Commit graph

219 commits

Author SHA1 Message Date
Jouni Malinen
961750c1e8 WPS: Share a common function for error strings
This makes it easier to maintain the list of WPS_EI_* error values and
matching strings.

Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
2013-08-23 16:32:34 +03:00
Junli Zhao
c7a67a7719 WPS: Disconnect when removing existing WPS network block
wpas_clear_wps() was just clearing the current wpa_s->current_ssid
pointer when removing a WPS network block which with the device was
associated. This could leave the association up even though the network
block had already been removed. Prevent this by explicitly disconnecting
from the network instead of such clearing current_ssid.

Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
2013-07-08 12:09:18 +03:00
Jouni Malinen
f3e907a745 WPS: Clear connection failure counts on WPS success
The WPS provisioning case does not result in successful connection by
design and as such, this can result in networks getting temporarily
disabled. Avoid this by clearing the failure counts on WPS success.

Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
2013-05-15 17:33:50 +03:00
Jouni Malinen
170f5663dc WPS NFC: Connect using learnt credential after NFC Tag read
Instead of just adding the new network, prefer the network learnt from a
configuration token during the first connection attempt. This makes the
WPS NFC case behave similarly to the in-band provisioning cases if there
are more preferred networks in the scan results.

Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
2013-05-15 16:46:45 +03:00
Vinayak Kamath
741ed9fc25 WPS: Remove duplicate networks after WPS
Each attempt to connect to the same network using WPS would result
in the duplicate configuration getting added. Avoid such redundant
additions by comparing the network configuration with an already
existing one and remove the older network if the new credential
provisioned through WPS is identical.

Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
2013-04-30 13:35:50 +03:00
Jouni Malinen
88c8bf311e WPS NFC: Allow configuration token to be built from network block
"WPS_NFC_CONFIG_TOKEN <WPS/NDEF> <network id>" can now be used to build
an NFC configuration token from a locally configured network.

Signed-hostap: Jouni Malinen <j@w1.fi>
2013-04-01 21:28:57 +03:00
Jouni Malinen
e205401c72 WPS ER: Allow Enrollee to be specified with MAC address
wps_er_pbc and wps_er_pin can now be used with both the UUID and MAC
Address of the Enrollee.

Signed-hostap: Jouni Malinen <j@w1.fi>
2013-04-01 20:52:44 +03:00
Jouni Malinen
59307b3007 WPS ER: Allow AP to be specified with BSSID
This extends the WPS ER commands that previously accepted only UUID as
an identifier for an AP to use either UUID or BSSID for this.

Signed-hostap: Jouni Malinen <j@w1.fi>
2013-04-01 20:32:09 +03:00
Jouni Malinen
5c9d63d46f WPS: Be more careful with pre-configured DH parameters
Make the implementation more robust against error cases with
pre-configured DH parameters.

Signed-hostap: Jouni Malinen <j@w1.fi>
2013-04-01 19:27:32 +03:00
Masashi Honma
97236cee6a WPS: Skip rescanning after provisioning if AP was configured
If WPS provisioning step is completed with an AP that is in WPS
configured state, we can skip a second scan after the provisioning step
since the AP is unlikely to change its configuration in such a case.
This can speed up WPS connection a bit by removing an unneeded scan.

Signed-hostap: Masashi Honma <masashi.honma@gmail.com>
2013-03-31 20:06:42 +03:00
Jouni Malinen
9599ccc2dd WPS: Clear after_wps on new WPS connection
The after_wps counter could have potentially be left in its old non-zero
value in some WPS sequences which could result in a single-channel scan
being used based on obsolete information. Clear after_wps in
wpas_wps_reassoc() to make sure this does not happen.

Signed-hostap: Jouni Malinen <j@w1.fi>
2013-03-31 18:05:42 +03:00
Jouni Malinen
702621e6dd WPS: Use latest updated BSS entry if multiple BSSID matches found
If the AP (P2P GO) has changes its channel of SSID recently, the BSS
table may have multiple entries for a BSSID. Select the one which was
most recently updated for WPS/P2P operations in such case to increase
the likelihood of using current information.

Signed-hostap: Jouni Malinen <j@w1.fi>
2013-03-31 18:05:42 +03:00
Jouni Malinen
94d7acf3df WPS NFC: Fix build without CONFIG_WPS_ER
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
2013-03-13 00:02:52 +02:00
Jouni Malinen
f3f2ba2e6e WPS NFC: Add connection handover support for ER
wpa_supplicant can now generate the WPS carrier record for connection
handover response when acting as an ER. The AP whose configuration is
provided in this way is identified with an UUID as an argument to
wps-nfc.py.

Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
2013-02-24 10:56:29 +02:00
Jouni Malinen
5ab9a6a53e WPS: Add support for NFC handover select generation with wpa_supplicant
When wpa_supplicant is controlling an AP mode interface, it can generate
the alternative carrier record for NFC connection handover select
message similarly to the way this is done in hostapd.

Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
2013-02-15 12:34:55 +02:00
Jouni Malinen
bbf41865c9 WPS: Add support for config token generation with wpa_supplicant
When wpa_supplicant is controlling an AP mode interface, it can generate
the NFC configuration token similarly to the way this is done in
hostapd.

Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
2013-02-15 11:47:52 +02:00
Jouni Malinen
042ec551d4 WPS: Use pre-configured NFC password token instead of overriding it
"WPS_NFC_TOKEN <WPS/NDEF>" used to generate a new NFC password token
regardless of whether there was a pre-configured token in the
configuration. Change this to use the pre-configured value, if
available, instead. This allows the same command to be used to write the
password token to an NFC tag more conveniently.

Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
2013-02-15 11:24:29 +02:00
Jouni Malinen
e47588279a WPS: Report NFC connection handover completion differently
Instead of reporting only one connection handover message, report
completion of NFC connection handover with carrier record from both the
request and select messages.

Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
2013-02-11 18:43:46 +02:00
Jouni Malinen
bbaaaee171 WPS: Fetch only the carrier record from wpa_supplicant for NFC
Since there could be multiple carrier records, it is cleaner to build
only the WPS carrier record instead of full NFC connection handover
request within wpa_supplicant.

Signed-hostap: Jouni Malinen <j@w1.fi>
2013-02-10 18:19:59 +02:00
Jouni Malinen
9c75e9fb81 WPS: Verify wpa_config_set() return value more consistently
Even though this command is very unlikely to fail, in theory, it could
and the WPS connection would fail in such a case. Return more clearer
failure indication in such a case without even trying to start
reassociation.

Signed-hostap: Jouni Malinen <j@w1.fi>
2013-01-12 17:51:53 +02:00
Jouni Malinen
318e772ad1 WPS: Update configuration file after re-enabling networks
Network blocks are disabled during a WPS provisioning step and 10
seconds after this to allow the newly provisioned network to be
selected. The disabled=1 flag gets written to the configuration file
when the credential is added since it happens during this process.
Update the file again after the networks have been re-enabled to avoid
leaving the configuration file into state that is not consistent with
the running configuration.

Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
2012-12-21 20:11:26 +02:00
Sunil Dutt
6fbcbc07e4 WPS: Optimize post-WPS scan even if EAP-Failure is not received
Commit 17a4734dc4 shall optimize the
post-WPS scan based on the channel used during the provisioning only
when the EAP-Failure frame is received. In cases where the EAP-Failure
frame is missed, this optimization shall not happen resulting in the
scan in all the channels thus consuming more time for the connection.
This commit enhances this by storing the requisite information after
the M8 frame is received.

Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
2012-12-21 15:30:39 +02:00
Jouni Malinen
207fb86411 WPS: Remove deprecated UFD config method and OOB ctrl_iface
The UFD (USB flash drive) configuration method was deprecated in WSC
2.0. Since this is not known to be used, remove the UFD implementation
from hostapd and wpa_supplicant to allow the WPS implementation to be
cleaned up. This removes the now unused OOB operations and ctrl_iface
commands that had already been deprecated by the new NFC operations.

Signed-hostap: Jouni Malinen <j@w1.fi>
2012-11-11 13:01:06 +02:00
Jouni Malinen
b363121a20 WPS: Reject invalid credential more cleanly
If WPS Registrar tries to provision a WPA/WPA2-Personal network without
including a valid Network Key, the network block cannot be used to
connect to the network. Reject such credential without adding the
network block. This makes wpa_supplicant send WSC_NACK as a response to
the invalid Credential and stop the provisioning process immediately
rather than only after trying unsuccessfully to connect to the network.

Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
2012-11-01 16:30:35 +02:00
Jouni Malinen
9f36eac6e5 WPS: Remove old OOB NFC interface
The old WPS interface for using NFC has no known deployments and even
the binary libraries referenced here are not easily available anymore.
Since the new interface for using NFC with WPS covers the same
functionality, remove the old implementation to clean up WPS
implementation.

Signed-hostap: Jouni Malinen <j@w1.fi>
2012-10-28 18:20:03 +02:00
Jouni Malinen
bd3a373767 WPS: Use AP Channel attribute in credential to speed up scan
When WPS is used with NFC connection handover, the AP may indicate its
operating channel within the credential information. Use this
informatiom, if present, to speed up the scan process.

Signed-hostap: Jouni Malinen <j@w1.fi>
2012-10-28 18:02:04 +02:00
Jouni Malinen
e65552ddf2 WPS: Add preliminary NFC connection handover support for Enrollee
This commit adds new wpa_supplicant ctrl_iface commands to allow
external programs to go through NFC connection handover mechanism
with wpa_supplicant taking care of the WPS processing. This version
includes only the case where wpa_supplicant is operating as a
station/Enrollee.

Signed-hostap: Jouni Malinen <j@w1.fi>
2012-10-28 17:39:46 +02:00
Sunil Dutt
ec947ffcd8 WPS: Reenable the networks disabled during wpa_wpas_reassoc
During the association for the WPS handshake all the other configured
networks are disabled. This patch makes wpa_supplicant reenable the
disabled networks after the success/failure of the WPS handshake.

Signed-hostap: Sunil Dutt Undekari <duttus@codeaurora.org>
2012-10-04 21:11:04 +03:00
Masashi Honma
6df865face Remove unused function warning in WPS NFC case
When I use CONFIG_WPS_NFC=y a warning appears.

wps_supplicant.c:1872:12: warning: 'wpas_wps_add_nfc_password_token'
defined but not used [-Wunused-function]

This patch removes this warning.

Signed-hostap: Masashi Honma <masashi.honma at gmail.com>
2012-09-15 22:02:09 -07:00
Jouni Malinen
620c783753 Use BSS entries instead of scan results for BSS selection
This allows the BSS selection functions to be called without having the
scan result data structure. This can be used to skip extra scans in
cases where previous results can be considered fresh.

Signed-hostap: Jouni Malinen <j@w1.fi>
2012-09-02 19:56:57 +03:00
Jouni Malinen
a462036a47 WPS: Allow AP that becomes active be tried immediately
Clear the possible blacklisting of a WPS AP during WPS PIN iteration if
the AP moves to selected registrar TRUE state or if it adds our MAC
address to the list of authorized MACs.

Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
2012-08-27 13:51:35 +03:00
Jouni Malinen
f9f0526bcd WPS: Maintain more AP state during WPS PIN iteration
Maintain state of WPS APs during iteration to find the correct AP for
WPS PIN operation when no specific BSSID is specified. This information
can be used for optimizing the order in which the APs are tried. This
commit is only adding the collection of the information and more
detailed debug information to make debug logs more helpful in figuring
out how the AP selection order could be improved.

Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
2012-08-27 13:48:11 +03:00
Jouni Malinen
00e5e3d509 Disable network block temporarily on authentication failures
If 4-way handshake fails due to likely PSK failure or if EAP
authentication fails, disable the network block temporarily. Use longer
duration if multiple consecutive failures are seen.

Signed-hostap: Jouni Malinen <j@w1.fi>
2012-08-26 23:35:07 +03:00
Jouni Malinen
a120c3fad6 WPS: Remove unused credential handlers for 802.1X
The WPA_AUTH_WPA and WPA_AUTH_WPA2 cases have already been rejected in
this function when execution comes here. In theory, support for
WPA-Enterprise could be added, but since that has not happened over the
years, there is no good reason to keep this dead code here.

Signed-hostap: Jouni Malinen <j@w1.fi>
2012-08-19 19:10:40 +03:00
jim1_lin
c8b245b6a4 WPS: Update dev.config_methods in wps_update_config
dev.config_methods was not updated when wps_update_config was called.
This could lead to mismatching config methods between Probe Request and
M1 packets. Add missing part for it.
2012-08-04 20:14:59 +03:00
Jouni Malinen
cae2119c86 P2P: Leave forced BSSID parameter for P2P group
P2P group is only going to use a single GO, so we can leave the fixed
BSSID parameter set for the actual data connection in addition to the
initial WPS provisionign step. This can speed up operations with drivers
that select BSS internally by allowing them to skip an extra scan when
the BSSID and frequency of the GO is already known.

Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
2012-07-25 16:18:12 +03:00
Jouni Malinen
bfc62fe133 WPS: Share a single function for generating NFS password tokens
There is no need for both hostapd and wpa_supplicant to have their
own functions for this.

Signed-hostap: Jouni Malinen <j@w1.fi>
2012-06-28 21:01:37 +03:00
Jouni Malinen
72df0cd28c WPS: Use random_get_bytes() for NFC password id
os_random() may not be seeded properly, so use stronger mechanism for
generating the password id for NFC password tokens.

Signed-hostap: Jouni Malinen <j@w1.fi>
2012-06-28 20:40:16 +03:00
Jouni Malinen
e484e927a6 WPS: Allow NFC password token from AP to be used with wps_reg
The AP PIN on wps_reg command can now be replaced with special value
"nfc-pw" to use device password from a NFC password token from the AP.

Signed-hostap: Jouni Malinen <j@w1.fi>
2012-06-28 19:41:26 +03:00
Jouni Malinen
e6ea2a451c WPS ER: Add support for using NFC password token from an Enrollee
WPS_NFC_TAG_READ ctrl_iface command can now be used to add NFC password
tokens to ER.

Signed-hostap: Jouni Malinen <j@w1.fi>
2012-06-28 17:34:46 +03:00
Jouni Malinen
1cea09a9e2 WPS ER: Add support for building NFC configuration token
WPS_ER_NFC_CONFIG_TOKEN command can now be used to build a NFC
configuration token based on AP Settings learnt with WPS_ER_LEARN
or set with WPS_ER_CONFIG.

Signed-hostap: Jouni Malinen <j@w1.fi>
2012-06-28 16:35:51 +03:00
Jouni Malinen
d7645d239d WPS: Add support for NFC configuration token from external program
The new wpa_supplicant ctrl_iface command WPS_NFC_TAG_READ can now be
used to process NFC tags read by external programs to initiate
wpa_supplicant to use NFC Configuration Token to create a new network.

Signed-hostap: Jouni Malinen <j@w1.fi>
2012-06-28 13:59:29 +03:00
Jouni Malinen
5bb7ae1f0c WPS: Fix error case in NFC password token generation
Need to verify that wps_build_nfc_pw_token() returned a valid buffer
before trying to encapsulate it for NDEF.

Signed-hostap: Jouni Malinen <j@w1.fi>
2012-06-28 13:23:58 +03:00
Jouni Malinen
3f2c8ba6d3 WPS: Add new mechanism for NFC config method using password token
Instead of requiring low-level access to an NFC device and synchronous
operations, the new WPS_NFC_TOKEN and WPS_NFC ctrl_iface commands can be
used to build a NFC password token and initiate WPS protocol run using
that token (or pre-configured values) as separate commands. The
WPS_NFC_TOKEN output can be written to a NFC tag using an external
program, i.e., wpa_supplicant does not need to have low-level code for
NFC operations for this.

Signed-hostap: Jouni Malinen <j@w1.fi>
2012-06-27 21:22:12 +03:00
Jouni Malinen
476dea24ff WPS: Cancel WPS operation also in DISCONNECTED state
It is possible for wpa_state to be WPA_DISCONNECTED when a new scan is
scheduled to be started in the future. If wpas_wps_cancel() gets called
(e.g., through control interface wps_cancel or a P2P group removal)
while in that state, the WPS operation (scan request and special network
block) were not removed. Fix this by clearing the WPS operations both in
WPA_SCANNING and WPA_DISCONNECTED states.

Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
intended-for: hostap-1
2012-06-06 22:07:11 +03:00
Jouni Malinen
2c1e557507 WPS: Fix BSSID filter handling
If WPS commands are used with a specific BSSID instead of wildcard,
the BSSID that was supposed to be used only for the provisioning step
may end up getting copied to the network block that gets provisioned
based on the WPS credentials. Fix this by clearing ssid->bssid_set
when creating the network block by replacing the block used for WPS
provisioning.

This issue could show up with the provisioned network not getting
selected properly with APs that have multiple radios. Depending on
the driver, this could result in only a single one of the available
BSSes being available or the connection failing completely.

Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
intended-for: hostap-1
2012-05-11 13:29:43 +03:00
Ben Greear
157cdad59f wpa_supplicant: Fix overlapping memcpy on WPS interface addition
I think this should fix the following valgrind complaint:

==1972== Source and destination overlap in memcpy(0x5181708, 0x5181708, 16)
==1972==    at 0x4A073BA: memcpy (mc_replace_strmem.c:602)
==1972==    by 0x45872B: wpas_wps_set_uuid (wps_supplicant.c:1116)
==1972==    by 0x4599EC: wpas_wps_update_config (wps_supplicant.c:1747)
==1972==    by 0x4C8DB0: wpa_supplicant_update_config (wpa_supplicant.c:3090)
==1972==    by 0x4C3E5E: wpa_supplicant_reload_configuration (wpa_supplicant.c:746)
==1972==    by 0x4B8B37: wpa_supplicant_ctrl_iface_process (ctrl_iface.c:4082)
==1972==    by 0x4BA39C: wpa_supplicant_ctrl_iface_receive (ctrl_iface_unix.c:168)
==1972==    by 0x4114D4: eloop_sock_table_dispatch_table (eloop.c:335)
==1972==    by 0x411541: eloop_sock_table_dispatch (eloop.c:352)
==1972==    by 0x41200D: eloop_run (eloop.c:766)
==1972==    by 0x4C8B43: wpa_supplicant_run (wpa_supplicant.c:3010)
==1972==    by 0x4D44AD: main (main.c:286)

Signed-hostap: Ben Greear <greearb@candelatech.com>
intended-for: hostap-1
2012-05-10 10:57:59 +03:00
Anirban Sirkhell
71dd3b78f9 WPS: Allow vendor specific attribute to be added into M1
wps_vendor_ext_m1 configuration parameter can now be used to add a
vendor specific attribute into the WPS M1 message, e.g., for
Windows Vertical Pairing.

Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
2012-04-04 00:08:57 +03:00
Jouni Malinen
a565c23bf3 WPS: Fix regression in post-WPS scan optimization
Commit 3c85f144ce fixed issues with P2P
Action frame TX after disconnection by clearing wpa_s->assoc_freq.
This resulted in a regression to the post-WPS scan optimization that
used wpa_s->assoc_freq to enable fast single-channel scan. Fix this by
copying wpa_s->assoc_freq to a local variable before calling
wpa_supplicant_deauthenticate() that ends up calling
wpa_supplicant_mark_disassoc() which will clear assoc_freq.

Reported-by: Angie Chinchilla <angie.v.chinchilla@intel.com>
intended-for: hostap-1
Signed-hostap: Jouni Malinen <j@w1.fi>
2012-02-12 13:54:15 +02:00
Jouni Malinen
0f3d578efc Remove the GPL notification from files contributed by Jouni Malinen
Remove the GPL notification text from the files that were
initially contributed by myself.

Signed-hostap: Jouni Malinen <j@w1.fi>
2012-02-11 19:39:36 +02:00
Jouni Malinen
32cdcf15b2 WPS: Disable AP PIN after 10 consecutive failures
While the exponential increase in the lockout period provides an
efficient mitigation mechanism against brute force attacks, this
additional trigger to enter indefinite lockout period (cleared by
restarting hostapd) will limit attacks even further by giving maximum of
10 attempts (without authorized user action) even in a very long term
attack.

Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
2012-01-30 17:36:14 +02:00
Jouni Malinen
1e7fb4f1b7 WPS: Use single channel scan if AP channel already known
If the BSSID of the AP is specified in the WPS command, the target
AP is likely already in the BSS table and its operating channel is
known. Use this information to speed up connection by only scanning
the known channel.

Signed-hostap: Jouni Malinen <j@w1.fi>
2011-12-31 13:17:20 +02:00
Jouni Malinen
d9d87c3357 Disassociate when starting WPS search
Previously, the WPS scans could have been done in associated state if we
happened to be associated when the request to use WPS was received. This
can slow down scanning and end up in unexpected state if no WPS
association is tried. Avoid these issues by disconnecting when WPS
search is started.

Signed-hostap: Jouni Malinen <j@w1.fi>
2011-12-11 18:30:47 +02:00
Jouni Malinen
0b7a25c00f Use normal scan before sched_scan if that can speed up connection
When normal scan can speed up operations, use that for the first three
scan runs before starting the sched_scan to allow user space sleep more.
We do this only if the normal scan has functionality that is suitable
for this or if the sched_scan does not have better support for multiple
SSIDs.

Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
2011-11-28 18:36:36 +02:00
Christian Lamparter
6bf731e8ce wpa_supplicant: Unify hardware feature data
The hardware feature data is required in several different places
throughout the code. Previously, the data was acquired and freed on
demand, but with this patch wpa_supplicant will keep a single copy
around at runtime for everyone to use.

Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
2011-10-23 17:21:50 +03:00
Andrii Bordunov
2c4f80d519 WPS: Use ifdef blocks consistently for CONFIG_WPS_REG_DISABLE_OPEN
The registrar variable is used only if this macro is defined, so no
need to set it otherwise.
2011-10-22 22:21:53 +03:00
Bharat Chakravarty
a9355fac5f WPS: Set Probe Request config methods based on configuration
Instead of hardcoding the Config Methods attribute value in Probe
Request frames, set this based on the configured parameter
config_methods to allow correct set of methods to be advertised.
2011-09-01 15:24:45 +03:00
Bharat Chakravarty
6fb6d842bb WPS: Set RF bands based on driver capabilities
Instead of hardcoding support for both 2.4 GHz and 5 GHz bands,
use driver capabilities to figure out which bands are supported.
2011-08-31 17:53:55 +03:00
Jouni Malinen
d87e90b646 WPS: Check malloc success on workaround path
ssid->ssid could be NULL here if malloc failed, so better check that
consistently.
2011-07-15 14:21:50 +03:00
Jouni Malinen
20a0b03deb Clear WPA and EAPOL state machine config pointer on network removal
Make sure that the WPA and EAPOL state machines do not hold a pointer
to a network configuration that is about to be freed. This can fix
potential issues with references to freed memory.
2011-06-27 19:02:24 +03:00
Jayant Sane
3734552f15 P2P: Add WpsFailed signal in P2P D-Bus
Signal is triggered if an error occurs during WPS provisioning phase.

Signed-off-by: Jean-Michel.Bachot <jean-michelx.bachot@intel.com>
Signed-off-by: Jayant Sane <jayant.sane@intel.com>
2011-06-25 11:47:04 +03:00
Jayant Sane
c2762e410f P2P: Update D-Bus network object semantics during group formation
Do not emit network objects during P2P group formation since such
network objects can confuse certain apps. Instead, a persistent group
object is created to allow apps to keep track of persistent groups.
Persistent group objects only represent the info needed to recreate the
group.

Also fixes a minor bug in the handling of persistent group objects
during WPS operations.

Signed-off-by: Jayant Sane <jayant.sane@intel.com>
2011-06-23 21:25:13 +03:00
Johannes Berg
2f646b6e83 WPS: Store (secondary) device type as binary
Instead of converting back and forth from the string representation,
always use the binary representation internally.

Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2011-03-17 18:50:22 +02:00
Jouni Malinen
85a821d611 WPS: Fix copying of UUID from the first interface
Use the first interface (last in the list), not the last added
interface. In addition, use the same routine to set the UUID
after reconfiguration.
2011-03-17 18:07:00 +02:00
Jean-Michel Bachot
a9e86bfb74 WPS: Add secondary device types into Probe Request frames
The secondary device type list is an optional attribute in the WSC IE.

Signed-off-by: Jean-Michel Bachot <jean-michelx.bachot@linux.intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2011-03-17 11:09:49 +02:00
Jouni Malinen
ca29141c83 WPS: Copy UUID from the first interface
Instead of generating a different UUID for each interface, use the
same UUID that was either configured of generated for the first
interface. This avoids potential issues with PBC session overlap
detection should multiple interfaces end up running a PBC scan
at the same time which may happen at least in some P2P use cases.
2011-03-10 18:36:07 +02:00
Jouni Malinen
b89883a444 P2P: Notify WPS-M2D event on parent interface and handle PBC overlap
GO may use M2D to notify that PBC overlap was detected if the GO was
configured to allow only a specific P2P Device to connect using PBC.
We need to report the M2D message on the parent interface if a
separate group interface is used. In addition, we can stop the P2P
operation if PBC overlap was indicated similarly to what we are
already doing in th case the overlap is detected locally.
2011-02-22 12:20:16 +02:00
Ben Greear
4c9695be8f WPS ER: Stop eloop only on the last terminate_cb
This allows all WPS ER instances to be cleaned up properly if more
than one interface has an active WPS ER when wpa_supplicant is being
killed.
2011-02-21 21:47:46 +02:00
Johannes Berg
d1c8ac88b9 DBus: Publish provisioned keys in network properties
When the network was provisioned, we need to get the keys to be able to
reconnect without new provisioning. To be able to publish those keys but
not normally configured ones, add a new attribute to struct wpa_ssid
indicating whether or not keys may be exported.

Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2011-02-02 17:00:12 +02:00
Chao-Wen Yang
449adbaca9 WPS: Indicate WPS-FAIL event on EAPOL timeout-based failure callback
If the EAPOL processing times out (e.g., if the AP stops replying
to messages for some reason) during WPS negotiation, we need to
indicate WPS-FAIL event from eapol_cb since no other WPS failure is
reported for this particular case.
2011-01-13 18:04:33 +02:00
Chao-Wen Yang
c5cf0a18f1 WPS: Add mechanism for indicating non-standard WPS errors
Previously, only the Configuration Error values were indicated in
WPS-FAIL events. Since those values are defined in the specification
it is not feasible to extend them for indicating other errors. Add
a new error indication value that is internal to wpa_supplicant and
hostapd to allow other errors to be indicated.

Use the new mechanism to indicate if negotiation fails because of
WEP or TKIP-only configurations being disallows by WPS 2.0.
2011-01-13 17:50:59 +02:00
Jouni Malinen
6c6ad81f9c WPS: Make WPS-AP-AVAILABLE* events a bit more consistent
The BSS table entries may be in more or less random order and it is
better to show the most likely WPS configuration method in a way that is
somewhat more consistent instead of just showing the method of the first
BSS entry found in the table.
2011-01-05 11:49:03 +02:00
Jouni Malinen
f981eabcf0 WPS: Add option to disable open networks by default
CONFIG_WPS_REG_DISABLE_OPEN=y can be used to configure wpa_supplicant
to disable open networks by default when wps_reg command is used to
learn the current AP settings. When this is enabled, there will be a
WPS-OPEN-NETWORK ctrl_iface event and the user will need to explicitly
enable the network (e.g., with "select_network <id>") to connect to
the open network.
2010-12-30 12:28:13 +02:00
Jouni Malinen
70d84f11fe WPS: Add wps_ap_pin ctrl_iface command for wpa_supplicant AP mode
This can be used to control the AP PIN in wpa_supplicant AP mode
in the same way as the identical command in hostapd ctrl_iface.
2010-11-17 16:46:55 +02:00
Jouni Malinen
3e7533b399 WPS ER: Show SetSelectedRegistrar events as ctrl_iface events
This makes it easier to figure out if something goes wrong in
preparing the AP for enrolling a station.
2010-10-25 21:29:22 +03:00
Jouni Malinen
ef10f4733f WPS ER: Add wps_er_set_config to use local configuration
This command can be used to enroll a network based on a local
network configuration block instead of having to (re-)learn the
current AP settings with wps_er_learn.
2010-10-20 13:37:01 +03:00
Jouni Malinen
092acb5441 WPS: Add virtual flags in Config Methods for WPS 2.0 if needed
This is a workaround for incorrect configuration (missing
virtual/physical identifier for config methods) for WPS 2.0 to
allow unmodified configuration from WPS 1.0 to be used while
enforcing compliant WPS 2.0 values.
2010-10-16 12:57:47 +03:00
Jouni Malinen
545cc6af25 P2P: Send WPS-FAIL event to parent interface, too
This makes it easier to figure out what went wrong during group
formation when per-group interfaces are used.
2010-10-14 20:52:31 +03:00
Jouni Malinen
81611b95ff WPS: Add Config Error into WPS-FAIL events
This makes it easier to figure out what could have failed in the
WPS protocol and potentially provide more information for the
user on how to resolve the issue.
2010-10-14 20:49:54 +03:00
Jouni Malinen
d9c8a7c44c Fix build with CONFIG_WPS_OOB 2010-10-06 16:40:20 +03:00
Jouni Malinen
9647120b07 WPS: Add more verbose debug info on PBC session overlap detection 2010-09-20 15:08:52 -07:00
Jouni Malinen
ff28ccafd5 WPS: Add BSSID to strict validation error messages
This makes it easier to figure out which AP is sending invalid
Beacon or Probe Response frames.
2010-09-20 14:54:22 -07:00
Ardong Chen
2f9929ffcc WPS: Allow pending WPS operation to be cancelled
A new ctrl_interface command, WPS_CANCEL, can now be used to cancel
a pending or ongoing WPS operation. For now, this is only available
with wpa_supplicant (either in station or AP mode). Similar
functionality should be added for hostapd, too.
2010-09-10 10:30:25 -07:00
Ardong Chen
014732ea81 WPS: Fix timeout event to be sent over ctrl_interface
This was supposed to be sent to external event monitors, i.e., to
use wpa_msg instead of wpa_printf.
2010-09-10 10:30:25 -07:00
Jouni Malinen
812bf56ab1 Fix build without CONFIG_P2P=y 2010-09-09 07:20:28 -07:00
Jouni Malinen
e9a7ae41fa P2P: Use SSID from GO Negotiation to limit WPS provisioning step
In order to avoid picking incorrect SSID from old scan results, use
SSID from GO Negotiation to select the AP.
2010-09-09 07:17:23 -07:00
Jouni Malinen
1c9cb49fe9 Trigger WPS configuration update on string changes
Previously, only Device Name string was handled, but similar trigger
is needed on Manufacturer, Model Name, Model Number, and Serial Number
changes.
2010-09-09 07:17:21 -07:00
Jouni Malinen
dcf788d1a4 WPS: Fix configuration strings on config reload
Previously, freed memory could be used as device name (and other similar
parameters) when building WPS IE after SIGHUP.
2010-09-09 07:17:20 -07:00
Jouni Malinen
3c5126a41f P2P: Set Device Password ID in WPS M1/M2 per new rules
If the P2P client (WPS Enrollee) uses a PIN from the GO (Registrar),
Device Password ID in M1 & M2 is set to Registrar-specified.
2010-09-09 07:17:19 -07:00
Jouni Malinen
b22128efdc P2P: Add initial version of P2P Module 2010-09-09 07:17:17 -07:00
Jouni Malinen
2ff99b3c38 P2P: Do not save temporary networks 2010-09-09 07:17:16 -07:00
Jouni Malinen
b2c5a4a3df P2P: Do not filter BSSes based on SSID during P2P Provisioning
TODO: Use group id from GO Neg instead(?)
2010-09-09 07:17:16 -07:00
Jouni Malinen
9fa243b295 P2P: Let WPS code know if it is used in a P2P group 2010-09-09 07:17:16 -07:00
Jouni Malinen
611aea7d41 Allow ctrl_iface SET command to change global config parameters 2010-09-09 07:17:16 -07:00
Jouni Malinen
42f50264c0 WPS: Make fragment size configurable for EAP-WSC peer
"wpa_cli set wps_fragment_size <val>" can now be used to configure the
fragment size limit for EAP-WSC.
2010-09-09 06:07:49 -07:00
Jouni Malinen
ad4741183f WPS 2.0: Make sure PHY/VIRT flag gets set for PBC 2010-09-09 06:07:48 -07:00
Jouni Malinen
54f489be45 WPS 2.0: Validate WPS attributes in management frames and WSC messages
If CONFIG_WPS_STRICT is set, validate WPS IE(s) in management frames and
reject the frames if any of the mandatory attributes is missing or if an
included attribute uses an invalid value. In addition, verify that all
mandatory attributes are included and have valid values in the WSC
messages.
2010-09-09 06:07:48 -07:00
Jouni Malinen
31fcea931d WPS 2.0: Add support for AuthorizedMACs attribute
Advertize list of authorized enrollee MAC addresses in Beacon and
Probe Response frames and use these when selecting the AP. In order
to provide the list, the enrollee MAC address should be specified
whenever adding a new PIN. In addition, add UUID-R into
SetSelectedRegistrar action to make it potentially easier for an AP
to figure out which ER sent the action should there be multiple ERs
using the same IP address.
2010-09-09 06:07:47 -07:00
Jouni Malinen
979b988ed6 WPS: Do not allow Label and Display config methods to be enabled
It is unclear which PIN is used if both Label and Display config
methods are advertised. Avoid this by not allowing such configuration.
2010-07-17 20:30:49 -07:00
Jouni Malinen
41e650ae5c WPS: Use different scan result sorting rules when doing WPS provisioning
The AP configuration may change after provisioning, so it is better
not to use the current security policy to prioritize results. Instead,
use WPS Selected Registrar attribute as the main sorting key and use
signal strength next without considering security policy or rate sets.
The non-WPS provisioning case remains as-is, i.e., this change applies
only when trying to find an AP for WPS provisioning.
2010-06-11 13:50:13 -07:00