The new broadcast_deauth parameter can be used to disable sending of the
Deauthentication frame whenever AP is started or stopped. The default
behavior remains identical to the past behavior (broadcast_deauth=1).
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
IEEE 802.11ax HE changes to include HE IEs in Beacon and Probe Response
frames. These elements are using vendor specific forms for now since the
IEEE 802.11ax draft is not yet finalized and the element contents is
subject to change.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Add IEEE 802.11ax definitions for config, IEEE structures, and
constants. These are still subject to change in the IEEE process.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This is a copy of the internal HMAC-SHA256 implementation with the hash
block size and output length updated to match SHA384 parameters.
Signed-off-by: Jouni Malinen <j@w1.fi>
The published P802.11ai version does not use CRC32 anymore, so remove
inclusion of crc32.o into wpa_supplicant and hostapd builds based on
CONFIG_FILS=y.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
It can happen if the station is unreachable or sleeping longer than
the actual total GTK rekey timeout. To fix the latter case
wpa_group_update_count may be increased.
Signed-off-by: Günther Kelleter <guenther.kelleter@devolo.de>
wpa_group_update_count and wpa_pairwise_update_count can now be used to
set the GTK and PTK rekey retry limits (dot11RSNAConfigGroupUpdateCount
and dot11RSNAConfigPairwiseUpdateCount). Defaults set to current
hardcoded value (4).
Some stations may suffer from frequent deauthentications due to GTK
rekey failures: EAPOL 1/2 frame is not answered during the total timeout
period of currently ~3.5 seconds. For example, a Galaxy S6 with Android
6.0.1 appears to go into power save mode for up to 5 seconds. Increasing
wpa_group_update_count to 6 fixed this issue.
Signed-off-by: Günther Kelleter <guenther.kelleter@devolo.de>
The new dhcp_server configuration parameter can now be used to configure
hostapd to act as a DHCP relay for DHCPDISCOVER messages received as
FILS HLP requests. The dhcp_rapid_commit_proxy=1 parameter can be used
to configure hostapd to convert 4 message DHCP exchange into a 2 message
exchange in case the DHCP server does not support DHCP rapid commit
option.
The fils_hlp_wait_time parameter can be used to set the time hostapd
waits for an HLP response. This matches the dot11HLPWaitTime in IEEE Std
802.11ai-2016.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This is independent functionality from the core IEEE 802.11 management
handling and will increase significantly in size, so it is cleaner to
maintain this in a separate source code file.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
We can only send module specific messages to syslog and not debug
messages printed with wpa_printf. Add an extra command line parameter
'-s' to allow it. The feature is enabled with compile flag
CONFIG_DEBUG_SYSLOG as for wpa_supplicant and behaves in the same manner
as the wpa_supplicant -s command line argument.
Signed-off-by: Wojciech Dubowik <Wojciech.Dubowik@neratec.com>
The new control interface command "REQ_BEACON <STA addr>
[req_mode=<mode>] <beacon request>" can now be used to request hostapd
to transmit a measurement request to request a beacon report from an
associated STA. This command returns the assigned dialog token (1-255)
or FAIL on failure.
Signed-off-by: Jouni Malinen <j@w1.fi>
rrm_beacon_report=1 can now be used to make hostapd advertise capability
for beacon reports (passive, active, table). Actual mechanism for
sending out beacon requests will be added in separate commits.
Signed-off-by: Jouni Malinen <j@w1.fi>
The actual BSS configuration parameter can be updated with the SET
control interface command, so there is no need to maintain a separate
per-BSS parameter and a separate control interface handling for this.
Signed-off-by: Jouni Malinen <j@w1.fi>
The after_beacon and beacon TX queue parameters has not been
configurable through this mechanism for years, so do not list them in
hostapd.conf notes.
Signed-off-by: Jouni Malinen <j@w1.fi>
The optional url=<URL> parameter was stored in allocated memory and that
memory was leaked if some following parameter parsing attempts failed.
Signed-off-by: Jouni Malinen <j@w1.fi>
Previously, update command with invalid value got rejected, but the
actual configuration data was updated anyway.
Signed-off-by: Jouni Malinen <j@w1.fi>
Previously, an invalid eapol_version update command was rejected, but
the actual configuration value was updated.
Signed-off-by: Jouni Malinen <j@w1.fi>
Previously, this was noted in error log, but the invalid value was
stored in the configuration without rejecting it.
Signed-off-by: Jouni Malinen <j@w1.fi>
Yet some more commands take STA address as the only parameter. Add
command completion support for the following commands:
signature, sa_query, send_qos_map_conf and req_lci
Signed-off-by: Mikael Kanstrup <mikael.kanstrup@sonymobile.com>
More than one command takes STA address as the only parameter. Make use
of a common completion routine.
Signed-off-by: Mikael Kanstrup <mikael.kanstrup@sonymobile.com>
Some commands are missing help description making them not show up in
the list of supported commands. Add command help description for all
missing commands.
Signed-off-by: Mikael Kanstrup <mikael.kanstrup@sonymobile.com>
The new hostapd configuration parameter fils_realm=<realm> can now be
used to configure one or more FILS realms to advertise for ERP domains
when using FILS. This replaces the use of erp_domain=<domain> parameter
for the FILS use case.
Signed-off-by: Jouni Malinen <j@w1.fi>
Setting wep_key# to an empty string will now clear a previously
configured key. This is needed to be able to change WEP configured AP to
using WPA/WPA2 through the hostapd control interface SET commands.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This adds support for nl80211 NL80211_CMD_SET_MULTICAST_TO_UNICAST
command.
By setting the new hostapd configuration option multicast_to_unicast=1,
hostapd configures this AP to perform multicast to unicast conversion.
When enabled, all multicast packets with ethertype ARP, IPv4, or IPv6
(possibly within an 802.1Q header) will be sent out to each station once
with the destination (multicast) MAC address replaced by the station's
MAC address. Note that this may break certain expectations of the
receiver, e.g., the ability to drop unicast IP packets encapsulated in
multicast L2 frames, or the ability to not send destination unreachable
messages in such cases.
This also does not implement Directed Multicast Service (DMS).
Signed-off-by: Michael Braun <michael-dev@fami-braun.de>
This makes it easier to write hwsim test cases to verify management
frame processing sequences with dropped or modified frames. When
ext_mgmt_frame_handling is used, this new command can be used to request
hostapd to process a received a management frame, e.g., based on
information reported in the MGMT-RX events.
This is more or less identical to the earlier wpa_supplicant commit
4de70e2330 ('Add MGMT_RX_PROCESS test
command for wpa_supplicant'), but for hostapd.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Allow configuration of Beacon frame TX rate from hostapd.conf with
"beacon_rate=xx" option. The following format is used to set
legacy/HT/VHT beacon rates:
Legacy (CCK/OFDM rates):
beacon_rate=<legacy rate in 100 kbps>
HT:
beacon_rate=ht:<HT MCS>
VHT:
beacon_rate=vht:<VHT MCS>
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Commit 4ec1fd8e42 ('FT: Differentiate
between FT for station and for AP in build') renamed all
CONFIG_IEEE80211R instances within src/ap/* to CONFIG_IEEE80211R_AP, but
it did not change hostapd/* files to match. While this does not cause
much harm for normal use cases, this broke some test builds where
wpa_supplicant build is used to build in hostapd/*.c files for analysis.
Fix this by completing CONFIG_IEEE80211R_AP renaming.
Signed-off-by: Jouni Malinen <j@w1.fi>
Remove the extra equals sign from the line since hostapd usage text does
not have it for other entries either (while wpa_supplicant does and this
was likely copy-pasted from there).
Signed-off-by: Jouni Malinen <j@w1.fi>
Previously, CONFIG_IEEE80211R enabled build that supports FT for both
station mode and AP mode. However, in most wpa_supplicant cases only
station mode FT is required and there is no need for AP mode FT.
Add support to differentiate between station mode FT and AP mode FT in
wpa_supplicant builds by adding CONFIG_IEEE80211R_AP that should be used
when AP mode FT support is required in addition to station mode FT. This
allows binary size to be reduced for builds that require only the
station side FT functionality.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Add a configuration option in hostapd.conf and in neighbor report that
sets an AP as stationary. To enable this option on the current AP set
the config option stationary_ap to 1. To set a neighbor entry to be
marked as stationary add the word stat to the SET_NEIGHBOR command. This
option tells hostapd to send LCI data even if it is older than requested
by max age subelement in RRM request.
Signed-off-by: David Spinadel <david.spinadel@intel.com>
In case that LCI or location civic configuration is cleared,
free the buffer holding the corresponding information to avoid
cases that the information is considered as valid/useful.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Add signal level information to the station tracking information. Also
make it available via the "TRACK_STA_LIST" control command.
Signed-off-by: Kevin Mahoney <k.mahoney@cablelabs.com>
Commit 56885eecf4 ('hostapd: Add UDP
support for ctrl_iface') added dl_list_init() for global_ctrl_dst to
hostapd_global_ctrl_iface_init().
Though, hostapd_global_ctrl_iface_init() is only called from
main.c:main(), which already initializes global_ctrl_dst unconditionally
before. Same with global_ctrl_sock.
Remove this duplicate initialization.
Signed-off-by: Michael Braun <michael-dev@fami-braun.de>
Add list_sta command to print addresses of all stations. Command
added to both wpa_cli and hostapd_cli.
Signed-off-by: Mikael Kanstrup <mikael.kanstrup@sonymobile.com>
Events received as an immediate result of control interface commands
end up on the control request message callback function instead of
the registered read socket. This makes for example the station list
used for complete functions for disassociate and deauthenticate out
of sync. Process events in the message callback function too to ensure
no events are missed.
Signed-off-by: Mikael Kanstrup <mikael.kanstrup@sonymobile.com>
Code for connecting/reconnecting to the hostapd control interface
is found duplicated a number of times. Create a common reconnect
helper function to avoid code duplication.
Signed-off-by: Mikael Kanstrup <mikael.kanstrup@sonymobile.com>
Whenever reconnecting the control interface the hostapd station list
is unknown as stations might have dropped or connected. Refresh the
list of stations used for command completion on cli connect, reconnect
and interface change.
Signed-off-by: Mikael Kanstrup <mikael.kanstrup@sonymobile.com>
