55 +03:00
Eliad Peller
e7a296ba13 Remove unused shared_freq driver op
This driver op is not used anymore

Signed-off-by: Eliad Peller <eliad@wizery.com>
2015-03-20 15:56:59 +02:00
Jouni Malinen
98cd3d1c3b Preparations for variable length KCK and KEK
This modifies struct wpa_ptk to allow the length of KCK and KEK to be
stored. This is needed to allow longer keys to be used, e.g., with
Suite B 192-bit level.

Signed-off-by: Jouni Malinen <j@w1.fi>
2015-01-27 01:26:49 +02:00
Jouni Malinen
911942ee64 Add a test framework for various wpa_supplicant failure cases
For CONFIG_TESTING_OPTIONS=y builds, add a new test parameter than can
be used to trigger various error cases within wpa_supplicant operations
to make it easier to test error path processing. "SET test_failure
<val>" is used to set which operation fails. For now, 0 = no failures
and 1 = scan trigger fails with EBUSY. More operations can be added in
the future to extend coverage.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2015-01-19 19:34:00 +02:00
Arik Nemtsov
6b90deae4d TDLS: Propagate enable/disable channel-switch commands to driver
The supplicant code does not try to control the actual channel of the
radio at any point. It simply passes the target peer and channel
parameters to the driver. It's the driver's responsibility to
periodically initiate TDLS channel-switch operations when TDLS
channel-switching is enabled.

Allow enable/disable operations to be invoked via the control interface.

Signed-off-by: Arik Nemtsov <arikx.nemtsov@intel.com>
2015-01-04 20:30:11 +02:00
Jouni Malinen
2961bfa8e1 Remove unused send_eapol() driver op
The send_eapol() callback was used by driver_test.c, but with that
removed, there is no remaining users of the alternative EAPOL frame
transmitting mechanism in wpa_supplicant, i.e., all remaining driver
interfaces use l2_packet instead. Remove the send_eapol() to get rid of
unused code.

Signed-off-by: Jouni Malinen <j@w1.fi>
2014-12-11 15:40:07 +02:00
Jouni Malinen
8105821b39 Replace send_ft_action() driver_op with send_action()
This reduced number of unnecessarily duplicated driver interface
callback functions for sending Action frames by using the more generic
send_action() instead of FT specific send_ft_action().

Signed-off-by: Jouni Malinen <j@w1.fi>
2014-12-06 18:13:29 +02:00
Moshe Benji
471cd6e10c WMM AC: Add add_tx_ts and del_tx_ts driver ops
Add add_tx_ts() and del_tx_ts() ops to notify the driver about
TSPEC add / delete.

Additionally, add wmm_ac_supported flag to indicate
whether the driver supports WMM AC.

Signed-off-by: Moshe Benji <moshe.benji@intel.com>
Signed-off-by: Eliad Peller <eliad@wizery.com>
2014-11-16 20:47:36 +02:00
Bob Copeland
6c1664f605 nl80211: Add new commands to support mesh interfaces
Create init_mesh, mesh_join, and mesh_leave actions to kernel.

Signed-off-by: Javier Lopez <jlopex@gmail.com>
Signed-off-by: Javier Cardona <javier@cozybit.com>
Signed-off-by: Jason Mobarak <x@jason.mobarak.name>
Signed-off-by: Bob Copeland <me@bobcopeland.com>
2014-10-19 12:58:13 +03:00
Arik Nemtsov
984dadc23a TDLS: Set the initiator during tdls_mgmt operations
Some drivers need to know the initiator of a TDLS connection in order
to generate a correct TDLS mgmt packet. It is used to determine
the link identifier IE. Pass this information to the driver.

Signed-off-by: Arik Nemtsov <arikx.nemtsov@intel.com>
2014-10-03 11:52:21 +03:00
Jouni Malinen
fee354c74d nl80211: Add command for changing local MAC address
This can be used to allow wpa_supplicant to control local MAC address
for connections.

Signed-off-by: Jouni Malinen <j@w1.fi>
2014-09-27 19:11:24 +03:00
Jouni Malinen
0ef023e478 Add support for driver command to update roaming policy
The network block bssid parameter can be used to force a specific BSS to
be used for a connection. It is also possible to modify this parameter
during an association. Previously, that did not result in any
notification to the driver which was somewhat problematic with drivers
that take care of BSS selection. Add a new mechanism to allow
wpa_supplicant to provide a driver update if the bssid parameter change
for the current connection modifies roaming policy (roaming
allowed/disallowed within ESS).

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2014-09-11 15:59:42 +03:00
Hu Wang
7baec808ef MACsec: Add driver_ops
This defines new driver_ops to be used with MACsec.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2014-05-09 20:05:28 +03:00
Eliad Peller
e4fa8b120b wpa_supplicant: Add Wake-on-WLAN configuration support
Add a new wowlan_triggers option to wpa_supplicant.conf. The triggers in
this key will be used to configure the kernel wowlan configuration.

For now, support only simple flags. More complex triggers can be added
later on.

Signed-off-by: Eliad Peller <eliadx.peller@intel.com>
2014-04-29 18:59:12 +03:00
Sunil Dutt
96ecea5eb1 Pass TDLS peer capability information in tdls_mgmt
While framing the TDLS Setup Confirmation frame, the driver needs to
know if the TDLS peer is VHT/HT/WMM capable and thus shall construct the
VHT/HT operation / WMM parameter elements accordingly. Supplicant
determines if the TDLS peer is VHT/HT/WMM capable based on the presence
of the respective IEs in the received TDLS Setup Response frame.

The host driver should not need to parse the received TDLS Response
frame and thus, should be able to rely on the supplicant to indicate
the capability of the peer through additional flags while transmitting
the TDLS Setup Confirmation frame through tdls_mgmt operations.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2014-03-27 15:18:48 +02:00
Prameela Rani Garnepudi
95bf699f76 Add get_radio_name() driver wrapper for wpa_supplicant
Signed-off-by: Prameela Rani Garnepudi <prameela.g@samsung.com>
2014-03-21 22:20:38 +02:00
Beni Lev
adef89480d nl80211: Add vendor command support
Add a callback to the driver interface that allows vendor specific
commands to be sent. In addition, a control interface command is added
to expose this new interface outside wpa_supplicant:

Vendor command's format:
VENDOR <vendor id> <sub command id> [<hex formatted data>]

The 3rd argument will be converted to binary data and then passed as
argument to the sub command.

This interface is driver independent, but for now, this is only
implemented for the nl80211 driver interface using the cfg80211 vendor
commands.

Signed-off-by: Beni Lev <beni.lev@intel.com>
2014-03-04 22:24:20 +02:00
Jouni Malinen
2f30cac36f Avoid unnecessary key clearing operations
Track set_key operations per-key index and clear keys on disconnection
only if the key was set (or may have been set which is the case for the
first operation after wpa_supplicant start).

Signed-hostap: Jouni Malinen <j@w1.fi>
2014-01-02 23:49:38 +02:00
Jouni Malinen
152cff6ba6 P2P: Remove WPA_DRIVER_FLAGS_P2P_MGMT option
The option of handling upper layer P2P management operations within the
driver/firmware was originally planned to be used with wpa_supplicant,
but this has not really happened and there is no clear sign of this
being needed in the near term either. This functionality has not been
completed and it is certainly not being kept up-to-date or tested. As
such, it is best to remove it for now and if this or something similar
is needed in the future, it can be brought back once a clear need for it
has been demonstrated first.

Signed-hostap: Jouni Malinen <j@w1.fi>
2013-12-29 18:20:47 +02:00
Jouni Malinen
5e2c3490d5 Android: Add driver_cmd for arbitrary driver commands
This is a mechanism used in Android to extend driver interface in vendor
specific ways. This is included only for the purpose of Android
compatibility. Proper interface commands should be used for any new
functionality.

Signed-hostap: Jouni Malinen <j@w1.fi>
2013-11-22 20:23:08 +02:00
Andrei Otcheretianski
dcca2219ae wpa_supplicant: Update channel switch driver interface
Add csa_settings struct which holds parameters for CSA. Change driver
interface for switch_channel(), so that it will receive this struct and
not only the new frequency as it was before. This allows wpa_supplicant
to provide all the required parameters (beacons, proberesp, assocresp,
CSA IE) which are required by cfg80211 implementation.

Signed-hostap: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
2013-11-17 16:48:33 +02:00
Jouni Malinen
2aec4f3c0c Allow add-BSS operation to re-use existing netdev
When removing and re-adding the first wlan# netdev to hostapd
dynamically, the netdev is already present and should not be removed and
re-added to maintain its state as not-added-by-hostapd so that it does
not get removed automatically.

Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
2013-10-31 22:34:25 +02:00
Jouni Malinen
56f5af489c Interworking: Add support for QoS Mapping functionality for the STA
Indicate support for QoS Mapping and configure driver to update the QoS
Map if QoS Map Set elements is received from the AP either in
(Re)Association Response or QoS Map Configure frame.

This commit adds support for receiving the frames with nl80211 drivers,
but the actual QoS Map configuration command is still missing.

Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
2013-10-18 14:13:45 +03:00
Jouni Malinen
a771c07dfc Add driver status information to control interface
STATUS-DRIVER command can now be used to fetch driver interface status
information. This is mainly for exporting low-level driver interface
information for debug purposes.

Signed-hostap: Jouni Malinen <j@w1.fi>
2013-09-28 17:19:30 +03:00
Jouni Malinen
ec384c566a IBSS RSN: Fix disconnect() with internal SME
Commit 1aef400bf0 implemented IBSS RSN
disconnect() call using sta_deauth() in a way that resulted in NULL
pointer dereference in driver_nl80211.c if SME was in user space. Fix
this by passing the own MAC address in the sta_deauth call.

Signed-hostap: Jouni Malinen <j@w1.fi>
2013-07-21 15:21:38 +03:00